Search

Porous copper (Cu), with varying porosities, has been made using carbamide as a space holder through the powder metallurgy route. Two shapes of carbamide particles were used, (i) needlelike and (ii) spherical, in order to investigate the effect of the space holder shape on the pore structure and mechanical properties of porous Cu. The compressive deformation behavior of porous Cu was studied under a compression test. The pores' structural characteristics and mechanical properties of the porous Cu varied significantly with the shape of the space holder. Although the effect of the space holder shape on the porosity was not regular, the effect on the mechanical properties was regular. The stress increased monotonically with the increase in the strain, and strain hardening occurred at the plastic yield stage. The elastic modulus and yield strength followed the power law, with the relative density irrespective of the space holder shape. The empirical constants associated with different empirically developed power law relations were different, according to the shape of space holder. A quantitative relationship between the elastic modulus and yield strength and the spacer content was obtained to control the mechanical properties of the present porous Cu or other porous metals and metal foams using the well-known space holder method. [ABSTRACT FROM AUTHOR]

Ionic liquid modification for carbon-supported platinum (Pt/C) electrocatalysts to enhance their oxygen reduction reaction (ORR) activity has been well recognized. However, the research has only been reported on the low-Pt-loading Pt/C electrocatalysts, e.g., 20 wt%, while in practical applications, usually high-Pt-loading Pt/C electrocatalysts of 45–60 wt% are used. In this work, ionic liquid modification is systematically investigated for a Pt/C electrocatalyst with 60 wt% Pt loading for its ORR activity in the cathode in proton exchange membrane fuel cells (PEMFCs). Various adsorption amounts are studied on the catalyst surface. Different modification behavior is found. Mechanism exploration shows that the adsorption of ionic liquid mainly happens on the Pt electrocatalyst surface and in the micropores of the carbon support. The highest fuel cell power performance is achieved at an ionic liquid loading of 7 wt%, which is much higher than the 3 wt% reported for the low-Pt-loading Pt/C. [ABSTRACT FROM AUTHOR]

Aiming at the problem of large measurement error and phase shift in resistance voltage dividers under high-frequency conditions in the field of power measurement, such as power harmonics, an error correction method is proposed for an alternating current (AC) resistance voltage divider based on the equivalence principle. Firstly, the frequency error model of the AC resistance voltage divider precision is established, and the angle difference of the continuous spectrum ratio difference from 50 Hz to 100 kHz is corrected by determining the shielding structure and the resistance parameters and fine-tuning the shielding potential correction method to reduce the capacities error of the AC resistance voltage divider design precision. At the same time, the performance parameters such as the direction and magnitude of the shielding potential compensation capacitive error are investigated. Finally, the precision voltage divider (the maximum voltage applied is 480 V) calibration experiments verify that the important characteristic judgment factor of the voltage divider is independent of the frequency and the equivalent capacitance value, which effectively solves the phase correction problem of harmonic power measurement. [ABSTRACT FROM AUTHOR]

Dental caries is a common and costly multifactorial biofilm disease caused by cariogenic bacteria that ferment carbohydrates to lactic acid, demineralizing the inorganic component of teeth. Therefore, low pH (pH 4.5) is a characteristic signal of the localised carious environment, compared to a healthy oral pH range (6.8 to 7.4). The development of pH-responsive delivery systems that release antibacterial agents in response to low pH has gained attention as a targeted therapy for dental caries. Release is triggered by high levels of acidogenic species and their reduction may select for the establishment of health-associated biofilm communities. Moreover, drug efficacy can be amplified by the modification of the delivery system to target adhesion to the plaque biofilm to extend the retention time of antimicrobial agents in the oral cavity. In this review, recent developments of different pH-responsive nanocarriers and their biofilm targeting mechanisms are discussed. This review critically discusses the current state of the art and innovations in the development and use of smart delivery materials for dental caries treatment. The authors' views for the future of the field are also presented. [ABSTRACT FROM AUTHOR]

Micromanipulation is a powerful technique to measure the mechanical properties of microparticles including microcapsules. For microparticles with a homogenous structure, their apparent Young's modulus can be determined from the force versus displacement data fitted by the classical Hertz model. Microcapsules can consist of a liquid core surrounded by a solid shell. Two Young's modulus values can be defined, i.e., the one is that determined using the Hertz model and another is the intrinsic Young's modulus of the shell material, which can be calculated from finite element analysis (FEA). In this study, the two Young's modulus values of microplastic-free plant-based microcapsules with a core of perfume oil (hexyl salicylate) were calculated using the aforementioned approaches. The apparent Young's modulus value of the whole microcapsules determined by the classical Hertz model was found to be EA = 0.095 ± 0.014 GPa by treating each individual microcapsule as a homogeneous solid spherical particle. The previously obtained simulation results from FEA were utilised to fit the micromanipulation data of individual core–shell microcapsules, enabling to determine their unique shell thickness to radius ratio (h/r)FEA = 0.132 ± 0.009 and the intrinsic Young's modulus of their shell (EFEA = 1.02 ± 0.13 GPa). Moreover, a novel theoretical relationship between the two Young's modulus values has been derived. It is found that the ratio of the two Young's module values (EA/EFEA) is only a function on the ratio of the shell thickness to radius (h/r) of the individual microcapsule, which can be fitted by a third-degree polynomial function of h/r. Such relationship has proven applicable to a broad spectrum of microcapsules (i.e., non-synthetic, synthetic, and double coated shells) regardless of their shell chemistry. [ABSTRACT FROM AUTHOR]

Microparticles are widely used in many industrial sectors. A micromanipulation technique has been widely used to quantify the mechanical properties of individual microparticles, which is crucial to the optimization of their functionality and performance in end-use applications. The principle of this technique is to compress single particles between two parallel surfaces, and the force versus displacement data are obtained simultaneously. Previously, analysis of the experimental data had to be done manually to calculate the rupture strength parameters of each individual particle, which is time-consuming. The aim of this study is to develop a software package that enables automatic analysis of the rupture strength parameters from the experimental data to enhance the capability of the micromanipulation technique. Three algorithms based on the combination of the "three-sigma rule", a moving window, and the Hertz model were developed to locate the starting point where onset of compression occurs, and one algorithm based on the maximum deceleration was developed to identify the rupture point where a single particle is ruptured. Fifty microcapsules each with a liquid core and fifty porous polystyrene (PS) microspheres were tested in order to produce statistically representative results of each sample, and the experimental data were analysed using the developed software package. It is found that the results obtained from the combination of the "3σ + window" algorithm or the "3σ + window + Hertz" algorithm with the "maximum-deceleration" algorithm do not show any significant difference from the manual results. The data analysis time for each sample has been shortened from 2 to 3 h manually to within 20 min automatically. [ABSTRACT FROM AUTHOR]

In this study, vacuum low-pressure carburizing heat treatments were carried out on 18Cr2Ni4WA case-carburized alloy steel. The evolution and phase transformation mechanism of the microstructure of the carburized layer during low-temperature tempering and its effect on the surface hardness were studied. The results showed that the carburized layer of the 18Cr2Ni4WA steel was composed of a large quantity of martensite and retained austenite. The type of martensite matrix changed from acicular martensite to lath martensite from the surface to the core. The hardness of the carburized layer gradually decreased as the carbon content decreased. A thermodynamic model was used to show that the low-carbon retained austenite was easier to transform into martensite at lower temperatures, since the high-carbon retained austenite was more thermally stable than the low-carbon retained austenite. The mechanical stability—not the thermal stability—of the retained austenite in the carburized layer dominated after carburizing and quenching, and cryogenic treatment had a limited effect on promoting the martensite formation. During low-temperature tempering, the solid-solution carbon content of the martensite decreased, the compressive stress on the retained austenite was reduced and the mechanical stability of the retained austenite decreased. Therefore, during cooling after low-temperature tempering, the low-carbon retained austenite transformed into martensite, whereas the high-carbon retained austenite still remained in the microstructure. The changes in the martensite matrix hardness had a far greater effect than the transformation of the retained austenite to martensite on the case hardness of the carburized layer. [ABSTRACT FROM AUTHOR]

Polymeric microspheres with different internal structures have been widely used because of their characteristics in the structures. This paper reports a method of controlling the internal structures of polymeric microspheres via the introduction of a water-soluble organic solvent to the continuous phase in the foam phase preparation of porous polymeric microspheres. The introduction of a water-soluble organic solvent enables the control of polymeric microspheres’ internal structures, from porous to hollow. Because a water-soluble organic solvent is introduced, the organic solvent may be diffused toward the interface because of the affinity between the organic solvent and the oil droplets, resulting an accumulation of organic solvent molecules at the interface to form an organic solvent layer. The presence of this layer may decrease the evaporation rate of the internal organic solvent in an oil droplet, which extends the time for the mingling of porogen droplets to form a few large pores or even an extremely large single pore inside. This method is also capable of altering the thickness of hollow microspheres’ shells in a desired way, with improved efficiency, yield and the capacity for continuous use on an industrial scale. [ABSTRACT FROM AUTHOR]

Some cytochrome P450 (CYP) genes are known for their rapid up-regulation in response to insecticide exposures in insects. To date, however, limited information is available with respect to the relationships among the insecticide type, insecticide concentration, exposure duration and the up-regulated CYP genes. In this study, we examined the transcriptional response of eight selected CYP genes, including CYP4G7, CYP4Q4, CYP4BR3, CYP12H1, CYP6BK11, CYP9D4, CYP9Z5 and CYP345A1, to each of four insecticides in the red flour beetle, Tribolium castaneum. Reverse transcription quantitative PCR (RT-qPCR) revealed that CYP4G7 and CYP345A1 can be significantly up-regulated by cypermethrin (1.97- and 2.06-fold, respectively), permethrin (2.00- and 2.03-fold) and lambda-cyhalothrin (1.73- and 1.81-fold), whereas CYP4BR3 and CYP345A1 can be significantly up-regulated by imidacloprid (1.99- and 1.83-fold) when 20-day larvae were exposed to each of these insecticides at the concentration of LC20 for 24 h. Our studies also showed that similar levels of up-regulation can be achieved for CYP4G7, CYP4BR3 and CYP345A1 by cypermethrin, permethrin, lambda-cyhalothrin or imidacloprid with approximately one fourth of LC20 in 6 h. Our study demonstrated that up-regulation of these CYP genes was rapid and only required low concentrations of insecticides, and the up-regulation not only depended on the CYP genes but also the type of insecticides. Our results along with those from previous studies also indicated that there were no specific patterns for predicting the up-regulation of specific CYP gene families based on the insecticide classification.