Search

Because low thermal conductivity and high viscosity are common characteristics of austenitic steel, it is easy to cause a large amount of heat accumulation in the chip area, resulting in tool edge collapse or wear, and the traditional preparation method is unsuitable for preparing large and complex austenitic steel components. Wire + arc additive manufacturing (WAAM) provides a great application value for austenitic stainless steel because it can solve this problem. The cold metal transfer (CMT)-WAAM system with good control of heat input was used to fabricate the multi-trace and multilayer stainless steel 321 (SS 321) workpiece in this study. The microstructure and corrosion properties of the SS 321 workpiece were observed and compared with those of an SS 321 sheet. The results showed that the microstructure of the SS 321 workpiece from top to bottom was regularly and periodically repeated from the overlapping remelting zone, inter-layer remelting zone, and primary melting zone. There was white austenite matrix and black ferrite, and a small amount of skeleton and worm ferrite was distributed on the white austenite matrix. The average hardness value from the top to the bottom region was approximately uniform, indicating that the workpiece had good consistency. The corrosion properties in 0.5 mol/L H2SO4 solutions were compared between the SS 321 workpiece and the SS 321 sheet. The results showed that the corrosion properties of the top region of the workpiece were better than that of the middle and bottom part, and the corrosion properties of the SS 321 workpiece were better than that of the SS 321 sheet. [ABSTRACT FROM AUTHOR]

In this work, an Inconel 625 thin-wall structure was fabricated by the gas tungsten arc welding (GTAW) hot-wire arc additive manufacturing process. The microstructure and mechanical properties of the Inconel 625 samples, extracted from different orientations and locations of the thin-wall structure, were investigated and compared. The results showed that the additively manufactured Inconel 625 component, made by hot-wire GTAW, had good quality. Its microstructure consisted of dendrites, equiaxial crystals, and cellular crystals. The average hardness from the bottom to the top was similar, indicating that the thin wall had good consistency. The plasticity in the deposition direction was better than those in the other three regions, which was related to the dendritic structure in the sedimentary direction. [ABSTRACT FROM AUTHOR]

Plasma arc welding (PAW)-cable-type seven-wire GMAW (gas metal arc welding) hybrid welding is known as a high-efficiency welding combining plasma arc, GMAW arc and cable-type welding wire. In this study, numerical simulation via Fluent of the molten pool temperature field and flow field and experimental verification were conducted on Q235 thin plate hybrid welding with cable-type wire to explore molten pool fluid behavior. The simulation results show that keyholes form in the molten pool due to the strong penetration ability of a plasma arc and then the evolved pores by the surface tension float out of the molten pool. When the GMAW welding current increases, both the length and width of the weld pool enlarge, the weld reinforcement increases and the flow rate of molten metal in the weld pool also speeds up. While the PAW current increases, the weld pool length also increases and the molten metal in the weld pool significantly flows faster, but the weld reinforcement decreases. When the welding speed increases, the weld pool length and fusion depth decrease, but the reinforcement will first increase and then decrease. The experimental results are in strong agreement with the simulation results. It shows that the numerical analysis model established in this paper is accurate, laying a certain theoretical foundation for the popularization of PAW-cable-type seven-wire GMAW hybrid welding. [ABSTRACT FROM AUTHOR]

The microstructure and corrosion resistance of samples fabricated by Q345 and 308 bimetallic feedings using two kinds of processes of wire-arc additive manufacturing (WAAM) was observed and compared with that of sample manufactured by a single feeding wire of Q345 or 308. The results show that the interface between the Q345 and 308 had no defects and metallurgical bonding. The hardness of bimetal Q345/308 additive manufacturing samples was higher than that of Q345 or 308 single wire additive manufacturing. The sample made of Q345 single wire had serious electrochemical corrosion, while the sample made of 308 single wire had pitting corrosion. The pitting corrosion of the sample reinforced by bimetal Q345/308 feeding wires was improved. [ABSTRACT FROM AUTHOR]

CoCrFeNiSiMoW medium-entropy alloy coatings (MEACs) were fabricated by plasma-arc surfacing welding on Q235 steel. The microstructures and mechanical properties of CoCrFeNiSiMoW MEACs were studied. CoCrFeNiSiMoW MEACs are made from a mixture of NiCrCoMo cubic (FCC) solid solution phase, (Fe, Ni), Mo1.24Ni0.76, and CoCx phases by XRD analysis. The average hardness values of the one- and two-layer CoCrFeNiSiMoW MEACs obtained were 186 ± 1.56 and 198 ± 1.78 HV, respectively. Compared with the one-layer CoCrFeNiSiMoW coating, the two-layer coating has a better wear performance due to its higher hardness. Its corrosion resistance is better because of its higher Ni content. [ABSTRACT FROM AUTHOR]

In this study, CoCrFeMnNiW medium-entropy alloy coating on Q235 was fabricated by plasma surfacing technology. The wear performance of the prepared one-layer coating and the two-layer coating was studied by a friction and abrasion tester. The microstructure and performance of the CoCrFeMnNiW coating were researched by optical microscope, a nano-indentation test, SEM, and hardness tester. The results show that the microstructure of the coating is made up of a fusion zone, equiaxed dendrites near the fusion zone, coarse columnar crystals, and near-surface with a certain direction between the near-fusion zone and near-surface fine equiaxed grains. The wear mechanism of one layer coating was abrasive with wear and fatigue wear. The wear mechanism of the two-layer coating was adhesive with wear and fatigue wear. For CoCrFeMnNiW MEA coating, the main factors determining their wear resistance were the value of its depth recovery ratio (ηh) and EIT. [ABSTRACT FROM AUTHOR]

Considering the coupling of a droplet, keyhole, and molten pool, a three-dimensional transient model for the full penetration laser + metal inert gas (MIG) hybrid welding of thin copper alloy plate was established, which is able to simulate the temperature and velocity fields, keyhole behavior, and generation of the welding defect. Based on the experimental and simulation results, the weld formation mechanism for the hybrid butt welding of a 2 mm-thick copper alloy plate was comparatively studied in terms of the fluid dynamic feature of the melt pool. For single laser welding, the dynamic behavior of liquid metal near the rear keyhole wall is complex, and the keyhole has a relatively drastic fluctuation. An obvious spattering phenomenon occurs at the workpiece backside. Meanwhile, the underfill (or undercut) defect is formed at both the top and bottom surfaces of the final weld bead, and the recoil pressure is identified as the main factor. In hybrid welding, a downward fluid flow is strengthened on the rear keyhole wall, and the stability of the keyhole root is enhanced greatly. There are large and small clockwise vortexes emerging in the upper and lower parts of the molten pool, respectively. A relatively stable metal bulge can be produced at the weld pool backside. The formation defects are suppressed effectively, increasing the reliability of full penetration butt welding of the thin copper alloy plate. [ABSTRACT FROM AUTHOR]

A three-dimensional numerical model is used to simulate heat transfer and fluid flow phenomena in fiber laser + gas metal arc welding (GMAW) hybrid welding of an aluminum alloy, which incorporates three-phase coupling and is able to depict the keyhole dynamic behavior and formation process of the keyhole-induced porosity. The temperature profiles and fluid flow fields for different arc powers are calculated and the percent porosities of weld beads were also examined under different conditions by X-ray non-destructive testing (NDT). The results showed that the computed results were in agreement with the experimental data. For hybrid welding, with raising arc power, the keyhole-induced porosity was reduced. Besides the solidification rate of the molten pool, the melt flow was also closely related to weld porosity. A relatively steady anti-clockwise vortex caused by arc forces tended to force the bubble to float upwards at the high temperature region close to the welding heat source, which benefits the escape of the gas bubble from the melt pool. When increasing the arc power, the anti-clockwise region was strengthened and the risk of the gas bubble for capture by the liquid/solid interface underneath the keyhole tip was diminished, which resulted in the lower weld percent porosity. [ABSTRACT FROM AUTHOR]