Search

Vacuum induction melting in a refractory crucible is an economical method to produce TiAl-based alloys, aiming to reduce the preparation cost. In this paper, a Sr2CeZrO6 refractory was synthesized by a solid-state reaction method using SrCO3, CeO2 and ZrO2 as raw materials, and its interaction with TiAl alloy melt was investigated. The results showed that a single-phase Sr2CeZrO6 refractory could be fabricated at 1400 °C for 12 h, and its space group was Pnma with a = 5.9742(3) Å, b = 8.3910(5) Å and c = 5.9069(5) Å. An interaction layer with a 40μm thickness and dense structure could be observed in Sr2CeZrO6 crucible after melting TiAl alloy. Additionally, the interaction mechanism showed that the Sr2CeZrO6 refractory dissolved in the alloy melt, resulting in the generation of Sr3Zr2O7, SrAl2O4 and CeO2−x, which attached to the surface of the crucible. [ABSTRACT FROM AUTHOR]

Innovative technologies require the use of materials that meet increasingly high requirements; one such requirement is the purity of metals. In the case of copper, this translates into a parameter related to electrical conductivity. Traditional metal refining technologies have some limitations that can be eliminated through the use of modern melting aggregates. Such solutions include vacuum induction furnaces, comprising an induction furnace with a cold crucible. As part of this work, the possibilities of refining copper and lead alloys were investigated. In addition, the research was carried out with the use of two induction vacuum aggregates, allowing us to compare their effectiveness. The tests were carried out in a pressure range of 10–1000 Pa and at temperatures of 1273–1473 K. The results obtained made it possible to determine the mass transport coefficient of lead from an alloy with copper, and to determine the share of resistance in individual stages of the process. For experiments conducted inside an induction crucible furnace, lowering the working pressure inside the furnace chamber from 1000 to 10 Pa while increasing the temperature from 1323 to 1473 K was accompanied by a drop in the lead concentration inside the alloy of 69 to 96%, compared to its initial mass. For experiments conducted inside a cold crucible furnace, approximate values of lead removal appeared for lower temperatures (1273 to 1323 K), confirming that the analyzed process happens faster in this aggregate. [ABSTRACT FROM AUTHOR]

The aim of this work was to obtain dense Cu2S superionic thermoelectric materials, homogeneous in terms of phase and chemical composition, using a very fast and cheap induction-melting technique. The chemical composition was investigated via scanning electron microscopy (SEM) combined with an energy-dispersive spectroscopy (EDS) method, and the phase composition was established by X-ray diffraction (XRD). The thermoelectric figure of merit ZT was determined on the basis of thermoelectric transport properties, i.e., Seebeck coefficient, electrical and thermal conductivity in the temperature range of 300–923 K. The obtained values of the ZT parameter are comparable with those obtained using the induction hot pressing (IHP) technique and about 30–45% higher in the temperature range of 773–923 K in comparison with Cu2S samples densified with the spark plasma sintering (SPS) technique. [ABSTRACT FROM AUTHOR]

The effect of Ta and W additions on microstructure and mechanical properties of tilt-cast Ti-45Al-5Nb-2C (at.%) alloy was investigated. Three alloys with nominal composition Ti-45Al-5Nb-2C-2X (in at.%), where X is Ta or W, were prepared by vacuum induction melting in graphite crucibles followed by tilt casting into graphite moulds. The microstructure of the tilt-cast alloys consists of the α2(Ti3Al) + γ(TiAl) lamellar grains, single γ phase, (Ti,Nb,X)2AlC particles with a small amount of (Ti,Nb,X)C, and β/B2 phase identified only in W containing alloy. The EDS analysis shows that Ta segregates into the carbide particles and reduces dissolution of Nb in both (Ti,Nb,Ta)C and (Ti,Nb,Ta)2AlC phases. The alloying with W reduces Nb content in both carbide phases and leads to stabilisation of β/B2 phase in the lamellar α2 + γ regions. The alloying with Ta and W does not affect the volume fraction of the carbide particles but influences their size and morphology. While the alloying with Ta and W has no significant effect on Vickers hardness and the indentation elastic modulus of the studied alloys, the addition of Ta affects the nanohardness and elastic modulus of the (Ti,Nb,Ta)2AlC phase. The addition of W significantly increases the Vickers microhardness of the lamellar α2 + γ regions. [ABSTRACT FROM AUTHOR]

Many nuclear power plants (NPP) facilities have aged and are being dismantled around the world. As a result, large amounts of radioactive metal waste are generated during decommissioning. Carbon steel, stainless steel, and Inconel are the most common metals used in NPP, and radioactive contaminants are mostly accumulated in the corrosion layer. There are various radionuclides, but the main ones are 60Co, 137Cs, 54Mn and 51Cr. 60Co is the major activated corrosion product and responsible for high gamma radiation and longer half-life (5.27 years.) also makes it the most difficult to remove. Therefore, we investigated the melt decontamination characteristics of 60Co by introducing various slags using induction melting for stainless steel and carbon steel. Cobalt plating and cobalt oxide film coatings were used as specimens instead for safety purposes. The amount of cobalt removed from the slag was analyzed by using XRF. About 11% of the cobalt was removed from the contaminated metal due to slag oxide formation. The distribution of cobalt in the melted metal was also almost homogeneous according to the XRD analysis. [ABSTRACT FROM AUTHOR]

This paper presents the chemical and phase composition, microstructure, and selected properties both at room temperature and at the temperature corresponding to the expected operating conditions of three successive generations of TiAl-based alloys (Ti-47Al-2W-0.5Si, Ti-45Al-8Nb-0.5(B,C), and Ti-45Al-5Nb-2Cr-1Mo-0.5(B,C)-0.2Si) melted in a vacuum induction furnace with high-density isostatic pressed graphite crucibles. The obtained results of mechanical and physical properties of the produced alloys were compared to the properties of reference alloys with similar chemical composition and melted in a cold copper crucible furnace. The effect of increased carbon content in the produced alloys due to the degradation of the graphite crucible during melting is higher strength properties, lower plastic properties, higher coefficient of thermal expansion, and improved creep resistance. It was shown that the proposed technology could be successfully used in the production of different generation TiAl-based intermetallic alloys. [ABSTRACT FROM AUTHOR]

Hot working is a key process in the production of superalloys; however, it may result in the formation of inclusions that affect the superalloy performance. Therefore, the effects of hot working on inclusions in a superalloy must be studied. GH4738 superalloy was manufactured, herein, by vacuum induction melting and vacuum arc remelting. Hot working was performed by unidirectional drawing, upsetting and drawing, and upsetting/drawing with radial forging. The types and distributions of inclusions after these three hot working processes and those in an original ingot were analyzed using scanning electron microscopy, energy dispersive spectroscopy, and Image-Pro Plus software. The results showed that the melting technology essentially determined the inclusion types in GH4738. Four types of inclusions were found in the experiments: TiC–TiN–Mo–S composite, TiC–TiN composite, Ce–Mo–S composite, and SiC inclusions. In the case of hot working by unidirectional drawing, the average inclusion size first decreased, and then increased from the center to the edge. In the case of upsetting and drawing, and upsetting/drawing with radial forging, the average inclusion size decreased from the center to the edge. [ABSTRACT FROM AUTHOR]