Search

The demand for eco-friendly packaging materials has urged researchers to look for alternatives to petroleum-based polymers. In this regard, paper-based products have turned out to be a promising choice; however, their weak resistance to water has limited their application. The use of various additives to enhance paper's moisture resistance is a common practice. However, considering the growing global agenda for sustainable development, the search for new bio-based paper additives has become increasingly important. This study investigated the potential synergistic impact of the addition of nanofibrillated cellulose (NFC) and chitosan additives (CHIT) to different fiber combinations to improve paper's properties, in particular, their wet strength. The efficacy of the additive application order was examined and was found to be crucial in achieving the desired outcomes. The results showed that incorporating CHIT after NFC enhanced the paper's tensile and burst indicators, as well as the paper stretch in the dry state, by 35–70%, 35–55%, and 20–35%, respectively. In addition, the tensile index and stretch in the wet state improved 9–13 times and 2.5–5.5 times over, respectively. The air permeability decreased 2.5–12 times over. These findings demonstrate that the sequential addition of the NFC and CHIT additives yield a greater enhancement of paper's properties than using each additive separately. [ABSTRACT FROM AUTHOR]

A significant increase in the consumption of recycled fiber products has been observed worldwide, and the industry is forced to solve the challenges of recycled fiber quality and add strength agents and/or virgin fibers to reach sufficient properties. In order to investigate whether the mechanical and air permeability properties of waste fiber (WF) material can be significantly improved by adding wood kraft fibers (KF), hemp soda fibers (HF), and ammonium persulfate oxidated cellulose nanofibrils (CNF), different fiber blends were prepared and tested. Results revealed the excellence of hemp fibers over wood fibers regarding the improvement of WF products. The results of WF after the addition of 10% mixed fibers (KF + HF) were higher than the results of a 50% KF addition. The impact of CNF depended on fiber composition and properties. A formula for modeling the CNF impact on different fiber compositions was proposed. Obtained fiber material samples showed suitability for home composting, thus contributing to the goals of the European Green Deal regarding reducing landfill waste and the development of cleaner products. [ABSTRACT FROM AUTHOR]

This study investigates the mycelial biomass production and chitosan extraction potential of various Basidiomycota strains, including Heterobasidion annosum, Phanerochaete chrysosporium, Pleurotus ostreatus, Trametes versicolor, and Lentinus lepideus. Both submerged fermentation (SF) and solid-state fermentation (SSF) methods were employed. The chitosan yield in basidiocarps of Pleurotus ostreatus, Agaricus bisporus, and Ganoderma applanatum was also evaluated as a reference material. The chitosan extracted from fungal cells was characterized using elemental analyses and FTIR spectroscopy. Among the cultivated strains, P. chrysosporium exhibited the highest mycelial biomass concentration in SF (1.03 g 100 mL–1) after 14 days, while T. versicolor achieved the highest biomass concentration in SSF (3.65 g 100 mL–1). The highest chitosan yield was obtained from the mycelium of P. chrysosporium (0.38%) and T. versicolor (0.37%) in shaken SF. Additionally, commercially cultivated A. bisporus demonstrated the highest chitosan yield in fungal fruiting bodies (1.7%). The extracted chitosan holds potential as a functional biopolymer additive for eco-friendly materials, serving as an alternative to synthetic wet and dry strength agents in packaging materials. [ABSTRACT FROM AUTHOR]

In this study, novel blends of mycelium biocomposites (MB) were developed. Various combinations of birch sawdust and hemp shives with birch bark (BB) and wheat bran (WB) additives were inoculated with basidiomycete Trametes versicolor to produce self-growing biomaterials. MB were characterized according to mycelial biomass increment in final samples, changes in chemical composition, elemental (C, H, N) analyses, granulometry of substrates, water-related and mechanical properties, as well as mold resistance and biodegradability. The mycelial biomass in manufactured MB increased by ~100% and ~50% in hemp and sawdust substrates, respectively. The lignocellulose ingredients during fungal growth were degraded as follows: cellulose up to 7% and 28% in sawdust and hemp substrates, respectively, and lignin in the range of 13% in both substrates. A larger granulometric fraction in hemp MB ensured higher strength property but weakened water absorption (600–880%) performance. Perspective MB combinations regarding strength performance were hemp/BB and pure hemp MB (σ10 0.19–0.20 MPa; E 2.9 MPa), as well as sawdust/WB combination (σ10 0.23 MPa; E 2.9 MPa). WB positively affected fungal biomass yield, but elevated water absorption ability. WB improved compressive strength in the sawdust samples but decreased it in the hemp samples. BB supplement reduced water absorption by more than 100% and increased the density of sawdust and hemp samples. All MB samples were susceptible to mold contamination after full water immersion, with identified fungal genera Rhizopus, Trichoderma and Achremonium. The MB exhibited high biodegradability after 12 weeks' exposure in compost, and are therefore competitive with non-biodegradable synthetic foam materials. [ABSTRACT FROM AUTHOR]

Durability-based designs with timber require reliable information about the wood properties and how they affect its performance under variable exposure conditions. This study aimed at utilizing a material resistance model (Part 2 of this publication) based on a dose–response approach for predicting the relative decay rates in above-ground situations. Laboratory and field test data were, for the first time, surveyed globally and used to determine material-specific resistance dose values, which were correlated to decay rates. In addition, laboratory indicators were used to adapt the material resistance model to in-ground exposure. The relationship between decay rates in- and above-ground, the predictive power of laboratory indicators to predict such decay rates, and a method for implementing both in a service life prediction tool, were established based on 195 hardwoods, 29 softwoods, 19 modified timbers, and 41 preservative-treated timbers. [ABSTRACT FROM AUTHOR]

Service life planning with timber requires reliable models for quantifying the effects of exposure-related parameters and the material-inherent resistance of wood against biotic agents. The Meyer-Veltrup model was the first attempt to account for inherent protective properties and the wetting ability of wood to quantify resistance of wood in a quantitative manner. Based on test data on brown, white, and soft rot as well as moisture dynamics, the decay rates of different untreated wood species were predicted relative to the reference species of Norway spruce (Picea abies). The present study aimed to validate and optimize the resistance model for a wider range of wood species including very durable species, thermally and chemically modified wood, and preservative treated wood. The general model structure was shown to also be suitable for highly durable materials, but previously defined maximum thresholds had to be adjusted (i.e., maximum values of factors accounting for wetting ability and inherent protective properties) to 18 instead of 5 compared to Norway spruce. As expected, both the enlarged span in durability and the use of numerous and partly very divergent data sources (i.e., test methods, test locations, and types of data presentation) led to a decrease in the predictive power of the model compared to the original. In addition to the need to enlarge the database quantity and improve its quality, in particular for treated wood, it might be advantageous to use separate models for untreated and treated wood as long as the effect of additional impact variables (e.g., treatment quality) can be accounted for. Nevertheless, the adapted Meyer-Veltrup model will serve as an instrument to quantify material resistance for a wide range of wood-based materials as an input for comprehensive service life prediction software. [ABSTRACT FROM AUTHOR]

In this study unique blended biopolymer mycocel from naturally derived biomass was developed. Softwood Kraft (KF) or hemp (HF) cellulose fibers were mixed with fungal fibers (FF) in different ratios and the obtained materials were characterized regarding microstructure, air permeability, mechanical properties, and virus filtration efficiency. The fibers from screened Basidiomycota fungi Ganoderma applanatum (Ga), Fomes fomentarius (Ff), Agaricus bisporus (Ab), and Trametes versicolor (Tv) were applicable for blending with cellulose fibers. Fungi with trimitic hyphal system (Ga, Ff) in combinations with KF formed a microporous membrane with increased air permeability (>8820 mL/min) and limited mechanical strength (tensile index 9–14 Nm/g). HF combination with trimitic fungal hyphae formed a dense fibrillary net with low air permeability (77–115 mL/min) and higher strength 31–36 Nm/g. The hyphal bundles of monomitic fibers of Tv mycelium and Ab stipes made a tight structure with KF with increased strength (26–43 Nm/g) and limited air permeability (14–1630 mL/min). The blends KF FF (Ga) and KF FF (Tv) revealed relatively high virus filtration capacity: the log10 virus titer reduction values (LRV) corresponded to 4.54 LRV and 2.12 LRV, respectively. Mycocel biopolymers are biodegradable and have potential to be used in water microfiltration, food packaging, and virus filtration membranes. [ABSTRACT FROM AUTHOR]

Novel biobased materials from fungal hyphae and cellulose fibers have been proposed to address the increasing demand for natural materials in personal protective equipment (PPE). Materials containing commercially available kraft fibers (KF), laboratory-made highly fibrillated hemp fibers (HF) and fungal fibers (FF) obtained from fruiting bodies of lignicolous basidiomycetes growing in nature were prepared using paper production techniques and evaluated for their mechanical and air permeability properties. SEM and microscopy revealed the network structure of materials. The tensile index of materials was in the range of 8–60 Nm/g and air permeability ranged from 32–23,990 mL/min, depending on the composition of materials. HF was the key component for strength; however, the addition of FF to compositions resulted in higher air permeability. Chemical composition analysis (Fourier-transform infrared spectroscopy) revealed the presence of natural polysaccharides, mainly cellulose and chitin, as well as the appropriate elemental distribution of components C, H and N. Biodegradation potential was proven by a 30-day-long composting in substrate, which resulted in an 8–62% drop in the C/N ratio. Conclusions were drawn about the appropriateness of fungal hyphae for use in papermaking-like technologies together with cellulose fibers. Developed materials can be considered as an alternative to synthetic melt and spun-blown materials for PPE. [ABSTRACT FROM AUTHOR]

Novel biobased materials from fungal hyphae and cellulose fibers have been proposed to address the increasing demand for natural materials in personal protective equipment (PPE). Materials containing commercially available kraft fibers (KF), laboratory-made highly fibrillated hemp fibers (HF) and fungal fibers (FF) obtained from fruiting bodies of lignicolous basidiomycetes growing in nature were prepared using paper production techniques and evaluated for their mechanical and air permeability properties. SEM and microscopy revealed the network structure of materials. The tensile index of materials was in the range of 8-60 Nm/g and air permeability ranged from 32-23,990 mL/min, depending on the composition of materials. HF was the key component for strength; however, the addition of FF to compositions resulted in higher air permeability. Chemical composition analysis (Fourier-transform infrared spectroscopy) revealed the presence of natural polysaccharides, mainly cellulose and chitin, as well as the appropriate elemental distribution of components C, H and N. Biodegradation potential was proven by a 30-day-long composting in substrate, which resulted in an 8-62% drop in the C/N ratio. Conclusions were drawn about the appropriateness of fungal hyphae for use in papermaking-like technologies together with cellulose fibers. Developed materials can be considered as an alternative to synthetic melt and spun-blown materials for PPE.