Search

Pellet burners, although they are commonly used devices, require high-quality fuels and yet are characterized by relatively high levels of CO and NO emissions and their variability. This article presents a combustion study of an original biomass burner that separates air into primary for biomass gasification and secondary for oxidizing the gasification products, with ducts placed in the housing of the burner. This study introduces a new burner design that separates air into primary and secondary streams within an integrated burner housing, aiming to optimize biomass combustion efficiency and reduce harmful emissions. Two burner designs were proposed, with a high secondary air nozzle (HCrown) and a low secondary air nozzle (LCrown). These two burners were compared with a typical retort burner (Ret). The LCrown burner reduced particulate matter emissions by 36% and CO emissions by 74% with respect to a typical retort burner. This study showed that the distance of the secondary air nozzles from the gasifying part has a significant impact on the operation of the burner and the possibility of reducing emissions of CO and NO. These results highlight the potential of the innovation to significantly improve combustion quality while simultaneously reducing environmental impact. [ABSTRACT FROM AUTHOR]

This study explores the intersection of waste management and sustainable fuel production, focusing on the pyrolysis of plastic waste, specifically polystyrene. We examine the physicochemical parameters of the resulting waste plastic pyrolytic oils (WPPOs), blended with kerosene to form a potential alternative fuel for gas turbines. Our findings reveal that all WPPO blends lead to increased emissions, with NOX rising by an average of 61% and CO by 25%. Increasing the proportion of WPPO also resulted in a higher exhaust gas temperature, with an average rise of 12.2%. However, the thrust-specific fuel consumption (TSFC) decreased by an average of 13.8%, impacting the overall efficiency of waste-derived fuels. This study underscores the need for integrated waste-to-energy systems, bridging the gap between waste management and resource utilization. [ABSTRACT FROM AUTHOR]

To improve the in situ soil stabilization, different chemical additives are used (ion exchange compounds, additives based on H2SO4 or vinyl polymers, and organic additives using lignosulfonates). One interesting alternative is the production of additives from various waste materials. The extensive testing of waste-based blends with soil was performed; the mechanical (unconfined compressive strength (UCS)) and hydraulic (capillary rise, water absorption, and frost resistance (FR)) soil properties were measured. The optimization process led to obtaining additive compositions ensuring high strength and sealing properties: by-pass ash from the ceramics industry, waste H2SO4, pyrolytic waxes/oils from waste mixed plastics, waste tires and HDPE, and emulsion from chewing gum waste. For sandy soil, the following additives were the most promising: emulsion from pyrolytic wax (EPW) from waste PE foil (WPEF) with the addition of waste H2SO4, pyrolytic-oil emulsion from waste tires, EPW from waste mixed plastics with the addition of "by-pass" waste ash and NaOH, EPW from WPEF with the addition of NaOH, and EPW from WPEF reaching up to 93% FR, a 79.6% 7-day UCS increase, and a 27.6% of 28-day UCS increase. For clay: EPW from WPEF with the addition of NaOH, EPW from WPEF with the addition of waste H2SO4, and solely EPW from WPEF reaching up to 7.5% FR, an 80.7% 7-day UCS increase, and a 119.1% 28-day UCS increase. [ABSTRACT FROM AUTHOR]

The torrefaction process represents a thermal conversion technique conducted at relatively low temperatures ranging between 200 to 300 °C. Its objective is to produce fuel with a higher energy density by decomposing the reactive portion of hemicellulose. In this study, the kinetics of mass loss during torrefaction were investigated for willow. The experiments were carried out under isothermal conditions using thermogravimetric analysis. Batch torrefaction reactor designs were conducted and explained in detail. Co-combustion of willow with hard coal (origin: Katowice mine) in different mass ratios (25% biomass + 75% coal, 50% biomass + 50% coal, and 75% biomass + 25% coal) was conducted in addition to raw biomass torrefaction. TG/MS analysis (a combination of thermogravimetric analysis with mass spectrometry analysis) was performed in the research. The optimal torrefaction conditions for willow were identified as an average temperature of 245 °C and a residence time of 14 min, resulting in the lowest mass loss (30.15%). However, it was noted that the composition of torgas, a by-product of torrefaction, presents challenges in providing a combustible gas with sufficient heat flux to meet the energy needs of the process. Prolonged residence times over 15 min and higher average temperatures above 250 °C lead to excessive energy losses from volatile torrefaction products, making them suboptimal for willow. On the other hand, the co-combustion of torrefied biomass with hard coal offers advantages in reduced sulfur emissions but can lead to increased NOx emissions when biomass with a higher nitrogen content is co-combusted in proportions exceeding 50% biomass. This paper summarizes findings related to optimizing torrefaction conditions, challenges in torgas composition, and the emissions implications of co-combustion. [ABSTRACT FROM AUTHOR]

Biomass liquefaction is a well-known and extensively described process. Hydrothermal processes are well understood and can be used in the fuel industry. The use of organic solvents can result in full-fledged products for use in the synthesis of polyurethanes. The plastics industry, including polyurethanes, is targeting new, more environmentally friendly solutions. One of these is the replacement of petrochemical polyols with compounds obtained from renewable sources. It is common in biomass liquefaction to use sulfuric acid (VI) as a catalyst. The purpose of the present study was to test the effectiveness of a heterogeneous catalyst such as Nafion ion-exchange resin on the cellulose liquefaction process. The results obtained were compared with the bio-polyols obtained in a conventional way, using a homogeneous catalyst (sulfuric acid (VI)). Depending on the catalyst used and the temperature of the process, bio-polyols characterized, among other things, by a hydroxyl number in the range of 740–400 mgKOH/g were obtained. The research provides new information on the possibility of using heterogeneous catalysts in cellulose liquefaction. [ABSTRACT FROM AUTHOR]

A fundamental issue of waste management and the rail transport industry is the problem of utilizing used railroad ties. Wooden railroad ties are treated with a preservative, usually creosote. Due to their high toxicity, railroad ties are considered hazardous waste and must be utilized under various directives. It is proposed to utilize the troublesome waste by using the pyrolysis and torrefaction process. The research proves that the thermal method is effective for disposing of this type of waste. Torrefaction up to 250 °C gives high efficiency of impregnation removal, while pyrolysis up to 400 °C completely neutralizes waste. A series of experiments were conducted for various final pyrolysis temperatures to determine a minimum temperature for which the obtained solid products are free from creosote. Extraction with the use of the Soxhlet technique was performed for the raw materials and the obtained solid products—chars. The oil content for liquid fraction was also examined for each sample. As a result of the thermal treatment of the waste, fuel with combustion parameters better than wood was obtained. For a high final temperature of the process, the calorific value of char is close to that of hard coal. [ABSTRACT FROM AUTHOR]

The tanning industry generates significant amounts of solid waste and post-production wastewater, which should be managed in accordance with the principles of the circular economy. Waste is generated at various technological stages of production. This comprises mainly solid waste and leachate. A comprehensive solution to the problem of disposal of this waste is very important from economic and environmental points of view. This work presents research for a technological production line designed for the comprehensive processing of post-production residues. In the present paper, the authors present an analysis related to the possibility of processing leather flesh side (mizdra) as a substrate for methane fermentation. The study showed an increased biogas production from solid waste after enzymatic hydrolysis up to 248 Nm3/Mg. Preliminary research on the system designed for pre-treatment of sewage from the technological line is also presented. The study showed a COD reduction of more than 30%. The possibility of energy management of the solid fraction directly from the processes carried out is demonstrated. [ABSTRACT FROM AUTHOR]

The thermal pyrolysis of agriculture biomass has been studied in a fixed-bed reactor, where the pyrolysis was conducted at a steady temperature of 800 °C. This work analyses the pyrolysis products of six agricultural wastes: pistachio husks, walnut husks, sunflower hulls, buckwheat husks, corncobs and coconut shells. The conducted research compared examples of large waste biomass streams from different parts of the world as a potential source of renewable energy. Additionally, the kinetics of the reaction with the activation energy were analyzed and calculated for all raw materials in pyrolysis process. Biochars are characterised by higher combustion heat in comparison to the raw material samples. The average value of the heat of combustion increased due to pyrolysis process from 10 MJ/kg, with minimal value of 2.7 MJ/kg (corncob) and maximum of 13.0 MJ/kg for coconut, which is also characterised by the maximal absolute combustion heating value (32.3 MJ/kg). The increase in calorific values varied from 15% to 172% (with 54% reference for wood chips), which indicates that charring is an effective method for increasing the energy concentration. The obtained biochar were compared with wood chips, which are widely used solid fuel of organic origin. The studied biomass-derived fuels are characterised by lower ash contribution than wood. An analogous observation was made for the obtained biochars, whose ash contribution was lower than for the chips in terms of both unit-mass and unit-combustion-heat. The main advantage of this method is the production of solid fuel from biomass, which increases the calorific value and bulk density of biochar in comparison to raw material. [ABSTRACT FROM AUTHOR]

The routine pruning and cutting of fruit trees provides a considerable amount of biowaste each year. This lignocellulosic biomass, mainly in the form of branches, trunks, rootstocks, and leaves, is a potential high-quality fuel, yet often is treated as waste. The results of a feasibility study on biochar production by pyrolysis of residues from orchard pruning were presented. Three types of biomass waste were selected as raw materials and were obtained from the most common fruit trees in Poland: apple (AP), pear (PR), and plum (PL) tree prunings. Two heating rates and three final pyrolysis temperatures were applied. For the slow (SP) and fast pyrolysis (FP) processes, the heating rates were 15 °C/min and 100 °C/min, respectively. The samples were heated from 25 °C up to 400, 500, and 600 °C. Chemical analyses of the raw materials were conducted, and the pyrolysis product yields were determined. A significant rise of higher heating value (HHV) was observed for the solid pyrolysis products, from approximately 23.45 MJ/kg for raw materials up to approximately 29.52 MJ/kg for pyrolysis products at 400 °C, and 30.53 MJ/kg for pyrolysis products at 600 °C. Higher carbon content was observed for materials obtained by fast pyrolysis conducted at higher temperatures. [ABSTRACT FROM AUTHOR]

In this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume, area, shape and orientation on appearance density and thermal insulation properties of polyurethane foams was determined. The results presented in the paper confirm that microcomputed tomography is a useful tool for relatively quick estimation of polyurethane foams' microstructure, what is crucial especially in the case of thermal insulation materials. [ABSTRACT FROM AUTHOR]

In this work, we present the preparation and characterization of biomass-derived activated carbon (AC) in view of its application as electrode material for electrochemical capacitors. Porous carbons are prepared by pyrolysis of chestnut seeds and subsequent activation of the obtained biochar. We investigate here two activation methods, namely, physical by CO2 and chemical using KOH. Morphology, structure and specific surface area (SSA) of synthesized activated carbons are investigated by Brunauer-Emmett-Teller (BET) technique and scanning electron microscopy (SEM). Electrochemical studies show a clear dependence between the activation method (influencing porosity and SSA of AC) and electric capacitance values as well as rate capability of investigated electrodes. It is shown that well-developed porosity and high surface area, achieved by the chemical activation process, result in outstanding electrochemical performance of the chestnut-derived porous carbons. [ABSTRACT FROM AUTHOR]

Tires, conveyor belts, floor mats, and shoe soles form a main-stream of rubber waste. The amount of these used materials continuously increases due to development of the rubber market. Therefore, pro-ecological utilization (i.e., energy recycling instead of burning) and recovering valuable and recyclable materials becomes an urgent necessity. In this regard, this work was devoted to the chemical recycling of selected used rubber products, and it especially explores the possibility of limonene production. Different types of waste rubber were characterized and pyrolyzed at microgram and laboratory scales, and the results were compared. Additionally, the pyrolysis of tires, the most significant stream of rubber waste, was also conducted in a semi-technical scale reactor. The effectiveness of limonene formation in the liquid fractions obtained from different types of waste rubber was compared. [ABSTRACT FROM AUTHOR]

The aim of this study was to assess the possibility of using furniture waste for smokeless fuel production using the pyrolysis process. Four types of wood-based wastes were used in the pyrolysis process: pine sawdust (PS), chipboard (CB), medium-density fiberboard (MDF), and oriented strand board (OSB). Additionally, the slow and fast types of pyrolysis were compared, where the heating rates were 15 °C/min and 100 °C/min, respectively. Chemical analyses of the raw materials and the pyrolysis product yields are presented. A significant calorific value rise was observed for the solid pyrolysis products (from approximately 17.5 MJ/kg for raw materials up to approximately 29 MJ/kg for slow pyrolysis products and 31 MJ/kg for fast pyrolysis products). A higher carbon content of char was observed in raw materials (from approximately 48% for raw materials up to approximately 75% for slow pyrolysis products and approximately 82% for fast pyrolysis products) than after the pyrolysis process. This work presents the possibility of utilizing waste furniture material that is mostly composed of wood, but is not commonly used as a substrate for conversion into low-emission fuel. The results prove that the proposed solution produced char characterized by the appropriate properties to be classified as smokeless coal. [ABSTRACT FROM AUTHOR]

Pyrolysis of straw pellets and wood strips was performed in a fixed bed reactor. The chars, solid products of thermal degradation, were used as potential materials for activated carbon production. Chemical and physical activation processes were used to compare properties of the products. The chemical activation agent KOH was chosen and the physical activation was conducted with steam and carbon dioxide as oxidising gases. The effect of the activation process on the surface area, pore volume, structure and composition of the biochar was examined. The samples with the highest surface area (1349.6 and 1194.4 m2/g for straw and wood activated carbons, respectively) were obtained when the chemical activation with KOH solution was applied. The sample with the highest surface area was used as an adsorbent for model wastewater contamination removal. [ABSTRACT FROM AUTHOR]

This review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste tyres, a comprehensive evaluation was carried out to show the main effect of process conditions (heating rate, temperature, pressure, carrier gas flow rate, and type of volatile residence and process times) for different pyrolytic methods and types of apparatus on the yield of limonene. All the results cited are given in the context of the pyrolysis method and the type of reactor, as well as the experimental conditions in order to avoid contradictions between different researchers. It is shown that secondary and side reactions are very sensitive to interaction with the above-mentioned variables. The yields of all pyrolytic products are also given, as background for limonene, the main product reported in this study. [ABSTRACT FROM AUTHOR]

This article covers new application for char as a carrier of phase-change materials (PCM) that could be used as an additive to building materials. Being composed of bio-char and PCM, the granulate successfully competes with more expensive commercial materials of this type, such as Micronal® PCM. As a PCM carrier, char that was obtained from the pyrolysis of chestnut fruit (Aesculus hippocastanum) with different absorbances of the model phase-change material, Rubitherm RT22, was tested. DSC analysis elucidated several thermal properties (such as enthalpy, phase transition temperature, and temperature peak) of those mixtures and the results were compared with a commercial equivalent, Micronal DS 5040 X. Comparative research, approximating realistic conditions, were also performed by cooling and heating samples in a form of coatings that were made from chars with different content of RT22. These results indicated that the use of char as a PCM carrier was not only possible, but also beneficial from a thermodynamic point of view and it could serve as an alternative to commercial products. In this case, adsorption RT22 into char allowed for temperature stabilization comparable to Micronal DS 5040 X with ease of use as well as the economic advantages of being very low cost to produce due to microencapsulation. Other advantage of the proposed solution is related with the application of char obtained from waste biomass pyrolysis as a PCM carrier, and using this product in building construction to improve thermal comfort and increase energy efficiency. [ABSTRACT FROM AUTHOR]