Search

Amorphous and nanocrystalline alloys, as novel soft magnetic materials, can enable high efficiency in a wide range of power conversion techniques. Their wide application requires a thorough understanding of the fundamental material mechanisms, typical characteristics, device design, and applications. The first part of this review briefly overviews the development of amorphous and nanocrystalline alloys, including the structures of soft magnetic composites (SMCs), the key performance, and the underlying property-structure correction mechanisms. The second part discusses three kinds of high-power conversion applications of amorphous and nanocrystalline alloys, such as power electronics transformers (PETs), high-power inductors, and high-power electric motors. Further detailed analysis of these materials and applications are reviewed. Finally, some critical issues and future challenges for material tailoring, device design, and power conversion application are also highlighted. [ABSTRACT FROM AUTHOR]

With the increasing demand for safety and sustainable development in the power industry, the research on synthetic esters as a new type of insulating oil is becoming more and more important. This article takes pentaerythritol ester as the research object, simulates its fault conditions under partial discharge (low-energy discharge) and spark discharge (high-energy discharge), studies the dielectric and gas production characteristics, and explores the applicability of the existing fault diagnosis methods for synthetic esters. The results show that during partial discharge, the dielectric constant and loss of the synthetic ester increase, and the resistivity decreases. With the increase of discharge time, the relative percentage of CO continuously decreases, while that of C2H6 and C2H4 continuously increases. Since the C2H4 content of the synthetic ester is significantly higher than that of the mineral oil, the commonly used diagnostic methods are not suitable for the partial discharge fault diagnosis of the synthetic ester. In spark discharge, the gap distance has little impact on the starting voltage but a great impact on the breakdown time, and the dielectric performance deteriorates seriously. C2H2 is the characteristic gas of the synthetic ester spark discharge, and a large amount is produced, but with the increase of the gap distance, its relative percentage continuously decreases. For the spark discharge fault diagnosis of the synthetic ester, the improved three-ratio method and DUVAL triangle method have certain applicability. Comparing different discharge energies, the increase of the discharge energy aggravates the deterioration of the synthetic ester. Under high-energy discharge, the dielectric constant increases significantly, the hydrocarbons increase rapidly, and the C2H2 content increases sharply. Finally, the Duval triangle was modified according to the gas generation characteristics. This research can provide data support for the application and fault diagnosis of synthetic esters in power transformers. [ABSTRACT FROM AUTHOR]

Tactile sensing is currently a research hotspot in the fields of intelligent perception and robotics. The method of converting external stimuli into electrical signals for sensing is a very effective strategy. Herein, we proposed a self-powered, flexible, transparent tactile sensor integrating sliding and proximity sensing (SFTTS). The principle of electrostatic induction and contact electrification is used to achieve tactile response when external objects approach and slide. Experiments show that the material type, speed, and pressure of the perceived object can cause the changes of the electrical signal. In addition, fluorinated ethylene propylene (FEP) is used as the contact electrification layer, and indium tin oxide (ITO) is used as the electrostatic induction electrode to achieve transparency and flexibility of the entire device. By utilizing the transparency characteristics of this sensor to integrate with optical cameras, it is possible to achieve integrated perception of tactile and visual senses. This has great advantages for applications in the field of intelligent perception and is expected to be integrated with different types of optical sensors in the future to achieve multimodal intelligent perception and sensing technology, which will contribute to the intelligence and integration of robot sensing. [ABSTRACT FROM AUTHOR]

Reinjection is thought to be the most effective way to maintain reservoir pressure and production capacity for hydrothermal resources. The use of external water injection to replenish deep geothermal reservoirs is a new approach in China to addressing the problems of declining groundwater levels and energy depletion caused by the excessive and uneven exploitation of geothermal resources. However, the key challenge and focus of the feasibility assessment of this method lies in the chemical compatibility of the external water with the native geothermal reservoir water and surrounding rocks. In this paper, we discuss the geochemical response of a dolomite reservoir to lake water injection based on experiments on water–rock interaction in the Wumishan formation in the Dongli Lake area of Tianjin. The results show that after reactions with dolomite, the TDS of the reacted water decreases, indicating the occurrence of precipitation. According to the calculation results obtained using the PHQREEC program, the precipitation amount is found to be quite limited. Geochemical analysis indicates that at the initial stage of the reactions, plagioclase dissolves and releases alkaline metals like Ca-, Na-, SiO2- and Al-bearing compositions, leading to the oversaturation and precipitation of dolomite and calcite. As the reaction progresses, a portion of the dolomite dissolves, while the calcite continues to precipitate at a later stage. Illite precipitates and its effects on reservoir structure depend on its shape. Based on the experimental data, it can be concluded that the dolomite reservoir will be slightly affected by the reinjection of lake water; however, it is still a good method for the sustainable development of geothermal resources. [ABSTRACT FROM AUTHOR]

Drying involves the evaporation of moisture, accompanied by simultaneous heat transfer, mass transfer, and momentum transfer. While the diffusion law is considered an applicable model for explaining the drying phenomenon, the actual drying process cannot be accurately predicted using an analytical solution with a constant diffusion coefficient. Energy efficiency in the drying process is low due to an insufficient understanding of the mechanisms governing moisture migration from solids to air. The development of drying theory has stalled due to an unsolvable discrepancy between experimental results and analytical results. This study analyzes the effect of the binding energy of moisture in paddy rice on the diffusion coefficient. The theoretical relationship between water activity and drying rate in paddy rice was investigated, and the drying process was successfully explained by analyzing free energy transfer and transition theory. The mechanism of rice grain drying was described using a new theoretical solution for the drying process. These results provide new insights into the development of a scientific evaluation standard for assessing the efficiency of actual drying processes. [ABSTRACT FROM AUTHOR]

The Northern Jiangsu Basin (NJB), located at the northeast edge of the Yangtze block, is not only rich in oil and gas resources but also contains abundant geothermal resources. Nevertheless, the distribution of geothermal resources at medium depth in the NJB is still unclear due to its complex geological structure and tectonic–thermal evolution process, which restricts its exploitation and utilization. The characteristics of the geothermal field and distribution of geothermal reservoirs within the NJB are preliminarily analyzed based on available temperature measurements and geothermal exploration data. The prospective areas for the exploration of deep geothermal resources are discussed. The analysis results show that (1) Mesozoic–Paleozoic marine carbonate rocks are appropriate for use as principal geothermal reservoirs for the deep geothermal exploration and development within the NJB; (2) the geothermal field is evidently affected by the base fluctuation, and the high-temperature area is mainly concentrated at the junction of the Jianhu uplift and Dongtai depression; (3) the southeast margin of Jinhu sag, Lianbei sag, the east and west slope zone of Gaoyou sag, the low subuplifts within the depression such as Lingtangqiao–Liubao–Zheduo subuplifts, Xiaohai–Yuhua subuplifts and the west of Wubao low subuplift, have good prospects for deep geothermal exploration. [ABSTRACT FROM AUTHOR]

Water scarcity poses a significant challenge for people living in arid areas. Despite the effectiveness of many bioinspired surfaces in promoting vapor condensation, their water-harvesting efficiency is insufficient. This is often exacerbated by overheating, which decreases the performance in terms of the micro-droplet concentration and movement on surfaces. In this study, we used a spotted amphiphilic surface to enhance the surfaces' water-harvesting efficiency while maintaining their heat emissivity. Through hydrophilic particle screening and hydrophobic groove modifying, the coalescence and sliding characteristics of droplets on the amphiphilic surfaces were improved. The incorporation of boron nitride (BN) nanoparticles further enhanced the surfaces' ability to harvest energy from condensation. To evaluate the water-harvesting performance of these amphiphilic surfaces, we utilized a real-time recording water-harvesting platform to identify microscopic weight changes on the surfaces. Our findings indicated that the inclusion of glass particles in hydrophobic grooves, combined with 1.0 wt.% BN nanoparticles, enhanced the water-harvesting efficiency of the amphiphilic surfaces by more than 20%. [ABSTRACT FROM AUTHOR]

Electrical breakdown is an important physical phenomenon in power equipment and electronic devices. Recently, the mechanism of AC and DC breakdown has been preliminarily revealed as electrode–dielectric interface breakdown and bulk breakdown, respectively, based on space charge dynamics through numerical calculations. However, the AC breakdown mechanism still lacks enough direct experimental support, which restricts further understanding and the design and development of electrical structures. Here, in this study, LDPE films with various thicknesses ranging from 33 μm to 230 μm were surface modified with ozone for different durations to experimentally investigate DC and AC breakdown mechanism. The results indicate that carbonyl groups (C=O) were introduced onto the film surface, forming shallow surface traps and leading to a decreased average trap depth and an increased trap density. Such a surface oxidation modulated trap distribution led to enhanced space charge injection and bulk electrical field distortion, which decreased DC breakdown strength as the oxidation duration went longer, in all film thicknesses. However, such decreases in breakdown strength occurred only in films below 55 μm under AC stresses, as the enhanced electrical field distortion at the electrode–dielectric interface was more obvious and dominating in thin films. These experimental results further confirm the proposed electrode–dielectric interface breakdown of dielectric films and provide new understandings of space charge modulated electrical breakdown, which fulfills dielectric breakdown theory and benefits the miniaturization of power equipment and electronic devices. [ABSTRACT FROM AUTHOR]

Carbonate karst geothermal resources are widely distributed and have large reserves in North China. Currently, the scale of exploitation and utilization of the carbonate karst geothermal resources is gradually increasing. In this work, a geothermal exploitation area where the karst geothermal reservoirs are exploited on a large scale is selected as the study area, and methods including experiment and numerical simulation are used to study the exploitation-induced ground subsidence problems based on the long-term water level monitoring data of the geothermal reservoir. Through analyses of ground subsidence caused by water level changes in the geothermal reservoir, the following conclusions were obtained. The water level drawdown of different types of geothermal reservoirs had different effects on ground subsidence. The maximum ground subsidence of the study area caused by the water level decline of the Jxw carbonate geothermal reservoir was only 0.29 mm/a from 1983 to 2019, which is generally insignificant. In contrast, the same water level change of the Nm sandstone geothermal reservoir was predicted to cause 8.9 mm/a ground subsidence. To slow down or even prevent the ground subsidence, balanced production and reinjection are required. From the result of this work, it can be concluded that the decline of the water level of the Jxw carbonate geothermal reservoir caused by current large-scale geothermal exploitation will not cause serious ground subsidence. [ABSTRACT FROM AUTHOR]

The rheological behaviors of low-density polyethylene doped with additives (PEDA) determine the dynamic extrusion molding and structure of high-voltage cable insulation. However, the coupling effect of additives and molecular chain structure of LDPE on the rheological behaviors of PEDA is still unclear. Here, for the first time, the rheological behaviors of PEDA under uncross-linked conditions are revealed by experiment and simulation analysis, as well as rheology models. The rheology experiment and molecular simulation results indicate that additives can reduce the shear viscosity of PEDA, but the effect degree of different additives on rheological behaviors is determined by both chemical composition and topological structure. Combined with experiment analysis and the Doi–Edwards model, it demonstrates that the zero-shear viscosity is only determined by LDPE molecular chain structure. Nevertheless, different molecular chain structures of LDPE have different coupling effects with additives on the shear viscosity and non-Newtonian feature. Given this, the rheological behaviors of PEDA are predominant by the molecular chain structure of LDPE and are also affected by additives. This work can provide an important theoretical basis for the optimization and regulation of rheological behaviors of PEDA materials used for high-voltage cable insulation. [ABSTRACT FROM AUTHOR]

Distributed fiber optic sensors (DFOS) can detect structural cracks and structural deformation with high accuracy and wide measurement range. This study monitors the segmental prestressed bent cap, assembled with a large key dry joint, based on optical fiber technology, and it allows the comparison of its damaging process with that of a monolithic cast in place counterpart. The obtained results, comprising cross-section strain distributions, longitudinal strain profiles, neutral axis location, crack pattern, and the damage process, show that the DFOS technology can be successfully used to analyze the complex working stress state of the segmental beam with shear key joints, both in the elastic range and at the ultimate load, and to successfully identify the changing characteristics of the stress state of the segmental capping beam model when elastic beam theory no longer applies. The DFOS data confirm that the shear key joint, as the weak point of the segmental cap beam, results in the high stress concentration area, and the damage rate is higher than that of the cast-in-place beam. The accurate monitoring by the DFOS allows for the realization that the damage occurs at the premature formation of a concentrated compression zone on the upper part of the shear key. [ABSTRACT FROM AUTHOR]

During the operation of an enhanced geothermal system (EGS), the non-equilibrium temperature, pressure, and hydrochemistry caused by fluid injection intensify water–rock interactions, induce the mineral dissolution and precipitation in the reservoir near an injection well (also referred to as the near-well reservoir), and change reservoir permeability, thus affecting continuous and efficient geothermal exploitation. Based on the investigation of the M-1 injection well of the EGS in the Matouying uplift of Hebei Province, China, a THC reactive solute transport model using the TOUGHREACT program was established in this study to explore the mineral dissolution and precipitation laws of the near-well reservoir and their influencing mechanisms on the reservoir porosity and permeability in the long-term fluid injection of this well. As indicated by the results, the dissolution of primary feldspar and chlorite and the precipitation of secondary minerals (mainly dolomite and illite) occurred and water–rock interaction significantly reduced the porosity and permeability of the near-well reservoir in the long-term continuous injection process. Appropriate reduction in the injection flow rate, injection temperature, and the Mg2+ and K+ contents in the injected water can help inhibit the formation of secondary minerals and delay the plugging process of the near-well reservoir. [ABSTRACT FROM AUTHOR]

Nowadays, remote sensing datasets with long temporal coverage generally have a limited spatial resolution, most of the existing research uses the single image super-resolution (SISR) method to reconstruct high-resolution (HR) images. However, due to the lack of information in low-resolution (LR) images and the ill-posed nature of SISR, it is difficult to reconstruct the fine texture of HR images under large-scale magnification factors (e.g., four times). To address this problem, we propose a new reference-based super-resolution method called a Residual-Dense Hybrid Attention Network (R-DHAN), which uses the rich texture information in the reference image to make up for the deficiency of the original LR image. The proposed SR model employs Super-Resolution by Neural Texture Transfer (SRNTT) as a backbone. Based on this structure, we propose a dense hybrid attention block (DHAB) as a building block of R-DHAN. The DHAB fuses the input and its internal features of current block. While making full use of the feature information, it uses the interdependence between different channels and different spatial dimensions to model and obtains a strong representation ability. In addition, a hybrid channel-spatial attention mechanism is introduced to focus on important and useful regions to better reconstruct the final image. Experiments show that compared with SRNTT and some classical SR techniques, the proposed R-DHAN method performs well in quantitative evaluation and visual quality. [ABSTRACT FROM AUTHOR]

Gradually increasing power transmission voltage requires an improved high-voltage capability of polymeric insulating materials. Surface modification emerges as an easily accessible approach in enhancing breakdown and flashover performances due to the widely acknowledged modification of space-charge behaviors. However, as oxidation and fluorination essentially react within a limited depth of 2 μm underneath polymer surfaces, the nature of such bulk space-charge modulation remains a controversial issue, and further investigation is needed to realize enhancement of insulating performance. In this work, the surface oxidation-dependent space-charge accumulation in LDPE film was found to be dominated by an electrode/polymer interfacial barrier, but not by the generation of bulk charge traps. Through quantitative investigation of space-charge distributions along with induced electric field distortion, the functions of surface oxidation on the interfacial barrier of a typical dielectric polymer, LDPE, is discussed and linked to space-charge behaviors. As the mechanism of surface modification on space-charge behaviors is herein proposed, space-charge accumulation can be effectively modified by selecting an appropriate surface modification method, which consequentially benefits breakdown and flashover performances of polymeric insulating films for high-voltage applications. [ABSTRACT FROM AUTHOR]

Due to the complex operation conditions in a power transformer, an oil-impregnated pressboard (OIP) simultaneously suffers from thermal, electrical, and mechanical stress. Since most research studies have paid much attention to thermal or electrical aging of OIPs, this paper analyzes the effects of long-term mechanical vibrations on cellulose degradation in OIPs under simultaneous multi-stress. The aging experiments were firstly conducted at 130 °C, with a DC electric voltage of +6 kV, vibration amplitude of 10–50 μm, and vibration frequency of 100–300 Hz. The finite element analysis (FEA) of the pressboard vibration model was then performed on Abaqus to investigate the time–frequency domain characteristic parameters of compressive stress on the pressboard under varied vibration frequencies and amplitudes. The FEA results reveal that compressive stress on the pressboard in a multi-stress aging experiment coincided with the axial compressive stress on the insulation spacers in an SZ-50000/110 transformer. Moreover, combined with the degree of polymerization (DP) of cellulose, the effects of long-term vibration on cellulose degradation are reflected in two ways: the increase in compressive stress on the pressboard generates more links available for degradation, while more high frequency harmonic components in compressive stress accelerate the reaction rate in cellulose degradation. [ABSTRACT FROM AUTHOR]

Decomposition-based multi-objective evolutionary algorithms provide a good framework for static multi-objective optimization. Nevertheless, there are few studies on their use in dynamic optimization. To solve dynamic multi-objective optimization problems, this paper integrates the framework into dynamic multi-objective optimization and proposes a memory-enhanced dynamic multi-objective evolutionary algorithm based on L p decomposition (denoted by dMOEA/D- L p ). Specifically, dMOEA/D- L p decomposes a dynamic multi-objective optimization problem into a number of dynamic scalar optimization subproblems and coevolves them simultaneously, where the L p decomposition method is adopted for decomposition. Meanwhile, a subproblem-based bunchy memory scheme that stores good solutions from old environments and reuses them as necessary is designed to respond to environmental change. Experimental results verify the effectiveness of the L p decomposition method in dynamic multi-objective optimization. Moreover, the proposed dMOEA/D- L p achieves better performance than other popular memory-enhanced dynamic multi-objective optimization algorithms. [ABSTRACT FROM AUTHOR]

Despite the extensive research on nanocomposites, a fundamental theory on the interface region is still difficult to achieve. In the present paper, we chose epoxy resin and nano-SiO2, nano-SiC, nano-ZnO to prepare three kinds of nanocomposites. The dispersion characteristics at the terahertz range and dielectric permittivity at 1 Hz of epoxy resin-based nanocomposites were investigated. The reduction of the permittivity of nanocomposites at a slight filler concentration was absent at the terahertz range. The measurement results at 1 Hz show that the interaction between nano-SiO2, nano-SiC particles and epoxy resin was strong with the modification of the silane coupling agent. However, the modification of nano-ZnO particles was invalid. The Lorentz harmonic oscillator model was employed to fit the dispersion characteristics. The relevance between the damping constant and the dielectric permittivity at low frequency was established, indicating that the increase in the damping coefficient results from the restriction of the molecular chain motion by the interfacial region. The present results in this paper reveal a bright prospect of terahertz time-domain spectroscopy in establishing the theory of nanocomposite dielectric. [ABSTRACT FROM AUTHOR]

The substantial improvements in transmission voltage, which have been adopted to meet fast-growing energy demands, require more reliable power equipment and higher-quality insulating materials. The polytetrafluoroethylene (PTFE) nozzle, as the key part of a high-voltage circuit breaker, is often subjected to arc ablation and breakdown phenomena. Thus, it is very urgent to develop nozzles with better performance. In this study, PTFE/boron nitride (BN) composites were prepared. The relationships among the BN filler loading, thermal transition properties, spectral reflectance properties, arc ablation resistance, and AC dielectric breakdown performances, as well as their corresponding mechanisms, were studied. Experimental results show that the thermal conductivity and thermal diffusivity of PTFE/BN composites increased monotonously with BN loading, and that both parameters were improved by 41% and 44%, respectively, for 11 wt % composites compared with pure PTFE. Moreover, PTFE/BN composites had higher light reflectance in the wavelength range from 320 to 2500 nm. The PTFE/BN composites presented better arc ablation resistance performance with increased BN loading, which was improved by 88.5%. It is thought that the increased thermal conductivity, thermal diffusivity, the strong light reflectance, and surface sediment after arc ablation contribute to the improvement in arc ablation resistance performance. The AC breakdown strength of PTFE/BN composites was enhanced by 30.93%, attributed to the good heat dissipation properties introduced by the BN fillers. Thus, filling BN into the PTFE matrix would be helpful to solve the equipment issue that comes from the improvement in transmission voltage. [ABSTRACT FROM AUTHOR]

Power equipment operates under high voltages, inducing space charge accumulation on the surface of key insulating structures, which increases the risk of discharge/breakdown and the possibility of maintenance workers experiencing electric shock accidents. Hence, a visualized non-equipment space charge detection method is of great demand in the power industry. Typical electrochromic phenomenon is based on redox of the material, triggered by a voltage smaller than 5 V with a continuous current in μA~mA level, which is not applicable to high electric fields above 106 V/m with pA~nA operation current in power equipment. Until now, no naked-eye observation technique has been realized for space charge detection to ensure the operation of power systems as well as the safety of maintenance workers. In this work, a viologen/poly(vinylidene fluoride-co-hexafluoropropylene)(P(VDF–HFP)) composite is investigated from gel to insulating bulk configurations to achieve high-voltage electrical-insulating electrochromism. The results show that viologen/P(VDF–HFP) composite bulk can withstand high electric fields at the 107 V/m level, and its electrochromism is triggered by space charges. This electrochromism phenomenon can be visually extended by increasing viologen content towards 5 wt.% and shows a positive response to voltage amplitude and application duration. As viologen/P(VDF–HFP) composite bulk exhibits a typical electrical insulating performance, it could be attached to the surface of insulating structures or clamped between metal and insulating materials as a space charge accumulation indicator in high-voltage power equipment. [ABSTRACT FROM AUTHOR]

To date, breakdown voltage is an underlying risk to the epoxy-based electrical high voltage (HV) equipment. To improve the breakdown strength of epoxy resin and to explore the formation of charge traps, in this study, two types of polyhedral oligomeric silsesquioxane (POSS) fillers are doped into epoxy resin. The breakdown voltage test is performed to investigate the breakdown strength of neat epoxy and epoxy/POSS composites. Electron traps that play an important role in breakdown strength are characterized by thermally stimulated depolarized current (TSDC) measurement. A quantum chemical calculation tool identifies the source of traps. It is found that adding octa-glycidyl POSS (OG-POSS) to epoxy enhances the breakdown strength than that of neat epoxy and epoxycyclohexyl POSS (ECH-POSS) incorporated epoxy. Moreover, side groups of OG-POSS possess higher electron affinity (EA) and large electronegativity that introduces deep-level traps into epoxy resin and restrain the electron transport. In this work, the origin of traps has been investigated by the simulation method. It is revealed that the functional properties of POSS side group can tailor an extensive network of deep traps in the interfacial region with epoxy and enhance the breakdown strength of the epoxy/POSS nanocomposite. [ABSTRACT FROM AUTHOR]

Insulation fails quickly under high-frequency AC high voltage, especially bipolar square-wave voltage with a high dV/dt. It is of great significance to study the failure mechanism of epoxy casting insulation under such kind of voltage. In this paper, pin-plane epoxy casting insulation samples with air gaps were prepared, and the relation between the electrical trees under the high frequency bipolar square-wave voltage and the air gap conditions and voltage frequencies (1~20 kHz) were studied. Results indicated that, with the presence of air gaps, the electrical trees were bush-type and had a relatively slow growth rate, which was different from the fast-growing branch-type trees in the samples without air gap. The electrical tree characteristics related with the size of air gap and voltage frequency were also studied. The electrical tree grew faster under higher voltage frequency or with a smaller air gap. Results proved that discharge introduced a lot of defects for the surface layer of the epoxy resin samples and hence induced the possibility of multi-directional expansion of electrical trees. In addition, the resulting heat accumulation and unique charge transport synergistically affected the electrical tree characteristics under the high frequency bipolar square-wave voltage. [ABSTRACT FROM AUTHOR]

The decrease in electrical properties caused by the toughening of polypropylene (PP) is a difficult problem for the modification of PP used for cable insulation. In this research, an isotactic PP, a cross-linked polyethylene (XLPE) and two impact PP copolymers (IPCs) with an ethylene–propylene rubber phase content of 15 and 30% were prepared to assess the possibility of IPCs to be used as cable insulating material. The tensile properties and breakdown strength were evaluated, meanwhile, the rubber phase content dependence of the crystalline structure, morphology and trap distribution were also investigated. Results show that IPCs with a 15% rubber phase content (IPC15) can achieve the simultaneous improvement of elongation at break and breakdown strength compared with isotactic PP, which can be attributed to the special crystalline structure. According to the results of differential scanning calorimetry (DSC) and FTIR, it is proposed that the lamella thickness of IPC15 is maximal and some ethylene segments exist in PP crystals of IPC15 as crystalline structure defects, which is responsible for this enhanced breakdown strength. The morphology results reveal that rubber microspheres are found to coexist with spherulites, which can promote the relative sliding among lamellas under external force and further results in the increase in the elongation at break. [ABSTRACT FROM AUTHOR]

In order to satisfy demands of cable insulation for nuclear power, a low-smoke, halogen-free flame retardant and better cryogenic property insulation was prepared. The effect of thermal-oxidative aging on the dielectric properties was researched in this paper. The changes of chemical structure and thermal-oxidative stability caused by aging were characterized by Fourier transform infrared spectroscopy and a differential scanning calorimeter. The results showed that, the oxidative-induced stability reduced as complex products accumulated during aging. The dielectric properties including polarity, conductivity and breakdown at different aging stages were measured. For comparison, tensile testing was performed. The parameters related to conductivity changed notably, and were comparable with the changes in mechanical properties. [ABSTRACT FROM AUTHOR]

Thermal ageing of cross-linked polyethylene (XLPE) cable insulation is an important issue threatening the safe operation of power cables. In this paper, thermal ageing of XLPE was carried out at 160 °C in air for 240 h. The influence of oxygen diffusion on thermal ageing of XLPE was investigated by Ultraviolet–visible spectrophotometer (UV–Vis), tensile testing, and Fourier transformed infrared spectroscopy (FTIR). It was observed that the degradation degree not only depended on ageing time but also on sample positions. The thermally aged samples were more oxidized in the surface region, presented a darker color, more carbon atoms appeared in the conjugate cluster, had smaller elongation at break and tensile strength, and a larger carbonyl index. As ageing time increased, the non-uniform oxidation of the XLPE samples became more prominent. The degree of non-uniform oxidation caused by oxygen diffusion was quantitatively studied by first order oxidation kinetic. The calculated results demonstrated that carbonyl index measured by FTIR was more sensitive to non-uniform oxidation with a shape parameter in the range of 1–2. The result shown in this paper is helpful for interpreting and predicting the non-uniform ageing behavior of high voltage XLPE cables. [ABSTRACT FROM AUTHOR]

Epoxy resin-based nanocomposites have been widely researched for being potential insulating materials in high voltage power equipment. In this paper, nano-TiO2 particles were chosen and surface-modified by a silane coupling agent containing an epoxy group. The effect of functionalized nano-TiO2 doping on the physical properties of epoxy resin was studied. The results of differential scanning calorimetry show that Tg increased significantly and can be increased by up to 35 °C. Therefore, it is believed that the suppression of molecular motion by the addition of nanofillers works effectively in the case of this functionalized nano-TiO2 and a strong interaction between the epoxy resin and the nano-TiO2 was formed after surface modification. Consequently, dynamic mechanical properties, thermal conductivity, electrical conductivity, and trap characteristics of epoxy resin are all adjusted after introducing functionalized nano-TiO2. All of these physical properties were analyzed from the perspective of suppression of molecular motion, and it is of significance to establish the theory of a nanocomposite dielectric. Besides, the results show that the epoxy/TiO2 nanocomposite is expected to be applied in the insulation system of electrical equipment. [ABSTRACT FROM AUTHOR]

Dielectric breakdown is a significant property for the insulation system in high voltage power equipment. This paper is dedicated to the improvement of dielectric breakdown by surface-functionalized nanoparticles in low-density polyethylene (LDPE). Prior to the preparation of LDPE/TiO2 nanocomposites, the nanoparticles were surface modified by the silane coupling followed by the chemical reaction process. Results of Fourier transform infrared spectroscopy (FTIR) indicated that some polar groups and chemical bonding were introduced on the surface of TiO2 nanoparticles. A reduction of dielectric permittivity was observed at low nanoparticle loading (<2 wt%) samples, which responded to the restriction of the molecular chain in the interface region. High nanoparticle loadings (2 wt%, 5 wt%, 10 wt%) introduced an obvious relaxation polarization. The trap parameters detected by the thermally stimulated current (TSC) method indicated that the deep traps were introduced by small amounts of nanoparticles (≤2 wt%), while more shallow traps occurred in high loading (5 wt%, 10 wt%) samples. Meanwhile, the increase of breakdown strength at low loading samples were closely related to the deep traps, which was ascribed to the interface region by surface chemical modification. [ABSTRACT FROM AUTHOR]

Nano-dielectrics are sensitive to humidity and easily degraded in damp environment because of the high surface energy of nanoparticles. In order to study the effect of humidity on the dielectric properties of nano-dielectric, polypropylene (PP) was modified by polyolefin elastomer (POE) and nano-SiO2, and the samples with obvious filling concentration were pre-selected by breakdown strength for damp aging. The aging experiments were carried out in different relative humidity. The dielectric properties of new, hygroscopic saturation and samples after drying were measured and analyzed. It is found that the breakdown strength of hygroscopic saturation nano-dielectrics decreased obviously compared with new samples, and it was difficult to recover after drying. The damp degradation resulted in different changing trends of permittivity of PP and nano-dielectric, but there were relaxation loss peaks of water in both of them. The influence of damp degradation on the trap distribution was studied by thermally stimulated depolarization currents (TSDC), and it was found that the traps level introduced by water molecules was different in PP and nano-dielectrics. All experiment results showed that the performance of nano-dielectrics degraded obviously in humid environment, and it was difficult to recover even after complete drying because of the existence of bounded water molecules in nano-dielectrics. [ABSTRACT FROM AUTHOR]

Temperature is one of the key factors affecting space charge accumulation in high voltage direct current (HVDC) cable insulation material. The influence of temperature on charge accumulation in low density polyethylene (LDPE) has been investigated with a combined thermally stimulated depolarization current (TSDC) method and pulsed electro-acoustic (PEA) method. The experimental results indicate that there exists a transition temperature region of charge accumulation around 50 °C. The total accumulated charges all firstly increase and then decrease with the increasing polarization temperature under three typical polarization electric fields, and they have more accumulated charges in LDPE around 50 °C. The phenomenon has a close link with the dynamic processes of charge trapping and de-trapping, which were verified by TSDC results. At room temperature, the trapped charges are difficult to release from the traps, and these homocharges near the cathode can depress the further injection of the charges. More charges can be injected from the electrodes with the increase of temperature, while the charge migration is relatively lower before 50 °C, leading to more accumulated charges. When the temperature exceeds around 50 °C, the molecular movement is accelerated which can enhance the hopping probability of charges between the adjacent traps, resulting in few accumulated charges. [ABSTRACT FROM AUTHOR]

Piezoelectric ceramics is a functional material that can convert mechanical energy into electrical energy and vice versa. It can find wide applications ranging from our daily life to high-end techniques and dominates a billion-dollar market. For half a century, the working horse of the field has been the polycrystalline PbZr1−xTixO3 (PZT), which is now globally resisted for containing the toxic element lead. In 2009, our group discovered a non-Pb piezoelectric material, (BaCa)(ZrTi)O3 ceramics (BZT-BCT), which exhibits an ultrahigh piezoelectric coefficient d33 of 560–620 pC/N. This result brought extensive interest in the research field and important consequences for the piezoelectric industry that has relied on PZT. In the present paper, we review the recent progress, both experimental and theoretical, in the BZT-BCT ceramics. [ABSTRACT FROM AUTHOR]

Dielectric energy storage capacitors have advantages such as ultra-high power density, extremely fast charge and discharge speed, long service lifespan and are significant for pulsed power system, smart power grid, and power electronics. Polypropylene (PP) is one of the most widely used dielectric materials for dielectric energy storage capacitors. It is of interest to investigate how to improve its electrical breakdown strength by nanodoping and the influencing mechanism of nanodoping on the electrical breakdown properties of polymer nanocomposites. PP/Al2O3 nanocomposite dielectric materials with various weight fraction of nanoparticles are fabricated by melt-blending and hot-pressing methods. Thermally stimulated current, surface potential decay, and dc electrical breakdown experiments show that deep trap properties and associated molecular chain motion are changed by incorporating nanofillers into polymer matrix, resulting in the variations in conductivity and dc electrical breakdown field of nanocomposite dielectrics. Then, a charge transport and molecular displacement modulated electrical breakdown model is utilized to simulate the dc electrical breakdown behavior. It is found that isolated interfacial regions formed in nanocomposite dielectrics at relatively low loadings reduce the effective carrier mobility and strengthen the interaction between molecular chains, hindering the transport of charges and the displacement of molecular chains with occupied deep traps. Accordingly, the electrical breakdown strength is enhanced at relatively low loadings. Interfacial regions may overlap in nanocomposite dielectrics at relatively high loadings so that the effective carrier mobility decreases and the interaction between molecular chains may be weakened. Consequently, the molecular motion is accelerated by electric force, leading to the decrease in electrical breakdown strength. The experiments and simulations reveals that the influence of nanodoping on dc electrical breakdown properties may origin from the changes in the charge transport and molecular displacement characteristics caused by interfacial regions in nanocomposite dielectrics. [ABSTRACT FROM AUTHOR]

Polyimide has excellent electrical, thermal, and mechanical properties and is widely used as a dielectric material in electrical equipment and electronic devices. However, the influencing mechanism of sample thickness on electrical breakdown of polyimide has not been very clear until now. The direct current (DC) electrical breakdown properties of polyimide as a function of thickness were investigated by experiments and simulations of space charge modulated electrical breakdown (SCEB) model and charge transport and molecular displacement modulated (CTMD) model. The experimental results show that the electrical breakdown field decreases with an increase in the sample thickness in the form of an inverse power function, and the inverse power index is 0.324. Trap properties and carrier mobility were also measured for the simulations. Both the simulation results obtained by the SCEB model and the CTMD model have the inverse power forms of breakdown field as a function of thickness with the power indexes of 0.030 and 0.339. The outputs of the CTMD model were closer to the experiments. This indicates that the displacement of a molecular chain with occupied deep traps enlarging the free volume might be a main factor causing the DC electrical breakdown field of polyimide varying with sample thickness. [ABSTRACT FROM AUTHOR]

Polypropylene (PP) contains promising application prospects in thermoplastic cables for high voltage direct current (HVDC) power transmission because of its outstanding thermal and dielectric properties. However, the problem of poor toughness and space charge has restricted the application of pure PP in HVDC cables. In this paper, polyolefin elastomer (POE) and nano-silica were blended thoroughly and added into a PP mixture by a melting method. Scanning electron microscopy (SEM) was employed to observe the dispersion of POE and nanoparticles. Thermal properties were characterized by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Mechanical properties were evaluated by tensile tests. The elastomeric properties of composites were improved as the dispersed POE could transfer and homogenize external mechanical forces. DC breakdown results showed that the fail strength of composite with 10 phr POE and 1 phr nano-silica was obviously enhanced. The pulsed electro-acoustic (PEA) results showed that the injection and accumulation of space charge was increased by the introduction of POE, while it was restrained by the collective effect caused by nano-silica filling. X-ray diffraction (XRD) spectrograms showed that secondary ordered structures existed in the composites of PP, POE, and nano-silica, and that the ordered structure around the nanoparticles contributed to the enhancement of breakdown strength. The mechanical and dielectric properties were modified synergistically, which made the modified PP a propitious insulation material for HVDC cables. [ABSTRACT FROM AUTHOR]

Silicone rubber (SiR) is used as an insulating material for cables installed in a nuclear power plant. Gamma rays irradiated SiR sheets for various periods at temperatures of 145 and 185 °C, and the resultant changes were analyzed by examining complex permittivity spectra and surface potential decay characteristics. Three different processes, namely, instantaneous polarization, electrode polarization due to the accumulation of ions to form double charge layers at dielectric/electrode interfaces, and DC conduction caused by directional hopping of ions, contribute to the complex permittivity. By fitting the spectra to theoretical equations, we can obtain the dielectric constant at high frequencies, concentration and diffusion coefficient of ions and DC conductivity for the pristine and degraded samples. The instantaneous polarization becomes active with an increase of dose and ageing temperature. The thermal expansion coefficient estimated from the temperature dependence of dielectric constant at high frequencies becomes smaller with an increase in dose, which is in good agreement with the experimental results of the swelling ratio. Additionally, trap distributions are calculated from surface potential decay measurements and analyzed to explain the variation in conductivity. Trap energy increases firstly, and then decreases with an increase in dose, leading to a similar change in DC conductivity. It is concluded that generations of both oxidative products and mobile ions, as well as the occurrence of chain scission and crosslinking are simultaneously induced by gamma rays., Competing Interests: The authors declare no conflict of interest.