Search

Skeletal muscle myogenesis hinges on gene regulation, meticulously orchestrated by molecular mechanisms. While the roles of transcription factors and non-coding RNAs in myogenesis are widely known, the contribution of RNA-binding proteins (RBPs) has remained unclear until now. Therefore, to investigate the functions of post-transcriptional regulators in myogenesis and uncover new functional RBPs regulating myogenesis, we employed CRISPR high-throughput RBP-KO (RBP-wide knockout) library screening. Through this approach, we successfully identified Eef1a1 as a novel regulatory factor in myogenesis. Using CRISPR knockout (CRISPRko) and CRISPR interference (CRISPRi) technologies, we successfully established cellular models for both CRISPRko and CRISPRi. Our findings demonstrated that Eef1a1 plays a crucial role in promoting proliferation in C2C12 myoblasts. Through siRNA inhibition and overexpression methods, we further elucidated the involvement of Eef1a1 in promoting proliferation and suppressing differentiation processes. RIP (RNA immunoprecipitation), miRNA pull-down, and Dual-luciferase reporter assays confirmed that miR-133a-3p targets Eef1a1. Co-transfection experiments indicated that miR-133a-3p can rescue the effect of Eef1a1 on C2C12 myoblasts. In summary, our study utilized CRISPR library high-throughput screening to unveil a novel RBP, Eef1a1, involved in regulating myogenesis. Eef1a1 promotes the proliferation of myoblasts while inhibiting the differentiation process. Additionally, it acts as an antagonist to miR-133a-3p, thus modulating the process of myogenesis. [ABSTRACT FROM AUTHOR]

Alternative splicing (AS) is a crucial mechanism in post-transcriptional regulation, contributing significantly to the diversity of the transcriptome and proteome. In this study, we performed a comprehensive AS profile in nine tissues obtained from Duroc (lean-type) and Luchuan (obese-type) pigs. Notably, 94,990 AS events from 14,393 genes were identified. Among these AS events, it was observed that 80% belonged to the skipped exon (SE) type. Functional enrichment analysis showed that genes with more than ten AS events were closely associated with tissue-specific functions. Additionally, the analysis of overlap between differentially alternative splicing genes (DSGs) and differentially expressed genes (DEGs) revealed the highest number of overlapped genes in the heart and skeletal muscle. The novelty of our study is that it identified and validated three genes (PYGM, MAPK11 and CAMK2B) in the glucagon signaling pathway, and their alternative splicing differences were highly significant across two pig breeds. In conclusion, our study offers novel insights into the molecular regulation of diverse tissue physiologies and the phenotypic differences between obese- and lean-type pigs, which are helpful for pig breeding. [ABSTRACT FROM AUTHOR]

Rabies is a lethal encephalitis caused by the rabies virus (RABV) with a fatality rate near 100% after the onset of clinical symptoms in humans and animals. Microglia are resident immune cells in the central nervous system. Few studies have been conducted on the functional role of microglia in RABV infection. Here, we performed a transcriptomic analysis of mRNA expression profiles in the microglia of mouse brains intracerebrally infected with RABV. We successfully isolated single microglial cells from the mouse brains. The survival rate of dissociated microglial cells was 81.91%–96.7%, and the purity was 88.3%. Transcriptomic analysis revealed 22,079 differentially expressed mRNAs identified in the microglia of mouse brains infected with RABV strains (rRC-HL, GX074, and CVS-24) of varying virulence at 4 and 7 days post-infection (dpi) compared to the control group. The numbers of DEGs versus the control at 4 and 7 dpi in mice infected with rRC-HL, GX074, and CVS-24 were 3622 and 4590, 265 and 4901, and 4079 and 6337. The GO enrichment analysis showed that response to stress, response to external stimulus, regulation of response to stimulus, and immune system process were abundant during RABV infection. The KEGG analysis indicated that the Tlr, Tnf, RIG-I, NOD, NF-κB, MAPK, and Jak-STAT signaling pathways were involved in RABV infection at both 4 and 7 dpi. However, some phagocytosis and cell signal transduction processes, such as endocytosis, p53, phospholipase D, and oxidative phosphorylation signaling pathways, were only expressed at 7 dpi. The involvement of the Tnf and Tlr signaling pathways prompted us to construct a protein–protein interaction (PPI) network of these pathways. The PPI revealed 8 DEGs, including Mmp9, Jun, Pik3r1, and Mapk12. Notably, Il-1b interacted with Tnf and Il-6 with combined scores of 0.973 and 0.981, respectively. RABV causes significant changes in mRNA expression profiles in the microglia in mice. 22,079 differentially expressed mRNAs were identified in the microglia of mice infected with RABV strains of varying virulence at 4 and 7 dpi. The DEGs were evaluated using GO, KEGG, and PPI network analysis. Many immune pathways were up-regulated in RABV-infected groups. The findings will help elucidate the microglial molecular mechanisms of cellular metabolism dysregulated by RABV and may provide important information for investigating RABV pathogenesis and therapeutic methods. [ABSTRACT FROM AUTHOR]

The densified MnZn ferrite ceramics were prepared using the cold sintering process under pressure, with an acetate ethanol solution used as the transient solvent. The effects of the transient solvent, the pressure and annealing temperature on the density, and the micromorphology and magnetic properties of the sintered MnZn ferrites were studied. The densified MnZn ferrite was obtained using the cold sintering process and its relative density reached up to 85.4%. The transient solvent and high pressure are essential to the cold sintering process for MnZn ferrite. The annealing treatment is indispensable in obtaining the sample with the higher density. The relative density was further increased to 97.2% for the sample annealed at 950 °C for 6 h. The increase in the annealing temperature reduces the power loss at high frequencies. [ABSTRACT FROM AUTHOR]

The major method used to reduce the magnetic loss of soft magnetic composites (SMCs) is to coat the magnetic powder with an insulating layer, but the permeability is usually sacrificed in the process. In order to achieve a better balance between low losses and high permeability, a novel photodecomposition method was used in this study to create a ZnO insulating layer. The effect of the concentration of diethyl zinc on the formation of a ZnO insulating film by photodecomposition was studied. The ZnO film was best formed with a diethyl zinc n-hexane solution at a concentration of around 0.40 mol/L. Combined with conventional coupling treatment processes, a thin and dense insulating layer was coated on the surface of iron powder in situ. Treating the iron powder before coating by photodecomposition led to a synergistic effect, significantly reduced core loss, and the effective permeability only decreased slightly. An iron-based soft magnetic composite with a loss value of 124 kW/m3 and an effective permeability of 107 was obtained at the frequency of 100 kHz and a magnetic field intensity of 20 mT. [ABSTRACT FROM AUTHOR]

Sm2Fe17N3 compounds, having excellent intrinsic magnetic properties, are prone to decomposition at high temperatures; thus, a low melting point metal binder is the key to prepare high performance bulk magnets at low temperatures. In this paper, a new low melting point alloy Ce72Cu28-xAlx was used as the binders, and high-performance Ce-based alloy bonding Sm2Fe17N3 magnets were realized by the hot-pressing method. The experimental results demonstrated that the content of Al in the Ce-based alloys had an important influence on the performance of the magnets. High performance Sm-Fe-N bonded magnets with remanence of 10.19 KGs and maximum magnetic energy product of 21.06 MGOe were achieved by using 5 wt.% Ce72Cu22Al6 alloy as a binder. At the same time, it was found that the Ce72Cu28-xAlx alloy has a lower density and better bonding effect than the common Zn binder. Its bonding magnets still have higher performance even with extremely high oxygen content. Therefore, Ce72Cu28-xAlx alloy with low melting point is a promising new rare earth-based alloy binder. If the oxygen content of the alloy powders could be reduced, higher performance Sm2Fe17N3 bonded magnets can be prepared. [ABSTRACT FROM AUTHOR]

Ceramic injection molding is a near-net shape-processing technique, producing ceramic components with low tooling costs and complex shapes. In this paper, ZrO2 ceramics with high loading content in the green part were prepared by powder modification using zirconate coupling agent, injection molding and sintering, which benefited decreasing the usage of binders and deformation of ceramics. The rheological characteristics of feedstocks, densities, microstructures and mechanical properties of green and sintered parts with the different coupling media and sintering temperatures were studied. The results showed that the addition of a zirconate coupling agent with ethanol medium obviously increased the flowability of feedstocks and benefited achieving the green parts with high powder loading (86.5 wt.%) and bending strength (12.9 MPa) and the final unbroken ceramics. In addition, the sintering temperatures from 1500–1575 °C had no significant effects on the density, hardness, and surface morphology of the ceramic samples. However, the bending strength increased and some large grains with transgranular fracture occurred on the fractural surface at the sintering temperature of 1575 °C. [ABSTRACT FROM AUTHOR]

Polyvinyl butyral (PVB) was used in the Al(OH)3/carbon black/ethanol slurries by the three-roll mixing to prepare AlN powder using the carbothermal reduction–nitridation (CRN) process in the experiments. The effects of PVB addition on the synthesis of AlN powder were studied by viscosity, tap density, XRD, SEM and TG measurements. The results showed that the PVB layer covering on the surface of Al(OH)3 particles reduced the viscosity of Al(OH)3/carbon/ethanol slurry and increased the dispersion homogeneity of Al(OH)3/carbon raw powder. The tap densities of the Al(OH)3/carbon mixtures after three-roll milling could be increased with the increase in PVB addition. In the CRN process, most of the PVB covering Al(OH)3 particles evaporated and supplied the passage for nitrogen removal to the particles. Based on the experimental data, the role of PVB on the mixing and CRN process was discussed. [ABSTRACT FROM AUTHOR]