Search

The software-assisted reliability assessment of power electronic converters is increasingly important due to its multi-domain nature and extensive parametric calculations. The rainflow counting algorithm is gaining popularity for its low relative error in device lifetime estimation. Nevertheless, the offline operation of the algorithm prevents most simulation software packages considering other parameters for the device under study, such as aging and the current state of health in the estimation, as it requires a complete loading profile to run recursive comparison. This also brings difficulties in realization in circuit simulators such as SPICE. To tackle the issue, an in-the-loop circuit-based rainflow counting algorithm is proposed in this paper, and applied to estimate the consumed lifetime of the MOSFET in a boost converter for illustration. Instantaneous electrical and thermal performances, and the accumulated stress of the device can be monitored. Not only does this assist in evaluating the state of health of a device, but also allows the possibility of integrating the aging into the lifetime evaluation. The method follows the four-point rainflow counting algorithms, which continuously compares three adjacent temperature fluctuations Δ T j to select full cycles for two rounds, and the remaining cycles are counted as half cycles. To validate the performance, a comparative analysis in terms of counting accuracy and simulation speed was performed alongside the proposed method, MATLAB® and also with a well-accepted half-cycle counting method. Reported results show that the proposed method has an improved counting accuracy compared to the half-cycle counting from 24% to 3.5% on average under different load stresses and length conditions. The accuracy can be effectively improved by a further 1.3–2% by adding an extra comparison round. [ABSTRACT FROM AUTHOR]

This paper presents a systematic topological study to derive all possible basic and non-isolated three-port converters (TPCs) using power flow diagrams. Unlike most reported TPCs with one bidirectional port, this paper considers up to two bidirectional ports and provides a comprehensive analytical tool. This tool acts as a framework for all power flow combinations, selection, and design. Some viable converter configurations have been identified and selected for further analysis. [ABSTRACT FROM AUTHOR]

The conventional online battery impedance measurement method works by perturbing the duty cycle of the DC-DC power converter and measuring the response of the battery voltage and current. This periodical duty cycle perturbation will continuously generate large voltage ripples at the output of power converters. These large ripples will not easily be removed due to the high amplitude and wide frequency range and would be a challenge to meet tight output regulation. To solve this problem, this paper presents a new online battery impedance measurement technique by inserting a small switched resistor circuit (SRC) into the converter. The first contribution of this work is that the perturbation source is moved from the main switch to the input-side of the converter, so the ripples are reduced. The analysis and experimental results of the proposed method show a reduction of 16-times compared with the conventional method. The second contribution tackles the possible change of the battery state of charge (SOC) during the online battery measurement process, which will inevitably influence the impedance measurement accuracy. In this proposed method, battery impedance at multiple frequencies can be measured simultaneously using only one perturbation to accelerate measurement speed and minimize possible SOC change. The experimental impedance results coincide with a high-accuracy laboratory battery impedance analyzer. [ABSTRACT FROM AUTHOR]

This paper presents the four-quadrant operation modes of bidirectional chargers for electric vehicles (EVs) framed in smart car parks. A cascaded model predictive control (MPC) scheme for the bidirectional two-stage off-board chargers is proposed. The controller is constructed in two stages. The model predictive direct power control for the grid side is applied to track the active/reactive power references. The model predictive direct current control is proposed to achieve constant current charging/discharging for the EV load side. With this MPC strategy, EV chargers are able to transmit the active and reactive powers between the EV batteries and the power grid. Apart from exchanging the active power, the vehicle-for-grid (V4G) mode is proposed, where the chargers are used to deliver the reactive power to support the grid, simultaneously combined with grid-to-vehicle or vehicle-to-grid operation modes. In the V4G mode, the EV battery functions as the static var compensator. According to the simulation results, the system can operate effectively in the full control regions of the active and reactive power (PQ) plane under the aforementioned operation modes. Fast dynamic response and great steady-state system performances can be verified through various simulation and experimental results. [ABSTRACT FROM AUTHOR]