Search

Undercutting anchors are structural elements used in construction and geotechnics to stabilize both structures and soils. Their main applications include stabilizing slopes and embankments, reinforcing foundations, and providing support during tunnel construction and other underground works. The authors propose the use of these anchors in rock mass detachment technology. This article presents a comprehensive analysis of the mechanism behind rock mass detachment using an undercutting anchor. Particular attention is given to the influence of parameters such as the fracture energy of the medium and the coefficient of friction between the medium and the anchor head on the detachment process of rock elements during anchor expansion in the drilled hole. Numerical FEM analysis was employed to model the effect of changes in the shape and size of failure cones under varying simulation conditions. The discussed problem is crucial for evaluating the effectiveness of this anchor design under non-standard conditions, particularly in the unconventional destruction of rock media.

Today, there are many diagnostic methods and advanced measurement techniques enabling the correct diagnosis and assessment of the type and degree of wear of cogwheels (gears, pumps, etc.). The present study presents an analysis of the surface defects of a cogwheel of an oil pump prototype (3PW-BPF-24). The test object operated for a certain number of hours under controlled operating and environmental parameters. The damage to the surface layer was caused by fatigue phenomena and previous thermo-chemical treatment. On the basis of the significant percentage share (~30%) of residual austenite in the volume of the diffusion layer, a hypothetical conclusion was drawn about the suboptimal parameters of the thermo-chemical treatment process (in relation to the chemical composition of the analyzed pinion). A large number of research studies indicate that the significant presence of residual austenite causes a decrease in tooth surface hardness, the initiation of brittle cracks, a sharp decrease in fatigue strength, an increase in brittleness and a tendency to develop surface layer cracks during operation. High-resolution 3D scans of randomly selected pitting defects were used in the detailed study of the present work. It was indicated that the analysis of the morphology of surface defects allowed some degree of verification of the quality of the heat/chemical treatment. The martensitic transformation of residual austenite under controlled (optimum) repeated heat treatment conditions could significantly improve the durability of the pinion (cogwheel). In the case analyzed, the preferred treatment was the low-temperature treatment. The paper concludes with detailed conclusions based on the microscopic and macroscopic investigations carried out.

Individual differences in the response to platelet-rich plasma (PRP) therapy can be observed among patients. The genetic background may be the cause of this variability. The current study focused on the impact of genetic variants on the effectiveness of PRP. The aim of the present study was to analyze the impact of single nucleotide polymorphisms (SNP) of the platelet-derived growth factor receptor alpha ( PDGFRA ) gene on the effectiveness of treating lateral elbow tendinopathy (LET) with PRP. The treatment's efficacy was analyzed over time (2, 4, 8, 12, 24, 52 and 104 weeks after the PRP injection) on 107 patients using patient-reported outcome measures (PROM) and achievement of a minimal clinically important difference (MCID). Four SNPs of the PDGFRA gene (rs7668190, rs6554164, rs869978 and rs1316926) were genotyped using the TaqMan assay method. Patients with the AA genotypes of the rs7668190 and the rs1316926 polymorphisms, as well as carriers of the T allele of rs6554164 showed greater effectiveness of PRP therapy than carriers of other genotypes. Moreover, the studied SNPs influenced the platelets' parameters both in whole blood and in PRP. These results showed that PDGFRA gene polymorphisms affect the effectiveness of PRP treatment. Genotyping the rs6554164 and the rs1316926 SNPs may be considered for use in individualized patient selection for PRP therapy.

Vascular endothelial growth factor (VEGF) is implicated in both the etiology of tendinopathy and its healing process. Polymorphic variants of the VEGFA gene exhibit varied expression, which can influence the phenotype and treatment effectiveness. The aim of the present study was to analyze the influence of VEGFA gene variants on the effectiveness of tennis elbow therapy using platelet-rich plasma (PRP), measured through common patient-reported outcome measures (PROMs). A cohort of 107 patients (132 elbows) with tennis elbow was prospectively analyzed, with a two-year follow-up (at weeks 2, 4, 8, 12, 24, 52, and 104 after PRP injection). PROMs values were compared between variants of five VEGFA gene polymorphisms (rs699947 A>C, rs2010963 C>G, rs1413711 C>T, rs3024998 C>T and rs3025021 C>T) at each follow-up point. Patients with genotypes GG (rs2010963) and CC (rs3024998) had better response to PRP therapy (significantly fewer symptoms and limitations in the upper limb compared to carriers of alleles C and T, respectively). Polymorphisms influenced also selected hematological parameters. VEGFA gene polymorphisms (rs2010963 and rs3024998) appear to be significant treatment modifiers for tendinopathy, and their genotyping may serve as an effective tool for personalized patient selection for PRP therapy.

The purpose of this study was to experimentally determine the abrasion wear properties of ausferritic ductile iron austempered at 250 °C in order to obtain cast iron of class EN-GJS-1400-1. It has been found that such a cast iron grade makes it possible to create structures for material conveyors used for short-distance transport purposes, required to perform in terms of abrasion resistance under extreme conditions. The wear tests addressed in the paper were conducted at a ring-on-ring type of test rig. The test samples were examined under the conditions of slide mating, where the main destructive process was surface microcutting via loose corundum grains. The mass loss of the examined samples was measured as a parameter characteristic of the wear. The volume loss values thus obtained were plotted as a function of initial hardness. Based on these results, it has been found that prolonged heat treatment (of more than 6 h) causes only an insignificant increase in the resistance to abrasive wear.

The advancement of biomedicine in a socioeconomically sustainable manner while achieving efficient patient-care is imperative to the health and well-being of society. Magnetic systems consisting of iron based nanosized components have gained prominence among researchers in a multitude of biomedical applications. This review focuses on recent trends in the areas of diagnostic imaging and drug delivery that have benefited from iron-incorporated nanosystems, especially in cancer treatment, diagnosis and wound care applications. Discussion on imaging will emphasise on developments in MRI technology and hyperthermia based diagnosis, while advanced material synthesis and targeted, triggered transport will be the focus for drug delivery. Insights onto the challenges in transforming these technologies into day-to-day applications will also be explored with perceptions onto potential for patient-centred healthcare.

This paper presents the idea and provides an analysis of the rock breakout mechanism utilizing an undercut/breakout anchor. The new design is a modification of a standard undercut anchor, which is commonly found in applications involving steel-to-concrete anchorage. Of particular concern was the effect of the rock breakout strength on the anchor-pullout-induced failure of the rock mass. A numerical analysis was employed to model the effect of the changes to the shape and size of the breakout cones under varying rock strength conditions as a result of modifying the anchor design and loading pattern. The problem in question is pivotal for the potential evaluation of the effectiveness of the said anchor design under the non-standard conditions of its utilization.