Search

This research presents a proposal for alkali-activated permeable concrete composites with the use of industrial by-products, including ground granulated blast-furnace slag (GGBS) and waste-foundry sand, as well as agro-desecrate product, i.e., sugarcane bagasse ash (SBA). GGBS and SBA served as binders, with crushed granite as coarse aggregate and waste-foundry sand as fine aggregate. The novelty of this proposal is in examining the influence of SBA, in combination with slag, on the fresh- and hardened-state properties of the proposed permeable concretes. Experiments were conducted to optimize the SBA percentage based on hydraulic conductivity and compressive and tensile strength after 28 days of air curing. The hardened density, compaction factor (workability), and saturated water absorption were also measured for all the mixes. Furthermore, the control and optimal mixes were subjected to evaluate the microstructure analysis (EDX, XRD, and FESEM) after 28 days of air curing. The mix containing 100% GGBS and 0% SBA served as the reference, with the optimal 10% SBA mix (with 90% GGBS) used for comparative analysis to understand its effect on the properties of permeable composites. The results showed positive or acceptable mechanical performance at a mix ratio of 10% SBA to 90% GGBS as binders. This study aims to enhance the understanding of the engineering behavior of alkali-activated permeable composites, facilitating the rational design of permeable pavement systems through the effective use of agro-industrial waste products, thereby conserving ecosystems while meeting engineering requirements. [ABSTRACT FROM AUTHOR]

This study investigated the purification of pollutants in runoff rainwater by constructing a micro-ecosystem using waste-activated sludge (WAS) and riverbed sludge (RBS) as inoculums in combination with pervious concrete. The research results showed that the best hydraulic retention time (HRT) was 9 h. The COD and ammonia nitrogen (NH4+-N) removal of the waste-activated sludge ecosystem (WASE) was 62.67% and 71.21%, respectively, while the riverbed sludge ecosystem (RBSE) showed COD and NH4+-N removal percentages of 46.05% and 66.55%, respectively. The analysis of the genetic metabolism of microbial genes showed that the system was microbially enhanced with extensive and diverse populations. At the phylum level, the microorganisms responsible for degrading organic matter were mainly Firmicutes and Actinobacteriota. At the genus level, the Trichococcus genus was dominant in the WASE, while the Dietzia, norank_f__Sporomusaceae and norank_f__norank_o__norank_c__BRH-c20a genera were the central bacterial populations in the RBSE. The proliferation of phylum-level bacteria in the WASE was relatively large, and the genus-level bacteria demonstrated a better removal efficiency for pollutants. The overall removal effect of the WASE was better than that of the RBSE. The application analyses showed that a WASE is capable of effectively accepting and treating all rainfall below rainstorm levels and at near-full rainstorm levels under optimal removal efficiency conditions. This study innovatively used wastewater plant waste-activated sludge combined with pervious concrete to construct a micro-ecosystem to remove runoff rainwater pollutants. The system achieved pollutant removal comparable to that of pervious concrete modified with adsorbent materials. An effective method for the collection and pollutant treatment of urban runoff rainwater is provided. [ABSTRACT FROM AUTHOR]

This study investigates the performance of sludge-added pervious concrete (SPC) at different curing temperatures by replacing some of the cement with activated sludge (AS). The results reveal that the incorporation of AS into pervious concrete had a favorable impact. At a curing temperature of 30 °C, the 28-day compressive strength and specific surface area reached 20.8 MPa and 9.14 m2/g, respectively, representing a 60% and 98.7% increase, in comparison to conventional concrete. Furthermore, the addition of AS to the concrete results in a notable reduction in the concentration of chemical oxygen demand (COD) in surface runoff water. The maximum rate of COD removal observed was 55.6%. A mechanism study revealed that the strength of concrete increased due to the reaction between reactive SiO2 in AS and CaO in the aggregate. At a temperature of 30 °C, the microorganisms in the activated sludge fermentation process exhibit a higher production rate of fermentation gas, resulting in a greater escape of gas and an increase in the number of micropores in the permeable concrete. This leads to an enhanced specific surface area, which in turn exhibits a superior adsorption effect on COD. [ABSTRACT FROM AUTHOR]

Pervious concrete, because of its high porosity, is a suitable material for reducing the effects of water precipitations and is primarily utilized in road pavements. In this study, the effects of binder-to-aggregate (B/A) ratios, as well as mineral admixtures with and without polypropylene fibers (PPFs) (0.2% by volume), including fly ash (FA) or silica fume (SF) (10% by substitution of cement), on the mechanical properties and durability of pervious concrete were experimentally observed. The experimental campaign included the following tests: permeability, porosity, compressive strength, splitting tensile strength, and flexural strength tests. The durability performance was evaluated by observing freeze–thaw cycles and abrasion resistance after 28 d curing. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermal analysis (TGA-DTA), and scanning electron microscopy (SEM) combined with energy dispersive spectroscopy (EDS) were employed to investigate the phase composition and microstructure. The results revealed that, for an assigned B/A ratio identified as optimal, the incorporation of mineral admixtures and fibers mutually compensated for their respective negative effects, resulting in the effective enhancement of both mechanical/microstructural characteristics and durability properties. In general, pervious concrete developed with fly ash or silica fume achieved higher compressive strength (>35 MPA) and permeability of 4 mm/s, whereas the binary combination of fly ash or silica fume with 0.2% PPFs yielded a flexural strength greater than 6 MPA and a permeability of 6 mm/s. Silica fume-based pervious concrete exhibited excellent performance in terms of freeze–thaw (F-T) cycling and abrasion resistance, followed by fiber-reinforced pervious concrete, except fly ash-based pervious concrete. Microstructural analysis showed that the inclusion of fly ash or silica fume reduced the harmful capillary pores and refined the pore enlargement caused by PPFs in the cement interface matrix through micro-filling and a pozzolanic reaction, leading to improved mechanical and durability characteristics of pervious concrete. [ABSTRACT FROM AUTHOR]

Pervious concrete is widely used as a paving material. Pervious pavement is generally constructed by pouring fresh pervious concrete and compacting. However, it has some difficulties such as finishing and curing. In addition, the road has to be closed, until the pervious concrete gains enough strength. Pervious concrete block is a new material that can overcome these difficulties. In this study, the effect of compression force on the strength and infiltration rate of pervious concrete blocks has been investigated. The compaction process was different from traditional methods in this study, and was applied according to predesignated compression forces on fresh pervious concrete mixtures sensitively. Within the scope of the study, 36 different mixtures were produced by applying four different compression forces (25, 50, 75, and 100 kN) in three different sample thicknesses (60, 80, and 100 mm) with three different aggregate sizes (2–4, 4–8, and 8–16 mm). As a result, it was found that while the increase in the compression force increases the splitting tensile strength of pervious concrete blocks with 2–4 and 4–8 mm aggregate, it causes a decrease in the strength due to the aggregate crushing phenomenon in mixtures with 8–16 mm aggregate, 6 cm thick samples. In this study, it was seen that the expectation that the increase in compaction would always cause an increase in strength is not valid, contrary to the literature. The infiltration rate decreased as the compression force increased, as expected. It was determined that the new infiltration rate measurement method has been found effective. Considering the strength requirement in the TS 2824 EN 1338 standard, pervious concrete blocks produced with 4–8 mm aggregate, compressed with 75 kN force and having 80 mm thickness have been determined as the optimum block type. [ABSTRACT FROM AUTHOR]

In recent years, various aspects of research related to pervious concrete (PC) have progressed rapidly, and it is necessary to summarise and generalise the latest research results. This paper reviews and compares the raw materials of pervious concrete, examining elements such as porosity, permeability, mechanical properties, and durability. According to comparisons, we put forward an ideal aggregate model with Uneven Surface, which may reinforce the mechanical properties. By summarising the important issues of aggregate, particle size, water–cement ratio, additives and admixtures, mixing ratio design, mixing and moulding, and other factors that affect porosity, new design methods are proposed. A new effective stress model of pervious concrete based on continuous porosity and Terzaghi effective stress is developed which may fit the effective stress principle better. Finally, by summarising the research frontiers of pervious concrete, key issues that need to be addressed in future scientific research on pervious concrete are raised. [ABSTRACT FROM AUTHOR]

Pervious concrete is desirable for water drainage in building systems, but achieving both high strength and good permeability can be challenging. Also, the importance of compaction energy is significant in determining the efficiency of pervious concrete. However, research on the development of unconfined compressive strength (UCS) prediction models for pervious concrete materials that incorporate compaction energy parameters remains unexplored. Therefore, this study aimed to balance strength and permeability while optimizing the compaction energy required for concrete production. A Central Composite Design (CCD) was used to design experiments within the response surface methodology (RSM) and evaluate the UCS, the porosity and permeability of pervious concrete specimens produced with varying cement content (280.00–340.00 kg/m3), the water-to-cement ratio (0.27–0.33), the aggregate-to-cement ratio (4:1–4.5:1), and compaction energy (represented by VeBe compaction time, 13–82 s). A regression model with goodness of fit (R2adjusted > 0.87) was calibrated to estimate the UCS of pervious concrete as a function of mix design parameters and VeBe compaction time (Tvc). This model can potentially guide field practices by recommending compaction strategies and mix designs for pervious concrete, achieving a desirable balance between mechanical strength and hydraulic permeability for building construction applications. [ABSTRACT FROM AUTHOR]

In the realm of sustainable construction materials, the quest for low-environmental-impact binders has gained momentum. Addressing the global demand for concrete, several alternatives have been proposed to mitigate the carbon footprint associated with traditional Portland cement production. Despite technological advancements, property inconsistencies and cost considerations, the wholesale replacement of Portland cement remains a challenge. This study investigates the feasibility of using alkali-activated slag (AAS)-based binders for two specific applications: structural plaster and pervious concrete. The research aims to develop an M10-grade AAS plaster with a 28-day compressive strength of at least 10 MPa for the retrofitting of masonry buildings. The plaster achieved suitable levels of workability and applicability by trowel as well as a 28-day compressive strength of 10.8 MPa, and the level shrinkage was reduced by up to 45% through the inclusion of shrinkage-reducing admixtures. Additionally, this study explores the use of tunnel muck as a recycled aggregate in AAS pervious concrete, achieving a compressive strength up to 20 MPa and a permeability rate from 500 to 3000 mm/min. The relationship between aggregate size and the physical and mechanical properties of no-fines concretes usually used for cement-based pervious concrete was also confirmed. Furthermore, the environmental impacts of these materials, including their global warming potential (GWP) and gross energy requirement (GER), are compared to those of conventional mortars and concretes. The findings highlight that AAS materials reduce the GWP from 50 to 75% and the GER by about 10–30% compared to their traditional counterparts. [ABSTRACT FROM AUTHOR]

The utilization of dredged sediment (DS) as a transformative material in building applications presents an ideal consumption strategy. This study endeavors to create a novel ceramsite lightweight aggregate (LWA) through the co-sintering of DS and rice husks (RHs), further integrating this LWA into the construction of pervious concrete. Results revealed that the optimum production procedure for the DS-based LWA incorporated a 21% RH addition, a sintering temperature of 1100 °C, and a sintering duration of 21 min. Notably, the optimal ceramsite LWA, denoted as SDC-H, exhibited a cylinder compressive strength of 28.02 MPa and an adsorption efficiency for Pb2+ of 94.33%. Comprehensive analysis (encompassing bulk density, cylinder compressive strength, water absorption, and the leaching concentrations of heavy metals) confirmed that SDC-H impacted the specification threshold of high-strength light aggregate derived from solid waste (T/CSTM 00548-2022). Substituting 50% of SDC-H led to a diminution in the mechanical properties but an improvement in the dynamic adsorption capacity of the innovative pervious concrete, registering a mechanical strength of 26.25 MPa and a cumulative adsorption capacity for Pb2+ of 285 mg/g. These performances of pervious concrete containing 50% SDC-H might correlate with the evolution of an interconnected and open-pore structure. [ABSTRACT FROM AUTHOR]

The response surface regression model of plant-growing ecological concrete is established based on the factors of the water–binder ratio, fly ash content, and design porosity, with 28-day compressive strength, connectivity porosity, and pH value as response variables. Based on optimizing the mix proportion with the regression model, different dosages of acetic acid are used as excitation agents to increase the compressive strength and reduce the alkalinity of plant-growing ecological concrete to enhance its service life and vegetation performance. The results show that the compressive strength of plant-growing ecological concrete with a water–binder ratio of 0.3, a fly ash content of 26%, and a design porosity of 22% was 10.32 MPa, the connectivity porosity was 20.00%, and the pH value was 11. After the addition of acetic acid at 0.4% of the mass of the cementitious material, the compressive strength increased by 40.29%, and the pH value decreased by 6.33%. This study proposes a cost-effective means and provides data support for the engineering application of plant-growing ecological concrete. [ABSTRACT FROM AUTHOR]

Pervious planting concrete (PPC) is in line with the concept of ecological environmental protection. However, due to its own porous structure, it is difficult to obtain excellent mechanical properties and water permeability at the same time, which hinders its promotion and application. In this paper, natural gravel (NG), ordinary Portland cement (OPC), polyvinyl alcohol latex powder (PVAP) and polycarboxylate superplasticizer (PS) were used to prepare the PPC, and its mechanical properties and water permeability were studied. Three kinds of plants were planted in the PPC and their planting properties were studied. At the same time, the effect of Bacillus on the planting properties was studied. The results show that when the water–binder ratio (W/B) was 0.28 and the PVAP content was 0.8%, both the mechanical properties and water permeability of the PPC were optimal. The compressive strength and permeability coefficient were 14.2 MPa and 14.48 mm/s, respectively. The mechanical properties and water permeability of PPC prepared with 10~20 mm NG were better than those prepared with 5~10 mm NG. Among the three plants, the germination rate and growth of Elymus dahuricus Turcz (EDT) were the best. The incorporation of Bacillus can optimize its planting properties and promote the effective combination between plants and the PPC substrate. [ABSTRACT FROM AUTHOR]

Urban runoff is acidic in nature and mainly consists of heavy metals and sediments. In this study, the pervious concrete samples were cured in a CO2-rich environment and their performance under runoff conditions was evaluated by passing different solutions containing clay particles, heavy metal ions, and acid species. The compressive strength of these samples was reduced by up to 14% when they were cured in water instead of a CO2 environment. Heavy metal ions, including lead and zinc, in the simulated runoff were adsorbed in these pervious concrete samples by up to 96% and 80% at the end of the experiment, but the acid species in this runoff could leach calcium ions from the cement components during passage. Clay particles in the runoff were trapped in the flow channels of samples, which marginally reduced the percolation rate by up to 14%. Concrete carbonation reduced the release of calcium ions under runoff conditions, and zinc removal was relatively lower because of the nonavailability of hydroxyl sites in the interconnected pore structure. The weight and strength losses in the carbonated concrete samples were relatively lower at the end of the acid storage experiment, suggesting that CO2 curing reduces cement degradation in aggressive chemicals. The SEM and tomography images revealed the degraded microstructure, while the XRD results provided data on the mineralogical changes. CO2 curing improves the strength gain and service life of pervious concrete in runoff environments. [ABSTRACT FROM AUTHOR]

Extensive use of cement in the construction industry increases CO2 emissions and has a negative impact on the environment. In this work, recycled coarse aggregate (RCA) from construction and demolition wastes (C&DW) was used to fabricate sustainable pervious concrete (PC). In order to mitigate the environmental hazards of excess cement waste and to improve the engineering properties of PC, silica fume (SF) and ground granulated blast-furnace slag (GGBS) were added. The effects of SF and GGBS on the compressive strength, permeability coefficient, porosity, and abrasion resistance of recycled aggregate pervious concrete (RAPC) were investigated. The results show that the incorporation of GGBS and SF effectively improves the compressive strength of RAPC but reduces the permeability coefficient and porosity. Moreover, due to the filling effect and pozzolanic activity, the incorporation of GGBS and SF significantly enhances the abrasion resistance of RAPC. Furthermore, the relationships between the compressive strength, permeability coefficient, porosity, and abrasion resistance of RAPC are clarified. The optimum replacement is achieved when the SF content is 7%, and the GGBS content is 20%, respectively, which results in the highest compressive strength (28.9 MPa) and the lowest permeability coefficient (1.2 mm/s) at 28 days, and the lowest mass loss rate (12.1%) after the Cantabro abrasion test. [ABSTRACT FROM AUTHOR]

In the exploration of sustainable construction materials, the application of ferronickel slag (FNS) in creating pervious concrete has been investigated, considering its potential to meet the dual requirements of mechanical strength and fluid permeability. To elucidate the statistical properties and models for predicting the performance of FNS-composited pervious concrete with different sizes of aggregates and mixtures, a series of experiments, including 54 kinds of mixtures and three kinds of aggregate, were conducted. The focus was on measuring the compressive strength and the permeability coefficient. The results indicate that the compressive strength of pervious concrete decreases with the increase in aggregate size, while the permeability coefficient increases with the increase in aggregate size. Through normalization, the variability of these properties was quantitatively analyzed, revealing coefficients of variation for the concrete's overall compressive strength and the permeability coefficient at 0.166, 0.132, and 0.150, respectively. Predictive models were developed using machine learning techniques, such as Linear Regression, Support Vector Machines, Regression Trees, and Gaussian Process Regression. These models demonstrated proficiency in forecasting the concrete's compressive strength and permeability coefficient. [ABSTRACT FROM AUTHOR]

It is unknown whether Ferronickel slag (FNS)-ordinary Portland cement (OPC)-based pervious concrete (FOPC) is feasible. To this end, a feasibility study was conducted on FOPC. Firstly, a detailed microscopic examination of the FNS powder was conducted, encompassing analyses of its particle size distribution, SEM, EDS, and chemical composition. These analyses aimed to establish the suitability of a composite of FNS and OPC as a composite cementitious material. Subsequent experimentation focused on evaluating the compressive strength of the composite paste material with varying mixed proportions, revealing a slight reduction in strength as the FNS substitution rate increased. Furthermore, the study designed eighteen different mix proportions of FOPC to investigate the key physical properties, including porosity, density, compressive strength, and the coefficient of permeability. Findings indicated that increases in the cementitious material proportion correlate with enhanced concrete strength, where the ratio of cementitious to aggregate increased by 6.7% and 16.5%, and the strength of FOPC increased by 10–13% and 30–50%, respectively. Conversely, a rise in the FNS substitution rate led to a reduction in compressive strength across different mix ratios. Additionally, the ratio of paste material to aggregate was found to significantly influence the permeability coefficient. These comprehensive performance evaluations suggest that incorporating FNS into OPC for pervious concrete applications is a feasible approach, offering valuable insights for the promotion of waste reuse and the advancement of energy conservation and emissions reduction efforts. [ABSTRACT FROM AUTHOR]

The impacts of various aggregate particle sizes and cement contents on the internal structure of pervious concrete were investigated. Accordingly, test blocks with different aggregate particle sizes and cement contents were dissected and photographed. Subsequently, the captured images were processed using the ImageJ software (1.53i) to analyze the profiles of the test blocks and identify the internal mesoscopic parameters of the pervious concrete. This study discusses the relationship between microscopic parameters and macroscopic factors based on experimental results. It also fits functional equations linking the permeability coefficient with pore parameters, matrix parameters, and compressive strength. The results indicated that, as the aggregate size increased, the internal pore diameter of the pervious concrete increased, whereas the total area and width of the cement matrix decreased. This resulted in a low permeability coefficient and high compressive strength of the test block. Increasing the cement content in pervious concrete reduced the porosity and increased the width and area of the internal matrix. Consequently, the permeability coefficient decreased, and the compressive strength of the test block increased. [ABSTRACT FROM AUTHOR]

Pervious concrete has great potential for use in many practical applications as a part of urban facilities that can add value through water harvesting and mitigating severe damage from floods. The construction and agricultural industries can take direct advantage of pervious concrete's characteristics when water is a key factor included in projects as part of the useful life of a facility. Pervious concrete also has applications in vertical constructions, fountains, and pedestrian crossings. This work evidences that pervious concrete's corrosion current increases with increasing aggregate size. Also, corrosion is a factor to consider only when steel pieces are immersed, aggravated by the presence of chlorine, but it drains water and does not retain moisture. Steel-reinforced pervious concrete was studied, and the grain size of the inert material and the corrosion process parameters were investigated. The electrochemical frequency modulation technique is proposed as a suitable test for a fast, reproducible assessment which, without damaging reinforced cement structures, particularly pervious concrete, indicates a trend of increasing corrosion current density as the size of the aggregate increases or density diminishes. [ABSTRACT FROM AUTHOR]

To overcome limitations inherent in existing mechanical performance prediction models for pervious concrete, including material constraints, limited applicability, and inadequate accuracy, this study employs a deep learning approach to construct a Convolutional Neural Network (CNN) model with three convolutional modules. The primary objective of the model is to precisely predict the 28-day compressive strength of pervious concrete. Eight input variables, encompassing coarse and fine aggregate content, water content, admixture content, cement content, fly ash content, and silica fume content, were selected for the model. The dataset utilized for both model training and testing consists of 111 sample sets. To ensure the model's coverage within the practical range of pervious concrete strength and to enhance its robustness in real-world applications, an additional 12 sets of experimental data were incorporated for training and testing. The research findings indicate that, in comparison to the conventional machine learning method of Backpropagation (BP) neural networks, the developed CNN prediction model in this paper demonstrates a higher coefficient of determination, reaching 0.938, on the test dataset. The mean absolute percentage error is 9.13%, signifying that the proposed prediction model exhibits notable accuracy and universality in predicting the 28-day compressive strength of pervious concrete, regardless of the materials used in its preparation. [ABSTRACT FROM AUTHOR]

In order to overcome the limitations of traditional pervious concrete, which is difficult to balance in terms of both mechanical properties and permeability, this study proposed a novel and effective approach to improve the performances of pervious concrete (PC) based on hexagonal boron nitride (h-BN) and basalt fibers (BF). The mechanical properties and permeability tests of PC with single-doped or double-doped h-BN and BF were conducted first. Then the influence laws of h-BN and BF content on the compressive strength, flexural strength, porosity, and permeability coefficient for PC were revealed. Finally, the micro-mechanism effects of h-BN and BF on the performances of PC were explored by using a scanning electron microscope and an energy dispersive spectrometer. The results showed that the compressive strength of PC was increased with the increase in the h-BN content, and the flexural strength, porosity, and permeability coefficient increased first and then decreased. Meanwhile, with the increase in the BF content, the compressive strength and flexural strength of PC increased first and then decreased. Moreover, the compressive strength, flexural strength, porosity, and permeability coefficient of the proposed pervious concrete were 22.8 MPa, 5.17 MPa, 18.5%, and 5.09 mm/s, respectively, which were increases of 21.9%, 19.7%, 60.9%, and 42.2%, respectively, compared with ordinary permeable concrete when the optimal admixture combination was 15% fly ash, 0.08% h-BN, and 2.25% BF. This study can avoid the limitations of traditional pervious concrete and provide an efficient alternative way for improving the mechanical and permeability properties of pervious concrete. [ABSTRACT FROM AUTHOR]

Pervious concrete is an innovative eco-friendly construction material. Through the application of mineral admixtures and microscopic analysis to optimize its performance and analyze its mechanisms, its traits as a sustainable building option may be further improved. This study primarily examines the impact of the optimal blend quantities of fly ash, silica fume, and reinforcing agent on the attributes, micro-morphology, and phase composition of porous concrete. The optimal admixture was chosen after analyzing the effects of various factors on the mix ratio and properties of permeable concrete. To understand the degree of impact, performance tests were conducted on the 28-day compressive strength, water permeability coefficient, and porosity. Furthermore, the micro-mechanisms of the admixtures and reinforcing agents on the properties of permeable concrete were analyzed from a microscopic point of view using scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. This research found that the advantageous properties of permeable concrete were enhanced by the simultaneous integration of appropriate quantities of fly ash, silica fume, and reinforcing agent. This resulted in a 28-day compressive strength of 18.33 MPa and a permeability coefficient of 8.27 mm/s. Compared with the unadulterated mineral admixture, the optimal admixture of fly ash, silica fume, and reinforcing agent at the same time increased the 28-day compressive strength by about double; the permeability coefficient was reduced by 36%, but it was still at a high level; and the measured porosity did not differ much from the designed porosity. Through thorough microanalysis, the hydration reaction was significantly improved, which could enhance the microstructure and pore structure of the concrete. This was supported by a substantial increase in the macroscopic compressive strength and a decrease in the water permeability coefficient, which were consistent with the aforementioned enhancement found in the microanalysis. [ABSTRACT FROM AUTHOR]

This study considers 12 pervious concrete mixes incorporating 100% recycled coarse aggregate from old concrete demolition waste and containing various amounts of natural fine aggregate and date palm leaves fibers. First, the properties of the recycled aggregate in terms of their particle size distribution, abrasion resistance, crushing values, specific gravity and water absorption are obtained. Next, the pervious concrete density, compressive strength, tensile strength, permeability and porosity are determined by experimental testing following the relevant standards. The results are analyzed and compared to determine the influence of using recycled coarse aggregate in the mixtures and the impact of the amount of natural sand and volume fraction of the fibers on the mechanical properties, permeability and porosity of the concrete. Findings of the study showed that the use of recycled coarse aggregate in pervious concrete without fine aggregate reduced the compressive strength by 36% and tensile strength by 57%. Replacing 11.7% of the recycled coarse aggregate with natural sand and adding date palm leaves fibers in an amount equivalent to 0.64% volumetric content to such concrete helped increase the compressive strength by 16.2% and tensile strength by 3.2% above the corresponding strengths of the control mix. There is a clear relationship between permeability and porosity due to their correlation with the density of pervious concrete, and the effect of porosity on tensile strength is more influential than it is on the compressive strength. An equation that can predict the tensile strength of pervious concrete from the compressive strength is proposed, as a function of the natural fine aggregate fraction of the coarse aggregate and volumetric content of natural fibers. Results of the research confirm the feasibility of using recycled aggregate in pervious concrete mixes and the positive impact of natural fibers on the mechanical properties. [ABSTRACT FROM AUTHOR]

To assess the freeze–thaw (F-T) durability of coal gangue pervious concrete (CGPC) in different F-T cycle media (water, 3.5 wt% NaCl solution), experimental studies on 36 groups of cube specimens and 6 groups of prismatic specimens were carried out, with designed porosity, F-T cycling media, and F-T failure times as variables. The changes in apparent morphology, mass, compressive behavior, relative dynamic elastic modulus, and permeability coefficient have been analyzed in detail. To predict the compressive strength after F-T cycles, a GM (1,1) model based on the grey system theory was developed and further improved into a more accurate grey residual–Markov model. The results reported that the cement slurry and coal gangue aggregates (CGAs) on the specimen surface continued to fall off as F-T cycles increased, and, finally, the weak point was fractured. Meanwhile, the decrease in compressive behavior and relative dynamic elastic modulus was gentle in the early phase of F-T cycles, and they gradually became faster in the later stage, showing a parabolic downward trend. The permeability coefficient increased gradually. When F-T failure occurred, specimen mass dropped precipitously. The F-T failure of CGPC was more likely to occur in 3.5 wt% NaCl solution, and the F-T failure times of samples were 25 times earlier than that of water. This study lays the foundation for an engineering application and provides a basis for the large-scale utilization of CGPC. [ABSTRACT FROM AUTHOR]

Permeable pavements can decrease the volume of stormwater, thereby mitigating the risk of flooding and reducing the urban heat island effect. This study investigated the influence of incorporating granulated blast-furnace slag (GBFS), hydroxypropyl methylcellulose (HPMC), and polypropylene plastic textile fiber (PPTF) on the mechanical properties and water permeability of pervious concrete. Orthogonal tests were employed to conduct the analysis. The findings indicate that the pervious concrete with GBFS, HPMC, and PPTF (termed GBFS-HPMC/fiber pervious concrete) exhibited the highest cubic compressive strength, ultimate tensile strength, and flexural strength. These values were 25.22 MPa, 3.36 MPa, and 5.39 MPa, respectively. The standard deviations for cubic compressive strength, split tensile strength, flexural strength, water permeability coefficient, and porosity, as calculated using SPSS, were 1.57, 0.1, 1.17, 0.35, and 0.4, respectively. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) were used to analyze the microstructure and compositional combinations of the pervious concrete. The analyses revealed that the calcium-silicate-hydrate (C-S-H) gel, produced by GBFS hydration, enhanced the bonding within the interfacial transition zone (ITZ) and between the fibers and aggregates. Additionally, the anchoring and supporting effects of the PPTF in the matrix contributed to stabilizing the overall matrix structure. Lastly, a gray correlation analysis was applied to optimize the admixture. The findings indicate that following the optimization, the cubic compressive strength increased by 7.2%, splitting tensile strength by 2.1%, and flexural strength by 2.5%. In summary, the mechanical properties of pervious concrete improved after optimizing the admixture. [ABSTRACT FROM AUTHOR]

Due to its properties, pervious concrete is usually considered a material of choice for permeable surfaces. However, its permeability properties, as well as mechanical performance, depend on its effective porosity. In this paper, the Authors investigated the influence of material and technological factors on the selected properties of pervious concrete. A new method, based on the Vebe consistency test method, was developed to assess the vibration time required to reach a designed effective porosity of pervious concrete. Five classes of pervious concrete's consistency measured by the modified vebe method were proposed, and the limiting values to determine optimum vibration time were indicated. A model of dependence between the porosity of pervious concrete, its consistency, and compaction time was proposed. It was found that for the assumed range of variability, compaction time and material composition significantly influence the porosity of pervious concrete, and, therefore, all properties of pervious concrete. [ABSTRACT FROM AUTHOR]

The aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and length of 54 mm were deliberately used to strengthen the joints among grains (max size 31.5 mm). Eight batches of designed mixes were used in the production of pervious concrete at fixed water/binder ratio of 0.34 with cement content of 350 kg/m3. Results showed that the use of recycled concrete aggregate (8/31.5 mm) with replacement ratio of 50% (by weight of aggregate) improved the mechanical properties of pervious concrete in all analyzed cases. Whereas the replacement of 10% rubber waste aggregate (2/5 mm) by volume of aggregate reduced the compressive strength by a maximum of 11.4%. Addition of 2 kg/m3 of polymer fibers proved the strengthening effect of concrete structure, enhancing the compressive and tensile strengths by a maximum of 23.4% and 25.0%, respectively. The obtained test results demonstrate the possibility of using the recycled waste aggregates in decarbonization process of pervious concrete production, but further laboratory and field performance tests are needed. [ABSTRACT FROM AUTHOR]

It is important to balance the characteristics of pervious concrete, such as mechanical, physical, and durability properties. To obtain a better performance, adding fibers is very effective. In this study, samples with different polypropylene fiber content (0 kg/m3, 3 kg/m3, 6 kg/m3, and 9 kg/m3) were designed to test the strength, porosity, permeability, acid corrosion behavior, and low-temperature performance of pervious concrete. It can be found from the experimental results that, compared to the control samples (without the addition of fibers), when the mixing amount of fiber is 6 kg/m3, the cubic compressive strength, axial compressive strength, and flexural tensile strength increase by 35.32%, 37.16%, and 13.04%, respectively; the porosity and permeability coefficient decrease by 36.32 % and 49.30%, respectively; the strength of samples with acidic corrosion times of 0 d, 20 d, 40 d, and 60 d increased by 30.96%, 17.41%, 15.47%, and 20.87%, respectively; and the strength of samples at temperatures of −20 °C, −10 °C, 0 °C, and 25 °C decrease by 14.17%, 15.45%, 22.97%, and 30.96%, respectively. The meso-structure of pervious concrete is studied using industrial computed tomography (ICT) to investigate the relationships between the characteristics. It could be seen that the optimal dosage of polypropylene fiber is 6 kg/m3, which is more suitable for application in engineering. [ABSTRACT FROM AUTHOR]

Concrete with light weight and pervious performance has been widely recognized as an effective and sustainable solution for reducing the negative impacts of urbanization on the environment, as it plays a positive role in urban road drainage, alleviating the urban heat island effect and thermal insulation, as well as seismic performance, etc. This research paper presents a feasibility study of pervious concrete preparation with ceramsite as aggregate. First, pervious concrete specimens with different types of aggregates at various water–cement ratios were prepared, and the mechanical properties of pervious concrete specimens were evaluated based on the compressive strength test. Then, the permeability properties of the pervious concrete specimens with different types of aggregates at various water–cement ratios were characterized. Meanwhile, statistical analysis and regression fitting were conducted. Finally, the analysis of the freeze–thaw durability of pervious concrete specimens with ceramsite as aggregate according to indexes including quality loss rate and strength loss rate was performed. The results show that as the water–cement ratio increased, the compressive strength and permeability coefficient of pervious concrete generally decreased. Compressive strength and permeability coefficient showed a great correlation with the water–cement ratio; the R2 values of the models were around 0.94 and 0.9, showing good regression. Compressive strength was mainly provided by the strength of the aggregates, with high-strength clay ceramsite having the highest 28-day compressive strength value, followed by ordinary crushed-stone aggregates and lightweight ceramsite. Porosity was mainly influenced by the particle size and shape of the aggregates. Lightweight ceramsite had the highest permeability coefficient among different types of cement-bound aggregates, followed by high-strength clay ceramsite and ordinary crushed-stone aggregates. The quality and compressive strength of pervious concrete specimens decreased with the increase in freeze–thaw cycles; the quality loss was 1.52%, and the compressive strength loss rate was 6.84% after 25 freeze–thaw cycles. Quadratic polynomial regression analysis was used to quantify the relationship of durability and freeze–thaw cycles, with R2 of around 0.98. The results provide valuable insights into the potential applications and benefits of using ceramsite as an aggregate material in pervious concrete for more sustainable and durable infrastructure projects. [ABSTRACT FROM AUTHOR]

To improve the comprehensive performance of pervious concrete, the properties of pervious concrete in different paste–aggregate ratios were subjected to both early CO2 curing and uncarbonated curing conditions. The mechanical properties, water permeability, porosity, and chemical composition of pervious concrete under two curing conditions were investigated and compared. The effects of CO2 curing on the properties of pervious concrete with different paste–aggregate ratios were derived. Through mechanical experiments, it was revealed that early CO2 curing can enhance the mechanical strength of pervious concrete by about 15–18%. Meanwhile, with the increase in the paste–aggregate ratio, the improvement effect induced by early CO2 curing became more significant. The water resistance of carbonated concrete was not significantly reduced. And with the increase in the paste–aggregate ratio, the carbonation degree of pervious concrete was reduced; the differences in porosity and water resistance became less significant when the paste–aggregate ratio exceeded 0.39. Micro-structural analysis shows that the early CO2 curing reduced both total porosity and the volume of micropores with a pore diameter of less than 40 nm, while it increased the volume of pores with a diameter of more than 40 nm. This is also the main reason that the strength of pervious concrete under early CO2 curing is higher than that without CO2 curing. The effect of varying paste–aggregate ratio and curing methods adds to the limited knowledge of the performance of pervious concrete. [ABSTRACT FROM AUTHOR]

Pervious concrete has been reported as a viable solution to reduce stormwater run-off, the heat-island effect, road noise, and pavement flooding. Previous researchers have focused on analysing the structural properties and functionality of pervious concrete. However, relatively few studies have been conducted into the addition of supplementary cementitious materials (SCMs), such as calcined clay, in pervious concrete and its effect on long-term durability. This paper has studied the effect of calcined clay pozzolan as a partial substitute for Portland cement in pervious concrete, together with the influence of coarse aggregate size. A water–binder ratio of 0.4 and aggregate–binder ratio of 4.0, as well as a superplasticiser content of 0.95%, were maintained for all mixes. Two sizes of coarse aggregates were used for this study: 9.5 mm and 20 mm. CEM-I cement was partly substituted with calcined clay in dosages of 0 to 30% in replacement intervals of 5%. The mechanical tests conducted included the split tensile test, compressive strength test, and flexural strength test. Durability measurements such as the rapid chloride permeability test (RCPT), thermal conductivity and sulphate resistance tests were also carried out. The mechanical properties of the pervious concrete followed a similar trend. The results showed that at 20% replacement with calcined clay, the compressive strength increased by 12.7% and 16% for 9.5 mm and 20 mm aggregates, respectively. The flexural strength improved by 13.5% and 11.5%, whereas the splitting tensile strength increased by 35.4% and 35.7%, respectively, as compared to the reference concrete. Beyond 20% replacement, the tested strengths declined. The optimum calcined clay replacement was found to be 20% by weight. Generally, pervious concrete prepared with 9.5 mm obtained improved mechanical and durability properties, as compared to those of 20 mm aggregates. [ABSTRACT FROM AUTHOR]

With rapid urban development, natural aggregate resources have become scarce and a large number of ageing buildings are being demolished, which has resulted in a significant reduction in natural resources and a large increase in construction waste. Therefore, the reuse of solid waste, including waste powder and recycled aggregate, has attracted more and more attention. Additionally, as a prominent way to alleviate the urban heat island effect and manage stormwater runoff, pervious concrete has been widely studied and applied. In this paper, the effects of waste powder (fly ash, volcanic powder and blast furnace slag) and recycled aggregate (recycled concrete aggregate and recycled brick aggregate) on the mechanical properties, water permeability, water filtration and durability of pervious concrete are summarized and introduced, and some prospects are put forward. From the literature review, it can be found that adding the appropriate amount of solid waste or applying proper treatment methods to solid waste will not bring negative effects; rather, it would even improve the performance attributes of pervious concrete. Therefore, the use of solid waste in pervious concrete has great potential for urban construction and environmental protection. [ABSTRACT FROM AUTHOR]

The urban heat island (UHI) effect poses significant challenges to urban environmental quality and public health. Over the decades, research efforts have been made to develop various UHI mitigation strategies, including pavement materials, such as, water-retentive pavement, reflective pavement, and pervious concrete. This paper focuses on the improvement of the hygric and water retention properties of pervious concrete to mitigate UHI phenomena. The hydric and hygroscopic tests were carried out under dry and wet conditions on four different pervious concretes, where natural aggregates were replaced with recycled aggregates at different mass percentages. The results show a significant improvement in these properties by increasing the amount of recycled aggregates incorporated in the mixtures. The mixes made from recycled aggregates alone showed an absorption that reached 75 L more than the control in one cubic meter under wet condition. With an upwelling capacity of up to 30 kg of retained water in a square meter under dry condition, these improvements in water performance represent this permeable concrete as a water retention pavement solution for UHI mitigation. Regarding the mechanical properties, a decrease of 50% in compressive strength was noted only when 100% of the recycled aggregate was incorporated, remaining at 20 MPa for other mixtures. [ABSTRACT FROM AUTHOR]

In recent years, China has entered a period of rapid urban development, but most of the cities with rapid development still have ground hardening, which makes it difficult for rainwater to penetrate and discharge. In order to achieve the rapid drainage of accumulated water in the city, nanotechnology was introduced, and permeable concrete based on NC and NS nanomaterials was proposed. Combined with finite element analysis, the permeable properties and mechanical properties of permeable concrete mixed with nanomaterials were analyzed. A comprehensive performance analysis of pervious concrete shows that the viscosity of permeable concrete mixed with nanomaterials is significantly higher than that of non-mixed pervious concrete, and the permeability coefficient of permeable concrete mixed with nanomaterials can reach 0.43 cm/s. A finite element analysis shows that the incorporation of nanomaterials can improve the compressive strength of permeable concrete. At the same time, under a rainwater environment simulation, the rainwater retention time of pervious concrete is only 2.35 s. The above results show that the incorporation of nanomaterials into pervious concrete can improve the water permeability of pervious concrete, improve the mechanical properties of pervious concrete, and increase its service life, which is of great significance to urban development and urban management. [ABSTRACT FROM AUTHOR]

To study the performance of recycled aggregate pervious concrete (RAPC) in severe cold regions, the influence of the water–binder ratio, design porosity, micro silica fume (SF) and enhancer agent (EA) on the permeability and mechanical properties of the RAPC were evaluated using the orthogonal design method. Based on the optimal mixture proportion, freeze–thaw (F-T) experiments were carried out to investigate the effect of different media (water, 3.5 wt% NaCl solution) on the mechanical properties, permeability and anti-frost durability of the RAPC. Moreover, the porosity and pore structure characteristics of RAPC were evaluated after frost damage using an X-ray CT technique. The results indicate that the influence of the salt solution on the deterioration of the RAPC specimen is greater than water. The deterioration degree of the mass loss ratio, relative dynamic elastic modulus (RDEM), average compressive strength and porosity of the RAPC increase with increasing F–T cycles. Based on the two-parameter Weibull probabilistic distribution function, damage evolution models of RAPC are established, which can be used to quantitatively characterize the damage degree of the RAPC specimens under different F–T media. The results obtained can provide an experimental reference and data support for the promotion and application of RAPC pavement in severe cold regions. [ABSTRACT FROM AUTHOR]

The excessive production of construction waste is a significant concern as it requires proper disposal and may become economically unfeasible. Reusing construction waste in producing new concrete can substantially reduce the disposal requirements of construction waste. In addition, this results in a sustainable solution for the rapidly depleting natural resources of concrete. Pervious concrete may contain up to 80% coarse aggregates and could be an exceptional host for reusing construction waste. This study aimed to investigate the mechanical properties of pervious concrete constructed with natural and recycled aggregates. The substandard properties of recycled aggregates were improved by adding natural fibers from sackcloth. This study presents an experimental program on 45 samples of pervious concrete with air void ratios and the size of coarse aggregates as the parameters of interest. The compressive strength of the pervious concrete decreased by increasing the air void ratio regardless of the size of the aggregates. The type of aggregates did not influence the permeability of pervious concrete, and the maximum temperature in pervious concrete increased as the quantity of air void ratios increased. The decrease in compressive strength was 40–60% as the void ratio was increased from 10–30% for all types of concrete mixes, such as natural and recycled aggregates. The permeability of small-size aggregates with 10% designed air void ratios for natural and recycled aggregates with sackcloth was 0.705 cm/s. [ABSTRACT FROM AUTHOR]

Pervious concrete (PC) is a multifunctional material with good water permeability, noise reduction, and heat absorption properties. The most critical performance indicators of the PC are permeability and strength, which are mainly affected by the cement paste coating thickness (PCT) on the aggregate surface. The experiment was carried out to study the influence of the water–cement ratio, superplasticizer dosage, aggregate roughness, and aggregate size on PCT, and a new normalization method was proposed for grey correlation analysis to determine the influence degree of the above factors on PCT. Finally, fitting models for predicting the PCT were established based on experimental data. The experimental results indicate that the influence of the water–cement ratio on PCT can be divided into two stages, whereby the PCT shows a slow decline and then a rapid decline with the increase in water–cement ratio; with the increase in superplasticizer dosage, the PCT represents an exponentially decreasing trend; the PCT increases with the aggregate size and aggregate roughness. Based on the grey correlation analysis, the superplasticizer dosage exerts the greatest influence on PCT, followed by the water–cement ratio, aggregate size, and aggregate roughness. The results of this study revealed the change law of PCT under the action of the above factors, which established the premise of controlling the strength and permeability of PC from the perspective of the PCT and provided a reference for the mixture proportion design. [ABSTRACT FROM AUTHOR]

Pervious concrete has good permeability and moisture adjustment properties due to its rich pore structure. It can not only reduce surface runoff by infiltration of rainfall, but also retain a certain amount of water inside, and then decrease the surface temperature via evaporation. In order to optimize the evaporative cooling performance of pervious concrete, this study introduces a modified method of incorporating superabsorbent zeolite produced from industrial wastes into pervious concrete as hygroscopic filler. The effects of zeolite dosages on the basic physical and mechanical properties of pervious concrete were analyzed, and then the evaporative cooling performance of zeolite-modified pervious concrete with the optimum replacement rate was studied. The results showed that the zeolite addition significantly reduced the density of pervious concrete, while having little impact on the permeability. The compressive and splitting tensile strength of pervious concrete increased first and then decreased as the replacement rate of zeolite powder increased, and the content of 15% zeolite powder and 20% zeolite aggregate was beneficial to improve the mechanical properties of pervious concrete. Contributing to the abundant micro-pores and higher specific surface area of zeolite particles, this could improve capillary water absorption and the water storage ability of pervious concrete. During the process of evaporation, the water absorption increment could effectively reduce the surface temperature by 5–8 °C, and maintain the evaporation cooling effect for 10–12 h. [ABSTRACT FROM AUTHOR]

Pervious concrete provides a tailored surface course with high permeability properties which permit the easy flow of water through a larger interconnected porous structure to prevent flooding hazards. This paper reports the modeling of the flexural properties of quarry dust (QD) and sawdust ash (SDA) blended green pervious concrete for sustainable road pavement construction using Scheffe's (5,2) optimization approach. The simplex mixture design method was adapted to formulate the mixture proportion to eliminate the set-backs encountered in empirical or trials and the error design approach, which consume more time and resources to design with experimental runs required to evaluate the response function. For the laboratory evaluation exercise, a maximum flexural strength of 3.703 N/mm2 was obtained with a mix proportion of 0.435:0.95:0.1:1.55:0.05 for water, cement, QD, coarse aggregate and SDA, respectively. Moreover, the minimal flexural strength response of 2.504 N/mm2 was obtained with a mix ratio of 0.6:0.75:0.3:4.1:0.25 for water, cement, QD, coarse aggregate and SDA, respectively. The test of the appropriateness of the developed model was statistically verified using the Student' t-test and an analysis of variance (ANOVA), and was confirmed to be acceptable based on computational outcomes at the 95% confidence interval. Furthermore, the scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) were used to evaluate the morphological and mineralogical behavior of green prior concrete samples with various additive mixture compositions. The addition of QD and SDA, on the other hand, aided the creation of porous microstructures in the concrete matrix due to fabric changes in the concrete mixture, potentially aided by the formation of cementitious compounds such as calcium aluminate hydrate and calcium silicate hydrate. [ABSTRACT FROM AUTHOR]

Pervious concrete is one of the emerging sustainable materials that has recently gained the attention of many researchers. The importance of pervious concrete mainly depends on its application and on a modern integrated approach in which it is employed to reduce the effects of flooding. The main goal of this experimental analysis is to study the significance of aggregate size and the degree of compaction on the mechanical and hydraulic properties of pervious concrete. Eleven concrete mixture proportions were investigated by controlling the constituents with different aggregate fractions. The important variables considered were the aggregate sizes, viz., 0/4 mm, 4/8 mm, and 8/16 mm, with four different degrees of compaction. The porosity of the concrete structure was obtained by the partial filling of the voids in the aggregates with cement paste. The ingredients of the pervious concrete were also varied to study their significance and to evaluate the predominant factor that controls the mechanical and hydraulic properties based on the test results. Tests were conducted to determine properties such as compacting factor, compressive strength, splitting tensile strength, abrasion resistance, porosity, and hydraulic conductivity. The study revealed that the degree of compaction was one of the critical factors governing the strength and hydraulic properties of the pervious concrete; the maximum strength and minimum hydraulic conductivity were achieved with a higher degree of compaction. The test results imply that the cement content is the predominant factor determining the fresh and tensile properties of the pervious concrete, rather than the size of the aggregates used. In addition, the results also illustrated that the highly compacted pervious concrete samples made with 4/8 mm aggregates exhibited improved abrasion resistance and strength properties, but slightly reduced hydraulic conductivity, despite the designed porosity. [ABSTRACT FROM AUTHOR]

Portland cement porous concrete (PCPC) has received immense interest recently due to its environmental aids. Its porous structure helps to reduce the water runoff amount while improving the recharge of groundwater. Earlier studies have concentrated on illustrating and knowing the functional as well as structural properties of PCPC. However, very few studies are available on PCPC in combination with natural silica sources as supplementary cementitious materials (SCMs). Most SCMs are by-products of industrial manufacturing processes and cause some environmental concerns, but with their pozzolanic effect, they could be utilized as partial substitute materials for ordinary Portland cement (OPC) to enhance the strength as well as durability performance. The aim of this study is to evaluate the effects of diatomaceous earth (DE) as a supplementary cementitious material for partial substitution of OPC for Portland cement porous concrete application. Compression strength, split tensile strength, and flexural strength tests were performed to determine the effect of partial replacement. To investigate the impact of test variables, basic tests, including void content and water permeability, were also performed. Compared to the control concrete, the results show that a 15% replacement of cement with DE significantly increased the compressive strength (by 53%) while also providing adequate porosity and better water permeability. Statistical analysis (ANOVA) and regression analysis showed that there is a significant (p < 0.05) growth within the physical characteristics of concrete upon the replacement of cement by 15% DE. Collectively, the replacement of cement with DE could not only improve the concrete strength but also reduce the consumption of cement, thereby lessening the cost of construction as well as indirectly reducing the carbon footprint. [ABSTRACT FROM AUTHOR]

Geopolymer-recycled pervious concrete (GRPC) is a novel concrete that can effectively inhibit the corrosion of acid rain and alleviate urban waterlog. The goal of this study is to ascertain the optimal pore size of GRPC and study its acid rain resistance activated by different alkali-activators. Three different sizes (0.8, 1.0, and 1.2 mm) were separately chosen as the pore diameters of GRPC. The alkali-activator solution adopted sodium hydroxide (NaOH), sodium silicate (Na2SiO3), and a mixture of the two. The mechanical properties and permeability coefficient were tested to determine the optimal pore size of GRPC. After that, specimens with the optimal pore size were immersed in a simulative acid rain solution (sulfuric acid solution with pH = 4.0) for 6 d and were dried 1 d until 56 d. The effects of different alkali activators on acid rain resistance of GRPC were analyzed by compressive strength, neutralization depth, and mass loss. The results manifested that the mechanical properties of GRPC were excellent, the compressive strength of GRPCH+N reached more than 60.1 MPa, and their splitting tensile strength attained more than 5.9 MPa, meeting the strength requirement of the road for heavy traffic load. Considering the mechanical properties and the acid rain purification effect of alkaline GRPC required a relatively small permeability coefficient; the optimal pore size was 1 mm. When specimens with optimal pore size were exposed to acid solution, the corrosion products (gypsums) would block the pores of GRPC to inhibit further corrosion, keeping the stability of the compressive strength. GRPC activated by the mixture of NaOH and Na2SiO3 generated a more stable amorphous three-dimensional network structure, endowing GRPCH+N with better mechanical properties and acid corrosion resistance. [ABSTRACT FROM AUTHOR]

The fine portion of crushed old concrete is difficult to be recycled for use in new concrete because it contains old cement paste, which generally has high porosity and low strength. Hence, in practice, the coarse portion is recycled as coarse aggregate and the fine portion is mostly not recycled. Nevertheless, attempts have been made in recent years to recycle the fine portion as waste concrete powder (WCP) by grinding before use. In this research, WCP was used to make pervious concrete. The WCP was added using the paste replacement method (PR method) of replacing an equal volume of cementitious paste. A series of pervious concrete mixes containing 100% recycled coarse aggregate and having different amounts of WCP added were produced for testing of interconnected porosity, water permeability and strength. The results showed that the addition of WCP using the PR method can improve the interconnected porosity by 9% and water permeability by 18%, greatly enhance the strength by 86%, as well as decrease the cement consumption by 10% at the same time. Therefore, the addition of WCP as paste replacement has great potential to be applied to the production of eco-friendly high-performance pervious concrete. [ABSTRACT FROM AUTHOR]

The interface between aggregate and cement matrix and the strength of the cementation layer between aggregates are the key factors affecting the strength of pervious concrete. The purpose of this paper is to evaluate the effects of porosity, compressive strength and elastic modulus of pervious concrete before and after freeze–thaw cycles. The effective porosity and total porosity were obtained by the underwater weighing and CT (computed tomography) image analysis methods. Uniaxial and triaxle compression tests were carried out to obtain the strength and elastic modulus of pervious concrete considering pore and fiber. The results indicated that the effective modulus and effective stress were closely related to the porosity, and the continuous fracture of cementation points between aggregates caused damage to pervious concrete. Inclined shear failure of pervious concrete occurred under uniaxial pressure, and the strength and elastic modulus increased with increases in confining pressure. With the increase in freeze–thaw cycles, the porosity increased linearly, the strength and elastic modulus decreased and a mutational point appeared between 40 and 50 times during the freeze–thaw cycles. The fiber enhanced the strength of the cementation layer and increased the connection between aggregates, thus improving the strength and integrity of pervious concrete. This work is needed to serve as a reference for the fracture mechanism of pervious concrete and the effect of freeze–thaw cycles considering pore and fiber. [ABSTRACT FROM AUTHOR]

Pervious concrete has good water permeability and, if used in construction, it can alleviate the heat island effect. However, its low strength and poor durability are major obstacles to its use. This study shows that nano-reinforced pervious concrete created by incorporating cellulose nanofibrils (CNFs) can improve the physical properties and increase the durability of pervious concrete. CNFs were added to the concrete mix in proportions ranging from 0.05% to 0.2% by weight of binder. The additions were found to alter matrix rheology. The hydration kinetics of matrix with differing CNF contents were compared and analyzed. The experimental results show the addition of CNFs delayed peak heat flow and maximum cumulative heat. The 28 d compressive strength of pervious concrete increased by up to 26.5% and 28 d flexural strength by up to 25.8% with the addition of 0.05–0.2% CNFs. Addition of 0.1% and 0.2% CNFs increased water permeability. Addition of 0.05–0.15% CNFs decreased mass loss by 73.2–83.7% after 150 freeze–thaw cycles, which corresponded to an increase in frost resistance. Denser matrices and stronger interfacial transition zones were observed using scanning electron microscopy when 0.05–0.2% CNFs were added. [ABSTRACT FROM AUTHOR]

The clogging of porous and permeable pavements is a problem that faces many municipalities and, because of the high associated costs, it has become a major impediment to the uptake of such water sensitive and sustainable technologies. This study has experimentally examined the performance of seven cleaning methods that were shown to be able to restore higher infiltration rates in partially clogged pavement systems. It was found that high-pressure water injection was the most effective cleaning method, particularly when combined with vacuuming. The highest restoration of infiltration rate was achieved using high-pressure water injection combined with the highest-pressure vacuum, which produced an average increase in infiltration rate of 20.9%. Cleaning a porous pavement involves removing the sediment that has caused clogging in the first place. In normal circumstances, this collected sediment would have to be dried before disposal to a landfill, which is another costly process. Through a sustainability analysis, the potential reuse of collected sediment was investigated and it was found that the resulting economic and environmental benefit-cost ratios were high. [ABSTRACT FROM AUTHOR]

The aim of this study was to investigate the properties of fiber-reinforced pervious concrete. Ordinary cement, silica fume, coarse aggregate, and basalt fibers were used to produce the concrete mix. The fibers were mixed with pervious concrete at the levels of 0 kg/m3, 2 kg/m3, 4 kg/m3, 6 kg/m3, and 8 kg/m3 to the investigate their influence on the mechanical and physical properties of pervious concrete. It could be observed that the cubic compressive strength, axial compressive strength, and flexural strength increased and then decreased as the content of basalt fiber increased, while the permeability and porosity of the pervious concrete decreased with the increase in the basalt fiber content. The mesostructure of pervious concrete was also studied through industrial computed tomography (ICT); the testing phenomenon showed that the fibers had a significant influence on the arrangement of the aggregate, cement paste, and the interfacial transition zone, and excessive basalt fiber resulted in poor characteristics of the interfacial transition zone (ITZ) and inferior strength properties. It was found that incorporating a basalt fiber content of 4 kg/m3 could achieve a balance between the mechanical and physical properties of pervious concrete, which was suitable for structural applications. [ABSTRACT FROM AUTHOR]

The water and gas permeability of pervious concrete play essential roles in rainwater infiltration and plant root respiration. In this study, the gas and water permeability of pervious concrete samples were measured and compared. The water permeability was tested using the constant water head method and several water heads were measured for inspection, in which the permeability varied with the application of the pressure gradient. The permeability of gas was measured using a new simple gas permeameter, which was specially manufactured for measuring the gas permeability of pervious concrete under a stable pressure difference. A series of different gas pressure gradients was applied to test whether the gas permeability was a function of the applied pressure. Both the gas and water permeability of pervious concrete were found to decrease with an increased applied pressure gradient, which did not conform to the Klinkenberg effect (gas slippage effect). When comparing the gas permeability and water permeability of pervious concrete, we found that the water permeability was 4–5 times larger than the gas permeability. [ABSTRACT FROM AUTHOR]

This paper evaluates the effect of mix design parameters on the mechanical, hydraulic, and durability properties of pervious geopolymer concrete (PGC) made with a 3:1 blend of granulated blast furnace slag (GBFS) and fly ash (FA). A total of nine PGC mixtures were designed using the Taguchi method, considering four factors, each at three levels, namely, the binder content, dune sand addition, alkaline-activator solution-to-binder ratio (AAS/B), and sodium hydroxide (SH) molarity. The quality criteria were the compressive strength, permeability, and abrasion resistance. The Taguchi and TOPSIS methods were adopted to determine the signal-to-noise (S/N) ratios and to optimize the mixture proportions for superior performance. The optimum mix for the scenarios with a compressive strength and abrasion resistance at the highest weights was composed of a binder content of 500 kg/m3, dune sand addition of 20%, AAS/B of 0.60, and SH molarity of 12 M. Meanwhile, the optimum mix for the permeability-dominant scenario included a 400 kg/m3 of binder content, 0% of dune sand addition, 0.60 of AAS/B, and 12 M of SH molarity. For a balanced performance scenario (i.e., equal weights for the responses), the optimum mix was similar to the permeability scenario with the exception of a 10% dune sand addition. An ANOVA showed that the binder content and dune sand addition had the highest contribution toward all the quality criteria. Multivariable regression models were established to predict the performance of the PGC using the mix design factors. Experimental research findings serve as a guide for optimizing the production of PGC with a superior performance while conducting minimal experiments. [ABSTRACT FROM AUTHOR]

Based on the design of a prefabricated pervious composite cement concrete pavement slab, the interface properties and bending deformation properties of basalt pervious concrete (BPC) and PVA fiber base impervious concrete (PFBIC) composite specimens were studied. The effects of the different interfacial agents on the interfacial bonding performance were compared using a splitting tensile strength test and interfacial shear test. The deformation capacity of the composite specimens under bending load was tested using a three-point bending test, with the symmetry of the model considered and compared with the deformation capacity of the BPC specimen and PFBIC specimen. The results showed that the compressive strength of the BPC prepared using an orthogonal test reached 40.30 MPa, while the permeability coefficient was 2.41 mm/s. Different interface treatment processes determine the interface bonding properties. The best interface treatment method can induce the interface bonding strength to be higher than the strength of the BPC matrix itself, while the interface transition zone matrix will be denser without obvious microscopic defects. Under the bending tensile load, the ultimate bending stress reached 6.58 MPa and the maximum deflection in the midspan was 0.81 mm. As a protective layer, the PFBIC can alleviate the disadvantage of the insufficient strength of the BPC and can improve the bending ultimate bearing capacity of the BPC-PFBIC through its own stiffness. [ABSTRACT FROM AUTHOR]

Impervious pavement surfaces within urban areas present serious environmental problems due to waterlogging, flooding and in particular, the urban heat island (UHI) phenomenon. Another issue that has recently been highlighted is user comfort in pedestrian and cycling areas. Materials that have potential for overcoming these issues include pervious concrete (PC), a new type of construction material with improved drainage properties and thermal properties. In this study, the thermal properties and behavior of commonly used concrete paving materials in urban areas (dense concrete (DC) and concrete pavers (P)) and pervious concrete (PC) paving flags were investigated and compared in terms of their thermal properties. Material behavior under different temperature conditions was investigated within laboratory research measuring thermal conductivity (λ) and the capacity for heating and cooling using infrared lamp. Complementary to laboratory tests, field research was conducted analyzing the surrounding conditions on pavement wearing course behavior under real weather conditions. Dense concrete paving material had the highest thermal conductivity coefficient and heat absorption capacity, and slowest heating and cooling speed, compared with the other paving materials. The results also highlighted the similar thermal properties of PC and P but with potentially improved user comfort for PC due to its draining properties. The base layer and surrounding characteristics had a significant influence on the thermal behavior of pavements, and future research should consider these parameters when addressing the UHI effect for different paving materials. [ABSTRACT FROM AUTHOR]

This study evaluated the co-remediation performance of an active–passive process comprised of passive permeable reactive barrier acid mine drainage (AMD) pre-treatment and active anaerobic digestion treatment of AMD with effluent as a carbon source. The bioreactor was operated for 24 consecutive days with peak chemical oxygen demand (COD) and sulphate loading rates of 6.6 kg COD/m3/day and 0.89 kg SO42−/m3/day, respectively. The AMD pre-treatment was capable of removing 99%, 94% and 42% of iron (Fe), potassium (K), and aluminium (Al) concentrations, respectively. The biological treatment process was capable of removing 89.7% and 99% of COD and sulphate concentrations, respectively. The treated wastewater copper (Cu), sulphate (SO42−), and pH were within the effluent discharge limits and the potable water standards of South Africa. Fe, Al, manganese (Mn), nickel (Ni), and zinc (Zn) concentrations in the treated wastewater were marginally higher than the discharge and potable water limit with all concentrations exceeding the limit by less than 0.65 mg/L. The remediation performance of the process was found to be effective with limited operational inputs, which can enable low cost co-remediation. [ABSTRACT FROM AUTHOR]