Search

Metal- μ hemispherical resonant gyros (M- μ HRGs) are widely used in highly dynamic navigation systems in extreme environments due to their high accuracy and structural stability. However, the effect of temperature variations on the capacitance characteristics of M- μ HRGs has not been fully investigated, which is crucial for optimizing the performance of the gyro. This study aims to systematically analyze the effect of temperature on the static and dynamic capacitances of M- μ HRGs. In this study, an M- μ HRG structure based on a 16-tooth metal oscillator is designed, and conducted simulation experiments using non-contact capacitance measurement method and COMSOL Multiphysics 6.2 finite element simulation software in the temperature range of 233.15 K to 343.15 K. The modeling analysis of the static capacitance takes into account the thermal expansion effect, and the results show that static capacitance remains stable across the measured temperature range, with minimal effect from temperature. The dynamic capacitance exhibits significant nonlinear variations under different temperature conditions, especially in the two end temperature intervals (below 273.15 K and above 313.15 K), where the capacitance values show local extremes and fluctuations. In order to capture this nonlinear behavior, the experimental data were smoothed and fitted using the LOESS method, revealing a complex trend of the capacitance variation with temperature. The results show that the M- μ HRG has good capacitance stability in the mid-temperature range, but its dynamic performance is significantly affected at extreme temperatures. This study provides a theoretical reference for the optimal design of M- μ HRGs in high- and low-temperature environments. [ABSTRACT FROM AUTHOR]

With advancements in seismic isolation and damping technology, high-damping rubber (HDR) bearings are now widely used. However, significant gaps remain in HDR-analysis model research, with few studies integrating multiple factors, the Mullins effect, and stiffness hardening for more accurate practical predictions. This study classifies the effective behavior of HDR and examines the stress–strain relationships of different behavioral types using more appropriate equations. Mathematical models were established based on pseudo-elasticity theory, which is an extension of continuum mechanics. Subsequently, parameter functions were developed through parameter determination tests and regression analysis, leading to the completion of the pseudo-elastic model for HDR. Finally, the model's effectiveness was validated through validation tests. This study finds that behavior classification effectively examines phenomenological-based HDR stress–strain relationships, as distinct behavioral patterns are not adequately captured by a single approach. Incorporating tests to functionalize material parameters complements theoretical models. Additionally, accurately explaining HDR behavior requires considering the Mullins effect and stiffness hardening, influenced by the coupled effects of temperature, strain amplitude, and compressive stress. Consequently, this HDR pseudo-elastic model offers a comprehensive explanation of HDR behavior, including the Mullins effect and stiffness hardening, under various influencing factors based on clear mechanical principles and explicit computational procedures. [ABSTRACT FROM AUTHOR]

Energy from municipal sewage sludge can be obtained by applying a thermal conversion method. In this study, the combustion kinetics of municipal sewage sludge were analyzed in an O2/CO2 atmosphere. Studies were conducted in different gaseous atmospheres consisting of varying proportions of oxygen and carbon dioxide. The participation of oxygen was as follows: 20, 40, 60, 80 and 100% vol. The experimental temperatures varied from 873 to 1273 K. The experimentally obtained results helped establish the basic kinetic parameters, such as the reaction order n, factor Ko and activation energy Ea of sludge grains. The values of the activation energy Ea and Ko were, respectively, 46 kJ/mol and 0.0127 mg/m2sPa. They show that the limiting factor of combustion is the diffusion of oxygen and that combustion reactions take place in the outer layer of the unreacted core. Therefore, sludge is promising for energy recovery because it has quite a high net calorific value (NCV) and a high gross calorific value (GCV). The GCV was 14.1 MJ/kg and the NCV was 12.8 MJ/kg. The experimental studies with a wide range of process parameters helped to create an array of apparent reaction rates as a function of the temperature and oxygen concentration, showing the significant effect of oxygen on the apparent reaction rate, in contrast to the effect of temperature. [ABSTRACT FROM AUTHOR]

The influence of carrier mobility on the space charge transport behavior inside the oil-impregnated pressboard insulation of converter transformers cannot be neglected. However, at present, current knowledge is usually derived from empirical or theoretical values, lacks experimental studies, and often ignores the effects of temperature and field strength under actual operating conditions. In this paper, based on the variable-temperature surface potential decay (SPD) method, a carrier mobility measurement platform for oil-impregnated pressboard is established, and the carrier mobility values for different combinations of oil and oil-impregnated pressboard are obtained experimentally to analyze and reveal the influence mechanisms of temperature and field strength on the carrier mobility. The results indicate the following: (1) The positive and negative carrier mobilities of oil-impregnated pressboard are in the range of 10−12–10−13 m2·V−1·s−1, and the negative carrier mobility is always higher than the positive carrier mobility. (2) The carrier mobility is positively correlated with the changes of temperature and field strength, and when the temperature increases from 20 °C to 80 °C, the positive and negative carrier mobilities increase by 4.01 times and 4.72 times, respectively; when the field strength increases from 1 kV/mm to 7 kV/mm, the positive and negative carrier mobility increases by 2.53 and 2.72 times, respectively. (3) The carrier mobility of the pressboard with a higher oil absorption rate changes more significantly with temperature; when the field strength is 7 kV/mm and the temperature increases from 20 °C to 80 °C, the positive polarity carrier mobility increases from 3.96 × 10−13 m2·V−1·s−1 to 2.64 × 10−11 m2·V−1·s−1, an increase of 66.67 times, while the increase in the carrier mobility of the pressboard with a lower oil absorption rate is only 1.59 times. (4) The carrier mobility of the naphthenic transformer oil-impregnated pressboard is higher than that of the paraffin-based transformer oil-impregnated pressboard, and the carrier mobility of two kinds of naphthenic transformer oil-impregnated pressboard is 3.16 times and 2.47 times higher than that of the paraffin-based transformer oil-impregnated pressboard, respectively, under the conditions of 60 °C and 7 kV/mm. (5) Utilizing the Darcy model and microscopic scanning results of the pressboard morphology, it was revealed that permeability and fiber structure are key factors influencing the variation in carrier mobility. The research results of this paper can provide theoretical basis for the calibration and optimization of the oil-pressboard insulation structure of converter transformers. [ABSTRACT FROM AUTHOR]

Among many iron-based superconductors, isovalently substituted BaFe2(As1−xPx)2 displays, for x ≈ 0.3, apart from the quite usual Second Magnetization Peak (SMP) in the field dependence of the critical current density, an unusual peak effect in the temperature dependence of the critical current density in the constant field, which is related to the rhombic-to-square (RST) structural transition of the Bragg vortex glass (BVG). By using multi-harmonic AC susceptibility investigations in three different cooling regimes—field cooling, zero-field cooling, and field cooling with measurements during warming up—we have discovered the existence of a temperature region in which there is a pronounced magnetic memory effect, which we attributed to the direction of the structural transition. The observed huge differences in the third harmonic susceptibility at low and high AC frequencies indicates the difference in the time-scale of the structural transition in comparison with the timescale of the vortex excitations. Our findings show that the RST influence on the vortex dynamics goes beyond the previously observed influence on the onset of the SMP. [ABSTRACT FROM AUTHOR]

The optical remote sensors carried by the Jilin-1 KF02 series satellites have an imaging resolution better than 0.5 m and a width of 150 km. There are radiometric problems, such as stripe noise, vignetting, and inter-slice chromatic aberration, in their raw images. In this paper, a relative radiometric correction method based on temperature normalization is proposed for the response characteristics of sensors and the structural characteristics of optical splicing of Jilin-1 KF02 series satellites cameras. Firstly, a model of temperature effect on sensor output is established to correct the variation of sensor response output digital number (DN) caused by temperature variation during imaging process, and the image is normalized to a uniform temperature reference. Then, the horizontal stripe noise of the image is eliminated by using the sensor scan line and dark pixel information, and the vertical stripe noise of the image is eliminated by using the method of on-orbit histogram statistics. Finally, the method of superposition compensation is used to correct the vignetting area at the edge of the image due to the lack of energy information received by the sensor so as to ensure the consistency of the image in color and image quality. The proposed method is verified by Jilin-1 KF02A on-orbit images. Experimental results show that the image response is uniform, the color is consistent, the average Streak Metrics (SM) is better than 0.1%, Root-Mean-Square Deviation of the Mean Line (RA) and Generalized Noise (GN) are better than 2%, Relative Average Spectral Error (RASE) and Relative Average Spectral Error (ERGAS) are greatly improved, which are better than 5% and 13, respectively, and the relative radiation quality is obviously improved after relative radiation correction. [ABSTRACT FROM AUTHOR]

This study focused on optimizing a cold water extraction method to obtain bioactive compounds from chamomile (Matricaria chamomilla L.), addressing increasing consumer demand for natural products and nutraceuticals. A full-factorial design was employed to evaluate the effects of temperature, time, and chamomile amount on the polyphenolic profile of extracts. The samples were characterized by HPLC-DAD and UV-Vis coupled with chemometrics; the analysis showed that extraction time negatively affected extract quality, as did the interaction between time and temperature. In addition, a significant positive quadratic effect for temperature and a positive coefficient for chamomile amount was found. ASCA was used to assess the UV-Vis profile, offering an alternative untargeted method for understanding the variable effects. The optimal extraction conditions (25 °C, 32 min, and 2.5 g of chamomile) produced samples high in hydroxybenzoic and hydroxycinnamic acids and flavanol derivatives. Using A face-centered design, this study also monitored antioxidant activity via a DPPH scavenging assay, confirming that the optimal conditions yielded samples within the range of maximum antioxidant activity in the studied experimental domain. [ABSTRACT FROM AUTHOR]

The high-temperature and high-humidity conditions arising from the biochemical degradation of landfill waste result in significant temperature gradients within the landfill cover. The effects of waste temperature on landfill gas transport and microbial aerobic methane oxidation are not fully understood. In this study, a fully coupled theoretical model was developed to simulate the interactions of moisture, heat, and gas transport within a capillary barrier cover. A series of parametric studies were carried out to investigate the influence of the combined effects of temperature gradient, initial soil moisture content, and landfill gas generation rate on methane transport, oxidation, and emissions. The simulated results indicated that increasing waste temperature intensified the temperature gradient, leading to higher surface evaporation rates and variations in methane oxidation efficiencies. Additionally, variations in initial soil moisture content and landfill gas generation rates were found to significantly impact gas migration and methane oxidation in the cover. This study demonstrates the critical role of waste temperature in landfill gas migration within landfill cover systems, providing technical methodologies for the optimized design of soil cover systems. [ABSTRACT FROM AUTHOR]

In the lab experiments, the compressive strength (CS) of cement mortar, three pre-setting water/binder (W/B) ratios, five substitution rates of burned joss paper ash (SR-BJPA), and three curing temperatures (T) were tested for the 45 samples. The results were recorded at 3, 7, 28, 56, 90, and 120 days after curing (#days) for each sample. The correlations between CS and each experimental factor (W/B ratio, SR-BJPA, T, and #days) and the effects of each factor or pair of factors on CS were determined using four univariate and six bivariate regression models. All the models were significant (i.e., the factors and the pairs of factors can be used to predict CS); however, each model had a different ability to fit the data and explain the data variance, making some models not that suitable. The effects on CS of substituting cement with different BJPA proportions and curing the mortar at different temperatures were mainly identified. A knowledge base for predicting the CS was established before any sample is to be made in future practise. Finally, using an SR-BJPA of 5% and raising the curing temperature to 50 °C (or 75 °C, if additional heating energy consumption needs not be considered) while keeping the W/B ratio at 0.4 is recommended to obtain an optimal CS for the full-aged sample (i.e., at #days = 120) in future practise, subject to the aim to consume the BJPA wastes by using it to replace Portland cement, in order to reduce the vast volume of carbon emitted along with the production of the cement material. [ABSTRACT FROM AUTHOR]

Yellowing is the key processing technology of yellow tea, and environmental conditions have a significant impact on the yellowing process. In this study, volatile compounds of the yellowing process under different environmental conditions were analyzed by GC–MS. Results showed that a total of 75 volatile compounds were identified. A partial least squares discriminant analysis (PLS-DA) determined that 42 of them were differential compounds, including 12 hydrocarbons, 8 ketones, 8 aldehydes, 6 alcohols, and 8 other compounds, and compared the contents of differential compounds under the conditions of 40 °C with 90% humidity, 50 °C with 50% humidity, and 30 °C with 70% humidity, then analyzed the variation patterns of hydrocarbons under different yellowing environmental conditions. A 40 °C with 90% humidity treatment reduced the content of more hydrocarbons and increased the aldehydes. The content of 3-hexen-1-ol was higher when treated at 50 °C with 50% humidity and was consistent with the results of sensory evaluation. This study could provide a theoretical basis for future research on the aroma of yellow tea. [ABSTRACT FROM AUTHOR]

Halophytes, such as Salicornia species, are promising new foods and are consumed for their pleasant salty taste and nutritional value. Since Salicornia is perishable, modified atmospheric packaging (MAP) can be a useful tool, in combination with proper temperature, to halt further quality degradation in this type of product. The purpose of this study was to investigate the effect of MAP, with or without refrigeration, to extend the shelf life of glasswort (Salicornia europaea L.) grown hydroponically (floating raft system) in a greenhouse with a nutrient solution containing 0 g/L (C) or 12.5 g/L of NaCl (T). The dry matter content, weight loss, respiration rate, biochemical composition, color, antioxidant capacity, and sensorial attributes were determined in shoots after harvest and during storage in plastic bags filled with technical air or with MAP at 4 or 20 °C for 120 h. At harvest, plants supplied with salt-enriched solution (T) showed a significant improvement in nutritional value and sensory profile. Storage in air at room temperature (20 °C) accelerated weight loss and diminished color stability, particularly in non-salinity samples (C), while MAP extended the shelf life of all the samples regardless of the storage temperature adopted. Optimal storage conditions were observed when MAP was combined with refrigeration, which allowed to effectively preserve shoots sensory acceptability for a period of about seven days. Future research could further explore the long-term effects on the nutritional value and sensory quality of S. europaea under various combinations of MAP and different storage temperatures ranging between 4 °C and 20 °C. [ABSTRACT FROM AUTHOR]

This study presents a reproducible and scalable method for synthesizing silica nanoparticles (SNPs) with controlled sizes below 200 nm, achieved by systematically varying three key reaction parameters: ammonium hydroxide concentration, water concentration, and temperature. SNPs with high monodispersity and controlled dimensions were produced by optimizing these factors. The results indicated a direct correlation between ammonium hydroxide concentration and particle size, while higher temperatures resulted in smaller particles with increased polydispersity. Water concentration also influenced particle size, with a quadratic relationship observed. This method provides a robust approach for tailoring SNP sizes, with significant implications for biomedical applications, particularly in drug delivery and diagnostics. Using eco-friendly solvents such as ethanol further enhances the sustainability and cost-effectiveness of the process. [ABSTRACT FROM AUTHOR]

During the γ phase–δ phase transition, U-50Zr fuel experiences spinodal decomposition, which has a significant effect on fuel properties. However, little is known about the spinodal decomposition of U-50Zr. The spinodal decomposition behavior in U-50Zr is studied in this research using the phase-field approach. The mechanism of spinodal decomposition from a thermodynamic perspective is studied, and the effects of temperature and grain boundary (GB) on spinodal decomposition are analyzed. It is found that the concentration of U atoms in the U-rich phase formed during spinodal decomposition is as high as 90%. The U-rich phase first appears at the GB position, and precipitation phases appear inside the grain later. Ostwald ripening occurs when larger precipitation phases on the GB absorb isolated smaller precipitation phases inside the grain. The coarsening rate of precipitation phases and the time it takes for spinodal decomposition to achieve equilibrium are both influenced by temperature. [ABSTRACT FROM AUTHOR]

Electropolishing is a widely used technique for polishing additive manufactured (AM) components, while complex internal surface polishing remains a challenge. In this study, we explore the use of ethaline as an electrolyte and investigate the effects of temperature, time, stirring speed, and voltage on the electropolishing effectiveness for AM tubes without pre-treatment through orthogonal experiments. The optimal combination of these factors is then applied in further electropolishing experiments on straight tubes with large length-to-diameter ratios and an angled tube. Our results indicate that temperature has the most significant impact on internal surface electropolishing performance, and other factors' effects are also analyzed. Ethaline can be a promising electrolyte for internal surface electropolishing of AM components because of its high viscosity, which is validated by flow field simulation of the hydrodynamic conditions inside the tubes. [ABSTRACT FROM AUTHOR]

Laser damage in films under long-term high-temperature conditions is a significant concern for advancing laser applications. This study focused on HfO2 films prepared using the sol–gel method with HfCl4 as a precursor. It examined the effects of temperature on various properties of the films, including their optical properties, microstructure, surface morphology, absorption, and laser-induced damage threshold (LIDT). The prepared film demonstrated desirable characteristics at the high temperature of 423 K, such as high transmittance, low absorption, and high LIDT. As the duration of its high-temperature exposure increased, the LIDT of the films gradually decreased. An intriguing finding was that the film's LIDT exhibited an exponential decay pattern with prolonged heating time. This observation could be attributed to the power-law increase in defects on both the internal and surface areas of the film as the duration of high-temperature exposure lengthened. Moreover, even after a 15-day heating period at 423 K, the film maintained an LIDT of 12.9 J/cm2, indicating its potential applicability in practical high-temperature environments. This study provided a general pattern and a universal formula for understanding the laser damage of sol–gel films at high temperatures over time. Furthermore, it opened possibilities for future developments of laser films suitable for extreme environments. [ABSTRACT FROM AUTHOR]

A self-degradable rubber plug (SDRP) was developed to address issues in existing crosslinked polymer temporary plugging technology, such as poor self-degradation properties. The synthesis formula was optimized using response surface analysis, resulting in an optimized composition of the SDRP: 13 wt% monomer, 0.02 wt% initiator, 0.7 wt% crosslinker, and 1.8 wt% degradation catalyst. Under the condition of 70–120 °C, the SDRP was transformed from a liquid to a solid gel in 30–110 min; the degradation time was 3–10 days, and the viscosity of the completely degraded solution was lower than 20 mPa·s. At an injection volume of 1 PV SDPR, a breakthrough pressure of 8.34 MPa was achieved. The hydrolysis of the unstable crosslinker was found to have caused the breakage of the SDRP. Over time, the functional groups within the unstable crosslinker underwent hydrolysis due to the combined effects of temperature and the degradation catalyst. This process led to the disruption of crosslinking points, resulting in a gradual deterioration of the network structure. As a consequence, some immobile water was converted into free water. The mobility of water molecules increased until the plug was completely degraded into a viscous liquid. This study enriches the temporary plugging gel system. [ABSTRACT FROM AUTHOR]

Huangjinya has recently seen widespread adoption in key tea-producing areas of China, celebrated for its unique varietal traits. Its leaves are also used to produce black tea with distinctive sensory characteristics. The fragrance-enhancing (EF) process is essential in crafting Huangjinya black tea (HJYBT) and is significant in flavor development. However, the impact of EF on non-volatile metabolites (NVMs), volatile metabolites (VMs), and their interactions remains poorly understood. This study aims to investigate how EF temperatures (60 °C, 70 °C, 80 °C, 90 °C, and 110 °C) influence HJYBT flavor transformation. Quantitative descriptive analysis revealed that EF improved the color, aroma, and appearance of tea leaves. Moreover, after an EF temperature of 80 °C, the HJYBT exhibited lower bitterness and astringency, whereas floral, sweet, and fruity aromas became stronger. However, when EF temperatures exceeded 90 °C, a pronounced burnt aroma developed, with HJYBT at 100 °C exhibiting caramel and roasted notes. Partial least squares discriminant analysis indicated that geraniol and linalool contribute to floral and fruity aromas, while 2-ethyl-6-methyl-pyrazine, furfural, and myrcene are key volatiles for caramel and roast aromas. Heptanal, methyl salicylate, α-citral, 1-hexanol, and (E)-3-hexen-1-ol were found to modify the green and grassy odor. Overall, HJYBT treated at 80 °C EF exhibited the highest umami, sweetness, floral and fruity aromas, and overall taste, exhibiting the least astringency, bitterness, and green and grassy notes. These results provide a significant theoretical basis for enhancing HJYBT quality and selecting the optimal EF method. [ABSTRACT FROM AUTHOR]

In order to analyze the effect of temperature changes on the shock initiation performance of HMX–based booster explosive, which consists of 95% HMX and 5% FPM2602 by weight, a temperature calibration test of acceptor was designed. The temperature changes in the booster at low and elevated temperatures under the constraint of steel sleeve were obtained. Based on the temperature calibration results, polymethyl methacrylate (PMMA) was selected as gap material to conduct a small scale gap test (SSGT) of HMX–based booster under different temperature conditions. The corresponding critical gap thickness was tested. Based on SSGT results at different temperatures, the shock initiation processes were simulated by adjusting parameters of ignition and growth reactive rate model. The critical gap thickness and critical initiation pressure of HMX–based booster at different temperatures were numerically predicted. By combining SSGT experimental data and simulation results, the attenuation law and fitting prediction formula of the critical initiation pressure of HMX–based booster were proposed. The mechanism of temperature effect on the shock sensitivity of HMX–based booster explosive was analyzed. The research results indicate that the critical gap thickness of HMX–based booster gradually increases with the rise in temperature, and the critical initiation pressure gradually decreases during the shock initiation process under the heating temperature conditions. In addition, the simulation results show that the heated HMX–based booster under steel constraints becomes more sensitive at high temperatures (>120 °C), while the cooled booster is more insensitive, but its critical initial pressure does not change significantly between 88 °C and 120 °C. The experimental and numerical prediction results are important for the shock initiation safety and design of an insensitive booster explosive. [ABSTRACT FROM AUTHOR]

High-speed ballistic impact tests were conducted at room temperature and 500 °C on nickel-based superalloy GH4169 simulated blade specimens containing leading-edge features. The microscopic characteristics of the impact notch at room temperature versus 500 °C were observed by electron backscatter diffraction (EBSD), and it was found that the grains on the notched subsurface were ruined, while in more distant regions, the impact energy was mainly absorbed by grain boundaries. Internal damage is more concentrated in the notched subsurface region at 500 °C compared to room temperature. The high cycle fatigue strength of the damaged specimens under different conditions was tested. The results showed that the high cycle fatigue strength of the damaged specimens increased with the increase in the notch depth, and the fatigue strength of the damaged specimens at 500 °C was higher than the fatigue strength at room temperature. Both the 48 h post-impact holding time at 500 °C and the preload during impact at 500 °C increased the fatigue strength of the damaged specimens. [ABSTRACT FROM AUTHOR]

Fluidity tests of 99.9%Al and 99.7%Al were conducted using a die casting machine equipped with a spiral die with a channel gap of 0.5 mm. The effects of die temperature and plunger speed on the fluidity were investigated. To clarify the flow length for these alloys, ADC12 and Al-X%Fe (X ≤ 1.1) were also cast. A 1.0 mm channel gap was also used to compare the fluidity in a wider gap. The fluidity of 99.9%Al and 99.7%Al at a die temperature of 30 °C and a plunger speed of 0.2 m/s was superior to that at 150 °C and 0.8 m/s when the channel gap was 0.5 mm, and similar results were found for ADC12 and Al-X%Fe. When the die temperature was 30 °C, the fluidity of 99.9%Al and 99.7%Al decreased as the plunger speed increased when the channel gap was 0.5 mm, and similar results were also found for ADC12 and Al-X%Fe. These results did not align with conventional expectations. A discussion of the results based on the peeling and re-melting of the solidified layer was provided. [ABSTRACT FROM AUTHOR]

As eco-friendly complexes develop, interest in eco-friendly facilities is also growing. Particularly, rainwater harvesting facilities have demonstrated positive effects by reducing runoff to mitigate urban flooding and recycling water for landscaping and cleaning purposes. In this study, we analyzed the quality of stored rainwater, which has improved by excluding initial runoff, and examined the temperature reduction effects of road sprinkling and mist spraying. Road sprinkling decreased the temperature of asphalt and permeable pavements by approximately 15 °C, with permeable pavements maintaining the reduced temperature for a longer time. The indoor experiments with mist spraying showed a temperature reduction effect of 3.4 °C. The quality analysis of the rainwater harvesting facilities revealed that the water quality was suitable for irrigation and landscaping by excluding the initial runoff. This study confirms the effectiveness of rainwater utilization in mitigating urban heat islands and improving water circulation within cities. [ABSTRACT FROM AUTHOR]

Based on an analysis of the extant literature, this paper summarizes the research progress on the mechanical properties and long-term behavior of corrugated steel web (CSW) box girder bridges. First, the research results of CSW box girder bridges in terms of the shear buckling performance (local shear buckling, overall shear buckling, and interaction buckling), bending performance, bending capacity, torsional capacity, and coefficient of internal force increase are summarized, along with the main factors affecting the mechanical performance of CSW box girder bridges. Second, based on research on the self-oscillation characteristics and dynamic response of CSW box girder bridges, the influence of structural parameters on the self-oscillation characteristics is analyzed. Finally, the long-term mechanical behavior of the CSW box girder bridges is analyzed in terms of fatigue, creep, and temperature effects. The existing research results demonstrate that there still exist deficiencies in the mechanical properties and long-term behavior of CSW box girder bridges, and this paper thus suggests a future research focus on CSW box girder bridges to provide a reference for further improving their basic theoretical system. [ABSTRACT FROM AUTHOR]

The addition of flexible Cu2ZnSnS4 (CZTS) thin film solar cells to titanium (Ti) substrates is an attractive way to achieve the low-cost manufacturing of photovoltaics. Prior research has indicated that the appropriate diffusion of Ti elements can enhance the crystalline growth of CZTS films. However, the excessive diffusion of Ti has been shown to adversely affect the photovoltaic performance of CZTS photovoltaic devices. Therefore, it is essential to regulate the diffusion of Ti elements within CZTS thin films to optimize their photovoltaic properties. The tendency for Ti substrate elements to diffuse into CZTS films is also influenced by the activation energy associated with these Ti elements. The sulfurization temperature is posited to be a critical factor in modulating the diffusion and activation energy of Ti elements within CZTS thin films. Consequently, this research investigates the alteration of the sulfurization temperature of CZTS thin films in order to enhance the properties of these thin films and to examine the diffusion behavior of titanium elements. The results reveal that as the sulfurization temperature increases, the diffusion of Ti elements within the CZTS thin films initially increases, then decreases, and subsequently increases again. This pattern suggests that the diffusion of Ti elements is affected not only by the activation energy of the Ti elements but also by the defect hopping distance within the CZTS thin films. Notably, at a sulfurization temperature of 550 °C, the grains at the base of the CZTS thin film demonstrate an increased density, which is associated with a reduced defect hopping distance, thereby hindering the diffusion of Ti elements within the CZTS thin films. Furthermore, at this specific sulfurization temperature, the slope of the current–voltage (I–V) curve for the CZTS/Ti structure reaches its maximum, indicating optimal ohmic contact characteristics. [ABSTRACT FROM AUTHOR]

In this study, the effect of the pre-infiltration temperature (Ti) on the liquid-phase infiltration characteristics and its effect on the magnetic properties of single-domain GdBCO bulks prepared by the top-seeded infiltration growth (TSIG) method are comprehensively investigated. The results reveal that (1) the liquid Ba-Cu-O phase (LP) did not uniformly infiltrate into the Gd2BaCuO5 (Gd-211) solid-phase pellet (SPP). (2) The initial melting and infiltration of the LP occurred at approximately 920 °C. The average infiltration depth and amount of LP that infiltrated the SPP increased with increasing Ti accompanied by the shrinkage and depletion of the LP pellet. (3) The LP penetrated up to the top surface of the SPP and uniformly infiltrated throughout the SPP when the Ti was approximately 960 °C and 1020 °C, respectively. (4) The mean Gd-211 particle size of the pre-infiltrated SPP increased from 1.94 µm at 920 °C to 2.52 µm at 1040 °C as the Ti rose. (5) The magnetic properties and microstructure of the single-domain GdBCO bulks were significantly influenced by the microstructure of the pre-infiltrated SPP. The largest levitation force of 35.64 N and trapped field of 0.23 T were obtained in the single-domain GdBCO bulks at an infiltration Ti of 960 °C. [ABSTRACT FROM AUTHOR]

Coatings are essential for protecting steel structures from corrosion and mechanical stresses, especially under challenging environmental conditions. To this end, this study systematically examines the effects of temperature (−20 °C to 50 °C), strain rate (6.67 × 10−4 s−1 to 1.67 × 10−2 s−1), and intermediate coat thickness (140 μm to 700 μm, the layer between the primer and topcoat) on the uniaxial tensile properties of heavy-duty coatings for steel structures. Experimental and theoretical analyses were conducted to quantitatively assess the influence of these factors on the mechanical properties of the coatings. A multifactor constitutive model was developed based on the Sherwood–Frost model by integrating material characteristics and fitting experimental data, incorporating response functions for temperature, strain rate, and intermediate coat thickness. The results reveal that increased temperature causes temperature-induced softening, while higher strain rates lead to strain rate-dependent strengthening of the coatings. In contrast, the effect of layer thickness on mechanical properties follows a non-monotonic trend, influenced by the structural and material characteristics of the coatings, with the most significant mechanical response occurring at 560 μm thickness. These findings suggest that optimal coating design must consider multiple factors to enhance mechanical performance. Additionally, the correlation coefficients (r) between the model predictions and experimental results are 0.97 or higher, indicating the model's effectiveness in predicting and optimizing the mechanical performance of heavy-duty coatings under complex conditions. [ABSTRACT FROM AUTHOR]

Although the addition of buffers provides improved stability to flucloxacillin (FLU) solutions, unbuffered solutions are often preferred in clinical practice. The first purpose of this study was to investigate whether a 50 mg/mL solution of FLU in normal saline is stable for 24 h at 33 °C so that it can be applied for outpatient parenteral antimicrobial therapy (OPAT) using portable elastomeric infusion pumps (PEIPs). When the PEIPs were stored in an oven at 33 °C and deflated over 24 h, the volume of the collected solution, pH, and FLU concentration were checked every 4 h. Obtaining better results than expected based on the literature data, other storage conditions, such as refrigeration, room temperature (RT), 37 °C, refrigeration followed by 24 h at 33 °C and 37 °C, and different batches/brands, were also tested. This study confirmed the pronounced effect of temperature on the stability of FLU and also showed the relationship between the stability of FLU and the initial pH of the solution. FLU was quite stable at refrigeration and RT conditions, with more than 99% and 95% remaining. After 24 h at 33 °C, more than 92% of FLU was still present in the solution, while this number decreased to less than 85% when the storage temperature reached 37 °C. The remaining percentage was found to be even lower when the solution was stored at 2–8 °C for 6 days, followed by 24 h storage at 33 °C or 37 °C, with losses of 17% and 30%, respectively. The stability of FLU became worse when the initial pH of the solution was lower than 5.9 since the concentration of FLU dropped to less than 90% after 24 h at 33 °C, and a precipitate started to form when the initial pH of the solution was around 5.3. Therefore, FLU in PEIPs could be employed for 24 h if the temperature was ideally not more than 33 °C, while the pH should be not less than 5.9 upon reconstituting the FLU solution. [ABSTRACT FROM AUTHOR]

Background: The dramatic temperature fluctuations spurred by global warming and the accompanying extreme weather events inhibit mango growth and threaten mango productivity. Particularly, mango flowering is highly sensitive to temperature changes. The mango fruit setting rate was significantly positively correlated with pollen activity, and pollen activity was regulated by different metabolites. Methods: In this study, the in vitro pollen of two mango varieties ('Renong No.1' and 'Jinhuang'), in which sensitivity to temperature differed significantly, were subjected to different temperature stresses (15 °C, 25 °C and 35 °C), and their metabolomics were analyzed. Results: The present results showed that 775 differential metabolites were screened by liquid chromatography–mass spectrometry and divided into 12 categories. The two varieties had significant differences in metabolite expression under different temperature stresses and the effect of low temperature on 'Renong No.1' mainly focused on amino acid metabolism, while the effect on 'Jinhuang' was mainly related to glycolysis. However, under the 35 °C temperature stress, 'Renong No.1' responded by redistributing riboflavin and betaine in vivo and the most obvious metabolic pathway of 'Jinhuang' enrichment was pyrimidine metabolism, which had undergone complex main body formation and extensive regulatory processes. The changes of metabolites of different varieties under low temperature and high temperature stress were different. Among them, flavonoids or flavonoid derivatives were included in class A (216 metabolites), C (163 metabolites) and D (233 metabolites) metabolites, indicating that flavonoid metabolites had an obvious regulatory effect on mango pollen metabolism under different temperature stress. Conclusions: The present results provide valuable information for reproductive biology studies and breeding in mango, in particular, the selection and breeding of the most suitable varieties for different production areas. [ABSTRACT FROM AUTHOR]

In order to achieve batch production, we propose a simple and fast method to prepare leather-finished plywood. In this study, ethylene–vinyl acetate was selected as the intermediate layer to prepare EVA/polyurethane (PU) leather composites. ESEM, tensile property test and compressive property test were used to characterize the microstructure and physical-mechanical properties of the composites. The response surface method (RSM) was also used to explore the relationship between hot pressing temperature, hot pressing pressure and hot pressing time. The significance of the factors and the interactions between the two factors were determined by ANOVA, with the most significant effect being that of the temperature. The theoretical optimal hot pressing process conditions were calculated by the regression equation as a temperature of 124.4 °C, a time of 200 s and a pressure of 1.3 MPa. The surface bond strength of the test specimen measured under this condition was 1.89 MPa, it has good finishing properties and the impregnation peel strength and surface bond strength met the requirements of GB/T 15104-2021. [ABSTRACT FROM AUTHOR]

In recent years, large power batteries have been widely used not only in automobiles and other vehicles but also in maritime vessels. The thermal uniformity of large marine battery packs significantly affects the performance, safety, and longevity of the electric ship. As a result, the thermal management of large power batteries has become a crucial technical challenge with traditional battery management system (BMS) that cannot effectively solve the battery heating problem caused by electrochemical reactions and joule heating during operation. To address this gap, a battery thermal management system (BTMS) has been newly designed. This article presents the design of a large marine battery pack, which features a liquid cooling system integrated into both the bottom and side plates of each pack. The flow plate is constructed from five independent units, each connected by manifold structures at both ends. These connections ensure the formation of a stable and cohesive flow plate assembly. Although research on the BTMS is relatively advanced, there is a notable lack of studies examining the effects of liquid temperature, flow rate, and battery discharge rate on the temperature consistency and uniformity of large marine battery packs. This work seeks to design the cooling system for the battery pack and analyzes the impact of the temperature, flow rate, and battery discharge rate of the liquid fluid on the consistency and uniformity of the battery pack temperature on the overall structure of the battery pack. It was found that, in low discharge conditions, there was good temperature consistency between the battery packs and between the different batteries within the battery pack, and the temperature difference did not exceed 1 °C. However, under high discharge rates, a C-rate of 4C, there might have been a decrease in temperature consistency; the temperature rise rate even exceeded 50% compared to when the discharge rate was low. The flow rate in the liquid flow characteristics had little effect on the temperature consistency between the batteries and the temperature uniformity on the battery surface, and the temperature fluctuation was maintained within 1 °C. Conversely, the liquid flow temperature had little effect on the temperature distribution between the batteries, but it caused discrepancies in the surface temperature of the batteries. In addition, the liquid flow temperature could cause the overall temperature of the battery to increase or decrease, which also occurs under different discharge rates. [ABSTRACT FROM AUTHOR]

Understanding the extraction process of Nigella oil is crucial due to its significant impact on yield, quality, and therapeutic effectiveness. This study explored the effects of various screw press temperatures (40 °C, 50 °C, 60 °C, 70 °C, and 80 °C) on the quantity and quality of Nigella oil to optimize conditions that maximize yield while maintaining its nutritional and therapeutic attributes. Our findings indicate a linear increase in oil yield as screw press temperatures rose from 40 °C to 80 °C. There were no significant differences observed in total phenolic content (TPC), cupric reducing antioxidant capacity (CUPRAC), or the composition and ratio of fatty acids across oils extracted at different temperatures. However, the ferric-reducing antioxidant power (FRAP) was highest in oils extracted at 60 °C, while the thymoquinone (TQ) content peaked between 40 °C and 60 °C. These results underscore the importance of optimizing screw press temperatures to strike a balance between maximizing oil yield and preserving its valuable therapeutic and nutritional properties [ABSTRACT FROM AUTHOR]

Seedling growth is one of the most important stages for the establishment of natural and artificial regeneration. For the first time, the initial growth and biomass allocation of seedlings germinated from cryostored seeds of Parkia nitida were analyzed. P. nitida is an economically and ecologically important timber tree species distributed in Central and South America. Cryostored seeds germinated quickly after priming by scarifying a part of the seedcoat with emery paper, reaching a germination percentage of 94%. Thirteen weeks after germination, the seedlings grew to a height of 16.5 to 60.0 cm. The results of our study, under different day/night alternating culture temperatures, showed that culture temperature had a direct correlation with seedling growth, total biomass allocation, and biomass partitioning. The greatest growth (height, diameter, and number of node sections) and greatest biomass allocation (leaf, stem, and root weight) were recorded under alternating temperatures of 30/25 °C, and these decreased with decreasing culture temperatures to 25/20 °C and 20/15 °C. Shoot:Root (S:R) ratios also decreased with decreasing culture temperatures, but a statistically significant difference (p < 0.05) was only observed between 20/15 °C and 30/25 °C. However, significant differences were not observed in Photosynthetic:Non-photosynthetic organ ratios among the different alternating culture temperatures. This study provides fundamental information for the production of good-quality seedlings of the fast-growing tropical trees of the legume family. [ABSTRACT FROM AUTHOR]

The present study analyzed the effect of temperature, pH, pre-treatment and mixing ratio on the anaerobic digestion process. The parameters during the anaerobic co-digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA was carried out to find the significant parameters which influence biogas production. Experimental tests were carried out at laboratory-scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic performance (SMP) during anaerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate, and was validated with the literature. The improvement of biogas production with different pre-treatments, i.e., ultrasonic, autoclave, and microwave techniques, was also analyzed. The results showed that the reactor that was maintained at 35 °C showed the highest biogas production, while the reactor that was maintained at a lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas production increases. Methanogenic activities of microorganisms were reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27% when the substrates were treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co-digestion of food waste and cow manure is a temperature of 35 °C, a pH of 7 and a mixing ratio (CM:FW = 1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio. [ABSTRACT FROM AUTHOR]

The temperature response of pavement is not only crucial for assessing the internal stresses within pavement structures but is also an essential parameter in pavement design. Investigating the temperature response of rubberized concrete pavements (RCP) can support the construction of large-scale rubber concrete pavements. This study constructed a pavement monitoring system based on fiber Bragg grating technology to investigate the temperature distribution, temperature strain, temperature effects, and temperature stress of RCP. The results show that the daily temperature–time history curves of concrete pavement exhibit a significant asymmetry, with the heating phase accounting for only one-third of the curve. The temperature at the middle of RCP is 1.8 °C higher than that of ordinary concrete pavement (OCP). The temperature distribution along the thickness of the pavement follows a "spindle-shaped" pattern, with higher temperatures in the center and lower temperatures at the ends. Additionally, the addition of rubber aggregates increases the temperature strain in the pavements, makes the temperature–strain hysteresis effect more pronounced, and increases the curvature of the pavement slab. However, the daily stress range at the bottom of RCP is approximately 0.7 times that of OCP. [ABSTRACT FROM AUTHOR]

This paper delved into the thermal dynamics and stability of Wireless Power Transfer (WPT) systems, with a focus on the temperature effects on the coil structure. Using the Finite Element Method (FEM), this study investigated both unidirectional and bidirectional coupling field simulations, assessing their impacts on the transmission efficiency of LCL-resonant WPT systems. The boundary conditions and processes of the electromagnetic–thermal coupling field related to coil loss were analyzed, as well as the dynamic thermal balance in the bidirectional coupling field model. It was found that there is a significant temperature variation across the coil, with the highest temperatures at the central position and the lowest at the edges. This temperature rise notably changed the electrical parameters of the system, leading to variations in its operating state and a reduction in transmission efficiency. A constant coil voltage control strategy was more effective in mitigating the temperature rise compared to a constant coil current strategy, providing valuable insight for enhancing the efficiency and stability of WPT systems. [ABSTRACT FROM AUTHOR]

The use of environmentally friendly hydraulic fluids is frequently influenced by the temperature reached in the hydraulic circuit. This paper presents an analysis of the effect of temperature on the lifetime of the hydraulic fluid and the hydraulic pump. The test was carried out by continuous loading with a pressure of 21 MPa and a temperature of 96 °C for 100 h. A pressure valve was used for the continuous loading and the temperature was maintained using a cooler. At intervals of 25 h, the flow characteristics of the hydraulic pump were measured and oil sampling was carried out. Subsequently, a comprehensive chemical and physical analysis was carried out. In the present paper, a comprehensive analysis of the influence of eco-friendly hydraulic fluid on the operation of a gear hydraulic pump has been carried out. The study itself did not show the negative influence of the eco-friendly hydraulic fluid on the operation of the gear hydraulic pump. It can be expected that the results of the study will enable the use of eco-friendly hydraulic fluids in environmentally sensitive areas. [ABSTRACT FROM AUTHOR]

Hot stamping is a forming process widely used in the manufacturing of structural components in automobiles. It is a versatile process that enables the fabrication of complex-shaped components with high strength. It also facilitates the manufacturing of components that incorporate high-strength sections and high-ductility sections, by controlling the cooling rate. The process is versatile in terms of the microstructures and mechanical properties that can be obtained. This versatility, however, puts high demands on the materials pertaining their stability, wear resistance, costs, etc. This study has focused on understanding the effect of temperature on the tribological response of different tool materials when these are exposed to high temperatures. The results show that friction significantly stabilises with increased temperature for most tool steels. One tool steel behaves more unstably at high temperature, and this is attributed to the presence of Cr7C3, MoO3, and VO and severe wear on the workpiece material. The most severe wear on the workpiece is caused by a partially melted interdiffusion layer, which facilitates the detachment of the Al-Si coating and subsequent transfer onto the tool; this effect is maximised at the highest temperatures of the workpiece. An important finding is that friction and material transfer severity decrease as the workpiece temperature decreases, and friction is stabilised as tool temperature increases without minimising wear or the average friction coefficient. [ABSTRACT FROM AUTHOR]

Macroalgal biomass blooms, including those causing the green and golden tides, have been rising along Chinese coasts, resulting in considerable social impacts and economic losses. To understand the links between the ongoing climate changes (ocean warming and acidification) and algal tide formation, the effects of temperature (20 and 24 °C), pCO2 concentration (Partial Pressure of Carbon Dioxide, 410 ppm and 1000 ppm) and their interaction on the growth of Ulva prolifera and Ulva lactuca (green tide forming species), as well as Sargassum horneri (golden tide forming species) were investigated. The results indicate that the concurrent rises in temperature and pCO2 level significantly boosted the growth and nutrient uptake rates of U. lactuca. For U. prolifera, the heightened growth and photosynthetic efficiency under higher CO2 conditions are likely due to the increased availability of inorganic carbon. In contrast, S. horneri exhibited negligible responsiveness to the individual and combined effects of the increased temperature and CO2 concentration. These outcomes indicate that the progressive climate changes, characterized by ocean warming and acidification, are likely to escalate the incidence of green tides caused by Ulva species, whereas they are not anticipated to precipitate golden tides. [ABSTRACT FROM AUTHOR]

The Hubao–Egyu Urban Agglomeration (HBEY) was a crucial ecological barrier in northern China. To accurately assess the impact of climate change on vegetation growth, it is essential to consider the effects of time lag and accumulation. In this study, we used a newly proposed kernel Normalized Difference Vegetation Index (kNDVI) as the metric for vegetation condition, and employed partial correlation analysis to ascertain the lag and accumulation period of vegetation response to climate by considering different scenarios (No/Lag/Acc/LagAcc) and various combinations. Moreover, we further modified the traditional residual analysis model. The results are as follows: (1) From 2000 to 2022, the HBEY experienced extensive and persistent greening, with a kNDVI slope of 0.0163/decade. Precipitation was identified as the dominant climatic factor influencing vegetation dynamics. (2) In HBEY, the lag effect of temperature was most distinct, particularly affecting the vegetation in cropland and grassland. The accumulation effect of precipitation was pronounced in grassland. (3) Incorporating lag and accumulation effects into models increases the explanatory power of climate impacts on vegetation dynamics by 6.95% compared to traditional residual models. Our findings hold essential implications for regional ecological regulation and climate change response research. [ABSTRACT FROM AUTHOR]

In this study, a steady-state thermodynamic equilibrium evaluation of CO2 methanation was conducted. Calculations were performed by solving the material balance equations using the equilibrium constants of CO2 methanation and reverse water–gas shift reactions. Results obtained from an analytical method developed with the aid of the Microsoft Excel platform were compared to simulations conducted using the commercially available free software COCO and DWSIM. The effects of temperature, pressure, and H2/CO2 ratio on CH4 yield, carbon oxide formation, and heat balance were investigated. The results indicate that the methanation process is highly favored by low temperatures and higher pressures with a stoichiometric H2/CO2 ratio. Under these conditions, CH4 output increases, and carbon formation is reduced, resulting in better performance. Simulations from all three models are in agreement, with minor differences noted in the DWSIM software. [ABSTRACT FROM AUTHOR]

There is a lack of information about transforming growth factor beta-1 (TGF-β1) and cytokines contained in pure platelet-rich plasma (P-PRP) and release from pure-platelet-rich gel supernatants (P-PRGS) might be affected by the temperature and time factors; P-PRP from 6 heifers was activated with calcium gluconate. Thereafter, P-PRG and their supernatants (P-PRGS) were maintained at −80, −20, 4, 21, and 37 °C and collected at 3, 6, 12, 24, 48, 96, 144, 192, 240, and 280 h for subsequent determination of TGF-β1, tumor necrosis factor alfa (TNF-α), interleukin (IL)-2, and IL-6; TGF-β1 concentrations were significantly (p < 0.05) higher in PRGS maintained at 21 and 37 °C when compared to PRGS maintained at 4, −20, and −80 °C; PRGS TNF-α concentrations were not influenced by temperature and time factors. However, PRGS maintained at 4 °C showed significantly (p < 0.05) higher concentrations when compared to PRGS maintained at −20, and −80 °C at 144, and 192 h. IL-6 concentrations were significantly (p < 0.05) higher in PRGS stored at −20, and −80 over the first 48 h and at 10 days when compared to PRGS stored at 4, 21, and 37 °C. These results could suggest that P-PRP/P-PRGS could be maintained and well preserved for at least 12 days at room temperature for clinical use in bovine therapeutic massive protocols. [ABSTRACT FROM AUTHOR]

Due to its excellent electrical performance, mechanical reliability, and thermal stability, electroplated gold is still the most commonly used material for movable beams in RF MEMS switches. This paper investigates the influence of process conditions on the quality and growth rate of gold electroplating, and the optimized process parameters for the gold electroplating process are obtained. The characterization of the optimized electroplated gold layer shows that it has small surface roughness and excellent thermal stability. With this optimized gold electroplating process, the RF MEMS switches are fabricated and hermetic packaged. In order to obtain the temperature environment adaptability of the packaged switch, the influence of working temperature is studied. The temperature effects on mechanical performance (includes pull-in voltage and lifetime) and RF performance (includes insertion loss and isolation) are revealed. [ABSTRACT FROM AUTHOR]

Accurately predicting the adsorbed gas content in coal reservoirs is crucial for evaluating the gas content in deep coal seams. However, due to the significant variations in temperature and pressure conditions across different coal reservoirs, accurately assessing the adsorbed gas quantity presents challenges. Based on the adsorption potential theory, this paper proposes a prediction model of adsorbed gas that is applicable under various temperature and pressure conditions. The results indicate that the adsorbed gas content in deep coal reservoirs is influenced by a combination of temperature, pressure, and coal rank. The increase in pressure and coal rank enhances the inhibitory effect of temperature on methane adsorption. Meanwhile, there are significant differences in the results obtained from various virtual saturated vapor pressure models. Among them, the Amankwah model theoretically satisfies the uniqueness of the adsorption characteristic curve, with the optimal k values for different coal rank samples ranging between 2 and 9. In terms of predicting the adsorption gas, the performance of the models is ranked as follows: Amankwah model > Antonie model > Astakhov model > Dubinin model > Reid model. The Amankwah model exhibits the smallest average relative error and root mean square error. In addition, as burial depth increases, the influence of the pressure on methane adsorption decreases, while the significance of temperature increases, with the critical depth located around 1600 m. At depths shallower than the critical depth, adsorbed gas tends to preferentially accumulate and form reservoirs, which generally have lower commercial value. At depths deeper than the critical depth, free gas has the potential to form reservoirs. At this stage, gas reservoirs dominated by adsorbed gas start transitioning to those containing free gas. These findings are expected to deepen the understanding of deep coalbed methane and provide a scientific basis for exploration and development in the study area. [ABSTRACT FROM AUTHOR]

This study aims to evaluate the effectiveness of inactivating Salmonella enteritidis in fresh chicken breast by irradiation using a combination of short-wave UV (0, 3, 6, 9, 12, and 15 J/cm2) and a natural antimicrobial such as caffeine (0, 5, 10, 15, and 20 nM/g) at 14 °C as alternative proposals to conventional techniques to reduce pathogens in food. The effect of temperature was studied in an initial phase (2 to 22 °C). The most suitable models were double Weibull in 60% of cases, with an adjustment of R2 0.9903–0.9553, and Weibull + tail in 46.67%, with an adjustment of R2 of 0.9998–0.9981. The most effective combination for the reduction in Salmonella was 12 J/cm2 of UV light and 15 nM/g of caffeine, with a reduction of 6 CFU/g and an inactivation rate of 0.72. The synergistic effect was observed by increasing caffeine and UV light. Furthermore, the physico-chemical characteristics of the food matrix were not affected by the combination of both technologies. Therefore, these results suggest that this combination can be used in the food industry to effectively inactivate Salmonella enteritidis without deteriorating product quality. [ABSTRACT FROM AUTHOR]

In this study, the radio frequency vacuum drying (RFVD) technique was used to dry Codonopsis pilosula slices. The effects of the drying temperature, slice thickness, plate spacing, and vacuum degree on the drying characteristics and physicochemical properties of the slices were investigated. The results showed that as the drying temperature and vacuum degree increased and the slice thickness and plate distance decreased, the drying rate and effective moisture diffusion coefficient of the Codonopsis pilosula slices improved, and the required drying time was shortened by 11.11% to 29.41% compared to that after hot air drying (HAD). Through comparison, it was found that the Midilli and Weibull models could better describe the moisture variation trend during the RFVD of Codonopsis pilosula. After RFVD, the retention of lobetyolin and syringin in Codonopsis pilosula significantly increased, with maximum contents of 135.74 mg/100 g and 19.16 mg/100 g respectively, which were 75.2% and 124.28% higher than those obtained by HAD. The contents of polysaccharides, total phenolics, and total flavonoids and antioxidant performance were also enhanced. The color, shrinkage rate, and internal tissue structure were significantly improved. In conclusion, RFVD not only increases the drying speed of Codonopsis pilosula slices but also ensures the good quality of the dried products. [ABSTRACT FROM AUTHOR]

High-manganese steel (high-Mn) is valuable for its excellent mechanical properties in cryogenic environments, making it essential to understand its deformation behavior at extremely low temperatures. The deformation behavior of high-Mn steels at extremely low temperatures depends on the stacking fault energy (SFE) that can lead to the formation of deformation twins or transform to ε-martensite or α′-martensite as the temperature decreases. In this study, submerged arc welding (SAW) was applied to fabricate thick pipes for cryogenic industry applications, but it may cause problems such as an uneven distribution of manganese (Mn) and a large weldment. To address these issues, post-weld heat treatment (PWHT) is performed to achieve a homogeneous microstructure, enhance mechanical properties, and reduce residual stress. It was found that the difference in Mn content between the dendrite and interdendritic regions was reduced after PWHT, and the SFE was calculated. At cryogenic temperatures, the SFE decreased below 20 mJ/m2, indicating the martensitic transformation region. Furthermore, an examination of the deformation behavior of welded high-Mn steels was conducted. This study revealed that the tensile deformed, as-welded specimens exhibited ε and α′-martensite transformations at cryogenic temperatures. However, the heat-treated specimens did not undergo α′-martensite transformations. Moreover, regardless of whether the specimens were subjected to Charpy impact deformation before or after heat treatment, ε and α′-martensite transformations did not occur. [ABSTRACT FROM AUTHOR]

This study uses a sigmoidal function to describe the plastic strain hardening of metallic materials, considering temperature and strain rate effects. The effectiveness of this approach is evaluated and systematically compared with other hardening laws. Incorporating temperature and strain rate effects into the parameters of this sigmoidal-type hardening law enables a more precise description and prediction of the plastic deformation of materials under different combinations of temperature and strain rate. The temperature effect is coupled using a simplified Arrhenius model, and the strain rate effect is coupled with a modified Johnson–Cook model. The sigmoidal-type hardening law is integrated with an asymmetric yield criterion to address complex behavior, such as anisotropy and strength differential effects. The calibration and validation of the constitutive model involve examining uniaxial tensile/compressive flow curves in various directions and biaxial tensile/compressive flow curves for diverse metallic alloys, proving the proposed model's broad applicability. [ABSTRACT FROM AUTHOR]

The presence of the odorant 2-methylisoborneol (2-MIB) in drinking water sources is undesirable. Although 2-MIB production is known to be influenced by temperature, its regulation at the gene level and its relationship with Chlorophyll-a (Chl-a) at different temperatures remain unclear. This study investigates the impact of temperature on 2-MIB production and related gene expression in Pseudanabaena strains PD34 and PD35 isolated from Lake Paldang, South Korea. The strains were cultured at three temperatures (15, 25, and 30 °C) to examine cell growth, 2-MIB production, and mic gene expression levels. 2-MIB production per cell increased with higher temperatures, whereas mic gene expression levels were higher at lower temperatures, indicating a complex regulatory mechanism involving post-transcriptional and enzyme kinetics factors. Additionally, the relationship between Chl-a and 2-MIB involved in metabolic competition was analyzed, suggesting that high temperatures appear to favor 2-MIB synthesis more than Chl-a synthesis. The distinct difference in the total amount of the two products and the proportion of 2-MIB between the two strains partially explains the variations in 2-MIB production. These findings highlight the significant effect of temperature on 2-MIB biosynthesis in Pseudanabaena and provide a valuable background for gene data-based approaches to manage issues regarding 2-MIB in aquatic environments. [ABSTRACT FROM AUTHOR]

Aiming at the problems of large capacity, narrow transverse width, large excitation, high safety level, and difficulty in accurately grasping the working state of the cable-stayed bridge for the long-span track, this research obtains the structural response data in real time by establishing a health monitoring system. The adaptive filtering method was employed to separate the train load response and the temperature load response. Then, a train load effect analysis method based on the influence line and a temperature load effect analysis method based on the correlation were proposed to assess the operational status of the bridge in real time and objectively. The Chongqing Nanjimen Railway Track Bridge (hereinafter Chongqing Nanjimen track bridge) project was utilized as a case study to demonstrate the application of these methods. The results show that the adaptive filtering method can effectively separate the response of train and temperature loads. The normalized cross-correlation (NCC) results of the measured train load response and the influence line's finite element calculation show a high degree of fit between the measured values and the theory, proving that no significant anomalies are found in the bridge. There is a strong correlation between the ambient temperature difference and the Pearson correlation coefficient of structural response, which indicates that the Chongqing Nanjimen track bridge is currently in normal working condition. [ABSTRACT FROM AUTHOR]

The final feedwater temperature is the temperature of the feedwater supplied to the boiler in the power plant applied with the Rankine cycle. In thermal power plants adopting a regenerative cycle, it is generally known that the heat transfer of the boiler is reduced, and the efficiency of the power plant is increased. However, the output of the power plant is reduced when the final feedwater temperature is increased. In this study, the net output and efficiency of the power plants depending on the final feedwater temperature under the condition of constant boiler heat transfer rate were analyzed for five cases. The results show that there is a final feedwater temperature at which the net output and the net efficiency are maximized. The additional output of the power plant obtained by increasing the final feedwater temperature has the effect of reducing CO2 emissions. If the final feed water temperature is below 308.3 °C, the net output and the final feed water temperature are proportional for all cases. When the final feedwater temperature increases by 1 °C, the net output increases by 63.02 kW and CO2 emissions are reduced by 60.52 kgCO2/h on average. [ABSTRACT FROM AUTHOR]

Formic acid is a promising candidate fuel that can be produced by reacting renewable hydrogen with carbon dioxide. However, the burning safety characteristics of formic acid–air mixtures have not been fully studied. This paper presents an extensive theoretical study of the adiabatic explosion pressure of formic acid–air premixed laminar flames at various initial conditions (composition of formic acid: 17–38% volume; initial pressure: 0.1–1.5 bar; initial temperature: 333–500 K), using the GASEQ software package. GASEQ software calculates chemical equilibria based on ideal gas behavior and is based on the hypothesis of adiabatic expansion inside a closed containment that allows ideal expansion. The influence of the initial conditions (pressure, temperature, and concentration) of formic acid–air mixtures on the adiabatic explosion pressures, maximum flame temperature, and peak concentrations of the main reaction intermediates is investigated and discussed. It is found that the adiabatic peak explosion pressure (calculated equilibrium pressure) of the studied concentrations decreases with increasing initial temperature and increases linearly with increasing initial pressure. [ABSTRACT FROM AUTHOR]