Search

In this study, the focus is on the magnetic path formation and its effects on the performance of a counter-rotating dual-rotor permanent-magnet flux-switching machine (CR-DRPMFSM) for direct-drive counter-rotating wind power generation, based on different stator slot and rotor pole combinations. To fully exploit rotor-shaft bore and improve fault-tolerant design, as well as increase torque density, dual-rotor topologies with the capability for dual electrical and dual mechanical ports are investigated. Moreover, the direct-drive counter-rotating wind power generation technique offers a brushless topology, thus reducing maintenance cost and improving energy conversion efficiency compared to single-blade wind turbine systems. Using finite element analysis (FEA), the inherent magnetic coupling of the series and parallel paths shows varied impacts on the electromagnetic performance of four different CR-DRPMFSMs based on the slot/pole combinations (MI to MIV) considered in this study. The key electromagnetic performance indices, such as torque, cogging torque, torque ripple, power factor, and efficiency, show proportionate variation to the coupling level. A comparative analysis shows that MI exhibits higher average torque, lower torque ripples, and high efficiency, reaching 90% with a power factor of 0.6. As an optimal design, an MI test prototype is developed. The experimental test prototype validates the FEA results under no-load and on-load conditions. [ABSTRACT FROM AUTHOR]

Slotting effect in electric machines reduces flux per pole that effect magnetic flux density distribution in the air gap which induces harmonics in magnetic flux density causing flux pulsation, that in turn generates dominant torque pulsation in the form of cogging torque and torque ripples. To overcome the abovesaid demerits, a novel outer rotor field-excited flux-switching machine (OR-FSFSM) with a combined semi-closed and open slots stator is proposed in this study. The developed OR-FEFSM offers a high-power factor, due to the utilization of the semi-closed slot for armature coils. The open slot stator structure was chosen for the field excitation coil, which effectively suppresses leakage reluctance that causes flux pulsation. Thus, the influence of torque ripples is reduced, and the average torque is improved. In order to investigate the effectiveness of the proposed OR-FEFSM, a detailed study of stator slot and rotor pole combinations are performed. Based on simplified mathematical formulation, 12S/7P (stator slot/rotor poles), 12S/11P, 12S/13P, and 12S/17P are the most feasible combinations. Finite Element Analysis (FEA) based on comprehensive electromagnetic performance is performed on each combination, and found that 12S/13P offers the highest average torque of 4.62 Nm, whereas 3.72 Nm, 2.72Nm, and 1.68 Nm average torque is offered by 12S/17P, 12S/7P, and 12S/11P, respectively. Based on the initial analysis, 12S/13P was considered for further analysis and optimized using JMAG built-in Genetic Algorithm (GA). Moreover, thermal analysis was performed, and the proposed design was compared with the conventional design. [ABSTRACT FROM AUTHOR]

A dual mover yokeless multi-tooth (DMYMT) permanent magnet flux switching motor (PM-FSM) design is presented in this article for ropeless elevator applications. The excitation sources, including a field winding and permanent magnet, are on the short mover in the proposed design structure, whereas the stator is a simple slotted iron core, thus reducing the vertical transportation system cost. The operational principle of the proposed DMYMT in PM-FSM is introduced. The proposed dual mover yokeless multi-tooth Permanent Magnet Flux Switching Motor is analyzed and compared for various performance parameters in a Finite Element Analysis package. The proposed machine has high thrust force and cost-effectiveness compared to conventional dual permanent magnet motor. Finally, this paper also develops an analytical model for the proposed structure, validated by comparing it with Finite Element Analysis simulation results. Results show good agreement between analytical prediction and Finite Element Analysis results. [ABSTRACT FROM AUTHOR]

Double sided linear flux switching permanent magnet machines (DSLFSPMMs) exhibit high thrust force density, high efficiency, low cost and robust double salient secondary (stator) structures. The aforementioned unique features make DSLFSPMM suitable for long stroke applications. However, distorted flux linkage waveforms and high detent forces can exaggerate thrust force ripples and reduce their applicability in many areas. In order to enhance thrust force performance, reduce thrust force ripple ratio and total harmonic distortion (THD) of no-load flux linkages, two structure-based advancements are introduced in this work, i.e., asynchronous mover slot and stator tooth displacement technique (AMSSTDT) and the addition of an active permanent magnet end slot (APMES). Furthermore, single variable geometric optimization (SVGO) is carried out by the finite element method (FEM). [ABSTRACT FROM AUTHOR]