Search

Partial substitution of synthetic nitrogen fertilizer with manure (organic substitution) is highly recommended to minimize environmental risks without compromising crop productivity in intensive agricultural systems. However, our understanding of the effect of organic substitution on soil organic carbon (OC) and total nitrogen (TN) in deep soil and its impact on crop productivity remains limited. Here we investigated OC and TN changes in soil profile down to 100 cm, crop yield, and sustainable yield index under synthetic nitrogen, phosphate, and potassium fertilizers (NPK), NPK plus straw (NPKS), and organic substitution (NPKM) treatments over two decades in four upland fields across different climate zones. Compared with the initial values, two decades of NPKM treatment significantly (p < 0.05) increased OC and TN stocks in either topsoil (by 25.6–103.8 and 15.8–89.8%) or deep soil (by 2.9–71.3 and 5.7–36.9%), respectively, across all sites. The increases in OC and TN stocks in 0–100 cm soil receiving NPKM were significantly higher than those receiving NPK at all sites and NPKS at three high-evaporation sites. Compared with NPKS and NPK treatments, crop yield and N uptake were significantly increased under NPKM treatment only at the Qiyang site. Furthermore, OC sequestration in the entire soil profile down to 100 cm and TN accumulation in topsoil exhibited significant positive correlations with crop N uptake, relative crop yield, and sustainable yield index. In conclusion, long-term partial substitution of synthetic N fertilizer with manure facilitates soil OC and TN sequestration in the entire 100 cm profile and thus maintains high crop productivity in upland areas. [ABSTRACT FROM AUTHOR]

The wind tunnel balance signal detection system is widely employed in aerospace applications for the accurate and automated measurement of aerodynamic forces and moments. However, measurement errors arise under different environmental temperature. This paper addresses the issue of measurement accuracy under different temperature conditions by proposing a temperature compensation method based on an improved gray wolf optimization (IGWO) algorithm and optimized extreme learning machine (ELM). The IGWO algorithm is enhanced by improving the initial population position, convergence factor, and iteration weights of the gray wolf optimization algorithm. Subsequently, the IGWO algorithm is employed to determine the optimal network parameters for the ELM. The calibration decoupling experiment and high-low temperature experiment are designed and carried out. On this basis, ELM, GWO-ELM, PSO-ELM, GWO-RBFNN and IGWO-ELM are used for temperature compensation experiments. The experimental results show that IGWO-ELM has a good temperature compensation effect, reducing the measurement error from 20 % F S to within 0.04 % F S . Consequently, the accuracy and stability of the wind tunnel balance signal detection system under different temperature environments are enhanced. [ABSTRACT FROM AUTHOR]

This research investigates the effects of iron tailings content on the mechanical properties and durability of concrete under dry–wet cycling and negative temperature conditions (−10 °C), where iron tailings replace river sand at rates of 0%, 10%, 20%, and 30%. A variety of tests were conducted on the iron tailings concrete, including compressive strength, flexural strength, splitting tensile strength, mass loss, and relative dynamic modulus, and its pore characteristics were analyzed using low-field nuclear magnetic resonance (NMR) experiments. The results reveal that when 20% of the river sand was replaced with iron tailings, the concrete achieved optimal splitting strength, compressive strength, and flexural strength at 28 days, improving by 0.46 MPa, 3.14 MPa, and 0.41 MPa, respectively, compared to conventional concrete. Furthermore, the concrete containing this proportion of iron tailings demonstrated superior mechanical properties and durability in both negative temperature conditions and dry–wet cycling experiments. Due to the excellent physical and chemical properties of iron tailings, they enhance the performance of concrete when incorporated in appropriate quantities. The fine granularity of iron tailings helps to compensate for the granularity defects in concrete aggregates by filling internal voids, optimizing the pore structure, and improving the concrete's density and integrity. This enhances the concrete's mechanical properties and its resistance to external solutions and harmful ion penetration. Additionally, the active substances in iron tailings promote the hydration reaction of cement, leading to the formation of an increased amount of C-S-H gel and other hydration products in the cement system. [ABSTRACT FROM AUTHOR]

Due to the high incidence of PRRSV mutation and recombination, PRRSV infection is difficult to prevent and control in China and worldwide. Two species of PRRSV, Betaarterivirus suid 1 (PRRSV-1) and Betaarterivirus suid 2 (PRRSV-2), exist in China, and PRRSV-1 has always received less attention in China. However, the number of PRRSV-1 strains detected in China has increased recently. To date, PRRSV-1 has spread to more than 23 regions in China. Based on the phylogenetic analysis of ORF5 and the whole genome of PRRSV-1, Chinese PRRSV-1 can be divided into at least seven independent subgroups. Among them, BJEU06-1-like has become the mainstream subgroup in some regions of China. This subgroup of strains has a 5-aa (4 + 1) characteristic discontinuous deletion pattern at aa 357~aa 360 and aa 411 in Nsp2. Previous studies have indicated that the pathogenicity of PRRSV-1 in China is mild, but recent studies found that the pathogenicity of PRRSV-1 was enhanced in China. Therefore, the emergence of PRRSV-1 deserves attention, and the prevention and control of PRRSV-1 infection in China should be strengthened. PRRSV infection is usually prevented and controlled by a combination of virus monitoring, biosafety restrictions, herd management measures and vaccination. However, the use of PRRSV-1 vaccines is currently banned in China. Thus, we should strengthen the monitoring of PRRSV-1 and the biosafety management of pig herds in China. In this review, we summarize the prevalence of PRRSV-1 in China and clarify the genomic characteristics, pathogenicity, vaccine status, and prevention and control management system of PRRSV-1 in China. Consequently, the purpose of this review is to provide a basis for further development of prevention and control measures for PRRSV-1. [ABSTRACT FROM AUTHOR]

The storage of soil organic carbon (SOC) in cropland soils is an essential strategy that serves the dual purpose of enhancing soil fertility and mitigating climate change. However, how the stability of stored carbon is altered under long-term fertilization has not been well understood, especially in the double rice cropping system in Chinese paddy soils. In this study, we explored the SOC storage and consequent stability of SOC under long-term fertilization. The soil samples were fractionated chemically to isolate various fractions and constituent pools of SOC (i.e., very labile C/VLC, labile C/LC, less labile C/LLC, and non-labile C/NLC). The following treatments were tested: control (CK), recommended rate of inorganic fertilizer (NPK), double the amount of recommended rate of inorganic fertilizer (2NPK), and NPK combined with manure (NPKM). The results showed that, relative to the initial level, the application of NPKM significantly improved the SOC storage as compared to the control. The long-term NPKM increased the total SOC in the paddy soil and this increased SOC was mainly stored in LLC, as revealed by the highest increase (142%) over the control. Furthermore, the highest proportion of labile pool was associated with unfertilized CK, while the reverse was true for the recalcitrant pool, which was highest under NPKM. This supports the role of combining manure with NPK to improve the stability of SOC, further verified by the high recalcitrance index under NPKM (56.75% for 0–20 cm and 57.69% for 20–40 cm) as compared to the control. [ABSTRACT FROM AUTHOR]

Prostaglandin E2 (PGE2) is an important metabolite of arachidonic acid which plays a crucial role in vascular physiology and pathophysiology via its four receptors (EP1-4). However, the role of vascular smooth muscle cell (VSMC) EP4 in neointimal hyperplasia is largely unknown. Here we showed that VSMC-specific deletion of EP4 (VSMC-EP4) ameliorated, while VSMC-specific overexpression of human EP4 promoted, neointimal hyperplasia in mice subjected to femoral artery wire injury or carotid artery ligation. In vitro studies revealed that pharmacological activation of EP4 promoted, whereas inhibition of EP4 suppressed, proliferation and migration of primary-cultured VSMCs. Mechanically, EP4 significantly increased the protein expression of tenascin C (TN-C), a pro-proliferative and pro-migratory extracellular matrix protein, at the translational level. Knockdown of TN-C markedly suppressed EP4 agonist-induced VSMC proliferation and migration. Further studies uncovered that EP4 upregulated TN-C protein expression via the PKA/mTORC1/Ribosomal protein S6 (rpS6) pathway. Together, our findings demonstrate that VSMC EP4 increases TN-C protein expression to promote neointimal hyperplasia via the PKA-mTORC1-rpS6 pathway. Therefore, VSMC EP4 may represent a potential therapeutic target for vascular restenosis. [ABSTRACT FROM AUTHOR]

Polymers have an excellent effect in terms of moderating fast neutrons with rich hydrogen and carbon, which plays an indispensable role in shielding devices. As the shielding of neutrons is typically accompanied by the generation of γ-rays, shielding materials are developed from monomers to multi-component composites, multi-layer structures, and even complex structures. In this paper, based on the typical multilayer structure, the integrated design of the shield component structure and the preparation and performance evaluation of the materials is carried out based on the design sample of the heat-resistant lightweight polymer-based interlayer. Through calculation, the component structure of the polymer-based materials and the three-layer thickness of the shield are obtained. The mass fraction of boron carbide accounts for 11% of the polymer-based material. Since the polymer-based material is the weak link of heat resistance of the multilayer shield, in terms of material selection and modification, the B4C/TiO2/polyimide molded plate was prepared by the hot-pressing method, and characterization analysis was conducted for its structure and properties. The results show that the ball milling method can mix the materials well and realize the uniform dispersion of B4C and TiO2 in the polyimide matrices. Boron carbide particles are evenly distributed in the material. Except for Ti, the other elemental content of the selected areas for mapping is in good agreement with the theoretical values of the elemental content of the system. The prepared B4C/TiO2/polyimide molded plate presents excellent thermal properties, and its glass transition temperature and initial thermal decomposition temperature are as high as 363.6 °C and 572.8 °C, respectively. In addition, the molded plate has good toughness performs well in compression resistance, shock resistance, and thermal aging resistance, which allows it to be used for a long time under 300 °C. Finally, the prepared materials are tested experimentally on an americium beryllium neutron source. The experimental results match the simulation results well. [ABSTRACT FROM AUTHOR]

A series of nine enmein-type ent-kaurane diterpenoid and furoxan-based nitric oxide (NO) donor hybrids (10a-i) were designed and synthesized from commercially available oridonin (1). These hybrids were evaluated for their antiproliferative activity against Bel-7402, K562, MGC-803, and CaEs-17 human cancer cell lines and L-02 normal liver cells. The antiproliferative activity against tumor cells was stronger than the lead compound 1 and parent molecule 9 in most cases. Especially, compound 10f showed the strongest activity against human hepatocarcinoma Bel-7402 cell line with an IC50 of 0.81 μM and could also release 33.7 μmol/L NO at the time point of 60 min. Compounds 10a-i also showed cytotoxic selectivity between tumor and normal liver cells with IC50 ranging from 22.1 to 33.9 μM. Furthermore, the apoptotic properties on Bel-7402 cells revealed that 10f could induce S phase cell cycle arrest and apoptosis at low micromolar concentrations. The effects of 10f on apoptosis-related proteins were also investigated. The potent antiproliferative activities and mechanistic studies warrant further preclinical investigations. [ABSTRACT FROM AUTHOR]

Target detection in side-scan sonar images plays a significant role in ocean engineering. However, the target images are usually severely interfered by the complex background and strong environmental noise, which makes it difficult to extract robust features from small targets and makes the target detection task quite challenging. In this paper, a novel small target detection method in sonar images is proposed based on the low-rank sparse matrix factorization. Initially, the side-scan sonar images are preprocessed so as to highlight the individual differences of the target. Then, the problems of target feature extraction and noise removal are characterized as the problem of matrix decomposition. An improved Robust Principal Component Analysis algorithm is used to extract target information, and the fast proximal gradient method is used to optimize the solution. The original sonar image is reconstructed into the low-rank background matrix, the sparse target matrix, and the noise matrix. Eventually, a morphological operation is used to filter out the noise and refine the target edges in the target matrix for improving the accuracy of target detection. Experimental results show that the proposed method not only achieves better detection performance in comparison to the conventional baseline algorithms but also performs robustly in various signal-to-clutter ratio conditions. [ABSTRACT FROM AUTHOR]

Herein, we reported on a series of synthetic nitric oxide-releasing enmein-type diterpenoid hybrids (9a-i). All the target compounds showed potent antibacterial activity against selected Gram-positive bacteria S. aureus and B. subtilis. The antiproliferative activity against human tumor K562, MGC-803, CaEs-17 and Bel-7402 cells, and human normal liver cells L-02 was tested and the structure activity relationships (SARs) were also concluded. Compounds 9b and 9d showed the best activity against S. aureus and B. subtilis with the same minimal inhibitory concentrations (MICs) of 4 and 2 μg/mL, respectively. The derivative 9f displayed IC50 values of 1.68, 1.11, 3.60 and 0.72 μM against the four cancer cell lines above and 18.80 μM against normal liver cells L-02; meanwhile, 9f also released a high level of NO at the time point of 60 min of 22.24 μmol/L. Furthermore, it was also found that 9f induced apoptosis via the mitochondria-related pathway and arrested cell cycle of Bel-7402 cells at S phase. These findings might be important to explore new chemical entities for the main causes of in-hospital mortality of S. aureus infection, combined with a solid tumor. [ABSTRACT FROM AUTHOR]

To study the chemical constituents of the fruits of noni (Morinda citrifolia L.), and find novel compounds, an n-butanol extract of the ethanol soluble fraction was subjected to repeated silica gel and ODS column chromatography and HPLC. Two new glycosides were isolated and their structures elucidated by NMR and HRFAB-MS spectrometry as (2E,4E,7Z)-deca-2,4,7-trienoate-2-O-β-D-glucopyranosyl-β-D-glucopyranoside (1) and amyl-1-O-β-D-apio-furanosyl-1,6-O-β-D-glucopyranoside (2), respectively. [ABSTRACT FROM AUTHOR]

Particle-reinforced composites are widely applied as nuclear radiation shielding materials for their excellent comprehensive properties. The work aimed to calculate the influence of the functional reinforced particles spatial arrangement on the neutron shielding performance of composites and attempted to explain the influence mechanism by investigating the neutron flux distribution in the materials. Firstly, four suitable physical models were established based on the Monte Carlo Particle Transport Program (MCNP) and mathematical software MATLAB, namely the RSA (Random Sequential Adsorption) Model with particles random arrangement and FCC Model, BCC Model and Staggered Arrangement Model (SA Model) with particle periodic arrangements. Later, based on these four physical models, the neutron transmittance of two kinds of typical B4C reinforced composites, 316 stainless steel matrix composite and polyethylene matrix composite, were calculated under different energy neutrons sources (0.0253 eV, 50 eV, 50 keV, fission spectrum, 241Am-Be spectrum and 14.1 MeV) and the neutron flux distribution in the 316 stainless steel composite was also analyzed under 0.0253 eV neutron and fission neutron sources. The results indicated that the spatial arrangement of B4C has an impact on the neutrons shielding performance of the composite and the influence changes with neutron energy and B4C content. It can be concluded that the RSA model and the periodic arrangement models can be used in different calculation cases in the future. [ABSTRACT FROM AUTHOR]

The porous-medium approximation (PM) approach is extensively employed in large-quantity grid simulations of heat exchangers, providing a time-saving approach in engineering applications. To further investigate the influence of different geometries on the implementation of the PM approach, we reviewed existing experimental conditions and performed numerical simulations on both straight fins and serrated fins. Equivalent flow and heat-transfer factors were obtained from the actual model, and computational errors in flow and heat transfer were compared between the actual model and its PM model counterpart. This exploration involved parameters such as aspect ratio (a*), specific surface area (Asf), and porosity (γ) to evaluate the influence of various geometric structures on the PM approach. Whether in laminar or turbulent-flow regimes, when the aspect ratio a* of straight fins is 0.98, the flow error ( δ f ) utilizing the PM approach exceeds 45%, while the error remains within 5% when a* is 0.05. Similarly, for serrated fins, the flow error peaks ( δ f   > 25%) at higher aspect ratios (a* = 0.61) with the PM method and reaches a minimum ( δ f   < 5%) at lower aspect ratios (a* = 0.19). Under the same Reynolds numbers (Re), employing the PM approach results in an increased heat-transfer error ( δ h )with rising porosity (γ) and decreasing specific surface area (Asf), both of which remained under 10% within the range of this study. At lower aspect ratios (a*), the fin structure becomes more compact, resulting in a larger specific surface area (Asf) and smaller porosity (γ). This promotes more uniform flow and heat transfer within the model, which is closer to the characteristics of PM. In summary, for straight fins at 0 < a* < 0.17 in the laminar regime (200 < Re < 1000) and in the turbulent regime (1200 < Re < 5000) and for serrated fins at 0 < a* < 0.28 in the laminar regime (400 < Re < 1000) or 0 < a* < 0.32, in the turbulent regime (2000 < Re < 5000), the flow and heat-transfer errors are less than 15%. [ABSTRACT FROM AUTHOR]

At present, most Mo2FeB2-based cermets are prepared by vacuum sintering. However, vacuum sintering is only suitable for ordinary cylinder and cuboid workpieces, and it is difficult to apply to large curved surface and large size workpieces. Therefore, in order to improve the flexibility of preparing Mo2FeB2 cermet, a flux cored wire with 70% filling rate, 304 stainless steel, 60 wt% Mo powder and 40 wt% FeB powder was prepared. Mo2FeB2 cermet was prepared by an arc cladding welding metallurgy method with flux cored wire. In this paper, the microstructure, phase evolution, hardness, wear resistance and corrosion resistance of Mo2FeB2 cermets prepared by the vacuum sintering (VM-Mo2FeB2) and arc cladding welding metallurgy method (WM-Mo2FeB2) were systematically studied. The results show that VM-Mo2FeB2 is composed of Mo2FeB2 and γ-CrFeNi.WM-Mo2FeB2 is composed of Mo2FeB2, NiCrFe, MoCrFe and Cr2B3. The volume fraction of hard phase in WM-Mo2FeB2 is lower than that of VM-Mo2FeB2, and its hardness and corrosion resistance are also slightly lower than that of VM-Mo2FeB2, but there are obvious pores in the microstructure of VM-Mo2FeB2, which affects its properties. The results show that WM-Mo2FeB2 has good diffusion and metallurgical bonding with the matrix and has no obvious pores. The microstructure is compact and the wear resistance is better than that of VM-Mo2FeB2. [ABSTRACT FROM AUTHOR]

Simple Summary: In this study, we investigated the effects of palmitic acid (PA) on multiple human gastric cancer cell lines and combined them with the results from clinical gastric cancer and paracancerous tissue samples. Our findings demonstrated that PA exerted anti-gastric cancer effects by regulating key molecules in the signal transduction and activation of a transcription 3 (STAT3) protein inhibitor of the activated STAT 3 (PIAS3) signaling pathway. Our results serve as a foundation for further research on the correlation between the anti-gastric cancer activity of PA and the STAT3-PIAS3 signaling pathway. Our results also represent a critical step toward understanding gastric cancer prevention and prognosis and promoting PA supplementation as a gastric cancer treatment. Lipidomic analyses have suggested that palmitic acid (PA) is linked to gastric cancer. However, its effects and action mechanisms remain unclear. Therefore, we evaluated the effects of PA on cell proliferation, invasion, and apoptosis in human gastric cancer, as well as the role of p-STAT3 in mediating its effects. The results of the MTT and colony formation assays revealed that PA blocked gastric cancer cell proliferation in a concentration-dependent manner. The EdU-DNA assay indicated that 50 μM of PA could block gastric cell proliferation by 30.6–80.0%. The Transwell assay also confirmed the concentration dependence of PA-induced inhibitory effect on cell invasion. The flow cytometry analysis indicated that PA treatment for 18 h could induce gastric cancer cell apoptosis. The immunohistochemical staining revealed that p-STAT3 levels were higher in the gastric cancer tissues than in the control tissues. We demonstrated that PA treatment for 12 h decreased the expressions of p-STAT3, p-JAK2, N-cadherin, and vimentin, and inhibited the nuclear expression of p-STAT3 in gastric cancer cells. Finally, PA treatment (50 mg/kg) decreased gastric cancer growth (54.3%) in the xenograft models. Collectively, these findings demonstrate that PA inhibits cell proliferation and invasion and induces human gastric cancer cell apoptosis. [ABSTRACT FROM AUTHOR]

Numerical simulations were carried out for moist, porous media, intermittent microwave convective drying (IMCD) using a multiphase flow model in porous media subdomains coupled with a forced-convection heat-transfer model in an external hot air subdomain. The models were solved by using COMSOL Multiphysics was applied at the pulse ratio (PR) of 3. Based on drying characteristics of porous media and the distribution of the evaporation interface, IMCD was compared with convection drying (CD). Drying uniformity K, velocity difference, temperature difference, and humidity difference were introduced to evaluate the performance of three models with different inlets and outlet wall curvature. The numerical results show that as the moisture content of slices was reduced to 3 kg/kg, the drying rate in IMCD was 0.0166–0.02 m/s higher than that in CD, and the total drying time of the former was 81.35% shorter than that of the latter. In the late drying stage of IMCD, the core of the sample still had a high vapor concentration and temperature, which led to the evaporation interface remaining on the surface. The vapor evaporated from the slices can diffuse rapidly to the outside, which is why IMCD is superior to traditional convection drying. Through the comprehensive analysis of the models with different inlet and outlet wall curvatures, the drying uniformity K of the type III was the highest, reaching 89.28%. Optimizing flow-field distribution can improve uniform of airflow distribution. [ABSTRACT FROM AUTHOR]

Alloy blocks with different TiC content were designed, and Mo2FeB2 cermets were prepared by carbon arc surfacing process. The interaction law of TiC content and the microstructure, phase, composition, hardness and wear resistance of the cladding were studied in detail by the combination of experiment and theoretical analysis. On the other hand, the phase transition process of the weldpool is theoretically analyzed by thermodynamic calculation method. XRD test results show that in addition to Mo2FeB2 synthesized in situ, the cladding also forms phases such as TiC, CrB, MoB and Fe-Cr. The number of Mo2FeB2 hard phases gradually increases when TiC content varies from 0% to 15%. The average microhardness of the cladding with 0%, 5%, 10%, and 15% TiC was 992 HV0.5, 1035 HV0.5, 1018 HV0.5 and 689 HV0.5, respectively, with 5% TiC being the largest. Moreover, the cladding with 5% TiC content has excellent wear resistance, which is 14.6 times that of the substrate. [ABSTRACT FROM AUTHOR]

As toxic gaseous pollution, carbon monoxide (CO) plays an essential role in many pathological and physiological processes, well-known as the third gasotransmitter. Owning to the reducibility of CO, the Pd0-mediated Tsuji-Trost reaction has drawn much attention in CO detection in vitro and in vivo, using allyl ester and allyl ether caged fluorophores as probes and PdCl2 as co-probes. Because of its higher decaging reactivity than allyl ether in the Pd0-mediated Tsuji-Trost reaction, the allyl ester group is more popular in CO probe design. However, during the application of allyl ester caged probes, it was found that bovine serum albumin (BSA) in the fetal bovine serum (FBS), an irreplaceable nutrient in cell culture media, could hydrolyze the allyl ester bond, and thus give erroneous imaging results. In this work, dicyanomethylenedihydrofuran (TCF) and dicyanoisophorone (DCI) were selected as electron acceptors for constructing near-infrared-emission fluorophores with electron donor phenolic OH. An allyl ester and allyl ether group were installed onto TCF-OH and DCI-OH, constructing four potential CO fluorescent probes, TCF-ester, TCF-ether, DCI-ester, and DCI-ether. Our data revealed that ester bonds of TCF-ester and DCI-ester could completely hydrolyze in 20 min, but ether bonds in TCF-ether and DCI-ether tolerate the hydrolysis of BSA and no released fluorescence was observed even up to 2 h. Moreover, passing through the screen, it was concluded that TCF-ether is superior to DCI-ether due to its higher reactivity in a Pd0-mediated Tsuji-Trost reaction. Also, the large stokes shift of TCF-OH, absorption and emission at 408 nm and 618 nm respectively, make TCF-ether desirable for fluorescent imaging because of differentiating signals from the excitation light source. Lastly, TCF-ether has been successfully applied to the detection of CO in H9C2 cells. [ABSTRACT FROM AUTHOR]

Oridonin belongs to ent-kaurane tetracyclic diterpenoid and was first isolated from Isodon species. It exhibits inhibitory activities against a variety of tumor cells, and pharmacological study shows that oridonin could inhibit cell proliferation, DNA, RNA and protein synthesis of cancer cells, induce apoptosis and exhibit an antimutagenic effect. In addition, the large amount of the commercially-available supply is also very important for the natural lead oridonin. Moreover, the good stability, suitable molecular weight and drug-like property guarantee its further generation of a natural-like compound library. Oridonin has become the hot molecule in recent years, and from the year 2010, more than 200 publications can be found. In this review, we summarize the synthetic medicinal chemistry work of oridonin from the first publication 40 years ago and share our research experience of oridonin for about 10 years, which may provide useful information to those who are interested in this research field. [ABSTRACT FROM AUTHOR]

Isodon rubescens has been used as a traditional green tea for more than 1000 years and many medicinal functions of I. rubescens are also very useful, such as its well-known antitumor and antibacterial activities. Oridonin, a bioactive ent-kaurane diterpenoid, is the major ingredient of this medicinal tea. Herein, 22 novel oridonin derivatives were designed and synthesized. The antibacterial activity was evaluated for the first time. Compound 12 was the most promising one with MIC of 2.0 µg/mL against B. subtilis, which was nearly 3-fold stronger than positive control chloromycetin. The antiproliferative property was also assayed and compound 19 showed stronger activity than taxol. The apoptosis-inducing ability, cell cycle arrest effect at S phase and influence of mitochondrial membrane potential by 19 in CaEs-17 cancer cells were first disclosed. Based on the above results, the cell apoptosis induced by compound 19 in CaEs-17 cells was most probably involved in the intrinsic apoptotic pathway. [ABSTRACT FROM AUTHOR]

Mo2FeB2 ceramics-reinforced Fe-based cladding with various rare earth (RE) concentrations were prepared by the carbon arc surfacing process. The effects of RE content on the microstructure, phase composition, hardness and wear resistance of the cladding were systematically discussed. Meanwhile, the area fraction and grain size of Mo2FeB2 phase were exactly measured. Moreover, the refining mechanism of rare earth Y was analyzed. Results revealed that the claddings consisted of Mo2FeB2, FeCr, MoB and CrB. Adding the rare-earth Y decreased the grain sizes of Mo2FeB2 phase. Furthermore, grain-refining effects of Mo2FeB2 phase were significant when the RE content was 2% and hard phases evenly distributed in the cladding. In addition, the maximum microhardness value of claddings was about 1078 HV. The claddings with 2% RE contents had better wear resistance, which was equivalent to a sintered sample. [ABSTRACT FROM AUTHOR]

The highly expressed circHIPK3 is a circular RNA that has been previously reported to regulate the growth of human cells. In this study, we found an increased expression of circHIPK3 in bovine mammary epithelial cells treated with prolactin (PRL) in high-throughput sequencing data. Thus, we further investigated the effect of circHIPK3 on the proliferation and differentiation of mammary epithelial cells. We used qRT-PCR/Cell Counting Kit-8 (CCK-8) and a Western blotting analysis to evaluate the effects on cell proliferation. We found that circHIPK3 promotes the proliferation of mammary epithelial cells. The STAT5 signaling pathway was previously associated with the prolactin response and when the STAT5 was suppressed, the expression of circHIPK3 decreased. The results suggest that the response to prolactin and the associated STAT5 signaling pathway affect the expression of circHIPK3, which subsequently affects the proliferation of mammary epithelial cells in dairy cows. [ABSTRACT FROM AUTHOR]