Search

This paper aims to discuss the internal flow and cavitation characteristics of petal bionic nozzle holes under different injection pressures to improve the atomization effect of methanol. The FLUENT (v2022 R1) software is used for simulation. The Schnerr-Sauer cavitation model in the Mixture multiphase flow model is adopted, considering the evaporation and condensation processes of methanol fuel to accurately simulate cavitation and internal flow performance. The new nozzle hole is compared with the ordinary circular nozzle hole for analysis to ensure research reliability. The results show that the cavitation of the petal bionic nozzle hole mainly occurs at the outlet, which can enhance the atomization effect. In terms of turbulent kinetic energy, the internal turbulent kinetic energy of the petal bionic nozzle hole is greater under the same pressure. At 1 MPa, its outlet turbulent kinetic energy is 38.37 m2/s2, which is about 2.3 times that of the ordinary circular nozzle hole. When the injection pressure is from 0.2 MPa to 1 MPa, the maximum temperature of the ordinary circular nozzle hole increases by about 33.4%, while that of the petal bionic nozzle hole only increases by 12.3%. The intensity of internal convection and vortex is significantly reduced. The outlet velocity and turbulent kinetic energy distribution of the petal bionic nozzle hole are more uniform. In general, the internal flow performance of the petal bionic nozzle hole is more stable, which is beneficial to the collision and fragmentation of droplets and has better uniformity of droplet distribution. It has a positive effect on improving the atomization effect of methanol injection in the intake port of methanol-diesel dual-fuel engines. [ABSTRACT FROM AUTHOR]

Polyethylene terephthalate (PET) is widely used in bottle production by stretch blow molding processes (SBM processes) due to its cost-effectiveness and low environmental impact. The presented literature review focuses on microcavitation and solid-state post-condensation effects that occur during the deformation of PET in the SBM process. The literature review describes cavitation and microcavitation effects in PET material and solid-state post-condensation of PET on the basis of a three-phase model of the PET microstructure. A three-phase model of PET microstructure (representing the amorphous phase in two ways, depending on the ratio of the trans-to-gauche conformation of the PET macromolecule and the amount of free volume) with a nucleation process, a crystallization process, and the use of positron annihilation lifetime spectroscopy (PALS) to analyze PET microstructure are discussed in detail. The conceptual model developed based on the literature combines solid-state post-condensation with microcavitation via the diffusion of the post-condensation product. This review identifies the shortcomings of the developed conceptual model and presents them with five hypotheses, which will be the basis for further research. [ABSTRACT FROM AUTHOR]

Among the many methods of joining different materials, gluing is characterized by its most specific nature. In comparison with, for example, welded, screwed, or overlapped connections, a glued connection depends on the largest number of factors. Many of them are related to the phenomenon of adhesion, which is complicated by definition. It has many shapes and forms, and its existence determines not only the durability of such a joint but also the possibility of its execution. Epoxy polymers are among the most commonly used adhesives. Their extremely good parameters can be easily modified by additives in the form of fillers. Compatibility between the filler and the adhesive allows for further improving the adhesive parameters in the glued joint. However, in order to effectively combine the adhesive and the filler, different, often specific mixing methods must be used. The following study presents the results obtained in an experimental research program, the aim of which was to increase the adhesion of epoxy resin to a properly prepared concrete substrate. As a method to increase the final adhesion, the addition of microsilica and carbon nanotubes in an experimentally determined amount was selected. The use of sonication as a mixing method together with cavitation allowed for improving the parameters which determine the final adhesion of the adhesive to concrete. The parameters which were selected to describe the course of changes in the adhesion of the adhesive to the concrete substrate were the viscosity, free surface energy, surface parameters, adhesion, and SEM images of the tested resin in various modification configurations. The obtained results make it possible to form stronger and more durable adhesive joints during the reinforcement of concrete structural elements using fiber-reinforced polymer (FRP) composites. [ABSTRACT FROM AUTHOR]

Propeller cavitation performance can be predicted based on model tests or simulations. However, the cavitation performance of an ice-blocked propeller near the free surface differs from that of a propeller in the cavitation tunnel. Therefore, research on the cavitation performance simulation of propellers near the free surface holds crucial scientific significance. In this study, a coupled model was established using Computational Fluid Dynamics (CFD) and the Volume of Fluid (VOF) coupling method. The CFD-VOF model weighted the overlapping grids and simulated the cavitation performance of an ice-blocked propeller using various immersion depths, cavitation numbers, and advance coefficients. The propeller inflow ahead of the propeller and the wake field behind it were controlled to accurately obtain the propeller cavitation performance. Moreover, a comparison was conducted between the cavitation tunnel test results and the numerical simulation results at various immersion depths. When the immersion depth was at a distance of 1D, the effect of the free surface on the propeller cavitation performance became significant. When the immersion depth was at a distance of 9D, the average errors between the numerical simulation and the model test data were within 10%. This study analyzed the cavitation performance of ice-blocked propellers near the free surface and provided valuable insights for the design of ice-class propellers. [ABSTRACT FROM AUTHOR]

Mixed-flow pumps, optimized for marine engineering, provide a balance of high efficiency and adaptability, accommodating varied flow and head demands across challenging oceanic settings and are essential for reliable operations in tidal energy and subsea applications. The primary purpose of this paper is to perform a numerical analysis of the cavitation flow characteristics of the mixed-flow pump under differing operational circumstances. The cavitation simulation was implemented to explore the cavitation bubbles evolution and the pressure pulsation characteristics in the impeller region under diverse flow rates, utilizing the Shear Stress Transport (SST) turbulence model and the Zwart-Gerber-Belamri cavitation model as a foundation. The findings indicate that cavitation bubbles initially distribute at the leading edge of blade suction surfaces at the cavitation growth stage. The bubbles spread gradually with the decline of the available net positive suction head (NPSHa). At the same time, many bubbles appear in the area below the blade and extend to the rim of the suction side of blades. As the flow rate decreases, the critical net positive suction head (NPSHc) gradually declines. The dominant pressure pulsation frequency at the impeller inlet is the blade passing frequency, and the vibration at the impeller shroud inlet is more intense than that at the hub. The dominant frequency at the impeller outlet is mainly the blade passing frequency. With the development of cavitation, it changes to impeller rotation frequency at low flow rates, while the dominant frequency remains unchanged at high flow rates. [ABSTRACT FROM AUTHOR]

The pressing issue of global warming, coupled with the increasing depletion of fossil fuels, highlights the necessity for sustainable energy solutions. In this context, hydrogen stands out as a viable option, possessing the capacity to revolutionize critical industries, including fuel cells, internal combustion engines, and gas turbines. An effective approach to enhancing numerous chemical and technological processes in liquid and steam–gas mixtures is the establishment of cavitation mixing zones for the reacting components. These zones are produced in specialized reactors that operate on the principles of hydrodynamic effects applied to the reaction medium. The study focused on the design of the cavitation-jet chamber utilizing the k– ω Turbulence Model and Particle Tracing Model. As a result, the influence of the inlet velocity on cavitation formation and the uniformity of mixing was investigated. Ripley's K-function was used to analyze the results of particle distribution. The influence of the screw on flow turbulence and the uniformity of particles was evaluated. Analysis through the K-function indicated a decrease in uniformity at lower velocities, with noticeable turbulization of the flow occurring at high velocities, which facilitated better mixing. In contrast, without the screw, the flow exhibited a high longitudinal velocity and minimal transverse velocity, limiting particle dispersion to the radius of the nozzle and resulting in inefficient mixing. It was found that the inclusion of the screw not only enhanced particle distribution but also maintained the size of the cavitation zones, thereby improving the overall efficiency of the design. [ABSTRACT FROM AUTHOR]

Cavitation is a common phenomenon in naval and ocean engineering, typically occurring in the wakes of high-speed rotating propellers and on the surfaces of fast-moving underwater vehicles. To investigate cavitation phenomena, computational fluid dynamics (CFD) simulations are indispensable. Nevertheless, the inherently complex nature of cavitation, which involves phase transitions, heat transfer, and significant pressure fluctuations, often results in high computational costs for these simulations. To address the computational challenges associated with cavitation simulations, a DeepCFD model, which leverages convolutional neural networks (CNNs), was employed to accurately predict cavitation around hydrofoils. Through specific modifications, the DeepCFD model was trained on 400 hydrofoil configurations, learned from CFD simulations. The numerical methods were validated against a modified NACA66 hydrofoil. It was found that the model could accurately predict cavitation shapes under various flow conditions, although it showed some discrepancies in velocity predictions, especially for detached cavitating flows. The significance of this study lies in its potential to simply predict cavitating flows and expedite marine vehicle design through the application of CNNs in cavitation prediction, offering a novel and impactful approach to computational fluid dynamics in the field. [ABSTRACT FROM AUTHOR]

In conventional double-hulled submarines, the connecting structures that facilitate the linkage between the two hulls are crucial for load transmission. This paper aims to elucidate the effect of these connecting structures on resistance to shock waves generated by underwater explosions. Firstly, a self-developed numerical solver is built for the one-dimensional water-filled elastically connected double-layer plate model. The shock wave propagation characteristics, shock response of structure, water cavitation, and impact loads transmitted through the gap water and the connecting structures are analyzed quantitatively. The results reveal that the majority of the shock impulse is transmitted by the gap water if the equivalent stiffness of the connecting structures is much less than that of the gap water. Then, a three-dimensional model of the double-hulled, water-filled cylindrical shell is constructed in Abaqus/Explicit, utilizing the acoustic-structural coupling methodology. The analysis focuses on the influence of the thickness and density distribution of the connecting structures on the system's shock response. The results indicate that a densely arranged connecting structure results in a wavy deformation of the outer hull and a notable reduction in both the impact response and strain energy of the inner hull. When the stiffness of the densely arranged connecting structure is comparatively low, the internal energy and plastic energy of the inner hull are decreased by 16.5% and 24.1%, respectively. The findings of this research are useful for assessing shock resistance and for the design of connecting structures within conventional double-hulled submarines. [ABSTRACT FROM AUTHOR]

Cavitation is a phase-change phenomenon from the liquid to the gas phase due to an increased flow velocity. As it causes severe erosion and noise, it is harmful to hydraulic machinery such as pumps, valves, and screw propellers. However, it can be utilized for water treatment, in chemical reactors, and as a mechanical surface treatment, as radicals and impacts at the point of cavitation bubble collapse can be utilized. Mechanical surface treatment using cavitation impacts is called "cavitation peening". Cavitation peening causes less pollution because it uses water to treat the mechanical surface. In addition, cavitation peening improves on traditional methods in terms of fatigue strength and the working life of parts in the automobile, aerospace, and medical fields. As cavitation bubbles are utilized in cavitation peening, the study of cavitation bubbles has significant value in improving this new technique. To achieve this, many numerical analyses combined with field experiments have been carried out to measure the stress caused by bubble collapse and rebound, especially when collapse occurs near a solid boundary. Understanding the mechanics of bubble collapse can help to avoid unnecessary surface damage, enabling more accurate surface preparation, and improving the stability of cavitation peening. The present study introduces three cavitation bubble types: single, cloud, and vortex cavitation bubbles. In addition, the critical parameters, governing equations, and high-speed camera images of these three cavitation bubble types are introduced to support a broader understanding of the collapse mechanism and characteristics of cavitation bubbles. Then, the results of the numerical and experimental analyses of non-spherical cavitation bubbles are summarized. [ABSTRACT FROM AUTHOR]

The article investigates the potential for producing hydrogen by combining the methods of water splitting under cavitation and the chemical activation of aluminum in a high-speed cavitation–jet flow generated by a specialized hydrodynamic reactor. The process of cavitation and water spraying causes the liquid heating itself until it reaches saturated vapor pressure, resulting in the creation of vapor–gaseous products from the splitting of water molecules. The producing of vapor–gaseous products can be explained through the theory of non-equilibrium low-temperature plasma formation within a high-speed cavitation–jet flow of fluid. Special focus is also given to the interactions occurring at the interface boundary phase of aluminum and liquid under cavitation condition. The primary solid products formed on aluminum surfaces are bayerite, copper oxides (I and II), iron carbide, and a compound of magnesium oxides and aluminum hydroxide. A high hydrogen yield of 60% was achieved when using a 0.1% sodium hydroxide solution as a working liquid compared to demineralized water. Moreover, hydrogen methane was also detected in the volume of the vapor–gas mixture, which could be utilized to address the challenges of decarbonization and the recycling of aluminum-containing solid industrial and domestic waste. This work provides a contribution to the study of the mechanism of hydrogen generation by cavitation–jet processing of water and aqueous alkali solutions, in which conditions are created for double cavitation in the cavitation–jet chamber of the hydrodynamic reactor. [ABSTRACT FROM AUTHOR]

Cavitation is a disadvantageous phenomenon that occurs when fluid pressure drops below its vapor pressure. Under these conditions, bubbles form in the fluid. When these bubbles flow into a high-pressure area or tube, they erupt, causing harm to mechanical parts such as centrifugal pumps. The difference in pressure in a fluid is the result of varying temperatures. One way to eliminate cavitation is to reduce the radius of the bubbles to zero before they reach high-pressure areas, using a robust approach. In this paper, sliding mode control is used for this purpose due to its invariance property. To force the radius of the bubbles toward zero and prevent chattering, a new dynamic sliding mode control approach is used. In dynamic sliding mode control, chattering is removed by passing the input control through a low-pass filter, such as an integrator. A general model of the spherical bubble is used, transferred to the state space, and then a state proportional-integral feedback is applied to obtain a linear system with a new input control signal. A comparison is also made with traditional sliding mode control using state feedback, providing a trusted comparison. [ABSTRACT FROM AUTHOR]

Cavitation erosion, as a mechanical effect of destruction, constitutes a complex and critical problem that affects the safety and efficiency of the functioning of engineering components specific to many fields of work, the most well-known being propellers of ships and maritime and river vessels, seawater desalination systems, offshore oil and gas drilling platforms (including drilling and processing equipment), and the rotors and blades of hydraulic machines. The main objective of the research conducted in this paper is to experimentally investigate the phenomenology of this surface degradation process of maritime ships and offshore installations operating in marine and river waters. To reduce cavitation erosion of maritime structures made from Duplex stainless steels, the study used the deposition by welding of layers of metallic alloys with a high capacity for work hardening. The cavitation tests were conducted in accordance with the American Society for Testing and Materials standards. The response of the deposited metal under each coating condition, compared to the base metal, was investigated by calculating the erosion penetration rate (MDER) through mass loss measurements over the cavitation duration and studying the degraded zones using scanning electron microscopy (SEM), the energy-dispersive X-ray analysis, and hardness measurements. It was revealed that welding hardfacing with austenitic manganese alloy contributes to an approximately 8.5–10.5-fold increase in cavitation erosion resistance. The explanation is given by the increase in surface hardness of the coated area, with 2–3 layers of deposited alloy reaching values of 465–490 HV5, significantly exceeding those specific to the base metal, which range from 260–280 HV5. The obtained results highlighted the feasibility of forming hard coatings on Duplex stainless-steel substrates. [ABSTRACT FROM AUTHOR]

Ultrasonic pretreatment is a crucial step in the bioconversion of lignocellulosic biomass, such as peapods, into valuable products. Ultrasonic pretreatment is a highly effective physical method that utilizes ultrasonic waves to enhance various processes. Biomass pretreatment is achieved through physical effects such as acoustic cavitation, which disrupts the biomass structure, and chemical effects like radical formation, which breaks down complex molecules. This article focuses on the characteristics, types, and applications of ultrasonic pretreatment in peapods, with a particular emphasis on its role in lignin removal and ultrasound design. An innovative mechanical design in a CAD application of a continuous ultrasound treatment with a capacity of 5 L and an FEA analysis of the equipment are presented as results, providing insights for the design and optimization of ultrasonic pretreatment processes. [ABSTRACT FROM AUTHOR]

The wastewater problem is becoming an increasingly significant environmental issue affecting various aspects of human activities. The generation of reactive oxygen species (ROS) in water through certain physicochemical processes, which can oxidise or degrade various organic and chemical compounds, offers an effective purification method. The main advantage of these methods is the elimination of chemical reagents. The aim of this work is to investigate the possibility of regulating the ROS content in water by altering the characteristics of the plasma discharge that occurs under hydrodynamic cavitation in the water flow. The ROS concentration was determined using the permanganate oxidation titration technique. It was found that the content of various reactive oxygen species in water after treatment can be controlled by varying the power of the electrical pulses applied. Additionally, this study obtained the dependence of the ROS concentration in treated water samples on storage time, with results indicating that sonoplasma treatment has a prolonged effect on the antibacterial properties of water. The analysis of water samples using a biological test culture of Salmonella typhimurium revealed the bacteriostatic properties of the water for at least 48 h after sonoplasma discharge treatment. [ABSTRACT FROM AUTHOR]

A Rotary-Pulsation Apparatus (RPA), also known in the literature as a Rotational Hydrodynamic Cavitation Reactor (RHCR), is a device which typically consists of a rotating mechanism that generates pulsations or vibrations within a fluid. This can be achieved through various means such as mechanical agitation, pneumatic pulses, or hydraulic forces. It is widely used in food, chemical, pharmaceutical, and microbiological industries to improve the mixing of different fluids, dispersion, pasteurization, and sterilization. In the present paper, a CFD study was conducted to develop and optimize the geometry of the RPA's rotor and stator to induce cavitation in the fluid flow. The effect of cavitation has the potential to improve dispersion and emulsion properties and to significantly reduce operation pressure, in comparison to conventional mixing systems. [ABSTRACT FROM AUTHOR]

This paper describes the unique full-scale bollard pull and self-propulsion tests of a large amphibious tracked military vehicle with two waterjet propulsors. To provide a reference for the self-propulsion and cavitation performance, a series of sea trials and bollard pull tests were performed in a military sea bay and in a large test basin, respectively. Good overall agreement between the sea trial and the computation was observed in the speed–power relationship. The cavitation-induced breakdown phenomenon was further explored via numerical simulations. The results indicated that the uncertainties in the numerical results were dominated by the scales of vapor bubbles. The analysis showed that the selection of the vapor bubble scale factors of 1.0 for growth and 0.05 for collapse were in good agreement with the experimental results. Rapid performance breakdown occurred when sufficient suction side-attached cavities were extended into the blade mid-chord and tip-board regions. [ABSTRACT FROM AUTHOR]

The water exit problem, which is ubiquitous in ocean engineering, is a significant research topics in the interaction between navigators and water. The study of the water exit problem can help to improve the structural design of marine ships and underwater weapons, allowing for better strength and movement status. However, the water exit problem involves complex processes such as three-phase gas–liquid–solid coupling, cavitation, water separation, liquid surface deformation, and fragmentation, making it challenging to study. Following work carried out by many researchers on this issue, we summarize recent developments from three aspects: theoretical research, numerical simulation, and experimental results. In theoretical research, the improved von Karman model and linearized water exit model are introduced. Several classical experimental devices, data acquisition means, and cavitation approaches are introduced in the context of experimental development. Three numerical simulation methods, namely, the BEM (Boundary Element Method), VOF (Volume of Fluid), and FVM (Finite Volume Method) with LES (Large Eddy Simulation) are presented, and the respective limitations and shortcomings of these three aspects are analyzed. Finally, an outlook on future research improvements and developments of the water exit problem is provided. [ABSTRACT FROM AUTHOR]

In this paper, the flow characteristics of a continuous-type liquid–liquid pintle injector are described, focusing on the differential impact of a non-uniform center-flow distribution on single- and bi-injection methodologies as well as the cavitation effect on the spray angle. Using cold-flow experiments, jet-type flows of the center propellant caused by a non-uniform flow distribution were observed during a single injection. This resulted in an augmented pressure drop, as opposed to the flow characteristics of uniform single-film injection. By contrast, bi-injection modalities exhibited a substantial reduction in the pressure drop of the center propellant, underscoring a more equitable flow distribution. Moreover, the occurrence of cavitation in the center propellant was found to markedly affect the spray angle. By considering the injection exit area reduction caused by cavitation, the spray-angle prediction accuracy increased. The findings of this study are expected to reveal the interplay between flow distribution and pressure drop as well as that between cavitation and the spray angle in pintle injectors. Through this understanding, this study provides crucial considerations for the development of more efficient propulsion systems. [ABSTRACT FROM AUTHOR]

The scientific goal of this study was to investigate the effects of various parameters on cavitation-induced erosion, with the aim to enhance the understanding and assessment of cavitation resistance in hydraulic systems. Cavitation erosion poses significant challenges to the durability and efficiency of hydraulic components, such as those found in hydropower plants and pumping stations. Prompted by the need to improve the reliability of cavitation testing and material assessment, this research conducted a comprehensive sensitivity analysis of a cavitation jet apparatus (CJA). This study employed an experimental platform that consisted of a vertical cylindrical test tank, a submerged nozzle, and an aluminum sample. By examining a range of orifice diameters, this research identified that smaller diameters led to increased erosion intensity, with the most pronounced effects observed at a diameter of 2 mm. Furthermore, various standoff distances (SoDs) were tested, which revealed that shorter distances resulted in greater erosion, with the highest impact noted at an SoD of 5 cm. This study also evaluated different nozzle geometries, where it was found that a 132° conical sharped edges nozzle, combined with an orifice diameter of 2 mm and an SoD of 5 cm, produced the most severe erosion. Conversely, chamfered edges nozzles and a commercial nozzle (MEG2510) with an SoD of 10 cm or greater showed reduced erosion. These results highlight that by standardizing the testing duration to 1200 s, the CJA could reliably assess the cavitation resistance of materials. This study established a clear relationship between increased pressure and higher impact forces, which led to more severe erosion. The findings underscore the effectiveness of the CJA in evaluating material resistance under various cavitation conditions, thus addressing a critical need for reliable cavitation testing tools. [ABSTRACT FROM AUTHOR]

Climate change and the gradual phaseout of the spruce from Central Europe inspired us to study the effects of the ageing process of trees on wood properties. This study was conducted in old tree stands with significant involvement of the spruce (Picea abies (L.) H. Karst) in the ages between 122 and 177 years. The study material (samples) was collected from the selected trees to study wood properties such as density, resilience to compressive strength, resilience to bending strength, and modulus of elasticity. The results and findings of this study indicate that the spruce currently reaches the optimal technical quality of wood tissue at approximately 60 years of age. It is approximately 20 years earlier than the planned cutting age for the species. This could be due to water stress which led to adaptive changes in the wood tissue and earlier technical maturation of the wood in the studied trees. Significant radiant variabilities of wood properties of the Norway spruce were observed. It was determined that wood density does not fully reflect its mechanical properties, and it can be considered an indicator of the technical quality of wood tissue, but only within a limited scope. The results obtained may not only be applied in optimising the use of wood from spruce stands. They can also indicate the need to change the approach to managing spruce stands and their conversion towards broadleaf species. [ABSTRACT FROM AUTHOR]

Polyolefin separators with worse porous structures and compatibilities mismatch the internal environment and deteriorate lithium-ion battery (LIB) combination properties. In this study, a sulfonated SiO2 (SSD) composited polypropylene separator (PP@SSD) is prepared to homogenize pore sizes and in situ-built SSD coatings on porous skeletons. Imported SSD uniformizes pore sizes owing to centralized interface distributions within casting films. Meanwhile, abundant cavitations enable the in situ SSD coating to facilely fix onto porous skeleton surfaces during separator fabrications, which feature simple techniques, low cost, environmental friendliness, and the capability for continuous fabrications. A sturdy SSD coating on the porous skeleton confines thermal shrinkages and offers a superior safety guarantee for LIBs. The abundant sulfonic acid groups of SSD endow PP@SSD with excellent electrolyte affinity, which lowers Li+ transfer barriers and optimizes interfacial compatibility. Therefore, assembled LIBs give the optimal C-rate capacity and cycling stability, holding a capacity retention of 82.7% after the 400th cycle at 0.5 C. [ABSTRACT FROM AUTHOR]

In this work emphasis was given to determine the evolution of the retained austenite phase fraction via X-ray diffractometry technique in the as-hardened AISI 440C martensitic stainless steel surface subjected to cavitation for increasing test times. Scanning electron microscopy results confirmed the preferential carbide phase removal along the prior/parent austenite grain boundaries for the first cavitation test times on the polished sample surface during the incubation period. Results suggest that the strain-induced martensitic transformation of the retained austenite would be assisted by the elastic deformation and intermittent relaxation action of the harder martensitic matrix on the austenite crystals through the interfaces between both phases. In addition, an estimation of the stacking fault energy value on the order of 15 mJ m−2 for the retained austenite phase made it possible to infer that mechanical twinning and strain-induced martensite formation mechanisms could be effectively presented in the studied case. Finally, incubation period, maximum erosion rate, and erosion resistance on the order of 7.0 h, 0.30 mg h−1, and 4.8 h μm−1, respectively, were determined for the as-hardened AISI 440C MSS samples investigated here. [ABSTRACT FROM AUTHOR]

The behaviour of bubbles in cavitation and boiling processes is determined by the thermodynamic parameters of the two-phase medium and the intensity of heat and mass transfer, which affect the final dynamic effects. In this review, we analyse the influences of these factors on bubble behaviour, as described in existing mathematical models. In particular, we analyse the physical processes that govern bubble behaviour, the influence of mass transfer, vapor and liquid temperature, vapour, and liquid pressure on the inertial and dynamic stages of development. In conclusion, we summarize the problems associated with modelling, the accuracy of numerical predictions, and propose directions for further research. [ABSTRACT FROM AUTHOR]

The erosion process of a 4 μm monolayer CrN coating deposited on 316L stainless steel due to cavitation was investigated using finite element analysis (FEA). To estimate load parameters from cavitation pit geometry resulting from high impact velocity and high strain rate, the explicit dynamic solver was employed. Water microjet impacts at velocities of 100, 200 and 500 m/s were simulated to recreate different cavitation erosion intensities observed in the experiment. The resulting damage characteristics were compared to previous studies on uncoated 316L steel. The relationship between impact velocity and postimpact geometry was examined. Simulations revealed that only impact at 500 m/s can exceed the maximum yield stress of the substrate without penetrating the coating. Subsequent impacts on the same zone deepen the impact pit and penetrate the coating, leading to direct substrate degradation. The influence of impact velocity on the coating degradation process is discussed. [ABSTRACT FROM AUTHOR]

Lead-Bismuth Eutectic (LBE) is an interesting candidate as a coolant for Generation IV nuclear power plants. Lead-bismuth lubricated radial guide bearing is the key component of the mechanical pump in a lead-bismuth coolant system. In this paper, the transient calculation model of multiphase lubrication flow field of journal bearing is established by using Singhal full cavitation model and structured dynamic grid technique. Due to the saturated vapors of LBE being very low, the effects of different Non-Condensable Gas (NCG) contents on the characteristics of lead-bismuth lubricated journal bearing systems were analyzed. The results show that the NCG content has an obvious influence on the working state of the bearing. With the increase in NCG content, the bearing load capacity decreases. Under the same load, with the increase in NCG content, the eccentricity of the static equilibrium position will be larger, which will increase the risk of bearing contact with the bearing bush. Moreover, the increase of NCG content will lead to the increase of tangential oil film force work, which is helpful to improve rotor stability. [ABSTRACT FROM AUTHOR]

Cavitation phenomena in pumps are major determinants of the lifespan of both the impeller and the pump itself, causing significant vibration and noise, which are critical concerns for pump designers. This study focuses on the influence of various geometric factors of the impeller, including the shape of the blade leading edge, blade inlet angle, number and thickness of blades, surface roughness, wrap angle, impeller outlet width, inlet hub diameter, and tip clearance. The pump analyzed in this study, which exhibited issues of vibration and noise in actual industrial settings, was evaluated by varying only the shroud diameter based on Gulich's theory, while keeping other parameters constant, to assess the effects on cavitation phenomena across five different impellers. Single-phase analysis was initially conducted to evaluate the performance of each pump model, with the reliability of the numerical analysis methods validated by comparison with experimental data. Furthermore, to analyze cavitation phenomena, a multiphase flow analysis was performed using the Rayleigh–Plesset model within a computational fluid dynamics framework. Quantitative analysis of cavitation occurrence, NPSH3% head-drop performance, and bubble volume was conducted. The results confirmed that the M1 model, featuring a shroud diameter of 560 mm, exhibited superior cavitation resistance. Variations in cavitation occurrence observed under three different flow conditions demonstrated a nonlinear trend, but overall, improvements were noted within a specific diameter range. This study offers valuable insights and data for pump design applicable in real-world industrial settings. [ABSTRACT FROM AUTHOR]

To study the effects of fluid compressibility on the dynamics of a cavitating vortex street flow in a regime where the vortex shedding frequency increases as a result of the cavitation increase, the cavitating wake behind a wedge was simulated employing both incompressible and compressible solvers. To do this, a compressible cavitation model was implemented, modifying the Zwart-Gerber-Belamri (ZGB) incompressible solver and including a pressure limit and absorbing boundary conditions to prevent a non-physical pressure field. To validate the performance of the compressible model, preliminary simulations were carried out on a 1D Sod cavitating tube and the cavitating vortex shedding behind a circular body at laminar flow conditions. The results of the cavitating wake behind the wedge with the incompressible and the compressible solvers showed similar predictions in terms of pressure, vortex shedding frequency, and instantaneous and average vapor volume fraction profiles. In spite of this, differences were obtained in the energy content of the fluid force fluctuations on the body at higher frequencies, which appear to be better resolved and amplified when the compressibility model is considered. Overall, both solvers provided comparable results in terms of cavitation phenomena that are well aligned with experimental observations. [ABSTRACT FROM AUTHOR]

This document discusses the study of two-phase flows, which are prevalent in natural phenomena and various engineering and industrial applications. Two-phase flows involve the interaction of two distinct phases within a system, leading to complex flow behaviors. Experimental studies of two-phase flows are challenging and expensive, but they are essential for validating computational fluid dynamics (CFD) models. The document also explores topics such as bubble dynamics, cavitation, and flow within channels. It highlights the challenges and advancements in CFD modeling and the integration of machine learning and deep learning techniques in fluid dynamics simulations. [Extracted from the article]

A novel polishing method is proposed to increase material removal rates through the acceleration of abrasive movements using micro-jets formed by spontaneous collapses of bubbles due to the cavitation in a special-shaped Venturi tube. The Venturi structure is optimized by numerical simulations. Process-related parameters for the optimal cavitation ratio are investigated for achieving maximum adaptation to polishing flat workpieces. Furthermore, this novel approach enhances processing efficiency by approximately 60% compared to traditional abrasive flow polishing. The processing method that employs cavitation bubbles within a special-shaped Venturi tube to augment the flow of abrasive particles holds significant potential for material polishing applications. [ABSTRACT FROM AUTHOR]

The circulation pump in a distillation column is a core device in a material circulation system, and its stable operation is crucial for the production process. The impeller of the circulation pump is prone to failure due to long-term contact with corrosive media, and subjected to a large amount of material erosion, which severely challenges the safety control of the distillation reaction system. Focusing on the corrosion failure phenomenon of circulation pump impellers, the failure mechanism was studied by means of macroscopic inspection, chemical composition analysis, metallographic examination, scanning electron microscopy (SEM), and energy dispersive spectrometer (EDS). Results indicated that the corrosion of circulation pump impellers was the result of the combined effects of surface wear, cavitation, and halogen element corrosion. The medium in contact with the impeller contained chloride ions, fluoride ions, and solid particles. During circulation pump operation, a low-pressure zone formed at the inlet, generating numerous water vapor bubbles. These bubbles burst in the high-pressure zone, creating highly localized impact forces. Combined with the abrasive action of solid particles on the impeller surface, this led to the destruction of the passivation film and the formation of numerous small pits. These corrosion pits and the surrounding environment formed micro-galvanic corrosion cells with small anodes and large cathodes. Under the accelerated corrosion caused by fluoride and chloride ions, the corrosion process towards the inner wall of the impeller intensified, ultimately leading to impeller failure. This study clarified the corrosion failure mechanism and its root causes in the 2507 duplex stainless steel circulation pump impeller and proposes corresponding improvement recommendations, providing a scientific basis for preventing similar issues from occurring in the future. [ABSTRACT FROM AUTHOR]

An analysis of the physical and chemical phenomena accompanying electrical discharges is carried out, and the main factors influencing microorganisms' abatement are studied. The similarity of the cavitation processes in water systems induced by underwater electric discharges and ultrasound is experimentally demonstrated. The characteristic features of electrical discharge in the cavitation mode, providing effective water disinfection with electric discharges with a significantly reduced amount of active chlorine, are identified in order of importance. The inactivation of microorganisms is intensified, firstly, by the generation of chemically active particles from the water medium itself, due to the integral action of the electro-discharge cavitation of the whole treated volume, and by local shock waves, acoustic flows, and ultraviolet radiation in the area near the cavitating bubbles. The main advantages of electric discharge cavitation over ultrasonic range are the wider range of high-frequency acoustic radiation inherent in an electric discharge, the high intensity and power of the cavitation processes, and the possibility of a significant increase in the volume of disinfected liquid. This study allows for a better understanding and prediction of the bacterial effects that occur during a high-voltage underwater electrical discharge. [ABSTRACT FROM AUTHOR]

Investigating the flow performance of Francis turbines from model to prototype is a complex but essential process for ensuring reliable and efficient turbine operation in hydropower plants. It ensures that Francis turbine designs operate efficiently under various operating conditions, extending from laboratory reduced-scale models to full-scale prototype installations. In this investigation, a Francis turbine model was tested under different operating conditions, and its properties were measured, including torque, hydraulic efficiency, power output, cavitation coefficient, rotational speed, flow rate, and pressure pulsations. The results of the Francis turbine model test indicate that it achieved the maximum torque with the designed discharge and designed head. The cavitation coefficient consistently remained higher than the critical cavitation coefficient. The initial cavitation bubbles were observed at 50% partial load but disappeared at full load. Pressure pulsations under different operating conditions showed the maximum peak-to-peak amplitude appearing at the turbine inlet domain and the minimum amplitude occurring at the draft tube elbow. A hill chart shows that the model's best efficiency was 93.66%, and the estimated best efficiency of the prototype was 95.03% at the design head. The conclusions and methodology of this study can be generalized to other similar hydraulic turbines, especially prototype Francis turbines that lack experimental results. [ABSTRACT FROM AUTHOR]

The occurrence of cavitation in marine propellers is a major source of noise in ships. Consequently, the occurrence and noise characteristics of cavitation must be better understood to control this issue. This study focuses on identifying the occurrence and noise characteristics of cavitating flow around two-dimensional (2D) hydrofoils. Using the commercial computational fluid dynamics software STAR-CCM+, a numerical analysis was conducted on the partial cavity flow occurring around 2D hydrofoils at specific angles of attack. In addition, the cavitation noise characteristics were analyzed by conducting a frequency analysis using the predicted pressure data obtained via a fluctuating pressure sensor positioned vertically above the hydrofoil. Consequently, the numerical results were compared with existing experimental data to validate the accuracy of the simulation. This study identifies the limitations of the Reynolds-averaged Navier–Stokes (RANS) method by closely comparing it with the large eddy simulation (LES) method for assessing noise characteristics in unsteady cavitating flow. Although RANS has limitations in qualitatively assessing periodic behavior compared to LES, it effectively predicts cavitation extent and is valuable for relative assessments in practical applications. [ABSTRACT FROM AUTHOR]

The dynamics of bubbles have garnered extensive interest among researchers both domestically and internationally due to their applications in engineering and military fields. The exploration of the mechanisms behind bubble loading, cavitation damage, and impact destruction has always been a focal point of study. However, in practical applications, bubbles often do not occur in isolation, and the interactions between multiple bubbles are highly complex. Therefore, this study investigates the pulsation characteristics of bubbles near rigid boundaries with multiple air bubbles attached in different spatial arrangements, focusing on the coupled pulsation phenomenon between cavitation clusters and bubbles. The research indicates that this coupled pulsation phenomenon is primarily influenced by the dimensionless distance parameter γs from the bubble to the boundary, the spacing γL between the air bubbles, and the spatial arrangement. Compared to Layout II, the bubble exhibits off-axis migration and jet direction only under Layout I conditions; for spatial Layout I, when the air bubble spacing γL is fixed, the displacement of the air bubble directly above the bubble is proportional to the distance parameter γs. This research underscores the potential for mitigating cavitation-induced damage through the strategic adhesion of multiple air bubbles. [ABSTRACT FROM AUTHOR]

The tensile stress generated by the superposition of two reflection waves in the target plays a critical role in explaining plate-impact-induced spalling. A method of images is proposed to simulate the physical process of wave superposition and this method is applied in order to study the cavitation mechanism in single-crystal Al through molecular dynamics simulation. The critical impact-load velocity for the cavitation obtained by this method is as small as 400 m/s, which is much lower than the result (650 m/s) obtained by the conventional piston-load method. The new cavitation mechanism found is distinctively different from the conventional dislocation-entanglement-induced cavitation under high-velocity impact. The new mechanism involves two key events: firstly, a crack-like defect is formed and its relevant atomic bonds are broken under high tensile stress, resulting in a great momentum of related atoms; and secondly, previous high-momentum atoms collide with the atoms in their running way, resulting in the destruction of the original FCC structure locally and nanovoids or penny-shaped voids being formed. Additionally, the cavitation region, the number of voids, and delamination surfaces increases with the impact-load rate. [ABSTRACT FROM AUTHOR]

In order to study the feasibility of forming microtexture at the surface of 7050 aluminum alloy by laser-induced cavitation bubble, and how the density of microtexture influences its tribological properties, the evolution of the cavitation bubble was captured by a high-speed camera, and the underwater acoustic signal of evolution was collected by a fiber optic hydrophone system. This combined approach was used to study the effect of the cavitation bubble on 7050 aluminum alloy. The surface morphology of the microtexture was analyzed by a confocal microscope, and the tribological properties of the microtexture were analyzed by a friction testing machine. Then the feasibility of the preparation process was verified and the optimal density was obtained. The study shows that the microtexture on the surface of a sample is formed by the combined results of the plasma shock wave and the collapse shock wave. When the density of microtexture is less than or equal to 19.63%, the diameters of the micropits range from 478 μm to 578 μm, and the depths of the micropits range from 13.56 μm to 18.25 μm. This shows that the laser-induced cavitation bubble is able to form repeatable microtexture. The friction coefficient of the sample with microtexture is lower than that of the untextured sample, with an average friction coefficient of 0.16. This indicates that the microtexture formed by laser-induced cavitation bubble has a good lubrication effect. The sample with a density of 19.63% is uniform and smooth, having the minimum friction coefficient, with an average friction coefficient of 0.14. This paper provides a new approach for microtexture processing of metal materials. [ABSTRACT FROM AUTHOR]

The geometry of an orifice is a major determinant of nozzle internal flow and cavitation, which directly govern spray atomization and consequently affect combustion and fuel economy in internal combustion engines. In this study, simulation models of the nozzle at different angles between the normal and the injection hole inlet cross-section and the injection hole axis, as well as with different injection hole cone angles (a positive angle between the injection hole axis and its walls implies a divergent hole), were investigated by means of a previously developed numerical model that was validated based on experimental data from X-ray image technology. The results indicate that as the angle between the normal and the injection hole inlet cross-section and the injection hole axis increases, the cavitation asymmetry within the injection hole intensifies, accompanied by a decrease in the gas volume fraction. On one side of the injection hole, the hydraulic flip width expands, while, on the other side of the injection hole, the flow state gradually changes from hydraulic flip to super-cavitation flow, transitional cavitation and fully reattached flow. The divergent orifice layout intensifies cavitation, and the higher the positive injection hole cone angle, the bigger the hydraulic flip width. The convergent layout of the injection hole suppresses cavitation, and cavitation inside the nozzle disappears completely when the injection hole cone angle is less than −10°. [ABSTRACT FROM AUTHOR]

The current study aims to degrade Procion Golden Yellow H-R through ultrasound-induced cavitation coupled with various oxidants. A comprehensive investigation was conducted to examine the impact of parameters, specifically pH, power, and frequency, on the extent of degradation. The primary aim was to optimize degradation by solely utilizing a cavitation reactor where only 23.8% degradation was observed under the established optimum conditions of pH 2.5, frequency of 22 kHz, and power of 200 W. The investigation of the combined process of cavitation with H2O2, Fenton reagent (H2O2/Fe2+), NaOCl, and potassium persulphate (KPS) was subsequently conducted under optimized conditions. The combined operations greatly enhanced degradation with the use of H2O2 loading of 0.1 g/L leading to 53.3% degradation and the H2O2/Fe2+ ratio of 1:0.25 resulting in 94.6% degradation, while the NaOCl quantum of 0.075 g/L yielded 90% degradation and the KPS quantity of 2 g/L resulted in 97.5% degradation in the specific combinations. A toxicity test on two bacterial strains, Staphylococcus aureus and Escherichia coli, was carried out using the original dye solution and after treatment. The various individual and combination processes were compared using the parameters of cavitational yield and total treatment cost. The study elucidates that combining ultrasonic cavitation with KPS is an effective method for treating wastewater containing Procion Golden Yellow H-R dye, especially when implemented at a larger scale of operation. [ABSTRACT FROM AUTHOR]

Bisphenol A (BPA) is an environmental endocrine-disrupting compound that is resistant to conventional biological treatment, making it crucial to develop an oxidation process. This study introduces a novel hydrodynamic cavitation (HC) coupled with a Fenton + periodate (PI) oxidation system for the efficient degradation of BPA. By systematically examining the key parameters such as inlet pressure, Fe (II), H2O2, and PI concentration, it was found that HC performed optimally at a pressure of 0.5 MPa. A conversion of 98.14% was achieved within 60 min when the molar ratio of BPA, Fe (II), H2O2, and PI was approximately 1:1:5:1. Further analysis revealed that the gray correlation between H2O2 and PI concentrations on the degradation efficiency was 0.833 and 0.843, respectively, indicating that both of them had significant effects on the degradation process. The free radical quenching assay confirmed the hydroxyl radical (•OH) as the main active substance. Additionally, the toxicity of the degradation intermediates was evaluated using the Toxicity Estimation Software Tool (TEST). An artificial neural network (ANN)-based model was constructed to predict the BPA-degradation process, facilitating precise reagent dosing and providing robust support for the intelligent application of water-treatment technologies. [ABSTRACT FROM AUTHOR]

With the increasing demand for deep oil and gas exploration and CCUS (Carbon Capture, Utilization, and Storage) engineering, improving rock-crushing efficiency stands as a pivotal technology. Ultrasonic vibration-assisted drilling has emerged as a novel rock-breaking technology. The high-frequency vibrations of ultrasonic waves impact rocks, inducing resonance and accelerating their fragmentation. At the same time, ultrasonic waves generate cavitation bubbles in the liquid near rock surfaces; the expansion and collapse of these bubbles further contribute to rock damage, thereby improving crushing efficiency. Therefore, investigating the dynamics and failure characteristics of cavitation bubbles near rock surfaces under ultrasonic influence is crucial for advancing ultrasonic-assisted rock-breaking technology. This study treats the liquid as compressible flow and investigates the movement and rupture of bubbles near rock surfaces under varying ultrasonic parameters, rock properties, characteristics of the circulating medium, and other relevant factors. The findings show that ultrasonic waves induce the oscillation, translation, collapse, and rebound of bubbles near rock surfaces. Higher ultrasonic frequencies correspond to larger collapse pressures and amplitudes near surrounding rocks, as well as longer expansion times and shorter collapse durations. In addition, bubble movement and collapse lead to rock material deformation, influenced by the rheological properties of the liquid medium. The study outcomes serve as a foundation for optimizing engineering parameters in ultrasonic-assisted rock breaking and provide theoretical support for the advancement of this technology. [ABSTRACT FROM AUTHOR]

The rapid development of industrial and information technology is driving the demand to improve the applicability and hydraulic performance of centrifugal pumps in various applications. Enhancing the rotational speed of pumps can simultaneously increase the head and reduce the impeller diameter, thereby reducing the pump size and weight and also improving pump efficiency. This paper reviews the current application status of high-speed pumps using low-temperature thermosensitive fluids, which have been applied in fields such as novel energy-saving cooling technologies, aerospace, chemical industries, and cryogenic engineering. Due to operational constraints and thermal effects, there are inherent challenges that still need to be addressed for high-speed pumps. Based on numerical simulation and experimental research for different working fluids, the results regarding cavitation within the inducer have been categorized and summarized. Improvements to cavitation models, the mechanism of unsteady cavity shedding, vortex generation and cavitation suppression, and the impact of cavitation on pump performance were examined. Subsequently, the thermal properties and cavitation thermal effects of low-temperature thermosensitive fluids were analyzed. In response to the application requirements of pump-driven two-phase cooling systems in data centers, a high-speed refrigerant pump employing hydrodynamic bearings has been proposed. Experimental results indicate that the prototype achieves a head of 56.5 m and an efficiency of 36.1% at design conditions (n = 7000 rpm, Q = 1.5 m3/h). The prototype features a variable frequency motor, allowing for a wider operational range, and has successfully passed both on/off and continuous operation tests. These findings provide valuable insights for improving the performance of high-speed refrigerant pumps in relevant applications. [ABSTRACT FROM AUTHOR]

Coalbed methane (CBM), recognized as a sustainable and environmentally friendly energy source, plays a crucial role in mitigating global climate change and advancing low-carbon energy solutions. However, the prevalence of low-permeability coal seams poses a significant challenge to effective CBM extraction. Improving coal permeability has emerged as a viable strategy to address the issue of low-permeability coal. Conventional CBM stimulation methods fall short in overcoming this obstacle. In contrast, the enhanced technique of CBM extraction by water-based ultrasonic cavitation holds great promise due to its use of high energy intensity, safety, and efficiency. Nevertheless, the inadequate theoretical framework for managing this technology impedes its widespread adoption for large-scale applications. This study investigated the impact of water-based ultrasonic cavitation treatment on coal's properties and permeability through mechanical testing and permeability measurements conducted before and after treatment. This study also explored the process by which this technology, known as WUC-ECBM, improves coal's mechanical properties and permeability. The findings suggest a potential stimulation technique (WUC-ECBM) for use in CBM extraction, and its physical mechanism. [ABSTRACT FROM AUTHOR]

An inducer is a key component in a cryogenic pump to improve its cavitation performance. The thermodynamic effects of the cryogenic medium make the cryogenic cavitation flow extremely complicated. For this reason, it is crucial to investigate the cryogenic cavitation flow of the inducer which is equipped upstream of the cryogenic pump. In this paper, the isothermal cavitation model is modified based on the law of heat conduction, and the cryogenic cavitation model of the inducer is developed by considering thermodynamic effects. The turbulence model is also modified to account for the compressibility of cryogenic cavitation flow. The methods of numerical calculations are performed to investigate the influence of thermodynamic effects on cryogenic cavitation of the inducer. The law of the spatio-temporal evolution of cryogen cavitation in the inducer is clarified. The initial position, development and collapse phenomenon of cavitation are obtained. The relationship between the generation and collapse of the cavitation and the work capacity of the inducer's blade, the relationship between thermodynamic effects and the influence of the inducer's blade tip leakage vortex and thermodynamic on cryogenic cavitation of the inducer are revealed. [ABSTRACT FROM AUTHOR]

Nucleation is a fundamental and general process at the initial stage of first-order phase transition. Although various models based on the classical nucleation theory (CNT) have been proposed to explain the energetics and kinetics of nucleation, detailed understanding at nanoscale is still required. Here, in view of the homogeneous bubble nucleation, we focus on cavity formation, in which evaluation of the size dependence of free energy change is the key issue. We propose the application of a formula in stochastic thermodynamics, the Jarzynski equality, for data analysis of molecular dynamics (MD) simulation to evaluate the free energy of cavity formation. As a test case, we performed a series of MD simulations with a Lennard-Jones (LJ) fluid system. By applying an external spherical force field to equilibrated LJ liquid, we evaluated the free energy change during cavity growth as the Jarzynski's ensemble average of required works. A fairly smooth free energy curve was obtained as a function of bubble radius in metastable liquid of mildly negative pressure conditions. [ABSTRACT FROM AUTHOR]

Some high-specific-speed centrifugal pumps exhibit instability in terms of hydraulic performance and cavitation characteristics, and there's a lack of reliable numerical models to guide the optimization of cavitation instability. This paper, by conducting a study on mesh independence, analyzes the cavitation curves and cavitation counters for various mesh combinations in the numerical model, The findings indicate that the boundary layer grid not only influences the location of peak points but also the size of the peak. To achieve a stable NPSH peak position, the y+ at the blade leading edge of high-specific-speed centrifugal pumps needs to be controlled between 20–80. The turbulence model, evaporation coefficient, and condensation coefficient were simulated using the orthogonal experimental design method, analyzing the impact of these parameters on the NPSH peak. A visual high-speed photography test rig was established, and rotating cavitation and sheet cavitation is found at part-load. By comparing the cavitation and pressure counters with high-speed photography images, a numerical model was obtained that closely mirrors the experimental cavitation characteristics. [ABSTRACT FROM AUTHOR]

In order to obtain a more detailed and comprehensive relationship between the cavitation phenomenon and energy loss, this paper takes an NACA66 hydrofoil as an example to analyze the specific relationship between the cavitation flow field and energy dissipation by using entropy production theory, a ZGB cavitation model, and k-ε turbulence model which were modified by a Filter-Based Density Correction model (FBDCM). The results show that the modified k-ε model can effectively capture the morphology of cavity evolution in the cavitation flow field. The vortex dilatation term contributes the most to the vorticity transport in cavitation flow. The energy loss of the cavitation flow field is primarily composed of turbulent dissipation, which is primarily distributed in the area below the lifted attached cavity and inside the vortex induced by the cloud cavity. The direct dissipation entropy production is predominantly distributed in the area near the stagnation point of the hydrofoil's leading edge and inside the cavity. The wall entropy production is chiefly distributed in the area where the cavity is not covered. The cavitation entropy production mainly occurs on the vapor–liquid interface, and the value is negative, indicating that the vapor–liquid conversion in the cavitation process needs to absorb energy from the flow field. [ABSTRACT FROM AUTHOR]

Coal seam cavitation is one of the most effective techniques for gas disaster control in low-permeability coal. Due to the difference in cavitation method and process, the damage degree and fracture development range of the coal body around the cavern are greatly different, and the effect of increasing the permeability of the coal body is further changed. In order to further understand the permeability enhancement mechanism of cavitation technology on low-permeability coal and effectively guide engineering applications, this paper conducted experimental research on the unloading damage and permeability evolution characteristics of coal under different cavitation paths using a coal-rock "adsorption-percolation-mechanics" coupling test system. Through the analysis of coal strength and deformation characteristics, coal damage characteristics, and the evolution law of coal permeability combined with the macroscopic damage characteristics of coal, the strength degradation mechanism of unloaded coal and the mechanism of increased permeability and flow were revealed. The results show that unloading can significantly reduce the strength of coal, and the greater the unloading rate, the more obvious the reduction. The essence of this is that unloading reduces the cohesion and internal friction angle of coal—damage and breakage are the most effective ways to improve the permeability of the coal body. Unloading damaged coal bodies not only significantly improves the permeability of the coal body but also improves the diffusion ability of gas, and finally, shows a remarkable strengthening effect of gas extraction. [ABSTRACT FROM AUTHOR]

The current research investigates the effects of materials and riblets on cavitation-induced erosion morphology, depth, and cross-sectional area through experimental approaches. To achieve these aims, the erosion of pure aluminum (1xxxAl or Al) and alpha brass (CuZn37 or CZ108), in the presence and absence of bio-inspired sawtooth riblets, was examined after exposure to multiple collapses of single cavitation bubbles with a wall distance of 1.8 (dimensionless). The results indicate that the erosion morphology resembles a rounded cone with a circular cross-section. Brass provides 21.6% more erosion resistance compared to that of Al in terms of material properties. Furthermore, the erosion for both Al (depth by 3.8% and width by 18.3%) and brass (depth by 7.9% and width by 27.4%) decreases in the presence of riblets compared to the results for flat surfaces. The greater erosion resistance of brass compared to Al is attributed to the superior mechanical stability of brass, making it a potentially suitable alloy for use in propellers and hulls in the shipping industry. In summary, the results reveal that riblet-equipped materials with high mechanical durability are promising erosion-resistant materials for the shipping industry. However, the potential for chemical reactions in a cathodic environment should be addressed to provide a comprehensive perspective in regards to reducing corrosion intensity. [ABSTRACT FROM AUTHOR]

This study investigates cloud cavitation suppression around a model-scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift–drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor–liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift–drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide a valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems. [ABSTRACT FROM AUTHOR]

The presence of gas in transmission fluid can disrupt the flow continuity, induce cavitation, and affect the transmission characteristics of the system. In this work, a gas void fraction model of gas–liquid two-phase flow in a transmission tube is established by taking ISO 4113 test oil, air, and vapor to accurately predict the occurrence, development, and end process of the cavitation zone as well as the transient change in gas void fraction. This model is based on the conservative homogeneous flow model, considering the temperature change caused by transmission fluid compression, and cavitation effects including air cavitation, vapor cavitation, and pseudo-cavitation. In this model, the pressure term is connected by the state equation of the gas–liquid mixture and can be applied to the closed hydrodynamic equations. The results show that in the pseudo-cavitation zone, the air void fraction decreases rapidly with pressure increasing, while in the transition zone from pseudo-cavitation to air cavitation, the air void fraction grows extremely faster and then increases slowly with decreasing pressure. However, in the vapor cavitation zone, the vapor void fraction rises slowly, grows rapidly, and then decreases, which is consistent with the explanation that rarefaction waves induce cavitation and compression waves reduce cavitation. [ABSTRACT FROM AUTHOR]