Search

As a green and low-carbon natural polymer material, wood has always been popular in engineering applications owing to its excellent physical and mechanical properties. In this study, compression tests in conjunction with in situ test methods (DIC method) were used to investigate the compression mechanism of wood samples in the longitudinal, radial, and tangential directions. The macroscopic failure modes, energy dissipation results, and variations in the strain field were analyzed. The results showed that the load–displacement curve in each grain orientation included three stages: an elasticity stage, yield stage, and strengthening stage. Both the compressive strength and elastic modulus in the longitudinal direction were significantly higher than those in the radial and tangential directions, but there was no significant difference between the radial and tangential directions. Specimens in the longitudinal direction mainly presented fiber buckling, fiber shear slippage, and fiber fracture failure; in radial directions mainly presented compression compaction of the fiber cells; and in the tangential directions presented buckling and shear failure of the laminar layers. The energy absorption in the longitudinal direction was better than in the other directions. The strain changed significantly in the loading direction in the elastic stage while the shear strain changed remarkably in the yield stage in each grain orientation. In this paper, the compression mechanical properties of larch wood in different grain orientations were studied to provide a reference for its safe application in engineering. [ABSTRACT FROM AUTHOR]

Fretwork, as a decorating technique, can today be performed with modern means by laser or CNC routing, but the tool influence on the surface quality must be well understood for further optimization of the cutting parameters. The paper presents an experimental work for the determination of the influence of the cutting angle with respect to the grain on the surface quality of larch wood (Larix decidua Mill.) cut through by laser and CNC routing at different feed speeds. The research considered geometric fretwork patterns derived from triangle, where the cutting angles with respect to the wood grain were 0°, 15°, 30°, 45°, 60°, 75° and 90°. The feed speeds of the CNC routing were set for 2, 2.5, 3, 3.5 and 4 m/min. The surface quality was analyzed by a range of roughness, waviness and primary profile parameters combined with stereomicroscopic images. Although the principle of cutting and interaction with wood of the two processing tools, laser and CNC, is very different, the analysis with roughness parameters has revealed that the cutting angle with respect to the grain has an essential influence, whatever the cutting tool. The surface quality decreases with an increase in the feed speed of the CNC router and processing at 15° and 60° appears to be the worst option from all angle variants for both types of processing. Cutting by laser is melting wood in latewood areas resulting in a smoothing effect. [ABSTRACT FROM AUTHOR]

Arctic driftwood has reached the coast of Iceland for centuries. This material was used by the inhabitants of the island as a building material for houses, boats, churches and pasture fences. Nowadays, the driftwood is used in the furniture industry, for the finishing of internal and external walls of buildings and also by artists. The properties of driftwood differ to that of original resource due the long-term effects of exposure to Arctic Sea water and ice. This process can be considered as a natural modification, even if its effect on various wood properties and the potential use of driftwood are not yet fully understand. This research is focused on the comparison of cutting forces measured for Siberian larch (Larix sibirica L.) from Siberia provenance and driftwood found on the coast of Iceland. The cutting forces were determined directly from the cutting power signal that was recorded during the frame sawing process. A new procedure for compensation of the late/early wood ratio variation within annual rings is proposed to homogenize mechanical properties of wood. It allows a direct comparison of machinability for both types of larch wood investigated (driftwood and natural). Noticeable differences of normalized cutting force values were noticed for both wood types, which were statistically significant for two set values of feed per tooth. These results provide a new understanding of the effect of the drifting process in the Arctic Sea (natural modification) on mechanical and physical properties of wood. Such a natural modification may influence transformation processes of driftwood as well as performance of the coating systems applied on its surface. [ABSTRACT FROM AUTHOR]

Reducing discoloration of wood due to photodegradation caused by ultraviolet (UV) and visible (VIS) radiation enhances its aesthetical value and prolongs the overall service life of protective coatings. In this study, the efficiency of pretreatments with different active ingredients to reduce degradation and stabilize the color of Siberian (Larix sibirica Ledeb.) and European larch (Larix decidua Mill) wood was investigated. UV absorbers (UVA), hindered amine light stabilizers (HALS) and zinc oxide nanoparticles were used in twenty different pretreatments. The ability to protect wood surface against radiation was evaluated via color and gloss change measurements during artificial ageing. The efficiency of tested color-stabilizing pretreatments differed for Siberian and European larch and not all of them reduced discoloration. The most effective pretreatments were based on a combination of UVA and HALS in a synergistic effect. Overall, the best efficiency from tested variants for larch wood generally was observed for combination of Eversorb 80 on benzotriazole basis + Eversorb 93 on a piperidinyl basis. The pretreatments did not significantly affect the gloss values. The results revealed convenient variants of stabilizers for Siberian and European larch wood and confirmed different compatibility between specific wood species and color stabilizers. [ABSTRACT FROM AUTHOR]

This paper compares the resistance of 20 commercial transparent and semi-transparent coatings applied to European and Siberian larch during artificial weathering in Xenotest. The change in gloss, colour, contact angle of wetting, resistance to Aspergillus niger and Penicillium brevicompactum moulds was evaluated, and visual changes at the top surface of treated wood species were measured. Overall, the durability of coatings on European larch was higher than that on Siberian larch. The most durable of the tested coatings was a thin-film, i.e., semi-transparent oil-based film containing TiO2 pigment and propiconazole fungicide. Of the transparent coatings, the most stable was a thick acrylic coating. Conversely, penetrating transparent oil systems had low colour stability and overall lifespan. Artificial weathering of all of the coatings resulted in a marked decrease in their resistance to moulds. [ABSTRACT FROM AUTHOR]