Search

Nanofiber mats with a high surface-to-volume ratio can be prepared by electrospinning. The Porosity is sometimes reported to be tunable by blending different materials, e.g., water-soluble poly(ethylene oxide) (PEO) with not water-soluble poly(acrylonitrile) (PAN). Here, nanofiber mats were electrospun from different PAN:PEO ratios, using a wire-based electrospinning machine "Nanospider Lab". Investigations of the as-spun nanofiber mats as well as of membranes after washing off the water-soluble PEO by scanning electron microscopy (SEM) revealed severe differences in the nanofiber mat morphologies, such as varying fiber diameters and especially non-fibrous areas in the carbonized nanofiber mats, depending on the amount of PEO in the nanofiber mat as well as the molecular weight of the PEO. Similarly, the ratio and molecular weight of PEO influenced the results of stabilization and carbonization. This paper discusses the possibility of tailoring nanofiber porosity for the potential use of PAN nanofiber mats in tissue engineering, filtration, and other applications. [ABSTRACT FROM AUTHOR]

In recent years, the global production and industrialization of avocados has led to the generation of large numbers of peel, seeds, and leaf by-products with significant environmental implications. Current efforts, including the Sustainable Development Goals, aim towards the development of sustainable operations through the valorization of waste. Previous research has focused on studying the rich chemical composition of these avocado by-products. Current studies are working on the isolation of polyphenols, flavonoids, phenolic acids and other bioactive compounds found in avocado peel, seeds and leaves for applications in nutraceutical products in the food, pharmaceuticals and cosmetics industries. The inclusion of these extracts in industrial matrices often requires stabilization technologies such as encapsulation emulsions to ensure the delivery and bioactivity of these target compounds. This review will discuss the global production volumes of avocado and its by-products as well as the potential inclusion in various industries based on their chemical compositions. Additionally, this work addresses the various applications that have been previously proposed for the wastes and their extracts. This review also covers the stabilization techniques previously employed in avocado extract treatment, their applications, and the current challenges and opportunities associated with avocado by-products. [ABSTRACT FROM AUTHOR]

This study focuses on the preparation of activated carbon using a petroleum-residue-based pitch, as well as the HCl gas adsorption properties of the resulting activated carbon pellets relative to their specific surface area and pore structure. Activated carbon was prepared under various oxidation and chemical activation conditions using pitch with a softening point of 220 °C. The activated carbon was mixed with distilled water, an acrylic binder, and carboxymethyl cellulose in a specific ratio to form pellets. These pellets were then dried in an oven at 80 °C. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Brunauer–Emmett–Teller analyses were performed to evaluate the surface structure and specific surface area of the finalized pellets. HCl gas was adsorbed at a concentration of 50 ppm while examining the adsorption characteristics relative to the pore structure and specific surface area. [ABSTRACT FROM AUTHOR]

Sewage sludge (SS), a byproduct of wastewater treatment plants, poses significant environmental and health risks if not properly handled. Conventional approaches for SS stabilization often involve costly and energy-consuming processes. This study investigated the effect of promoting native microalgae growth in SS on its stabilization, pathogen bacteria removal, and valuable biomass production. The effect on settleability, filterability, and extracellular polymeric substances (EPSs) was examined as well. Experiments were conducted in photobioreactors (PBRs) without O2 supply and CO2 release under controlled parameters. The results show a significant improvement in SS stabilization, with a reduction of volatile solids (VSs) by 47.55%. Additionally, fecal coliforms and E. coli were efficiently removed by 2.25 log and 6.72 log, respectively. Moreover, Salmonella spp. was not detected after 15 days of treatment. The settleability was improved by 71.42%. However, a worsening of the sludge filterability properties was observed, likely due to a decrease in floc size following the reduction of protein content in the tightly bound EPS fraction. Microalgae biomass production was 16.56 mg/L/day, with a mean biomass of 0.35 g/L at the end of the batch treatment, representing 10.35% of the total final biomass. These findings suggest that promoting native microalgal growth in SS could be sustainable and cost-effective for SS stabilization, microalgal biomass production, and the enhancement of sludge-settling characteristics, notwithstanding potential filtration-related considerations. [ABSTRACT FROM AUTHOR]

Chitosan, a naturally occurring biopolymer derived from chitin, has emerged as a highly promising instrument for the production and application of metal nanoparticles. The present review delves into the several functions of chitosan in the development and operation of metal nanoparticles, emphasizing its aptitudes as a green reducing agent, shape-directing agent, size-controlling agent, and stabilizer. Chitosan's special qualities make it easier to manufacture metal nanoparticles and nanocomposites with desired characteristics. Furthermore, there is a lot of promise for chitosan-based nanocomposites in a number of fields, such as metal removal, water purification, and photoacoustic, photothermal, antibacterial, and photodynamic therapies. This thorough analysis highlights the potential application of chitosan in the advancement of nanotechnology and the development of medicinal and environmental solutions. [ABSTRACT FROM AUTHOR]

The deterioration of dams and levees is an increasing concern for both infrastructure integrity and environmental sustainability. The extensive repercussions, including the displacement of communities, underscore the imperative for sustainable interventions. This study addresses these challenges by investigating the stabilization of dredged material (DM) for diverse applications. Seven mixtures incorporating fly ash, lime, and cement were formulated. The Standard Compaction Test was used to determine optimal density–moisture conditions, which helped with brick fabrication. Bricks were tested for compressive strength over various curing periods, and the durability of the 28-day-cured samples was evaluated by performing water immersion tests following the New Mexico Code specifications. Scanning electron microscopy (SEM) was used to assess microstructural bonding. Results confirm that the inclusion of cementitious stabilizers modifies the material's microstructure, resulting in enhancements of both strength and water resistance. Notably, the stabilized material demonstrates potential for use in non-fired brick manufacturing and as bridge stones for waterway erosion control. This dual-function application offers a sustainable and economically feasible approach to managing dredged materials. [ABSTRACT FROM AUTHOR]

The risk posed by expansive soils can be lessened by placing foundations at a more deep level below the surface. Structures are able to withstand uplift forces because overburden pressure partially suppresses swelling pressure. In order to transfer the forces to a sufficiently deep depth, this study suggests introducing shafts of a low-expansion overburden material. Soil improved with cement is chosen for this purpose. This study suggests using sand with added excavated natural clay and cement. The expansive clay is added to sand in ratios of 10, 20, 30, 40 and 60%. The clay–sand mixture is then enhanced by cement of 1, 2, 4 and 8% by the weight of the mixture under four curing periods of 1, 7, 28, and 90 days. This material is recommended for use under lean concrete to transfer the loads to lower levels below the foundation depth. The thickness of this material depends on the stresses exerted, the type and the properties of the subsurface soils. The cement-enhanced clay–sand shaft's properties are examined in this work with regard to the swelling potential, compressibility, and the unconfined compressive strength for different clay contents and curing conditions. Stiff shafts were formed and found to support stresses from 600 to 3500 kPa at cement additions in the range of 1% to 8%. Clay content above 30% is found to be not suitable for Al-Qatif clay due to the compressibility and low strength of the mixture. When two percent or more of cement is added, the swelling potential is significantly reduced. This is reliant on the pozzolanic interactions of soils and cement as well as the clay mineralogy. Determining how cement affects clay–sand combinations in regions with expansive soils would facilitate the introduction of a novel, inexpensive technology to support loads applied by the superstructure. [ABSTRACT FROM AUTHOR]

Arsenic contamination of various environmental components poses a serious threat to human and animal health. Soil As contamination is particularly hazardous, as soil is a vital pathway to the food chain. We conducted experiments on soil from a typical pharmaceutical and chemical industry relocation site in Hubei Province, focusing on modification using fly ash through mechanical and chemical mechanisms. We subjected varying proportions of lime, ferrous sulfate, and fly ash to mechanical ball milling and used these mixtures to perform remediation of arsenic-contaminated soil and site restoration. Our findings are as follows: in soil culture experiments, the As stabilization efficiency reached 90% within 90 days with ferrous salt-modified fly ash. In actual site restoration, As-stabilization efficiency exceeded 95% across different soil depths within 30 days, demonstrating significant stabilization effects. Optimal modified dosages were determined as 2% ferrous sulfate and 2% fly ash. After stabilization, As in the soil primarily existed in amorphous iron-aluminum oxide-bound (F3) and crystalline iron-aluminum oxide-bound (F3 + F4) and residual (F5) states. Fluctuations in the moisture content and pH mainly activated F3 and F4, transitioning them into exchangeable (F1) and surface-adsorbed (F2) states. Arsenic leaching was predominantly associated with the F1 form. Fly ash-based restoration technology demonstrates promising capabilities in waste treatment and pollution control, offering significant potential for widespread application. [ABSTRACT FROM AUTHOR]

Background: ATTR-CM is becoming more prevalent, and disease-modifying therapy has been investigated in recent years with promising results. Diflunisal has shown TTR-stabilizing properties assessed by biomarkers and echocardiography, but there are no trials addressing the evolution of morphological changes with CMR. Methods and Results: AMILCA-DIFLU is an exploratory pilot study prospective, single-center, non-randomized, open-label clinical trial. Patients diagnosed with ATTR-CM underwent clinical, functional, biochemical and imaging assessment before and one year after diflunisal therapy initiation. Of the twelve ATTR-CM patients included, only nine patients completed treatment and study protocol in 12 months. To increase the sample size, we included seven real-world patients with one year of diflunisal treatment. Among the group of patients who completed treatment, diflunisal therapy did not show improvement in cardiac disease status as assessed by many cardiac and inflammatory biomarkers, 6MWT and CMR parameters after one year of treatment. However, a non-significant trend towards stabilization of CMR parameters such as LVEF, ECV and T2 at one year was found. When comparing the group of patients who completed diflunisal therapy and those who did not, a significant decrease in the distance performed in the 6MWT was found in the group of patients who completed treatment at one year (−14 ± 81.8 vs. −173 ± 122.2; p = 0.032). Diflunisal was overall well tolerated, showing only a statistically significant worsening in renal function in the group of diflunisal-treatment patients with no clinical relevance or need for treatment discontinuation. Conclusions: In patients with ATTR-CM, treatment with diflunisal was overall well tolerated and tended to stabilize or slow down amyloid cardiac disease progression assessed by CMR parameters, cardiac and inflammatory biomarkers and functional capacity. [ABSTRACT FROM AUTHOR]

Horses have been companions of people for thousands of years. Areas in which humans use these animals include, for example, transport, participation in sports competitions, or during rehabilitation (hippotherapy). Unfortunately, injuries such as lower limb fracture very often require euthanasia due to the significant difficulties in conducting fracture therapy/repair. Therefore, there are still many possibilities for the improvement of existing treatments. The aim of the study was to conduct a numerical analysis enabling the prediction of bone union of the third metacarpal bone of a horse. The loading conditions and type of fracture were based on a pony weighing 120 kg; however, research on a live animal was not the purpose of this study. Numerical studies were carried out for three different methods of stabilization using bone plates in the Ansys program (lateral, anterior, and lateral–anterior stabilization). An algorithm based on the Carter model was used to predict bone union, while linear-coupled models were used to describe the behaviour of materials. The authors also performed dynamic analyses in the Abaqus/Explicit program to determine the maximum speed at which the horse could move so that the fracture would not deepen. For dynamic analyses, the authors used nonlinear models—Johnson–Cook in the case of the 316L surgical steel material and cortical bone. Material failure was described using the Johnson–Cook failure model for steel and the limit strain model for cortical bone. A series of numerical simulations allowed to determine the direction of bone union building, and the most favourable case of stabilization was determined. [ABSTRACT FROM AUTHOR]

The prolonged duration of phytoremediation poses a risk of heavy metal dispersal to the surrounding environment. This study investigated a combined remediation approach for cadmium (Cd)- and arsenic (As)-contaminated soil by integrating phytoremediation with stabilization techniques. Bidens pilosa was utilized as the phytoremediator, and steel slag, pyrolusite, and FeSO4 were employed as stabilizing agents in the pot experiments. Key metrics such as soil moisture content, root length, plant height, and heavy metal concentrations in Bidens pilosa were measured to evaluate the remediation efficacy. Additionally, the bioavailability, leaching toxicity, and chemical forms of Cd and As, along with other soil properties, were analyzed. The results indicated that the optimal restoration effect was achieved by combining steel slag, pyrolusite, and FeSO4 with stabilizers in a ratio of 2:1:10. Additionally, the optimal dosage of these materials was found to be 9% by weight. Mechanistic studies, including heavy metal speciation analysis, X-ray photoelectron spectroscopy (XPS), and microbial community diversity analysis, revealed that the stabilization effects were primarily due to the interactions of anionic and cationic ions, chelation by organic acids secreted by plant roots, and enhanced microbial activity. A cost–benefit analysis demonstrated the technical, economic, and commercial viability of the combined remediation approach. [ABSTRACT FROM AUTHOR]

To seek an appropriate stabilization and remediation scheme for cadmium (Cd) and arsenic (As) pollution in farmland, a typical polluted soil sample was selected from a mining area in Southwest China for a soil box simulation experiment. Biochar (BC), a modified type of biochar made from rice husk with different mass ratios of ferric chloride and rice husk, was set up (the mass ratio of ferric chloride to rice husk was 1:9 (defined as LFB), 3:7 (defined as MFB), and 5:5 (defined as HFB) and the control group (BL)) to explore the effects of soil water and fertilizer loss, the bioavailability of Cd and As, and the bioenrichment effects of plant organs during the growth period of rice. The results showed that the porous structure and large specific surface area of biochar effectively regulated soil aggregate composition and improved soil water holding capacity. Compared to the BL treatment, soil water storage under the four carbon-based material control modes increased from 8.98% to 14.52%. Biochar has a strong ion exchangeability and can absorb soil ammonium, nitrogen, and phosphoric acid groups, effectively inhibiting the loss of soil fertilizer. Biochar improves soil pH and reduces the specific gravity of exchangeable Cd. In addition, the oxygen-containing functional groups in biochar can react with metals in a complex manner. The diethylenetriaminepentaacetic acid (DTPA) concentrations of Cd in soils treated with BC, LFB, MFB, and HFB were 79.69%, 72.92%, 64.58%, and 69.27% lower, respectively, than those treated with BL. In contrast, the Fe3+ in ferric chloride combines with As after hydrolysis and oxidation to form amorphous ferric arsenate precipitates or insoluble secondary minerals. Therefore, the curing effect of the modified biochar on As was more potent than that of applied biochar alone. In conclusion, ferric chloride-modified biochar can effectively inhibit the effects of water and fertilizer loss in farmland soil and realize cross-medium long-term inhibition and control of combined Cd and As pollution. [ABSTRACT FROM AUTHOR]

Mining and industrial operations are often associated with metalloid and heavy metal contamination of terrestrial and aquatic ecosystems. Heavy metals can weaken the soil's purification ability to remediate and can accumulate in the human body through crops grown in contaminated soil. In this study, a stabilization method was applied for the remediation of arsenic (As) and heavy metal (Pb and Zn) contaminated soil. Scallop shells (SLS) and starfish (Asterias amurensis, ASF), commonly regarded as waste resource materials, are selected as stabilizers. Proper recycling/reuse measures are required to limit uncontrolled disposal of SLS and ASF, prevent environmental degradation of coastal areas, and take advantage of their high calcium carbonate contents. The stabilizers were processed through −#10 mesh (0.2 mm) and −#20 mesh (0.85 mm) sieves. In addition, calcined stabilizers were produced by calcining SLS and ASF at 900 °C to compare stabilization efficiency based on the presence/absence of high-temperature heat treatment. Each of the three types of processed stabilizers was added to contaminated soil at 2 to 10 wt.%, and the mixtures were subjected to wet curing for 28 days. Extraction with 0.1 N HCl was applied for stabilization efficiency assessment. Crops were cultivated in the stabilized soil to evaluate As and heavy metal immobilization capacity. Analysis by X-ray diffraction (XRD) established that calcite (CaCO3) was observed in the natural materials and quicklime (CaO) in the calcined materials. The stabilization efficiency assessment results showed that treatment with SLS and ASF effectively reduced the elution of Pb and Zn. SLS was effective in immobilizing As, but the application of natural ASF increased the leachability of As due to the presence of organic matter. However, applying calcined ASF effectively immobilized As because the organic matter was removed at high temperatures. When the transition of As and heavy metals to crops was evaluated, Pb concentrations that exceeded the criterion for leafy vegetables were detected in the lettuce grown in contaminated soil. However, Pb was not detected in the lettuce grown in SLS- and ASF-treated soil, confirming the stability of heavy metal immobilization. Scanning electron microscopy–energy dispersive X-ray spectroscopy (SEM-EDX) analysis showed that the pozzolanic reaction is related to heavy metal immobilization, and Ca–As precipitation is related to the immobilization of As. The results of this study verified that SLS and ASF effectively immobilize As and heavy metals (Pb and Zn) around mines and that they can be used safely in agricultural soil. [ABSTRACT FROM AUTHOR]

Descriptor systems are more complex than normal systems, which are modeled by differential equations. This paper derives stability and stabilization criteria for uncertain fractional descriptor systems with neutral-type delay. Through the Lyapunov–Krasovskii functional approach, conditions subject to time-varying delay and parametric uncertainty are formulated as linear matrix inequalities. Based on the established criteria, static state- and output-feedback control laws are designed to ensure regularity and impulse-free properties, together with robust stability of the closed-loop system under permissible uncertainties. Numerical examples illustrate the effectiveness of the control methods and show that the results depend on the range of variation in the delays and on the fractional order, leading to stability analysis results that are less conservative than those reported in the literature. [ABSTRACT FROM AUTHOR]

A kind of reduced-dimension method based on a weighted explicit finite difference scheme and the proper orthogonal decomposition (POD) technique for diffusion equations with Riemann–Liouville fractional derivatives in space are discussed. The constructed approximation method written in matrix form can not only ensure a sufficient accuracy order but also reduce the degrees of freedom, decrease storage requirements, and accelerate the computation rate. Uniqueness, stabilization, and error estimation are demonstrated by matrix analysis. The procedural steps of the POD algorithm, which reduces dimensionality, are outlined. Numerical simulations to assess the viability and effectiveness of the reduced-dimension weighted explicit finite difference method are given. A comparison between the reduced-dimension method and the classical weighted explicit finite difference scheme is presented, including the error in the L 2 norm, the accuracy order, and the CPU time. [ABSTRACT FROM AUTHOR]

The dehydrocoupling reaction between alcohols and hydrosilanes is considered to be one of the most atom-economical ways to produce Si–O coupling compounds because its byproduct is only hydrogen (H2), which make it extremely environmentally friendly. In past decades, various kinds of homogeneous catalysts for the dehydrocoupling of alcohols and hydrosilanes, such as transition metal complexes, alkaline earth metals, alkali metals, and noble metal complexes, have been reported for their good activity and selectivity. Nevertheless, the practical applications of these catalysts still remain unsatisfactory, which is mainly restricted by environmental impact and non-reusability. A facile and recyclable heterogeneous catalyst, ultra-small Ag nanoparticles supported on porous carbon (Ag/C) for the etherification of silanes, has been developed. It has high catalytic activity for the Si–O coupling reaction, and the apparent activation energy of the reaction is about 30 kJ/mol. The ultra-small Ag nanoparticles dispersed in the catalyst through the carrier C have an enrichment effect on all reactants, which makes the reactants reach the adsorption saturation state on the surface of Ag nanoparticles, thus accelerating the coupling reaction process and verifying that the kinetics of the reaction of the catalyst indicate a zero-grade reaction. [ABSTRACT FROM AUTHOR]

The p53 family remains a captivating focus of an extensive number of current studies. Accumulating evidence indicates that p53 abnormalities rank among the most prevalent in cancer. Given the numerous existing studies, which mostly focus on the mutations, expression profiles, and functional perturbations exhibited by members of the p53 family across diverse malignancies, this review will concentrate more on less explored facets regarding p53 activation and stabilization by the nuclear pore complex (NPC) in cancer, drawing on several studies. p53 integrates a broad spectrum of signals and is subject to diverse regulatory mechanisms to enact the necessary cellular response. It is widely acknowledged that each stage of p53 regulation, from synthesis to degradation, significantly influences its functionality in executing specific tasks. Over recent decades, a large body of data has established that mechanisms of regulation, closely linked with protein activation and stabilization, involve intricate interactions with various cellular components. These often transcend canonical regulatory pathways. This new knowledge has expanded from the regulation of genes themselves to epigenomics and proteomics, whereby interaction partners increase in number and complexity compared with earlier paradigms. Specifically, studies have recently shown the involvement of the NPC protein in such complex interactions, underscoring the further complexity of p53 regulation. Furthermore, we also discuss therapeutic strategies based on recent developments in this field in combination with established targeted therapies. [ABSTRACT FROM AUTHOR]

This study focuses on the decentralized stabilization issue of high-order large-scale nonlinear systems with unknown disturbances. A novel decentralized semi-global finite-time control approach is suggested by constructing a Lyapunov function with both quadratic and higher-order components and employing the method of homogeneous domination. Based on the designed Lyapunov function, a state-feedback controller is constructed for the nominal system. Subsequently, the scaling gain is flexibly introduced to enable semi-globally finite-time stabilization of the nonlinear system. Besides, the approach is extended to the problem of decentralized tracking control of high-order large-scale nonlinear systems. Finally, numerical and practical examples validate the effectiveness of the presented control strategy. [ABSTRACT FROM AUTHOR]

Stabilization using industrial by-products is presently gaining importance in the construction sector for improving the geotechnical characteristics of soft soils. The optimum dosage of stabilisers has become of great interest to experimenters in terms of improved strength, time, and economy for construction projects. This work presents the utilization of biomedical waste ash for improving the strength of soft soil. In this paper, response surface methodology (RSM) was adopted to determine the optimum combination curing period (C) and biomedical waste ash (BA) quantity for attaining the maximum unconfined compressive strength (UCS) of soft soil and to reduce the number of trial tests required. The response factors C and BA were varied from 0 to 14 days and 4% to 20%, respectively, and the experiments were conducted according to the experimental plan provided by the RSM design. Based on a Face-centred Central Composite Design (FCCCD), a mathematical equation was created for the experimental results. Analysis of variance (ANOVA) was used to determine the generated model's significance, and the results indicated a statically significant model (p ≤ 0.05). The results revealed that the curing period imparts more influence towards strength improvement, and the optimum dosage was 19.912% BA, with curing of 14 days to yield a maximum UCS of 203.008 kPa. This optimization technique may be suggested to obtain a preliminary estimation of strength prior to stabilization. [ABSTRACT FROM AUTHOR]

Preserving microbial ecosystems obtained from traditional cheese-making processes is crucial to safeguarding the biodiversity of microbial cheese communities and thus ensuring that the high flavor quality of traditional cheeses is maintained. Few protocols have been proposed for the long-term storage of microbial consortia. This work aimed to develop preservation methods to stabilize the entire microbial community in smear-ripened cheese without multiplication or isolation. A simplified microbial community, capable of reproducing the metabolic pattern of cheese maturation, was used in three independent cheese productions. Cheese samples were taken before and after the ripening step, mixed with maltodextrin or saline solution, and subjected to different stabilization conditions including freezing and freeze-drying, followed by 1 month of storage. Microbial survival was quantified using the colony-forming unit assay. Differential scanning calorimetry was used to relate the physical events occurring within the samples to the microbial storage stability. Freezing at −80 °C resulted in the lowest loss of culturability (<0.8 log unit), followed by freezing at −20 °C and freeze-drying. The ripening bacteria appeared as the most sensitive microorganisms within the community. Moreover, a successful cheese production using the best-stabilized community showed the possibility of preserving and re-using an entire microbial community of interest. [ABSTRACT FROM AUTHOR]

This paper presents a novel robust output feedback control that simultaneously performs both stabilization and trajectory tracking for a class of underactuated nonholonomic systems despite model uncertainties, external disturbance, and the absence of velocity measurement. To solve this challenging problem, a generalized normal form has been successfully created by employing an input–output feedback linearization approach and a change in coordinates (diffeomorphism). This research mainly focuses on the stabilization problem of nonholonomic systems that can be transformed to a normal form and pose several challenges, including (i) a nontriangular normal form, (ii) the internal dynamics of the system are non-affine in control, and (iii) the zero dynamics of the system are not in minimum phase. The proposed scheme utilizes combined backstepping and sliding mode control (SMC) techniques. Furthermore, the full-order high gain observer (HGO) has been developed to estimate the derivative of output functions and internal dynamics. Then, full-order HGO and the backstepping SMC have been integrated to synthesize a robust output feedback controller. A differential-drive type (2,0) the wheeled mobile robot has been considered as an example to support the theoretical results. The simulation results demonstrate that the backstepping SMC exhibits robustness against bounded uncertainties. [ABSTRACT FROM AUTHOR]

In this paper, there are two aims: one is Schauder and Sobolev estimates for the one-dimensional heat equation; the other is the stabilization of differential equations by stochastic feedback control based on discrete-time state observations. The nonhomogeneous Poisson stochastic process is used to show how knowing Schauder and Sobolev estimates for the one-dimensional heat equation allows one to derive their multidimensional analogs. The properties of a jump process is used. The stabilization of differential equations by stochastic feedback control is based on discrete-time state observations. Firstly, the stability results of the auxiliary system is established. Secondly, by comparing it with the auxiliary system and using the continuity method, the stabilization of the original system is obtained. Both parts focus on the impact of probability theory. [ABSTRACT FROM AUTHOR]

This comprehensive literature review investigates the impact of stabilization and reinforcement techniques on the mechanical, hygrothermal properties, and durability of adobe and compressed earth blocks (CEBs). Recent advancements in understanding these properties have spurred a burgeoning body of research, prompting a meticulous analysis of 70 journal articles and conference proceedings. The selection criteria focused on key parameters including construction method (block type), incorporation of natural fibers or powders, partial or complete cement replacement, pressing techniques, and block preparation methods (adobe or CEB). The findings unearth several significant trends. Foremost, there is a prevailing interest in utilizing waste materials, such as plant matter, construction and demolition waste, and mining by-products, to fortify or stabilize earth blocks. Additionally, the incorporation of natural fibers manifests in a discernible reduction in crack size attributable to shrinkage, accompanied by enhancements in durability, mechanical strength, and thermal resistance. Moreover, this review underscores the imperative of methodological coherence among researchers to facilitate scalable and transposable results. Challenges emerge from the variability in base soil granulometry and disparate research standards, necessitating concerted efforts to harness findings effectively. Furthermore, this review illuminates a gap in complete lifecycle analyses of earthen structures, underscoring the critical necessity for further research to address this shortfall. It emphasizes the urgent need for deeper exploration of properties and sustainability indicators, recognizing the inherent potential and enduring relevance of earthen materials in fostering sustainable development. This synthesis significantly contributes to the advancement of knowledge in the field and underscores the continued importance of earth-based construction methodologies in contemporary sustainable practices. [ABSTRACT FROM AUTHOR]

Youth homelessness represents a persistent and significant challenge for service sectors with limited best practice guidance. Housing supports, in particular, are widely deployed, with the practice-oriented literature providing little detail regarding service design beyond broad domains such as employment support and life skills coaching. The present multiple case study investigation was designed to develop a preliminary understanding of the guiding principles that attend the development of interventions that support youth exiting homelessness in the Canadian context. These case studies were conducted with a diverse group of five organizations recognized as sector leaders, with findings considered in light of practice standards from the better-established adult housing literature. Key findings with respect to service models included the strategies used to provide flexible, culturally responsive, tailored services with an emphasis on specialist support. Implementation factors included the navigation of strategic partnerships, the use of data in capacity-building, and the benefits and drawbacks of larger, centralized service environments versus smaller, dispersed environments. Youth-specific considerations in housing stabilization models are highlighted. This work contributes to a growing body of literature that seeks to articulate best practices in the effort to address and prevent youth homelessness. [ABSTRACT FROM AUTHOR]

In the realm of conditionally automated driving, understanding the crucial transition phase after a takeover is paramount. This study delves into the concept of post-takeover stabilization by analyzing data recorded in two driving simulator experiments. By analyzing both driving and physiological signals, we investigate the time required for the driver to regain full control and adapt to the dynamic driving task following automation. Our findings show that the stabilization time varies between measured parameters. While the drivers achieved driving-related stabilization (winding, speed) in eight to ten seconds, physiological parameters (heart rate, phasic skin conductance) exhibited a prolonged response. By elucidating the temporal and cognitive dynamics underlying the stabilization process, our results pave the way for the development of more effective and user-friendly automated driving systems, ultimately enhancing safety and driving experience on the roads. [ABSTRACT FROM AUTHOR]

Due to volume change and low strength, fine-grained soils are problematic in construction. Stabilization with cement and sawdust ash (SDA) by-products can improve engineering properties. This study aimed to investigate the effectiveness of cement and sawdust ash (SDA) in stabilizing fine-grained soils for liner applications. Varying proportions of cement (0–9%) and SDA (0–10%) were added to soil samples (n = 24). Specimens were tested for unconfined compressive strength (UCS), hydraulic conductivity (HC), and volumetric shrinkage strain (VSS). Two-way ANOVA analyzed stabilization effects. Optimal stabilization occurred with 6% cement and 6% SDA, resulting in significant increases in UCS (51 to 375 kN/m2) and decreases in HC (1.7 × 10−8 to 4.7 × 10−10 m/s) and VSS (12.8 to 3.51%) compared to untreated soil. ANOVA indicated that both cement and SDA had statistically significant (p < 0.05) effects on improving all three engineering properties. The addition of 6% cement and 6% SDA significantly improved the expansive soil's strength, hydraulic conductivity, and volume change properties. ANOVA confirmed the quantitative improvements and the significance of both stabilizers. Stabilization using the by-product SDA has the potential to be a sustainable soil improvement method. [ABSTRACT FROM AUTHOR]

Freeze-thaw cycles significantly impact construction by altering soil properties and stability, which can lead to delays and increased costs. While soil-stabilizing additives are vital for addressing these issues, stabilized soils remain susceptible to volume changes and structural alterations, ultimately reducing their strength after repeated freeze-thaw cycles. This study aims to introduce a different approach by employing magnesium chloride (MgCl2) as an antifreeze and soil stabilizer additive to enhance the freeze-thaw resilience of clay soils. We investigated the efficiency of MgCl2 solutions at concentrations of 4%, 9%, and 14% on soil by conducting tests such as Atterberg limits, standard proctor compaction, unconfined compression, and freeze-thaw cycles under extreme cold conditions (−10 °C and −20 °C), alongside microstructural analysis with SEM, XRD, and FTIR. The results showed that MgCl2 reduces the soil's liquid limit and plasticity index while enhancing its compressive strength and durability. Specifically, soil treated with a 14% MgCl2 solution maintained its volume and strength at −20 °C, with similar positive outcomes observed for samples treated with 14% and 9% MgCl2 solutions at −10 °C. This underlines MgCl2's potential to enhance soil stability during initial stabilization and, most importantly, preserve it under cyclic freeze-thaw stresses, offering a solution to improve construction practices in cold environments. [ABSTRACT FROM AUTHOR]

The Industrial Metrology Business Unit of Nikon Corporation, on behalf of ScottishPower Renewables and Maritime Archaeology (MA), Southampton, UK, has employed X-ray CT (computed tomography) to visualise the internal structure of an anchor found in the North Sea. The non-destructive method of internal inspection and measurement has helped to determine approximately when it was made. The results indicate that the artefact, initially thought to be potentially Roman, is probably more recent, likely dating to between the late 16th and early 17th centuries CE. This paper presents the discovery, recovery, analysis and interpretation of a significant find from a UK offshore wind farm and underscores the valuable role that non-destructive X-ray CT played in the investigation. [ABSTRACT FROM AUTHOR]

In order to address the challenges of resource utilization posed by construction waste, the substitution of natural aggregate (NA) with public fill (PF) contents was investigated for load reclamation and road grassroots applications. A comprehensive assessment of road performance for the recycled mixture was conducted, focusing on parameters such as unconfined compressive strength, splitting strength, compressive resilience modulus, dry shrinkage, and frost resistance. Additionally, the impact of incorporating PF at various types and replacement ratios on the microstructure of cement-stabilized aggregate (CSA) was analyzed. The results indicated that the unconfined compressive strength of cement-stabilized recycled mixture with varying PF contents meets the base strength requirements for heavy, medium, and light traffic pavement on secondary and sub-secondary roads in China. Notably, the unconfined compressive strength and resilience modulus follow a similar pattern, reaching their peak at a 25% PF content. Microscopic examination reveals that an appropriate PF content leads to the predominant formation of C(N)-A-S-H, hydrotalcite, Ca(OH)2, and CaCO3 as paste reaction products. As the replacement of public fill increases from 0% to 25%, there is a gradual stacking of gel products, which enhances the compactness of the microstructure by cementing together unreacted particles. Consequently, this process reduces dry shrinkage strain and effectively mitigates the formation of reflection cracks. Applying large quantities of public fill to road construction can effectively deal with various waste accumulation problems and produce a novel road material with significant social, economic, and environmental benefits. [ABSTRACT FROM AUTHOR]

Cellulose nitrates (CNs)-blended composites based on celluloses of bacterial origin (bacterial cellulose (BC)) and plant origin (oat-hull cellulose (OHC)) were synthesized in this study for the first time. Novel CNs-blended composites made of bacterial and plant-based celluloses with different BC-to-OHC mass ratios of 70/30, 50/50, and 30/70 were developed and fully characterized, and two methods were employed to nitrate the initial BC and OHC, and the three cellulose blends: the first method involved the use of sulfuric–nitric mixed acids (MAs), while the second method utilized concentrated nitric acid in the presence of methylene chloride (NA + MC). The CNs obtained using these two nitration methods were found to differ between each other, most notably, in viscosity: the samples nitrated with NA + MC had an extremely high viscosity of 927 mPa·s through to the formation of an immobile transparent acetonogel. Irrespective of the nitration method, the CN from BC (CN BC) was found to exhibit a higher nitrogen content than the CN from OHC (CN OHC), 12.20–12.32% vs. 11.58–11.60%, respectively. For the starting BC itself, all the cellulose blends of the starting celluloses and their CNs were detected using the SEM technique to have a reticulate fiber nanostructure. The cellulose samples and their CNs were detected using the IR spectroscopy to have basic functional groups. TGA/DTA analyses of the starting cellulose samples and the CNs therefrom demonstrated that the synthesized CN samples were of high purity and had high specific heats of decomposition at 6.14–7.13 kJ/g, corroborating their energy density. The CN BC is an excellent component with in-demand energetic performance; in particular, it has a higher nitrogen content while having a stable nanostructure. The CN BC was discovered to have a positive impact on the stability, structure, and energetic characteristics of the composites. The presence of CN OHC can make CNs-blended composites cheaper. These new CNs-blended composites made of bacterial and plant celluloses are much-needed in advanced, high-performance energetic materials. [ABSTRACT FROM AUTHOR]

In this study, the effect of various immobilization methods on the biochemical properties of phospholipase C (PLC) from Bacillus cereus obtained from the oily soil located in Sfax, Tunisia, was described. Different supports were checked: octyl sepharose, glyoxyl agarose in the presence of N-acetyl cysteine, and Q-sepharose. In the immobilization by hydrophobic adsorption, a hyperactivation of the PLCBc was obtained with a fold of around 2 times. The recovery activity after immobilization on Q-sepharose and glyoxyl agarose in the presence of N-acetyl cysteine was 80% and 58%, respectively. Furthermore, the biochemical characterization showed an important improvement in the three immobilized enzymes. The performance of the various immobilized PLCBc was compared with the soluble enzyme. The derivatives acquired using Q-sepharose, octyl sepharose, and glyoxyl agarose were stable at 50 °C, 60 °C, and 70 °C. Nevertheless, the three derivatives were more stable in a large range of pH than the soluble enzyme. The three derivatives and the free enzyme were stable in 50% (v/v) ethanol, hexane, methanol, and acetone. The glyoxyl agarose derivative showed high long-term storage at 4 °C, with an activity of 60% after 19 days. These results suggest the sustainable biotechnological application of the developed immobilized enzyme. [ABSTRACT FROM AUTHOR]

The iron-modified coal gasification slag (Fe-CGS) material has excellent performance in purifying heavy-metal-contaminated water due to its good surface properties and adsorption capacities. However, it is unclear whether it can provide long-term simultaneous stabilization of Cd and As in composite-contaminated soils in extreme environments. This study investigated the long-term stabilization of Cd and As in acidic (JLG) and alkaline (QD) soils by simulating prolonged heavy rainfall with the addition of Fe-CGS. Multiple extraction methods were used to analyze the immobilization mechanisms of Cd and As in soil and their effects on bioavailability. The results indicate that the stabilization efficiency was related to the dosage of Fe-CGS. The concentrations of Cd and As in the JLG soil leachate were reduced by 77.6% (2.0 wt%) and 87.8% (1.0 wt%), respectively. Additionally, the availability of Cd and As decreased by 46.7% (2.0 wt%) and 53.0% (1.0 wt%), respectively. In the QD soil leachate, the concentration of Cd did not significantly change, while the concentration of As decreased by 92.3% (2.0 wt%). Furthermore, the availability of Cd and As decreased by 22.1% (2.0 wt%) and 40.2% (1.0 wt%), respectively. Continuous extraction revealed that Fe-CGS facilitated the conversion of unstable, acid-soluble Cd into oxidizable Cd and acid-soluble Cd. Additionally, it promoted the transformation of both non-specifically and specifically adsorbed As into amorphous iron oxide-bound and residual As. Fe-CGS effectively improved the soil pH, reduced the bioavailability of Cd and As, and blocked the migration of Cd and As under extreme rainfall leaching conditions. It also promoted the transformation of Cd and As into more stable forms, exhibiting satisfactory long-term stabilization performance for Cd and As. [ABSTRACT FROM AUTHOR]

Red mud (RM) is a waste material obtained during the production of aluminum from bauxite minerals. RM causes environmental pollution due to its high alkaline properties. Therefore, RM materials are stored in waste reservoirs. As production continues, the number of required waste reservoirs increases day by day. This study aims to utilize RM waste material in construction structures to contribute to the economy. The research investigates the potential use of RM waste material as road fill material. RM was improved using another waste material of fly ash (FA) since RM has low strength. Atterberg limit tests, compaction tests, unconfined compression tests, CBR tests, and SEM analyses were conducted on stabilized RM samples. In the physical properties of stabilized RM, Atterberg limits and optimum moisture content increase and density decreases since FA content increases. In the mechanical properties of stabilized RM, unconfined compressive strength, initial and secant modulus of elasticity, and California bearing ratio increase and maximum peak strain decreases since FA content and curing period increase. SEM images prove the increase in mechanical properties due to the cementation products (CSH and CAH gels) formed in the microstructure of stabilized RM. The results showed that RM waste stabilized with FA can be used as road subgrade material. [ABSTRACT FROM AUTHOR]

Craniocervical tumors lead to cervical pain, instability, and neurological symptoms, reducing the quality of life. Effective surgical intervention at the craniocervical junction (CCJ) is critical and complex, involving comprehensive approaches and advanced reconstructive techniques. This study, conducted at Mexico City's National Institute of Cancerology, focused on three surgical cases that occurred in 2023 involving tumors at the CCJ: two chordomas and one prostate adenocarcinoma. We utilized a specialized technique: clivus-cervical stabilization reinforced with a polymethylmethacrylate (PMMA)-filled cervical mesh. Postoperatively, patients showed marked neurological recovery and reduced cervical pain, with enhanced Karnofsky and Eastern Cooperative Oncology Group (ECOG) scores indicating improved life quality. The surgical technique provided excellent exposure and effective tumor resection, utilizing PMMA-filled cervical mesh for stability. Tumoral lesions at the CCJ causing instability can be surgically treated through a transoral approach. This type of approach should be performed with precise indications to avoid complications associated with the procedure. [ABSTRACT FROM AUTHOR]

Simple Summary: This study focused on the importance of accurately assessing ram sperm quality for optimizing assisted reproductive technologies in sheep. Semen preservation can lead to sperm damage due to various stressors, including osmotic, biochemical, and thermal factors. To address this issue, the research aimed to determine the best time to evaluate ram sperm quality and identify the factor causing changes in sperm quality during liquid storage. In Experiment 1, ejaculated sperm were assessed for motility and functionality at different preservation times: 0, 3, 6, and 24 h. Both motility and functionality improved after 6 h. Experiment 2 delved into the responsible factor by using epididymal sperm. Results revealed that extender addition to the sperm caused altered motility at 0 and 24 h, and reduced functionality at 0 h. This suggests that the extender initially alters ram sperm, leading to sublethal damage that becomes reversible after 3 to 6 h of semen preservation. Thus, ram sperm require an adaptation period of 3 to 6 h to the extender before a precise quality assessment. This finding has practical implications for reproduction centers, allowing better workflow organization and optimal expression of ram sperm attributes at the time of cervical artificial insemination. Accurate assessment of ram sperm quality is crucial to optimizing assisted reproductive technologies in sheep. However, semen preservation can induce sperm due to osmotic, biochemical, and thermal stress. Stabilizing sperm with a suitable cooling rate and adaptation period to the extender could mitigate these effects for a more reliable evaluation. This study aimed to determine: (1) the best time to assess ram sperm quality, and (2) the factor responsible for the altered state of ram sperm during the first hours of liquid storage. In Experiment 1, ejaculated sperm were diluted and assessed for sperm motility and functionality at four preservation times: 0, 3, 6, and 24 h as sperm damage control. Both sperm motility and functionality improved after 6 h. Experiment 2 investigated the factor responsible for sperm quality change by testing the interactions of seminal plasma and extender with sperm from epididymides independently and in combination. The evaluation of sperm was performed as in Experiment 1. Sperm in groups containing the extender showed altered motility at 0 and 24 h, and lower functionality at 0 h. Thus, we could assume that extender addition initially alters ram sperm, causing sublethal damage that is reversible after 3 to 6 h of semen preservation. In conclusion, ram sperm require an adaptation time of 3 to 6 h to the extender before an accurate quality assessment can be conducted. This has practical implications for reproduction centers, enabling better workflow organization and optimal expression of ram sperm attributes when cervical artificial insemination is routinely performed. [ABSTRACT FROM AUTHOR]

Background: Multi-comminuted, intra-articular fractures of the distal humerus still pose a challenge to modern orthopedics due to unsatisfactory treatment results and a high percentage (over 50%) of postoperative complications. When surgical treatment is chosen, such fractures are fixed using two plates with locking screws, which can be used in three spatial configurations: either parallel or one of two perpendicular variants (posterolateral and posteromedial). The evaluation of the fracture healing conditions for these plate configurations is unambiguous. The contradictions between the conclusions of biomechanical studies and clinical observations were the motivation to undertake a more in-depth biomechanical analysis aiming to indicate the weak points of two-plate fracture stabilization. Methods: Research was conducted using the finite element method based on an experimentally validated model. Three variants of distal humerus fracture (Y, λ, and H) were fixed using three different plate configurations (parallel, posterolateral, and posteromedial), and they were analyzed under six loading conditions, covering the whole range of flexion in the elbow joint (0–145°). A joint reaction force equal to 150 N was assumed, which corresponds with holding a weight of 1 kg in the hand. The biomechanical conditions of bone union were assessed based on the interfragmentary movement (IFM) and using criteria formulated by Steiner et al. Results: The IFMs were established for particular regions of all of the analyzed types of fracture, with distinction to the normal and tangential components. In general, the tangential component of IFM was greater than normal. A strong influence of the elbow joint's angular position on the IFM was observed, with excessive values occurring for flexion angles greater than 90°. In most cases, the smallest IFM values were obtained for the parallel plaiting, while the greatest values were obtained for the posteromedial plating. Based on IFM values, fracture healing conditions in particular cases (fracture type, plate configuration, loading condition, and fracture gap localization) were classified into one of four groups: optimal bone union (OPT), probable union (PU), probable non-union (PNU), and non-union (NU). Conclusions: No plating configuration is able to ensure distal humerus fracture union when the full elbow flexion is allowed while holding a weight of 1 kg in the hand. However, flexion in the range of 0–90° with such loadings is acceptable when using parallel plating, which is a positive finding in the context of the early rehabilitation process. In general, parallel plating ensures better conditions for fracture healing than perpendicular plate configurations, especially the posteromedial version. [ABSTRACT FROM AUTHOR]

This paper investigates the effect of subgrade soil stabilization on the performance and life extension of flexible pavements. Several variables affecting soil stabilization were considered, including subgrade soil type (CL or CH), additive type and content (3, 6, and 9% of hydrated lime, 5, 10, and 15% of class C fly ash (CFA), and 5, 10, and 15% of cement kiln dust (CKD)), three stabilization thicknesses (15, 30, and 45 cm), and four pavement sections with varying thicknesses. The effects of these variables were investigated using four different damage mechanisms, including the fatigue life of the asphalt concrete (AC) and stabilized subgrade layers, the crushing life of the stabilized subgrade soil, and the rutting life of the pavement, using a non-linear mechanistic-empirical methodology. The results suggest that the optimum percentage that maximizes the pavement life occurs at 3% of lime for subgrade soil type CL, 6% of lime for subgrade type CH, and 15% of CFA and CKD for both subgrade soil types. The maximum pavement life increase occurred in the section with the lowest thickness and the highest stabilization thickness, which was 1890% for 3% of lime in the CL subgrade and 568% for 6% of lime in the CH subgrade. The maximum increase in the pavement life of subgrade stabilization with 15% of CFA was 2048% in a CL subgrade, and 397% in a CH subgrade, and life extension due to subgrade stabilization with 15% of CKD was 2323% in a CL subgrade and 797% in a CH subgrade. [ABSTRACT FROM AUTHOR]

In this paper, two systematic control design strategies are proposed for strict-feedback nonholonomic systems with full-state constraints to solve stabilization and adaptive stabilization problems. The stabilization schemes involve the introduction of state scaling, the barrier Lyapunov function (BLF), the integrator backstepping method, and the tuning function approach. In addition, a discontinuous switching control strategy is proposed to achieve the control goal if the first system state's initial state is confined to zero. In both stabilization and adaptive stabilization control, the system states can be regulated at the origin, and meanwhile, the full-state constraints are realized. Finally, it is shown that the simulation results are consistent with the theory analysis results, which further demonstrates the effectiveness of the proposed control schemes. [ABSTRACT FROM AUTHOR]

Large areas of estuarine deposits exist on the coastal plains of the southeast Queensland coast with a countered depth of up to 30 m. These deposits are categorized as sediments that originated during the Holocene Age. The sediments have not been consolidated or subjected to considerable pressure since the end of the Ice Age. The structure of these deposits consists of large ratios of porosity, causing high soil compressibility, which lowers the bearing capacity of the soils. Therefore, the soils of the region cannot maintain sufficient support for construction loads, and consequent malfunctions could occur in short-term and long-term periods. The objective of this paper is to investigate the suitability of new soil stabilization additives in the southeast Queensland region and the optimum additive content of cementitious materials and an advanced mixing modifier branded as DuraCrete. A combination of Portland cement and DuraCrete was used as a soil additive. Three DuraCrete-to-cement ratios were used: 2%, 3%, and 4% by weight. Soil collected from the Port of Brisbane region was treated by adding the additives as a percentage of its weight; four percentages were considered: 10%, 20%, 25%, and 30% for each combination of additives. The performance of the treated soils was examined under unconfined compression after 28 days of curing. The results revealed that increases in the unconfined compressive strength were detected as DuraCrete was added to the mixtures. For 30% additives, increases of about 15%, 34%, and 17% were detected when DuraCrete was added as 2%, 3%, and 4%, respectively. The results also revealed that 3% DuraCrete content provided significant stabilization compared to 2% and 4% for 25% and 30% additive-treated soils; such behavior was also observed for the specimens of 25% content of additives. Additionally, DuraCrete can be considered a promising material that can be combined with cement to obtain the desired stabilization of soft soils. [ABSTRACT FROM AUTHOR]

Cobalt diphosphides (CoP2) show a high theoretical capacity and hold great promise as anode materials for lithium-ion batteries (LIBs). However, the large variation in the volume and structure of CoP2 caused during lithium-ion insertion and extraction results in electrode fragmentation and a compromised solid electrolyte interface, ultimately leading to poor cycling performance. Herein, a composite of CoP2 nanoparticles encapsulated in carbon matrix has been successfully synthesized by carbonization of Co-MOF-based zeolitic imidazolate frameworks (ZIF-67) and sequential phosphorization and further wrapped in graphene oxide (CoP2@C@GO). The formation of CoP2 was confirmed by X-ray diffraction, high-resolution transmission electron microscopy and X-ray photoelectron spectroscopy. The morphology of CoP2@C with and without GO wrapping was examined by scanning electron microscopy and transmission electron spectroscopy. It was demonstrated that the decoration of GO significantly reduces the polarization of CoP2@C electrodes, enhancing their charge capacity and cycling stability as an anode material for LIBs. After 200 cycles, they deliver a capacity of 450 mAh·g−1. [ABSTRACT FROM AUTHOR]

Sous-vide is a process comprising vacuum-sealing food, heating it to the desired temperature, and circulating it in a water bath in a sous vide machine. This cooking technique is increasingly common in homes and catering establishments due to its simplicity and affordability. However, manufacturers and chef's recommendations for low-temperature and long-term sous-vide cooking in media raise food safety concerns, particularly when preparing beef tenderloin. In this study, Salmonella enterica was found to be inactivated by heat and sage essential oil (EO) in beef samples from musculus psoas major that had been sous vide processed. To determine whether heat treatment was likely to increase the sous vide efficiency, S. enterica and sage EO were mixed. After being vacuum-packed and injected with S. enterica, the samples were cooked at 50–65 °C through the sous vide technique for the prescribed time. On days 1, 3, and 6, the amounts of S. enterica, total bacteria, and coliform bacteria were measured in the control and treated groups of beef processed sous vide. Mass spectrometry was used to identify bacterial isolates on different days. On each day that was measured, a higher number of all the microbiota was found in the samples exposed to 50 °C for 5 min. The most frequently isolated microorganisms from both groups of samples were Pseudomonas fragi (17%), Pseudomonas cedrina (8%), and Proteus vulgaris (8%); in the treated group, also S. enterica (21%), Pseudomonas fragi (13%), and Pseudomonas veronii (6%). After the heat treatment of samples at 65 °C for 20 min, the total count of bacteria and coliform bacteria was zero. It has been shown that adding sage essential oil (EO) in combination with sous vide processing technique leads to the stabilization and safety of beef tenderloin. [ABSTRACT FROM AUTHOR]

This paper investigates the stabilization of the generalized Lotka–Volterra (GLV) biological model, which is affected by the asymptotically unbounded external disturbances, and presents some new results. Firstly, two stabilizers are proposed for the nominal GLV system. Then, some appropriate filters are designed and applied to asymptotically track the corresponding disturbances. Based on these filters, two disturbance-estimator (DE)-based controllers are presented to cancel the corresponding disturbances. Compared to the existing results, the advantage of this paper is in handling the asymptotically unbounded external disturbances effectively. Finally, the correctness and effectiveness of the proposed results are verified by computer simulation. [ABSTRACT FROM AUTHOR]

Over the past decade, fractional-order laser chaotic systems have attracted a lot of attention from a variety of fields, including theoretical research as well as practical applications, which has resulted in the development of a number of different system classes. This paper introduces a novel single-input finite-time PID sliding mode control (SMC) technique to stabilize a specific group of unknown 4-dimensional chaotic fractional-order (FO) laser systems. By combining the PID concept with the FO-version of the Lyapunov stability theory, a novel finite-time PID SMC strategy has been developed, which effectively mitigates chaotic behavior in the mentioned unknown 4-dimensional chaotic FO laser system. This method makes use of a characteristic of FO chaotic systems known as boundedness, which is used here. Notably, the control input's sign function, which is responsible for undesirable chattering, is transformed into the fractional derivative of the control input. This transformation results in a smooth and chattering-free control input, further enhancing the method's performance. To demonstrate the efficacy of the proposed chattering-free–finite-time PID SMC technique, two numerical scenarios are presented, showcasing its efficient performance in stabilizing the unknown 4-dimensional chaotic FO laser system. These scenarios serve as illustrations of the method's potential for practical applications. [ABSTRACT FROM AUTHOR]

Paintings and other works of art created with fragile and mechanically unstable powdery media present challenges to conservators. Frequently, powdery media is water-sensitive, extremely fragile, tends to delaminate, and may be altered by even the slightest physical action or interaction with liquids. Materials that can provide an efficient stabilization without unacceptably altering the optical characteristics of the delicate substrate are extremely limited. Among these, Funori, Isinglass, and Methocel A4C have become established for this use. In bench practice, consolidants are frequently applied in a non-contact way, using ultrasonic and pneumatic aerosol generators to minimize the impact of the consolidant on sensitive substrates. However, nebulizing the available materials is problematic in bench practice, because of their high viscosity and, only extremely low concentrations can be nebulized using low kinetic impact ultrasonic or pressure-based misting systems adopted from the healthcare industry. As a potential innovative solution, this study introduces novel ultra-low viscosity (ULV) cellulose ethers (ULV-HPMC) for stabilisation of unstable porous and powdery surfaces, which have been successfully applied in bench practice for the pilot treatment of Edvard Munch painting on canvas and two 19th c. Thai gouache paintings on panel. Novel ULV-HPMC materials have multiple desirable qualities for consolidation treatments in conservation, and in accelerated aging tests marginally outperformed Methocel A4C, considered to be one of the most stable consolidants in the practice of conservation. Because of the ultra-low viscosity, higher concentrations of ULV-HPMC materials can be applied as water-based aerosols in a non-contact way and in fewer applications, which is a significant advantage in the treatment of delicate water-sensitive surfaces. Notably, novel ULV biopolymers are low-cost, derive from sustainable and renewable sources, and do not raise health and environmental concerns. Such novel materials and methods seamlessly resonate with the ICOM-CC's Melbourne 2014 declaration, EU Green Deal, and the UN's Sustainable Development goals and show potential adding new sustainable materials with the exceptionally low viscosity to the conservator's tool box. [ABSTRACT FROM AUTHOR]

The development of artificial intelligence systems assumes that a machine can independently generate an algorithm of actions or a control system to solve the tasks. To do this, the machine must have a formal description of the problem and possess computational methods for solving it. This article deals with the problem of optimal control, which is the main task in the development of control systems, insofar as all systems being developed must be optimal from the point of view of a certain criterion. However, there are certain difficulties in implementing the resulting optimal control modes. This paper considers an extended formulation of the optimal control problem, which implies the creation of such systems that would have the necessary properties for its practical implementation. To solve it, an adaptive synthesized optimal control approach based on the use of numerical methods of machine learning is proposed. Such control moves the control object, optimally changing the position of the stable equilibrium point in the presence of some initial position uncertainty. As a result, from all possible synthesized controls, one is chosen that is less sensitive to changes in the initial state. As an example, the optimal control problem of a quadcopter with complex phase constraints is considered. To solve this problem, according to the proposed approach, the control synthesis problem is firstly solved to obtain a stable equilibrium point in the state space using a machine learning method of symbolic regression. After that, optimal positions of the stable equilibrium point are searched using a particle swarm optimization algorithm using the source functional from the initial optimal control problem statement. It is shown that such an approach allows for generating the control system automatically by computer, basing this on the formal statement of the problem and then directly implementing it onboard as far as the stabilization system has already been introduced. [ABSTRACT FROM AUTHOR]

Polyacrylonitrile (PAN) fibers are widely used as precursors in the manufacture of high-conducting and mechanically resistant carbon fibers. The modulation of such fibers is carried out through electrospinning. In this work, we show the production and control of the morphology of nanometric-range PAN fibers for their potential use as precursors for high-electrical-conductivity carbon fibers. PAN samples dissolved in dimethylformamide (DMF) were prepared at 6, 10, and 12% w/w, at 15 and 25 kV. The impact of the rotation of the collector drum at 100, 300, and 500 RPM was also studied. It was found that the percentage of PAN in the solution proportionally affects the diameter of the fibers and that the preparation potential affects the morphology. The rotation speed, when increased, decreases the diameter, and it has a negative impact on the morphology. Fibers prepared with 6% w/w at 15 kV and 500 RPM show 90 nm diameters, the smallest diameter of all the samples. [ABSTRACT FROM AUTHOR]

This work presents the study of Eucalyptus globulus bark and sawdust direct liquefaction. Laboratory scale experiments were carried out to assess the impact of several variables on the reaction yield and the sugar content of the bio-oil. These variables were the biomass type and concentration, the solvent, and the reaction time. The results show that E. globulus sawdust presented the highest yields (>95%), but the highest sugar content after water extraction was obtained for E. globulus bark (~5.5% vs. 1.2% for sawdust). Simultaneously, industrial-scale tests were carried out at the ENERGREEN pilot plant using the same reaction variables, which resulted in reaction yields of nearly 100%. The reagents and raw materials used, as well as the products obtained (bio-oil, reaction condensates, polyols, and sugar phases) were characterized by elemental analysis, infrared spectroscopy, thermogravimetry, and high-performance liquid chromatography with mass spectrometry. The heating value of the bio-oils is higher than the original biomass (higher heating value of E. globulus sawdust bio-oil 29 MJ/kg vs. 19.5 MJ/kg of the original E. globulus sawdust). The analyses of the bio-oils allowed us to identify the presence of high-added-value compounds, such as levulinic acid and furfural. Finally, a study of the accelerated aging of liquefied biomass showed that the biofuel density increases from 1.35 to 1.44 kg/dm3 after 7 days of storage due to the occurrence of repolymerization reactions. [ABSTRACT FROM AUTHOR]

The unstable substances in steel slag are the main substances that affect its stability, which limits the large-scale resource utilization of steel slag. Most of the current methods for stabilizing electric arc furnace (EAF) slag are time-consuming and cannot be completely stabilized. In view of this, this study aimed to explore the feasibility of microbial-induced calcium carbonate precipitation (MICP) technology for stabilizing EAF reducing slag, and this was to be achieved by using the reaction between carbonate ions and free calcium oxide (f-CaO) in reducing slag to form a more stable calcium carbonate to achieve the purpose of stabilization. The test results showed that, when the EAF reducing slag aggregates (ERSAs) were immersed in a Sporosarcina pasteurii bacteria solution or water, the f-CaO contained in it would react such that stabilization was achieved. The titration test results showed that the f-CaO content of the ERSAs immersed in the bacterial solution and water decreased. The expansion test results of the ERSAs that were subjected to hydration showed that the seven-day expansion of ERSAs after biomineralization could meet the Taiwan regulation requirement of an expansion rate less than 0.5%. The thermogravimetric analysis showed that both the experimental group and the control group might contain calcium carbonate compounds. The results of the X-ray diffraction analysis showed that the CaCO3 content in the ERSAs that were immersed in the bacterial solution was significantly higher than those that were immersed in water. Moreover, the compressive strength test results of concrete prepared with ERSAs showed that the compressive strength of the control group concrete began to decline after 28 days. In contrast, the experimental group concrete had a good stabilization effect, and there was no decline in compressive strength until 180 days. At 240 days, the surface cracks of the experimental group were particularly small, while the surface of the control group showed obvious cracks. These results confirmed that a mineralization reaction with S. pasteurii bacteria could be used as a stabilization technology for ERSAs. [ABSTRACT FROM AUTHOR]

Definition: Interest in covalent organic frameworks as high-value materials has grown steadily since their development in the 2000s. However, the great advantage that allows us to obtain these crystalline materials—the reversibility of the bonds that form the network—supposes a drawback in terms of thermal and chemical stability. Among the different strategies employed for the stabilization of imine-based Covalent Organic Frameworks (COFs), cycloaddition and other related cyclization reactions are especially significant to obtain highly stable networks with extended π-delocalization and new functionalities, expanding even further the potential application of these materials. Therefore, this entry gathered the most recent research strategies for obtaining stable COFs by means of cyclization reactions, including the Povarov reaction and intramolecular oxidative cyclization reactions as well as some other recent innovative approaches. [ABSTRACT FROM AUTHOR]

Antioxidants (AOs) from natural resources are an attractive research area, as petroleum-based products can be replaced in polymer stabilization. Therefore, novel esters based on the p-hydroxycinnamic acids p-coumaric acid, ferulic acid and sinapic acid were synthesized and their structure properties relationships were investigated. The structures of the novel bio-based antioxidants were verified using NMR and Fourier-transform infrared (FTIR) spectrometry. The high thermal stability above 280 °C and, therefore, their suitability as potential plastic stabilizers were shown using thermal gravimetric analysis (TGA). The radical scavenging activity of the synthesized esters was evaluated by using the 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay. Stabilization performance was evaluated in polypropylene (PP) using extended extrusion experiments, oxidation induction time (OIT) measurements and accelerated heat aging. In particular, the sinapic acid derivative provides a processing stability of PP being superior to the commercial state-of-the-art stabilizer octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl)propionate. [ABSTRACT FROM AUTHOR]