Search

Catechol (CT) is a phenolic compound widely used in various industrial sectors, but it is toxic; thus, there is a need for methods that aim to identify and quantify the existence of residues of this material in the environment. In this study a disposable printed electrochemical sensor was developed as an effective alternative for determining CT in water samples. The electrode, called SPEC, was manufactured using the screen-printing method using polyethylene terephthalate (PET) as a support, in which a conductive ink based on carbonaceous materials was used to print the working and auxiliary electrodes and a silver/silver chloride of ink on the reference electrode. The optimal ratio for the conductive ink was 6.25% carbon black, 35.42% graphite, and 58.33% nail polish. The ink obtained was characterized by scanning electron microscopy (SEM). The assessment of the effect of pH on the redox process showed Nernstian behavior (0.057 V pH−1), indicating that the process involves the same number of protons and electrons. Under optimized conditions, with 0.2 mol L−1 acetate buffer at pH 5.0, and by square wave voltammetry, the sensor presented sensitivity values of 0.31 μA L μmol−1, a detection limit of 5.96 μmol L−1, and a quantification limit of 19.87 μmol L−1. The sensor was applied to determine CT in tap water samples, and the results showed recoveries between 97.95 and 100.17%.

This work developed a conductive ink composed of carbonaceous material for printing electrochemical sensors. The optimized ink comprises graphite, carbon black, and nail polish, respectively (35.3:11.7:53%), as well as acetone as a solvent. The proportion was optimized with consideration of the binder’s solubilization, the ink’s suitability for the screen-printing process, and lower electrical resistance. The materials used, and the resulting ink, were analyzed by way of Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), Raman spectroscopy, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The charge transfer resistance (Rct) obtained was 0.348 kΩ. The conductive ink was used to print an electrode on a PET substrate, and a flexible and disposable electrode was obtained. The electroactive area obtained was 13.7 cm2, which was calculated by the Randles-Sevcik equation. The applicability of the device was demonstrated with a redox probe, providing a sensitivity of 0.02 µ A L mmol−1. The conductive ink has adequate homogeneity for producing electrodes using the screen-printing technique, with a low estimated production cost of $ 0.09 mL−1.

This study explores the intricate interaction between the properties of textile substrates and screen-printing parameters in shaping fabric circuits using silver conductive ink. Via analyzing key variables such as fabric type, mesh density, and the number of overprinted layers, the research revealed how the porous structure, large surface area, and fiber morphology of textile substrates influence ink absorption, ultimately enhancing the electrical connectivity of the printed circuits. Notably, the hydrophilic cotton staple fibers fabric effectively absorbed the conductive ink into the fabric substrate, demonstrating superior electrical performance compared with the hydrophobic polyester filament fabric after three overprinting, unlike the results observed after a single print. As mesh density decreased and the number of prints increased, the electrical resistance of the circuit gradually reduced, but ink bleeding on the fabric surface became more pronounced. Cotton fabric, via absorbing the ink deeply, exhibited less surface bleeding, while polyester fabric showed more noticeable ink spreading. These findings provide valuable insights for improving screen printing technology for textile circuits and contribute to the development of advanced fabric circuits that enhance the functionality of smart wearable technology.

Flexible electronics have revolutionized the field by overcoming the rigid limitations of traditional devices, offering superior flexibility and adaptability. Conductive ink performance is crucial, directly impacting the stability of flexible electronics. While metal filler-based inks exhibit excellent conductivity, they often lack mechanical stability. To address this challenge, we present a novel conductive ink utilizing a ternary composite filler system: liquid metal and two micron-sized silver morphologies (particles and flakes). We systematically investigated the influence of filler type, mass ratio, and sintering process parameters on the composite ink’s conductivity and mechanical stability. Our results demonstrate that flexible wires fabricated with the liquid metal/micron silver particle/micron silver flake composite filler exhibit remarkable conductivity and exceptional bending stability. Interestingly, increasing the liquid metal content results in a trade-off, compromising conductivity while enhancing mechanical performance. After enduring 5000 bending cycles, the resistance change in wires formulated with a 4:1 mass ratio of micron silver particles to flakes is only half that of wires with a 1:1 ratio. This study further investigates the mechanism governing resistance variations during flexible wire bending. Additionally, we observed a positive correlation between sintering temperature and pressure with the conductivity of flexible wires. The significance of the sintering parameters on conductivity follows a descending order: sintering temperature, sintering pressure, and sintering time. Finally, we demonstrate the practical application of this technology by integrating the composite ink-based flexible wires with conductive polymer-based strain sensors. This combination successfully achieved the detection of human movements, including finger and wrist bending.

This text discusses the synthesis of copper nanoparticles via a liquid phase reduction method, using ascorbic acid as a reducing agent and CuSO4·5H2O as the copper source. The synthesized copper nanoparticles are small in size, uniformly distributed, are mostly between 100–200 nm with clear boundaries between particles, and exhibit excellent dispersibility, making them suitable for metal conductive inks. 1. The copper nanoparticles are analyzed for good antioxidation properties, because their surface is coated with PVP and ascorbic acid. This organic layer somewhat isolates the particle surface from contact with air, preventing oxidation, and accounts for about 9% of the total weight. 2. When the prepared copper nanoparticles are spread on a polyimide substrate and sintered at 250 °C for 120 min, the resistivity can be as low as 23.5 μΩ·cm, and at 350 °C for 30 min, the resistivity is only three times that of bulk copper. 3. The prepared conductive ink, printed on a polyimide substrate using a direct writing tool, shows good flexibility before and after sintering. After sintering at 300 °C for 30 min and connecting the pattern to a circuit with a diode lamp, the diode lamp is successfully lit. 4. This method produces copper nanoparticles with small size, good dispersion, and antioxidation capabilities, and the conductive ink prepared from them demonstrates good conductivity after sintering.

This study presents the functionalization of silk fabric with SWCNT ink. The first step was the formation of a polydopamine (PDA) thin coating on the silk fabric to allow for effective bonding of SWCNTs. PDA formation was carried out directly on the fabric by means of polymerization of dopamine in alkali conditions. The Silk/PDA fabric was functionalized with SWCNT ink of different SWCNT concentrations by using the dip-coating method. IR and Raman analyses show that the dominant β-sheet structure of silk fibroin after the functionalization process remains unchanged. The heat resistance is even slightly improved. The hydrophobic silk fabric becomes hydrophilic after functionalization due to the influence of PDA and the surfactant in SWCNT ink. The ink significantly changes the electrical properties of the silk fabric, from insulating to conductive. The volume resistance changes by nine orders of magnitude, from 2.4 × 1012 Ω to 2.3 × 103 Ω for 0.12 wt.% of SWCNTs. The surface resistance changes by seven orders of magnitude, from 2.1 × 1012 Ω to 2.4 × 105 Ω for 0.17 wt.% of SWCNTs. The volume and surface resistance thresholds are determined to be about 0.05 wt.% and 0.06 wt.%, respectively. The low value of the percolation threshold indicates efficient functionalization, with high-quality ink facilitating the formation of percolation paths through SWCNTs and the influence of the PDA linker.

Cracks have a primary effect on the failure of a structure. Therefore, the development of crack sensors with high accuracy and resolution and cracks detection method are important. In this study, the crack sensors were fabricated, and the crack locations were detected with the electrical signal of the crack sensor. First, a metal grid-type micro-crack sensor based on silver was fabricated. The sensor is made with electrohydrodynamics (EHD) inkjet printing technology, which is well known as the next generation of printed electronics technology. Optimal printing conditions were established through experiments, and a grid sensor was obtained. After that, single cracks and multiple cracks were simulated on the sensor, and electrical signals generated from the sensor were measured. The measured electrical signal tracked the location of the cracks in three steps: simple cross-calculation, interpolation, and modified P-SPICE. It was confirmed that cracks could be effectively found and displayed using the method presented in this paper.

Copper-based nanoinks are emerging as promising low-cost alternatives to widely used silver nanoinks in electronic printing. However, the spontaneous oxidation of copper under ambient conditions poses significant challenges to its broader application. To address this issue, this paper presents an economical, large-scale, and environmentally friendly method for fabricating Cu@Ag nanoparticles (Cu@Ag NPs). The as-prepared nanoparticles exhibit a narrow size distribution of approximately 100 nm and can withstand ambient exposure for at least 60 days without significant oxidation. The Cu@Ag-based ink, with a 60 wt% loading, was screen-printed onto a flexible polyimide substrate and subsequently heat-treated at 290 °C for 15 minutes under a nitrogen atmosphere. The sintered pattern displayed a low electrical resistivity of 25.5 μΩ·cm (approximately 15 times the resistivity of bulk copper) along with excellent reliability and mechanical fatigue strength. The innovative Cu@Ag NPs fabrication method holds considerable potential for advancing large-scale applications of copper-based inks in flexible electronics.

In this article, a facile way for the doping of graphene and graphene derivatives with silver nanoparticles at different Ag ratios is described. Ag nanoparticles were formed directly on the surface of two different graphene substrates dispersed in dimethylformamide by the reduction of Ag cations with NaBH4. A few layered graphene nanosheets (FLG) produced from graphite and reduced graphene oxide functionalized with amino arylsulfonates (f-rGO) were used as substrates. The final graphene/Ag nanoparticle hybrid in the form of solid, dense spots showed enhanced electrical conductivity, which can be attributed to the formation of conductive interconnections between the 2D nanosheets. Importantly, electrical conductivities of 20 and 167 103 S m−1 were measured for the hybrids of f-rGO and FLG, respectively, with the higher Ag percentage without an annealing process. A representative hybrid f-rGO with Ag nanoparticles was used for the development of a highly conductive water-based gravure ink with excellent printing properties.

In the last decades, the demand for electronics and, therefore, electronic waste, has increased. To reduce this electronic waste and the impact of this sector on the environment, it is necessary to develop biodegradable systems using naturally produced materials with low impact on the environment or systems that can degrade in a certain period. One way to manufacture these types of systems is by using printed electronics because the inks and the substrates used are sustainable. Printed electronics involve different methods of deposition, such as screen printing or inkjet printing. Depending on the method of deposition selected, the developed inks should have different properties, such as viscosity or solid content. To produce sustainable inks, it is necessary to ensure that most of the materials used in the formulation are biobased, biodegradable, or not considered critical raw materials. In this review, different inks for inkjet printing or screen printing that are considered sustainable, and the materials that can be used to formulate them, are collected. Printed electronics need inks with different functionalities, which can be mainly classified into three groups: conductive, dielectric, or piezoelectric inks. Materials need to be selected depending on the ink’s final purpose. For example, functional materials such as carbon or biobased silver should be used to secure the conductivity of an ink, a material with dielectric properties could be used to develop a dielectric ink, or materials that present piezoelectric properties could be mixed with different binders to develop a piezoelectric ink. A good combination of all the components selected must be achieved to ensure the proper features of each ink.

Herein, we report results of the studies relating to the development of an impedimetric, magnetic bead-assisted supersandwich DNA hybridization assay for ultrasensitive detection of Neisseria gonorrhoeae, the causative agent of a sexually transmitted infection (STI), gonorrhea. First, a conductive ink was formulated by homogenously dispersing carboxylated multiwalled carbon nanotubes (cMWCNTs) in a stable emulsion of terpineol and an aqueous suspension of carboxymethyl cellulose (CMC). The ink, labeled C5, was coated onto paper substrates to fabricate C5@paper conductive electrodes. Thereafter, a magnetic bead (MB)-assisted supersandwich DNA hybridization assay was optimized against the porA pseudogene of N. gonorrhoeae. For this purpose, a pair of specific 5′ aminated capture probes (SCP) and supersandwich detector probes (SDP) was designed, which allowed the enrichment of target gonorrheal DNA sequence from a milieu of substances. The SD probe was designed such that instead of 1:1 binding, it allowed the binding of more than one T strand, leading to a ‘ladder-like’ DNA supersandwich structure. The MB-assisted supersandwich assay was integrated into the C5@paper electrodes for electrochemical analysis. The C5@paper electrodes were found to be highly conductive by a four-probe conductivity method (maximum conductivity of 10.1 S·cm−1). Further, the biosensing assay displayed a wide linear range of 100 aM-100 nM (109 orders of magnitude) with an excellent sensitivity of 22.6 kΩ·(log[concentration])−1. The clinical applicability of the biosensing assay was assessed by detecting genomic DNA extracted from N. gonorrhoeae in the presence of DNA from different non-gonorrheal bacterial species. In conclusion, this study demonstrates a highly sensitive, cost-effective, and label-free paper-based device for STI diagnostics. The ink formulation prepared for the study was found to be highly thixotropic, which indicates that the paper electrodes can be screen-printed in a reproducible and scalable manner.

The large-scale manufacturing of flexible electronics is nowadays based on inkjet printing technology using specially formulated conductive inks, but achieving adequate wetting of different surfaces remains a challenge. In this work, the development of a silver nanoparticle-based functional ink for printing on flexible paper and plastic substrates is demonstrated. Amphiphilic silver nanoparticles with narrow particle size distribution and good dispersibility were prepared via a two-step wet chemical synthesis procedure. First, silver nanoparticles capped with poly(acrylic acid) were prepared, followed by an amidation reaction with 3-morpholynopropylamine (MPA) to increase their lipophilicity. Density functional theory (DFT) calculations were performed to study the interactions between the particles and the dispersion medium in detail. The amphiphilic nanoparticles were dispersed in solvents of different polarity and their physicochemical and rheological properties were determined. A stable ink containing 10 wt% amphiphilic silver nanoparticles was formulated and inkjet-printed on different surfaces, followed by intense pulsed light (IPL) sintering. Low sheet resistances of 3.85 Ω sq–1, 0.57 Ω sq–1 and 19.7 Ω sq–1 were obtained for the paper, coated poly(ethylene terephthalate) (PET) and uncoated polyimide (PI) flexible substrates, respectively. Application of the nanoparticle ink for printed electronics was demonstrated via a simple flexible LED circuit.

High specific surface is a significant characteristic in zinc coatings that can be highly applicable in batteries and catalysts. Conventional methods to create foams are not cost-efficient, nor could they make a high specific surface. Electroplating has been developed that can produce a very high specific surface foam. On the other hand, conductive ink can create an affordable conductive surface with a high specific surface, so the study on using conductive ink, which has a cost-efficient nature, was necessary to create a conductive surface. This work has investigated the effect of crucial parameters, such as graphite size, coating time and bath composition, on the current efficiency and SEM microstructure. As a result, a 3 µm graphite size was found to be appropriate. Coated zinc escalates linearly with current efficiency for up to 5 h, and then it decreases. Although the zinc concentration increases up to 0.12 mol/L in the electrolyte, making a slight increase in loading, the current efficiency was almost unchanged. However, if it increases more, the loading and current efficiency significantly rise so that the loading grows up to 16 times and the current density increases up to 86%. Additionally, the morphology changes from dendritic to compact plates, sphere and semi-sphere, subsequently.

With the growing number of flexible electronics applications, environmentally benign ways of mass-producing graphene electronics are sought. In this study, we present a scalable mechanochemical route for the exfoliation of graphite in a planetary ball mill with melamine to form melamine-intercalated graphene nanosheets (M-GNS). M-GNS morphology was evaluated, revealing small particles, down to 14 nm in diameter and 0.4 nm thick. The M-GNS were used as a functional material in the formulation of an inkjet-printable conductive ink, based on green solvents: water, ethanol, and ethylene glycol. The ink satisfied restrictions regarding stability and nanoparticle size; in addition, it was successfully inkjet printed on plastic sheets. Thermal and photonic post-print processing were evaluated as a means of reducing the electrical resistance of the printed features. Minimal sheet resistance values (5 kΩ/sq for 10 printed layers and 626 Ω/sq for 20 printed layers) were obtained on polyimide sheets, after thermal annealing for 1 h at 400 °C and a subsequent single intense pulsed light flash. Lastly, a proof-of-concept simple flexible printed circuit consisting of a battery-powered LED was realized. The demonstrated approach presents an environmentally friendly alternative to mass-producing graphene-based printed flexible electronics.

In the scientific industry, sustainable nanotechnology has attracted great attention and has been successful in facilitating solutions to challenges presented in various fields. For the present work, silver nanoparticles (AgNPs) were prepared using a chemical reduction synthesis method. Then, a low-temperature sintering process was deployed to obtain an Ag-conductive ink preparation which could be applied to a flexible substrate. The size and shape of the AgNPs were characterized by ultraviolet–visible spectrophotometry (UV-Vis) and transmission electron microscopy (TEM). The experiments indicated that the size and agglomeration of the AgNPs could be well controlled by varying the reaction time, reaction temperature, and pH value. The rate of nanoparticle generation was the highest when the reaction temperature was 100 °C within the 40 min reaction time, achieving the most satisfactorily dispersed nanoparticles and nanoballs with an average size of 60.25 nm at a pH value of 8. Moreover, the electrical resistivity of the obtained Ag-conductive ink is controllable, under the optimal sintering temperature and time (85 °C for 5 min), leading to an optimal electrical resistivity of 9.9 × 10−6 Ω cm. The results obtained in this study, considering AgNPs and Ag-conductive ink, may also be extended to other metals in future research.

In this study, we developed an effective and rapid process for nanoscale ink printing, direct laser interference ink printing (DLIIP), which involves the photothermal reaction of a copper-based metal–organic decomposition ink. A periodically lined copper pattern with a width of 500 nm was printed on a 240 μm-wide line at a fabrication speed of 17 mm/s under an ambient environment and without any pre- or post-processing steps. This pattern had a resistivity of 3.5 μΩ∙cm, and it was found to exhibit a low oxidation state that was twice as high as that of bulk copper. These results demonstrate the feasibility of DLIIP for nanoscale copper printing with fine electrical characteristics.

In this study, we report a novel way to produce carbon-based conductive inks for electronic and sensor technology applications. Carbonized lignin, obtained from the waste products of the Eucalyptus globulus tree paper industry, was used to produce a stable conductive ink. To this end, liquid-phase compositions were tested with different amounts of carbonized lignin powder to obtain an ink with optimal conductivity and rheological properties for different possible uses. The combination that showed the best properties, both regarding electrochemical properties and green compatibility of the materials employed, was cyclohexanone/cellulose acetate/carbonized lignin 5% (w/w), which was used to produce screen-printed electrodes. The electrodes were characterized from a structural and electrochemical point of view, resulting in an electrochemically active area of 0.1813 cm2, compared to the electrochemically active area of 0.1420 cm2 obtained by employing geometrically similar petroleum-based screen-printed electrodes and, finally, their performance was demonstrated for the quantification of uric acid, with a limit of detection of 0.3 μM, and their biocompatibility was assessed by testing it with the laccase enzyme and achieving a limit of detection of 2.01 μM for catechol as the substrate. The results suggest that the developed ink could be of great use in both sensor and electronic industries, reducing the overall ecological impact of traditionally used petroleum-based inks.

The inkjet printing process is a promising electronic printing technique for large-scale, printed, flexible and stretchable electronics because of features such as its high manufacturing speed, environmental friendliness, simple process, low cost, accurate positioning, and so on. As the base material of printed conductive patterns, conductive ink is the foundation of the development of printed electronics technology, and directly affects the performance and the quality of electronic products. In this paper, conductive ink with silver nanowires (AgNWs) was prepared, with AgNWs of lengths of 2–5 µm and diameters of 20 nm or so, isopropyl alcohol and ethylene glycol as the mixed solvents, and modified polysilane as the wetting agent. We discussed the relationship between the formula of the AgNWs ink and the surface tension, viscosity, contact angle between ink droplet and poly(ethylene) terephthalate (PET) surface, as well as the film-forming properties of the ink. Further, we analyzed the effects of the number of printed layers and the ink concentration of the AgNWs on the microstructures, photoelectric properties and accuracy of the printed patterns, as well as the change in the sheet resistance of the film during different bending cycles. The experimental results show that flexible transparent conductive patterns with a light transmittance of 550 nm of 83.1–88.4% and a sheet resistance of 34.0 Ω∙sq−1–78.3 nm∙sq−1 can be obtained by using AgNWs ink of 0.38 mg∙mL−1 to 0.57 mg∙mL−1, a poly (ethylene terephthalate) (PET) substrate temperature of 40 °C, a nozzle temperature of 35 °C, and heat treated at 60 °C for 10 min. These performances indicate the excellent potential of the inkjet printing of AgNWs networks for developing flexible transparent conductive film.

The ability to fabricate functional 3D conductive elements via additive manufacturing has opened up a unique sector of ‘hybridized printed electronics’. In doing so, many of the rigid standards (i.e., planar circuit boards, potting, etc.,) of traditional electronics are abandoned. However, one critical challenge lies in producing robust and reliable interconnections between conductive inks and traditional hardware, especially when subjected to harsh environments. This research examines select material pairings for the most resilient interconnection. The method of test is wire bond pull testing that would represent a continuous strain on a connection and high acceleration testing of up to 50,000 g that would represent a sudden shock that electronics may experience in a drop or crash. Although these two environments may be similar to an overall energy exerted on the connection, the rate of force exerted may lead to different solutions. The results of this research provide insight into material selection for printed electronic interconnections and a framework for interconnection resiliency assessment, which is a critical aspect in realizing the production of next generation electronics technologies for the most demanding environments.

Presented here is a scalable and aqueous phase exfoliation of graphite to high yield and quality of few layer graphene (FLG) using Bovine Serum Albomine (BSA) and wet ball milling. The produced graphene ink is tailored for printable and flexible electronics, having shown promising results in terms of electrical conductivity and temporal stability. Shear force generated by steel balls which resulted in 2−3 layer defect-free graphene platelets with an average size of hundreds of nm, and with a concentration of about 5.1 mg/mL characterized by Raman spectroscopy, atomic force microscopy (AFM), transmittance electron microscopy (TEM) and UV-vis spectroscopy. Further, a conductive ink was prepared and printed on flexible substrate (Polyimide) with controlled resolution. Scanning electron microscopy (SEM) and Profilometry revealed the effect of thermal annealing on the prints to concede consistent morphological characteristics. The resulted sheet resistance was measured to be R s = 36.75 Ω / sqr for prints as long as 100 mm. Printable inks were produced in volumes ranging from 20 mL to 1 L, with potential to facilitate large scale production of graphene for applications in biosensors, as well as flexible and printable electronics.

The Holter monitor is used to measure an electrocardiogram (ECG) signal while a subject moves. However, the Holter monitor is uncomfortable for the subject. Another method of measuring the ECG signal uses a smart shirt. We developed a smart shirt that has six electrodes on the chest and can measure a detailed ECG, obtained with unipolar precordial leads. The electrodes and wires of the shirt are made of conductive ink that is flexible and stretchable. The smart shirt is stretchable and fits the body well. However, because of the gap between the smart shirt and the body, electrodes V1 and V2 do not touch the body consistently. We developed a conductive foam block that fills this gap. We investigated the characteristics of the conductive foam block, and measured ECG signals using the smart shirt. The electrical resistance of the conductive foam block was reduced by pressure. This characteristic could be utilized to measure the ECG signal because the block was pressed by the body and smart shirt. We could measure the ECG signal using the smart shirt and blocks while the subject walked and could detect peaks of the ECG signal while the subject jogged slowly.

Conductive inks are key enablers for the use of printing techniques in the fabrication of electronic systems. Focus on the understanding of aspects controlling the electrical performance of conductive ink is paramount. A comparison was made between microparticle Ag inks and an Ag nanoparticle ink. The microstructures resulting from thermal cure processes were characterized morphologically and also in terms of their effect on the resistivity of printed traces. For microparticle inks, the variability of resistivity measurements between samples as defined by coefficient of variation (CV) was greater than 0.1 when the resistivity was 10 to 50 times that of bulk Ag. When the resistivity was lower (~1.4 times that of bulk Ag) the CV of sample sets was less than 0.1. In the case of the nanoparticle ink, resistivity was found to decrease by a factor ranging from 1.2 to 1.5 after doubling the amount of layers printed prior to curing though it was expected to remain the same. Increasing the amount of layers printed also enhanced the sintering process.

The large-scale manufacturing of flexible electronics is nowadays based on inkjet printing technology using specially formulated conductive inks, but achieving adequate wetting of different surfaces remains a challenge. In this work, the development of a silver nanoparticle-based functional ink for printing on flexible paper and plastic substrates is demonstrated. Amphiphilic silver nanoparticles with narrow particle size distribution and good dispersibility were prepared via a two-step wet chemical synthesis procedure. First, silver nanoparticles capped with poly(acrylic acid) were prepared, followed by an amidation reaction with 3-morpholynopropylamine (MPA) to increase their lipophilicity. Density functional theory (DFT) calculations were performed to study the interactions between the particles and the dispersion medium in detail. The amphiphilic nanoparticles were dispersed in solvents of different polarity and their physicochemical and rheological properties were determined. A stable ink containing 10 wt% amphiphilic silver nanoparticles was formulated and inkjet-printed on different surfaces, followed by intense pulsed light (IPL) sintering. Low sheet resistances of 3.85 Ω sq -1 , 0.57 Ω sq -1 and 19.7 Ω sq -1 were obtained for the paper, coated poly(ethylene terephthalate) (PET) and uncoated polyimide (PI) flexible substrates, respectively. Application of the nanoparticle ink for printed electronics was demonstrated via a simple flexible LED circuit.

With the growing number of flexible electronics applications, environmentally benign ways of mass-producing graphene electronics are sought. In this study, we present a scalable mechanochemical route for the exfoliation of graphite in a planetary ball mill with melamine to form melamine-intercalated graphene nanosheets (M-GNS). M-GNS morphology was evaluated, revealing small particles, down to 14 nm in diameter and 0.4 nm thick. The M-GNS were used as a functional material in the formulation of an inkjet-printable conductive ink, based on green solvents: water, ethanol, and ethylene glycol. The ink satisfied restrictions regarding stability and nanoparticle size; in addition, it was successfully inkjet printed on plastic sheets. Thermal and photonic post-print processing were evaluated as a means of reducing the electrical resistance of the printed features. Minimal sheet resistance values (5 kΩ/sq for 10 printed layers and 626 Ω/sq for 20 printed layers) were obtained on polyimide sheets, after thermal annealing for 1 h at 400 °C and a subsequent single intense pulsed light flash. Lastly, a proof-of-concept simple flexible printed circuit consisting of a battery-powered LED was realized. The demonstrated approach presents an environmentally friendly alternative to mass-producing graphene-based printed flexible electronics.

In this study, we developed an effective and rapid process for nanoscale ink printing, direct laser interference ink printing (DLIIP), which involves the photothermal reaction of a copper-based metal-organic decomposition ink. A periodically lined copper pattern with a width of 500 nm was printed on a 240 μm-wide line at a fabrication speed of 17 mm/s under an ambient environment and without any pre- or post-processing steps. This pattern had a resistivity of 3.5 μΩ∙cm, and it was found to exhibit a low oxidation state that was twice as high as that of bulk copper. These results demonstrate the feasibility of DLIIP for nanoscale copper printing with fine electrical characteristics.

In the scientific industry, sustainable nanotechnology has attracted great attention and has been successful in facilitating solutions to challenges presented in various fields. For the present work, silver nanoparticles (AgNPs) were prepared using a chemical reduction synthesis method. Then, a low-temperature sintering process was deployed to obtain an Ag-conductive ink preparation which could be applied to a flexible substrate. The size and shape of the AgNPs were characterized by ultraviolet-visible spectrophotometry (UV-Vis) and transmission electron microscopy (TEM). The experiments indicated that the size and agglomeration of the AgNPs could be well controlled by varying the reaction time, reaction temperature, and pH value. The rate of nanoparticle generation was the highest when the reaction temperature was 100 °C within the 40 min reaction time, achieving the most satisfactorily dispersed nanoparticles and nanoballs with an average size of 60.25 nm at a pH value of 8. Moreover, the electrical resistivity of the obtained Ag-conductive ink is controllable, under the optimal sintering temperature and time (85 °C for 5 min), leading to an optimal electrical resistivity of 9.9 × 10 -6 Ω cm. The results obtained in this study, considering AgNPs and Ag-conductive ink, may also be extended to other metals in future research.

In this study, we report a novel way to produce carbon-based conductive inks for electronic and sensor technology applications. Carbonized lignin, obtained from the waste products of the Eucalyptus globulus tree paper industry, was used to produce a stable conductive ink. To this end, liquid-phase compositions were tested with different amounts of carbonized lignin powder to obtain an ink with optimal conductivity and rheological properties for different possible uses. The combination that showed the best properties, both regarding electrochemical properties and green compatibility of the materials employed, was cyclohexanone/cellulose acetate/carbonized lignin 5% ( w/w ), which was used to produce screen-printed electrodes. The electrodes were characterized from a structural and electrochemical point of view, resulting in an electrochemically active area of 0.1813 cm 2 , compared to the electrochemically active area of 0.1420 cm 2 obtained by employing geometrically similar petroleum-based screen-printed electrodes and, finally, their performance was demonstrated for the quantification of uric acid, with a limit of detection of 0.3 μM, and their biocompatibility was assessed by testing it with the laccase enzyme and achieving a limit of detection of 2.01 μM for catechol as the substrate. The results suggest that the developed ink could be of great use in both sensor and electronic industries, reducing the overall ecological impact of traditionally used petroleum-based inks.

The inkjet printing process is a promising electronic printing technique for large-scale, printed, flexible and stretchable electronics because of features such as its high manufacturing speed, environmental friendliness, simple process, low cost, accurate positioning, and so on. As the base material of printed conductive patterns, conductive ink is the foundation of the development of printed electronics technology, and directly affects the performance and the quality of electronic products. In this paper, conductive ink with silver nanowires (AgNWs) was prepared, with AgNWs of lengths of 2-5 µm and diameters of 20 nm or so, isopropyl alcohol and ethylene glycol as the mixed solvents, and modified polysilane as the wetting agent. We discussed the relationship between the formula of the AgNWs ink and the surface tension, viscosity, contact angle between ink droplet and poly(ethylene) terephthalate (PET) surface, as well as the film-forming properties of the ink. Further, we analyzed the effects of the number of printed layers and the ink concentration of the AgNWs on the microstructures, photoelectric properties and accuracy of the printed patterns, as well as the change in the sheet resistance of the film during different bending cycles. The experimental results show that flexible transparent conductive patterns with a light transmittance of 550 nm of 83.1-88.4% and a sheet resistance of 34.0 Ω∙sq -1 -78.3 nm∙sq -1 can be obtained by using AgNWs ink of 0.38 mg∙mL -1 to 0.57 mg∙mL -1 , a poly (ethylene terephthalate) (PET) substrate temperature of 40 °C, a nozzle temperature of 35 °C, and heat treated at 60 °C for 10 min. These performances indicate the excellent potential of the inkjet printing of AgNWs networks for developing flexible transparent conductive film.