Search

Although sandy islands in arid environments are vital protection sites for endemic species, they face constant natural and anthropogenic hazards, such as storm surge impacts and the occasional presence of off-road vehicles. Monitoring the sedimentary dune-beach displacement and balance is essential because sediment transportation usually does not depend on external sources, such as rivers. The latest generation of geomatic applications may be relevant to understanding coastal vulnerability due to their ability to acquire and process spatial data at unprecedented scales. The objective of this study was to analyze the sedimentary dynamics of a distinctive dune corridor on Altamura Island in the Gulf of California, Mexico. We compared three ultra-high spatial resolution digital surface models (DSMs) with geomorphic change detection (DoD), covering the 1150 m coastal stretch. We used light detection and ranging (LiDAR) data and analyzed changes in the coastline with the semi-automatic CoastSat tool. Although the orthomosaics and the DSM collected in April, June, and October 2021 show different conditions in sediment distribution along the beach-dune interface, depending on the direction and intensity of the wind, the two DoDs showed a constant sediment distribution balance of ~13 M m3 between April and June and June and October. LiDAR data along the 40-km length of the sandy island indicate that the entire island could present a similar sedimentation pattern between the dune and beach interface. The CoastSat data indicate a constant accretion of 125 m in the beach-ocean interface between 2015 and 2022. This study demonstrates that the sediment balance between the dune and the beach on arid sandy islands is vital for conserving their shoreline and all associated coastal ecosystems.

Since the end of the Little Ice Age (LIA, ~1830), the accelerated glaciers’ shrinkage along mid-latitude high mountain areas promoted a quick readjustment of geomorphological processes with the onset of the paraglacial dynamic, making proglacial areas among the most sensitive Earth’s landscapes to ongoing climate change. A potentially useful remote-sensing method for investigating such dynamic areas is the DEM (Digital Elevation Model) of Difference (DoD) technique, which quantifies volumetric changes in a territory between successive topographic surveys. After a detailed geomorphological analysis and comparison with historical maps of the Martello Valley (central Italian Alps), we applied the DoD for reconstructing post-LIA deglaciation dynamics and reported on the surface effects of freshly-onset paraglacial processes. The head of the valley is still glacierized, with three main ice bodies resulting from the huge reduction of a single glacier present at the apogee of the LIA. Aftermath: the glaciers lose 60% of their initial surface area, largely modifying local landforms and expanding the surface of the proglacial areas. The DoD analysis of the 2006–2015 timeframe (based on registered DEM derived from LiDAR—Light Detection and Ranging—data) highlights deep surface elevation changes ranging from +38 ± 4.01 m along the foot of rock walls, where gravitative processes increased their intensity, to −47 ± 4.01 m where the melting of buried ice caused collapses of the proglacial surface. This approach permits estimating the volume of sediments mobilized and reworked by paraglacial processes. Here, in less than 10 years, −23,675 ± 1165 m3 of sediment were removed along the proglacial area and transported down valley, highlighting the dynamicity of proglacial areas.

The Open-Source Digital Elevation Model (DEM) is fundamental data of the geoscientific community. However, the variation of its accuracy with land cover type and topography has not been thoroughly studied. This study evaluates the accuracy of five globally covered and open-accessed DEM products (TanDEM-X90 m, SRTEM, NASADEM, ASTER GDEM, and AW3D30) in the mountain area using ICESat/GLAS data as the GCPs. The robust evaluation indicators were utilized to compare the five DEMs’ accuracy and explore the relationship between these errors and slope, aspect, landcover types, and vegetation coverage, thereby revealing the consistency differences in DEM quality under different geographical feature conditions. The Taguchi method is introduced to quantify the impact of these surface characteristics on DEM errors. The results show that the slope is the main factor affecting the accuracy of DEM products, accounting for about 90%, 81%, 85%, 83%, and 65% for TanDEM-X90, SRTM, NASADEM, ASTER GDEM, and AW3D30, respectively. TanDEM-X90 has the highest accuracy in very flat areas (slope < 2°), NASADEM and SRTM have the greatest accuracy in flat areas (2 ≤ slope < 5°), while AW3D30 accuracy is the best in other cases and shows the best consistency on slopes. This study makes a new attempt to quantify the factors affecting the accuracy of DEM, and the results can guide the selection of open-source DEMs in related geoscience research.

South Manitou Island, part of Sleeping Bear Dunes National Lakeshore in northern Lake Michigan, is a post-glacial lacustrine landscape with substantial geomorphic changes including landslides, shoreline and bluff retreat, and sand dune movement. These changes involve interrelated processes, and are influenced to different extents by lake level, climate change, and land use patterns, among other factors. The utility of DEM of Difference (DoD) and other terrain analyses were investigated as a means of understanding interrelated geomorphologic changes and processes across multiple decades and at multiple scales. A 1m DEM was developed from 1955 historical aerial imagery using Structure from Motion Multi-View Stereo (SfM-MVS) and compared to a 2016 lidar-based DEM to quantify change. Landslides, shoreline erosion, bluff retreat, and sand dune movement were investigated throughout South Manitou Island. While the DoD indicates net loss or gain, interpretation of change must take into consideration the SfM-MVS source of the historical DEM. In the case of landslides, where additional understanding may be gleaned through review of the timing of lake high- and lowstands together with DoD values. Landscape-scale findings quantified cumulative feedbacks between interrelated processes. These findings could be upscaled to assess changes across the entire park, informing future change investigations and land management decisions.

High resolution terrestrial laser scanning data (TLS; terrestrial LiDAR) provide an excellent background for quantitative resource estimation through the comparative analysis of topographic surface changes. However, unlike airborne LiDAR data, which is usually provided as classified and contains a class of ground points, raw TLS data include all of the points of the scanned space within the specified scanner range. In effect, utilizing the latter data to estimate the volume of the resource by the differential analysis of digital elevation models (DEMs) requires the data to be specially prepared, i.e., separating from the point cloud only the data that represent the relevant class. In the case of natural resources, e.g., mineral resources, the class is represented by ground points. This paper presents the results that were obtained by differential analysis of high resolution DEMs (DEM of difference (DoD) method) using TLS data that were processed both manually (operator noise removal) and with the use of the automatic Cloth Simulation Filter (CSF) algorithm. Three different time pairs of DoD data were analyzed for a potential gravel-cobble deposit area of 45,444 m2, which was located at the bottom of the mouth section of the Scott River in south-east Svalbard. It was found that the applied method of ground point classification had very little influence on the errors in the range of estimating volumetric parameters of the mineral resources and measurement uncertainty. Moreover, it was shown that the point cloud density had an influence on the CSF filtering efficiency and spatial distribution of errors.

Mining typically involves extensive areas where environmental monitoring is spatially sporadic. New remote sensing techniques and platforms such as Structure from Motion (SfM) and unmanned aerial vehicles (UAVs) may offer one solution for more comprehensive and spatially continuous measurements. We conducted UAV campaigns in three consecutive summers (2015–2017) at a sub-Arctic mining site where production was temporarily suspended. The aim was to monitor a 0.5 km2 tailings impoundment and measure potential subsidence of tailings. SfM photogrammetry was used to produce yearly topographical models of the tailings surface, which allowed the amount of surface displacement between years to be tracked. Ground checkpoints surveyed in stable areas of the impoundment were utilized in assessing the vertical accuracy of the models. Observed surface displacements were linked to a combination of erosion, tailings settlement, and possible compaction of the peat layer underlying the tailings. The accuracy obtained indicated that UAV-assisted monitoring of tailings impoundments is sufficiently accurate for supporting impoundment management operations and for tracking surface displacements in the decimeter range.