Search

A novel wavelength triplexer based on Channel-Shaped Multimode Interference (C-MMI) structures on the InP platform is proposed for multi-channel integration compatibility in a 50G passive optical network (PON) system. Performance analysis of the proposed device is carried out by using the 3D Beam Propagation Method (3D-BPM), which shows excellent properties with insertion loss < 0.5 dB and low crosstalk < −14 dB for the 1342 nm in the Original band (1260–1360 nm), 1490 nm in the Short wavelength band (1460–1530 nm), and 1577 nm in the Long wavelength band (1565–1625 nm), also known as the OSL wavelengths band. Furthermore, the passbands of the three downlink channels of 1342 nm, 1490 nm, and 1577 nm, reach 14 nm, 20 nm, and 64 nm, respectively, which is wide enough to meet the 50G PON optical line terminal (OLT) requirement. Additionally, the proposed device is extremely compact with a total length of only 448 μm, making it attractive in the monolithic integrated laser chip and OLT packaged module.

A differential multi-frequency laser Doppler velocimetry is demonstrated, utilizing the synchronized multimode of a mode-locked distributed Bragg reflector laser. This scheme enables the simultaneous detection of multiple Doppler frequency shifts. Multiple differential Doppler shifts of 0.6 Hz, 1.3 Hz, and 1.9 Hz are obtained, with an average speed of 3.677 mm/s and a standard deviation of 0.122 mm/s, demonstrating a cross-referenced velocity measurement capability. The measurement results are also compared with the dual-frequency laser Doppler velocimetry scheme using electro-optical modulation.

The optical feedback tolerance (OFT) of a distributed Bragg reflector (DBR) laser was investigated experimentally. The static and modulation performance of the DBR laser under optical feedback was examined by evaluating its relative intensity noise (RIN) and bit error rate (BER). It is shown that the OFT of the DBR laser is closely related to its peak wavelength detuning relative to the Bragg wavelength. A high tolerance to optical feedback was demonstrated, both in the continuous wave (CW) and the direct modulation (DM) states, when the DBR laser was red-detuned relative to the Bragg wavelength. The excess RIN induced by optical feedback was well suppressed to a level of −140 dB/Hz at a feedback level of −9 dB in the CW state. In a 10 Gbps direct modulation state, bit error rates (BER) below 1 × 10−9 and 3 × 10−7 were obtained under a feedback level of −15 dB and −9 dB, respectively, for the case of back-to-back transmission. After 20 km fiber transmission, the BER still maintained below 1 × 10−7 under a feedback level of −15 dB, with a power penalty of less than 1 dB.

We report an electro-absorption modulator integrated with a distributed feedback Bragg laser fabricated by butt-joint technology. The lasing wavelength of the EML laser was 1311.71 nm, the output power was 10.04 mW when the current of the DFB section was 100 mA, the side-mode suppression ratio was greater than 50 dB, and the small-signal bandwidth was 29.40 GHz when the bias voltage of the modulator was −2 V. A 50 Gb/s data transmission over a single-mode fiber of up to 10 km was realized, which could be used as a light source for 50 G passive optical network systems.

With the deployment of the fifth generation of mobile networks (5G), 25 and 100 Gb/s directly modulated lasers and modules will become the mainstream optical transmitters. A directly modulated InGaAlAs/InP distributed Bragg reflector (DBR) laser is fabricated by butt-joint technology. A 25 Gb/s data transmission over a single-mode fiber of up to 10 km is demonstrated, and a wavelength tuning range of 14.28 nm is achieved through injection current tuning of a DBR section and temperature control of a thermoelectric cooler (TEC), which is the best candidate of colorless light sources for wavelength-division-multiplexed passive optical network (WDM-PON) systems.