Search

This study proposes the use of light detection and ranging (LiDAR) remote sensing (RS) to support morphometric research for estimating the aerodynamic roughness length (z0 ) of building placement on various scales. A LiDAR three-dimensional point cloud (3DPC) data processing graphical user interface (GUI) was developed to explore the z0 and related urban canopy parameters (UCPs) in the Incheon metropolitan area in South Korea. The results show that multi-scale urban aerodynamic roughness exploration is viable and can address differences in urban building data at various spatial resolutions. Although validating morphological multi-scale UCPs using dense tall towers is challenging, emerging low-cost and efficient methods can serve as substitutes. However, further efforts are required to link the measured z0 to building form regulations, such as floor area ratio, and expand RS research to obtain more quantitative and qualitative knowledge.

Atmospheric ammonia is a significant pollutant throughout the year, necessitating standardized measurement and identification of emission factors. We performed a quantized evaluation of ammonia concentrations at various locations in and around Seoul, South Korea. The established testing methods of the Radiello Passive Sampler were used for ammonia sampling, and the method was validated using annular denuder sampling. Urban and suburban areas were studied to gain a deeper understanding of the factors responsible for ammonia pollution. This study aimed to establish the fluctuations in concentration over one year, by analyzing the seasonal and regional variation in ammonia concentration. Livestock and agricultural areas recorded the highest concentration of ammonia among all sites, with the highest concentration recorded in autumn. However, at most of the other studied sites, the highest and lowest ammonia concentrations were recorded during summer and winter, respectively. This study attempted to establish a correlation between ammonia concentration and temperature, as well as ammonia concentration and altitude.

We report the results of year-long PM2.5 (particulate matter less than 2.5 µm in diameter) simulations over Northeast Asia for the base year of 2013 under the framework of the Long-range Transboundary Air Pollutants in Northeast Asia (LTP) project. LTP is a tripartite project launched by China, Japan, and Korea for cooperative monitoring and modeling of the long-range transport (LRT) of air pollutants. In the modeling aspect in the LTP project, each country’s modeling group employs its own original air quality model and options. The three regional air quality models employed by the modeling groups are WRF-CAMx, NHM-RAQM2, and WRF-CMAQ. PM2.5 concentrations were simulated in remote exit-and-entrance areas associated with the LRT process over China, Japan, and Korea. The results showed apparent bias that remains unexplored due to a series of uncertainties from emission estimates and inherent model limitations. The simulated PM10 levels at seven remote exit-and-entrance sites were underestimated with the normalized mean bias of 0.4 ± 0.2. Among the four chemical components of PM2.5 (SO42−, NO3−, organic carbon (OC), and elemental carbon (EC)), the largest inter-model variability was in OC, with the second largest discrepancy in NO3−. Our simulation results also indicated that under considerable SO42− levels, favorable environments for ammonium nitrate formation were found in exit-and-entrance areas between China and Korea, and gas-aerosol partitioning for semi-volatile species of ammonium nitrate could be fully achieved prior to arrival at the entrance areas. Other chemical characteristics, including NO3−/SO42− and OC/EC ratios, are discussed to diagnose the LRT characteristics of PM2.5 in exit-and-entrance areas associated with transboundary transport over China, Japan, and Korea.

With global anthropogenic black carbon (BC) emissions increasing, automobiles are significantly contributing as the major source of emissions. However, the appropriate regulations of BC emissions from vehicles are not in place. This study examined BC emissions following fuel types (gasoline, liquefied petroleum gas (LPG), and diesel) and engine combustion (gasoline direct injection (GDI) and multi-port injection (MPI) for gasoline vehicles) with emission regulations. To this end, chassis dynamometer and aethalometer (AE33) were used. Driving modes created by the National Institute of Environmental Research (NIER) and emission certification modes (CVS-75 and NEDC) for vehicles in Korea were used to determine BC emissions for various vehicle speeds. In addition, the contributions of biomass and coal combustion to the data of AE33 were analyzed to determine the possibility of tracking the BC sources. MPI, LPG, and EURO 6 with diesel particulate filter (DPF) vehicles emitted the lowest BC emissions in NIER modes. Among gasoline vehicles, MPI vehicles showed the lower BC content in PM emissions. Also, older vehicles in MPI vehicles emitted the high PM and BC emissions. The BC emissions of EURO 3 vehicles without DPF were the highest as the results of previous studies, and it was found that as emissions regulations were tightened, the level of BC results of diesel vehicles became similar with MPI vehicles. The average absorption Ångström exponent (AAE) from difference emissions sources were biomass combustion (oak wood) > coal combustion (the power plant stack) > automobile emissions (gasoline, LPG, diesel).

Biogenic volatile organic compound (BVOCs) emissions are the largest VOC emission source globally, and are precursors to ozone and secondary organic aerosols, both of which are strong, short-lived climate pollutants. BVOC emissions are usually estimated using the Model of Emissions of Gases and Aerosols from Nature (MEGAN), which requires Plant Functional Types (PFTs) and Leaf Area Indexes (LAIs) as inputs. Herein, the effects of refined input data on regional BVOC emission estimates are analyzed. For LAIs, lower resolution MODerate-resolution Imaging Spectroradiometer (MODIS), and higher spatio-temporal resolution Spatial and Temporal Adaptive Reflectance Fusion Model (STARFM) LAI were generated. For PFTs, local land cover maps were developed, in addition to MODIS PFT. In South Korea, annual emissions of isoprene and monoterpenes in 2015 were estimated as 384 and 160 Gg/year, respectively, using STARFM LAI and Local PFT (Case 4). For North Korea, 340 Gg/year isoprene and 72 Gg/year monoterpenes emissions were estimated using STARFM LAI and MODIS PFT. These estimates were 14–110% higher than when using MODIS LAI and MODIS PFT (Case 1). Inter-comparison with satellite-based inverse isoprene emission estimates from GlobEmission shows 32% (North Korea) to 34% (South Korea) overestimation in bottom-up data. Our new vegetation inputs improve MEGAN performance and resulting BVOC emission estimations. Performance of Weather Research and Forecasting (WRF) meteorological modeling requires improvement, especially for solar radiation, to avoid overestimation of isoprene emissions.

Gaseous emissions from vehicles contribute substantially to air pollution and climate change. Vehicular emissions also contain secondary pollutants produced via chemical reactions that occur between the emitted gases and atmospheric air. This study aims at understanding patterns concerning emission of regulated, greenhouse, and precursor gases, which demonstrate potential for secondary aerosol (SA) formation, from vehicles incorporating different engine technologies—multi-point injection (MPI) and gasoline direct injection (GDI)—and using different fuels—gasoline, liquefied petroleum gas (LPG), and diesel. Drive cycles from the National Institute of Environmental Research (NIER) were used in this study. Results obtained from drive cycle tests demonstrate a decline in aggregate gas emissions corresponding to an increase in average vehicle speed. CO2 accounts for more than 99% of aggregate gaseous emissions. In terms of concentration, CO and NH3 form predominantly non-CO2 emissions from gasoline and LPG vehicles, whereas nitrogen oxides (NOx) and non-methane hydrocarbons (NMHC) dominate diesel-vehicle emissions. A higher percentage of SO2 is emitted from diesel vehicles compared to their gasoline- and LPG-powered counterparts. EURO-5- and EURO-6-compliant vehicles equipped with diesel particulate filters (DPFs) tend to emit higher amounts of NO2 compared to EURO-3-compliant vehicles, which are not equipped with DPFs. Vehicles incorporating GDI tend to emit less CO2 compared to those incorporating MPI, albeit at the expense of increased CO emissions. The authors believe that results reported in this paper concerning regulated and unregulated pollutant-emission monitoring can contribute towards an accurate evaluation of both primary and secondary air-pollution scenarios in Korea.