Search

A series of laboratory and large-scale field model footing tests were conducted to assess the modulus and stress distribution behavior of a clayey soil foundation, both with/without geogrid reinforcement, deviating from the conventional approach of evaluating the strength performance, such as bearing capacity. The modulus was evaluated at three settlement ratios of s/B = 1, 3, and 5%, while the stress distribution angle α was estimated at three applied surface pressures of 234 kPa, 468 kPa, and 936 kPa. The results indicated a stiffer load-settlement response when geogrid reinforcement was included. The modulus of reinforced clayey soil remained nearly constant for test sections with the same reinforced ratio, with the modulus improvement increasing as the reinforced ratio (Rr) increased. The modulus improvement also increased with the settlement ratio (s/B). These results demonstrated that the stress distribution improvement decreased as the surface pressure increased. Generally, both the modulus and stress distribution improvement exhibited an increase with an increase in the tensile modulus of the geogrid. While laboratory model tests consistently provided a higher improvement in the modulus than large-scale field model tests in this study due to a higher reinforced ratio, the stress distribution improvement was similar for both.

Novel tetrafluoro-λ6-sulfanyl-containing oligomers prepared by visible light-promoted addition of 1,4-(bis-chlorotetrafluoro-λ6-sulfanyl) benzene or 1,3-(bis-chlorotetrafluoro-λ6-sulfanyl) benzene to either 1,4-diethynyl benzene or the 1,3-diethynyl isomers form hard, stress resistant thin films on spin casting. The isomeric oligomers were utilized to establish a structure-function relationship for the mechanical properties of films prepared from the oligomers. The Young’s moduli of 145-nm-thick cured films could reach 60 GPa. The measured hardnesses, between 1.57 and 2.77 GPa, were more than double those of polymethyl methacrylate (PMMA) films. Curing of the tetrafluoro-λ6-sulfanyl-containing polymer films by UV irradiation resulted in coatings that exhibited remarkable hardness and modulus with good surface adhesion to silicon.

Compared with an ordinary prefabricated housing project (PHP), a transnational PHP tends to involve more uncertainties, with major stakeholders residing in different countries. This study proposes a novel digital project management framework that integrates building information modeling to enhance information utilization. This framework also incorporates innovative design concepts of modulor, modulus, module, model, durability, and recyclability for enhanced user comfort, housing industrialization, and extended lifespan. It was demonstrated how planning, design, manufacture, and transportation processes can be streamlined in transnational PHP delivery. A case study was performed in a typical transnational PHP between the Kingdom of Saudi Arabia and China for validation. By applying the framework, this PHP could install a single house within 24 h, improve precast level by about 20%, and reduce project cost per square meter by 5.2%, because of integrated design concept, reduced labor cost, effective material cost control, and enhanced information management.

Surgical sutures play a crucial role in wound closure, facilitating the tissue-healing process across various fields of medicine. The objective of this study was to analyse the impact of seasoning time during the initial days/weeks of seasoning in Ringer’s solution on the mechanical properties of five commercial absorbable sutures: SafilQuick+®, Novosyn®, MonosynQuick®, Monosyn® and Monoplus®, each with different absorption periods. The results demonstrated that the SafilQuick+ and MonosynQuick sutures lost strength within 9–12 days, as evidenced by statistically significant changes in tensile strength. In contrast, the Novosyn and Monoplus sutures did not exhibit significant changes in strength during the study period. Statistical analysis confirmed significant differences in the behaviour of the individual sutures, highlighting the importance of selecting appropriate suture material in the context of the specific medical procedure.

Filler content in dental composites is credited for affecting its physical and mechanical properties. This study evaluated the correlation between the filler percentage and strength, modulus, shrinkage stress, depth of cure, translucency and radiopacity of commercially available high- and low-viscosity dental composites. Filler weight percentage (wt%) was determined through the burned ash technique (800 °C for 15 min). Three-point bend flexural strength and modulus were measured according to ISO 4049 with 2 mm × 2 mm × 25 mm bars. Shrinkage stress was evaluated using a universal testing machine in which composite was polymerized through two transparent acrylic rods 2 mm apart. Shrinkage was measured from the maximum force following 500 s. The translucency parameter (TP) was measured as the difference in color (ΔE00) of 1 mm thick specimens against white and black tiles. The depth of cure was measured according to ISO 4049 in a cylindrical metal mold (4 mm diameter) with a 10 s cure. Radiopacity was measured by taking a digital X-ray (70 kVp for 0.32 s at 400 mm distance) of 1 mm thick specimens and comparing the radiopacity to an aluminum step wedge using image analysis software. The correlation between the filler wt% and properties was measured by Pearson’s correlation coefficient using SPSS. There was a positive linear correlation between the filler wt% and modulus (r = 0.78, p < 0.01), flexural strength (r = 0.46, p < 0.01) and radiopacity (r = 0.36, p < 0.01) and negative correlation with translucency (r = −0.29, p < 0.01). Filler wt% best predicts the modulus and strength and, to a lesser extent, the radiopacity and translucency. All but two of the high- and low-viscosity composites from the same manufacturer had statistically equivalent strengths as each other; however, the high-viscosity materials almost always had a statistically higher modulus. For two of the flowable composites measured from the same manufacturer (3M and Dentsply), there was a lower shrinkage stress in the bulk-fill version of the material but not for the other two manufacturers (Ivoclar and Tokuyama). All flowable bulk-fill composites achieved a deeper depth of cure than the flowable composite from the same manufacturer other than Omnichroma Flow Bulk.

We look at a momentum map associated with the Heisenberg group. We show that the cocycle associated with its momentum mapping is the value of a modulus of an associated coadjoint orbit.

Hydraulic asphalt concrete is known for its excellent seepage control performance and strong deformation resistance. This engineering material has widespread applications in the seepage control structures of hydraulic buildings. Recent projects have investigated the use of acidic aggregates to improve economic efficiency. However, they have also highlighted the weaker adhesion between acidic aggregates and asphalt, which necessitates stringent construction process control. This study investigates the impact of resting conditions on the tensile properties of acidic aggregate hydraulic asphalt concrete. The results of the tensile testing indicate that the storage time significantly affects the performance of asphalt concrete. The tensile strength of the specimens without anti-stripping agents decreased from 1.711 MPa to 0.914 MPa after resting periods of 0, 10, 20, and 30 days. The specimens treated with anti-stripping agents also showed a decrease in tensile strength over time, similar to the trend observed in the previous specimens. Digital specimen simulations indicated a decrease in cohesion between the asphalt and the aggregate from 5.375 MPa to 2.664 MPa after 30 days, representing a reduction of 50.44%. To counteract the effect of the storage time on the bonding between acidic aggregates and asphalt, this study recommends reducing the grading index and maximum size of aggregates, decreasing the coarse aggregate content, and selecting smooth aggregate shapes.

Smart wearable sensors are increasingly integrated into everyday life, interfacing with the human body to enable real-time monitoring of biological signals. This study focuses on creating high-sensitivity capacitive-type sensors by impregnating polyester-based 3D spacer fabric with a Carbon Nanotube (CNT) dispersion. The unique properties of conductive particles lead to nonlinear variations in the dielectric constant when pressure is applied, consequently affecting the gauge factor. The results reveal that while the fabric without CNT particles had a gauge factor of 1.967, the inclusion of 0.04 wt% CNT increased it significantly to 5.210. As sensor sensitivity requirements vary according to the application, identifying the necessary CNT wt% is crucial. Artificial intelligence, particularly the Multilayer Perception (MLP) model, enables nonlinear regression analysis for this purpose. The MLP model created and validated in this research showed a high correlation coefficient of 0.99564 between the model predictions and actual target values, indicating its effectiveness and reliability.

Throughout all the countries in the world, including Vietnam, nations with well-established mining industries have undertaken extensive research on the stability of rock masses when constructing underground tunnels in varied geological conditions. The present study aims to provide a comprehensive overview of the risk assessment related to rock masses during the construction of pit lines in mining operations. Consequently, the standing time of unsupported tunnels is assessed based on different values of the strength index and deformation characteristics of the rock mass. The objective was to perform both experimental and theoretical investigations to analyse how the stand-up time of rock masses surrounding a tunnel affects the unsupported span. The analyses were based on considering the rock parameters, including strain modulus; geological strength index; and allowable displacement values, and consideration of hereditary creep properties. By examining tunnels excavated in rock strata, it was concluded that varying geological strength index values resulted in distinct creep behaviour in the surrounding rock masses. Thus, it was reasonable to compute the unsupported span and stand-up time of tunnels. The research revealed that permissible displacements are significantly influenced by the types of rock materials surrounding the tunnel structure. Recognising the significance of time, the authors introduce a more practical interpretation and evaluation of the stability of rock masses, thus enhancing the precision of commonly available models.

To promote resourceful utilization of argon oxygen decarburization (AOD) slag, this research developed a new three-ash stabilized recycled aggregate with AOD slag, cement, fly ash (FA), and recycled aggregate (RA) as raw materials. The AOD slag was adopted as an equal mass replacement for fly ash. The application of this aggregate in a road base layer was investigated in terms of its mechanical properties and mechanistic analysis. First, based on a cement: FA ratio of 1:4, 20 sets of mixed proportion schemes were designed for four kinds of cement dosage and AOD slag replacement rates (R/%). Through compaction tests and the 7-day unconfined compressive strength test, it was found that a 3% cement dosage met the engineering requirements. Then, the unconfined compressive strength test, indirect tensile strength test, compressive rebound modulus test, and expansion rate test were carried out at different age thresholds. The results showed that the mixture’s strength, modulus, and expansion rate increased initially and then stabilized with age, while the strength and modulus initially increased and then decreased with increasing R. Secondly, based on X-ray diffraction (XRD) and scanning electron microscopy (SEM) used to analyze the mechanism, it was found that the strength, modulus, and expansion rate of the new material can be promoted by blending AOD slag, due to its ability to fully stimulate the hydration reaction and pozzolanic reaction of the binder. Finally, based on the strength and modulus results, R = 3% was identified as the optimal ratio, which provides a reference point for the effective application of AOD slag and RA in road base materials.

As wind turbine power requirements have evolved from the order of kilowatts (kWs) to the order of several megawatts (MWs), wind turbine components have been subjected to more demanding and critical operating conditions. The wind turbine must cope with higher wind loads due to larger blade sizes, which are also time-varying, and, ultimately, higher power levels. One of the challenges in the manufacture of high-power wind turbines lies in the gearbox and consists of achieving ever-greater power density without compromising efficiency, i.e., greater load capacity with lower weight (and production cost) and reduced power losses. Epicyclic geartrains are used to build the gearbox due to various advantages in relation to conventional gear systems, such as higher feasible gear ratios, higher efficiency, compactnesss, and lower weight. In this paper, several epicyclic geartrains with different structures will be analysed to reveal the influence that certain design parameters have on the size and weight of the gearbox components in the selected model and, therefore, of the gearbox itself. For this purpose, the theoretical model of the gearbox will be planned and the influence of the calculation parameters on the gearbox design will be analyzed following ISO 6336. Special emphasis is placed on the influence of the material used; the modulus and tooth width on the size and weight of the gearbox will be observed. Critical stresses are also calculated. The goal is to prepare the theoretical basis for an optimization process subject to geometric, kinematic, and dynamic constraints that will result in a gearbox as compact, energy-dense, and light as possible without compromising the service life of the components.

Surgical sutures play a crucial role in wound closure, facilitating the tissue-healing process across various fields of medicine. The objective of this study was to analyse the impact of seasoning time during the initial days/weeks of seasoning in Ringer's solution on the mechanical properties of five commercial absorbable sutures: SafilQuick+ ® , Novosyn ® , MonosynQuick ® , Monosyn ® and Monoplus ® , each with different absorption periods. The results demonstrated that the SafilQuick+ and MonosynQuick sutures lost strength within 9-12 days, as evidenced by statistically significant changes in tensile strength. In contrast, the Novosyn and Monoplus sutures did not exhibit significant changes in strength during the study period. Statistical analysis confirmed significant differences in the behaviour of the individual sutures, highlighting the importance of selecting appropriate suture material in the context of the specific medical procedure.

Generally, the dynamic modulus and bending stiffness modulus are used to evaluate the mechanical properties of asphalt mixture, and they are also used as basic parameters for asphalt mixture design. Therefore, a study was conducted on changes in the dynamic modulus and bending stiffness modulus of hot-recycled asphalt mixture with high levels of reclaimed asphalt pavement (RAP) under the influence of different factors: dosage of regenerant, curing temperature, and curing time. The performance of reclaimed asphalt pavement (RAP) was first evaluated. Then, the hot-recycled asphalt mixture was adjusted and designed in order to conduct modulus experiments, composed of the dynamic modulus test and three-point bending test. Finally, the influencing factors were not only qualitatively but also quantitatively analyzed to clarify the change laws of the mechanical parameters of hot-recycled asphalt mixture. The results showed that the modulus of the recycled asphalt mixture first decreased, then increased, and then decreased with increasing dosage of regenerant. As the curing time or temperature increased, the modulus first decreased and then increased. In terms of the dynamic modulus of the hot-recycled asphalt mixture, the curing time had the greatest impact, followed by dosage of the regenerant and curing temperature. For bending stiffness modulus, the influence of dosage of the regenerant was the greatest, followed by curing time and curing temperature. For the bending stiffness modulus of hot-recycled asphalt mixture, the curing conditions had a greater influence compared with the dynamic modulus.

The current work is focused on numerical and experimental studies of woven fabric composites modified by hybridisation with biological (cellulosic) filler materials. The mechanical performance of the composites is characterized under tensile, bending and impact loads and the effect of hybridisation is observed with respect to pure and nonhybrid composites. Numerical models are developed using computational tools to predict mechanical performance under tensile loading. The computational prediction results are compared and validated with relevant experimental results. This research is aimed at understanding the mechanical performance of basalt–epoxy composites partially reinforced with micro-/nano-sized bio-fillers from cellulose and intended for various application areas. Different weave structures, e.g., plain, twill, matt, etc., were investigated with respect to the mechanical properties of the hybrid composites. The effects of hybridizing with cellulose particles and different weave patterns of the basalt fabric are studied. In general, the use of high-strength fibres such as basalt along with cellulosic fillers representing up to 3% of the total weight improves the mechanical performance of the hybrid structures. The thermomechanical performance of the hybrid composites improved significantly by using basalt fabric as well as by addition of 3% weight of cellulosic fillers. Results reveal the advantages of hybridisation and the inclusion of natural cellulosic fillers in the hybrid composite structures. The material developed is suitable for high-end applications in components for construction that demand advanced mechanical and thermomechanical performance. Furthermore, the inclusion of biodegradable fillers fulfills the objectives of sustainable and ecological construction materials.

Magnetic nanoparticles of NiFe2O4 were successfully prepared by utilizing the sol–gel techniques. The prepared samples were investigated through various techniques such as X-ray diffraction (XRD), transmission electron microscopy (TEM), dielectric spectroscopy, DC magnetization and electrochemical measurements. XRD data analysed using Rietveld refinement procedure inferred that NiFe2O4 nanoparticles displayed a single-phase nature with face-centred cubic crystallinity with space group Fd-3m. Average crystallite size estimated using the XRD patterns was observed to be ~10 nm. The ring pattern observed in the selected area electron diffraction pattern (SAED) also confirmed the single-phase formation in NiFe2O4 nanoparticles. TEM micrographs confirmed the uniformly distributed nanoparticles with spherical shape and an average particle size of 9.7 nm. Raman spectroscopy showed characteristic bands corresponding to NiFe2O4 with a shift of the A1g mode, which may be due to possible development of oxygen vacancies. Dielectric constant, measured at different temperatures, increased with temperature and decreased with increase in frequency at all temperatures. The Havrilliak–Negami model used to study the dielectric spectroscopy indicated that a NiFe2O4 nanoparticles display non-Debye type relaxation. Jonscher’s power law was utilized for the calculation of the exponent and DC conductivity. The exponent values clearly demonstrated the non-ohmic behaviour of NiFe2O4 nanoparticles. The dielectric constant of the nanoparticles was found to be >300, showing a normal dispersive behaviour. AC conductivity showed an increase with the rise in temperature with the highest value of 3.4 × 10−9 S/cm at 323 K. The M-H curves revealed the ferromagnetic behaviour of a NiFe2O4 nanoparticle. The ZFC and FC studies suggested a blocking temperature of ~64 K. The saturation of magnetization determined using the law of approach to saturation was ~61.4 emu/g at 10 K, corresponding to the magnetic anisotropy ~2.9 × 104 erg/cm3. Electrochemical studies showed that a specific capacitance of ~600 F g−1 was observed from the cyclic voltammetry and galvanostatic charge–discharge, which suggested its utilization as a potential electrode for supercapacitor applications.

A simple method for determining the effective elastic modulus of wavy single-wall carbon nanotubes (SWCNTs) is presented in this paper. The effective modulus of curved SWCNTs is derived using Castigliano’s theorem. The effect of curvature on the effective modulus is studied. This method is verified by finite element analysis (FEA). The distributions of effective moduli are studied by Monte Carlo simulation. The effective modulus of a general wavy SWCNT is derived by considering the SWCNT as a number of curved SWCNT sections.

Coatings with tunable refractive index and high mechanical resilience are useful in optical systems. In this work, thin films of HfO2 doped with Al2O3 were deposited on silicon at 300 °C by using plasma-enhanced atomic layer deposition (PE-ALD). The mainly amorphous 60–80 nm thick films consisted Al in the range of 2 to 26 at.%. The refractive indexes varied from 1.69 to 2.08 at the wavelength of 632 nm, and they consistently depended on the composition. The differences were higher in the UV spectral region. At the same time, the hardness of the films was from 12–15 GPa; the modulus was in the range of 160–180 GPa; and the mechanical properties did not have a good correlation with the deposited compositions. The deposition conditions, element contents, and refractive indexes at respective wavelengths were correlated. The results indicated that it is possible to tune optical properties and retain mechanical properties of atomic layer-deposited thin films of HfO2 with Al2O3 as doping oxide. Such films could be used as mechanically resilient and optically tunable coatings in, for instance, micro- or nano-electromechanical systems or transparent displays.

Structural coloring of dental resin-based composites (RBC) is used to create universal chromatic materials designed to meet any aesthetic need, replacing the mixing and matching of multiple shades. The microstructural adjustments to create this desideratum involve nanoscale organic–inorganic core–shell structures with a particular arrangement. The generally higher polymer content associated with these structures compared to universal chromatic RBCs colored by pigments, which in their microstructure come close to regularly shaded RBCs, can influence the way the material ages. Accelerated and slow aging up to 1.2 years of immersion in artificial saliva at 37 °C were therefore compared in relation to their effects on the materials described above and in relation to the immersion conditions prescribed by standards. Quasi-static and viscoelastic parameters were assessed to quantify these effects by a depth-sensing indentation test equipped with a DMA module. The microstructure of the materials was characterized by scanning electron microscopy. The results convincingly show a differentiated influence of the aging protocol on the measured properties, which was more sensitively reflected in the viscoelastic behavior. Accelerated aging, previously associated with the clinical behavior of RBCs, shows a 2- to 10-fold greater effect compared to slow aging in artificial saliva of up to 1.2 years, highly dependent on the microstructure of the material.

The physical, thermal, structural, and mechanical properties of poly(methyl methacrylate) PMMA foils cast from solutions of toluene were investigated by differential scanning calorimetry, optical microscope, Fourier infrared spectroscopy, and dynamical mechanical analysis. The PMMA foils were prepared from a different ratio of PMMA powder with toluene solvent by the solution cast method. The surface features, glass transition temperature, and C-H bonds of foils were investigated and compared with commercial PMMA foil. The mechanical characterization of foils was examined by using static and dynamic loads in axial and transverse modes. The tensile behaviors of the commercial and as-prepared foils were investigated by using a strain rate of 0.01/s. The dynamical behavior of the foils was tested in tensile mode using 0.1 N of stress with a frequency of 1 Hz for the determination of storage, loss modulus, and damping values of the tan delta. A significant shape memory was observed in all of the prepared PMMA foils. The solution cast method allows for tuning the glass transition temperature of polymer foil that could easily integrate with the NiTi alloy phase transition temperature to fabricate a suitable composite structure. Integrating both structures will open the flexibility in bistable actuators in composite structures as a function of thermal cycles.

In this work, Gd2O3 bulks were sintered at temperatures ranging from 1400 °C to 1600 °C for times from 6 h to 24 h, and their microstructure and properties were studied for a wider application of materials in thermal barrier coatings. The densification of the Gd2O3 bulk reached 96.16% when it was sintered at 1600 °C for 24 h. The elastic modulus, hardness, fracture toughness and thermal conductivity of the bulks all increased with the rise in sintering temperature and extension of sintering time, while the coefficient of thermal expansion decreased. When the Gd2O3 bulk was sintered at 1600 °C for 24 h, it had the greatest elastic modulus, hardness, fracture toughness and thermal conductivity of 201.15 GPa, 9.13 GPa, 15.03 MPa·m0.5 and 2.75 W/(m·k) (at 1100 °C), respectively, as well as the smallest thermal expansion coefficients of 6.69 × 10−6/°C (at 1100 °C).

The melt-quenching technique was used to synthesize tellurite glasses of the chemical composition 80TeO2-(20-x) ZnO-xV2O5. X-ray diffraction (XRD) patterns indicate the amorphous nature of the prepared glasses. Raman and FTIR measurements demonstrate a progressive substitution of the Te-O-Te linkages by the Te-O-V bridges and the formation of VO4 and VO5 units by a change of the vanadium coordination due to the higher number of oxygens incorporated by further addition of V2O5. The AC conductivity was investigated in the frequency range of 40 Hz to 107 Hz between 473 K to 573 K. A good coherence of the AC conductivity was found using a model correlating the barrier hopping (CPH) and the dominant conduction process changes from ionic to polaronic with the addition of V2O5. The dielectric constant exhibits high values in the range of lower and medium frequencies. Both variations of the electric modulus and the dielectric loss parameters with frequency and temperature showed a relaxation character mainly assigned to the vanadate phases. The electric modulus displays a non-Debye dielectric dispersion and a relaxation process. The present results open the door to future zinc-tellurite glasses-doped vanadium exploitation as a potential electrolyte-based material for solid-state batteries.

Polymeric hydrogels have drawn considerable attention as a biomedical material for their unique mechanical and chemical properties, which are very similar to natural tissues. Among the conventional hydrogel materials, self-healing hydrogels (SHH) are showing their promise in biomedical applications in tissue engineering, wound healing, and drug delivery. Additionally, their responses can be controlled via external stimuli (e.g., pH, temperature, pressure, or radiation). Identifying a suitable combination of viscous and elastic materials, lipophilicity and biocompatibility are crucial challenges in the development of SHH. Furthermore, the trade-off relation between the healing performance and the mechanical toughness also limits their real-time applications. Additionally, short-term and long-term effects of many SHH in the in vivo model are yet to be reported. This review will discuss the mechanism of various SHH, their recent advancements, and their challenges in tissue engineering, wound healing, and drug delivery.

In this paper, we present an extensive experimental study on the dynamic mechanical properties of composites with polymer matrices, as well as a quantification of the parameters that influence these properties. Polymer-composite matrices make it possible to form any reinforcement arrangement of fibres, particles, and layers, which makes it possible to form composite materials with certain dominant mechanical properties according to the internal arrangement for the application. In this study, we focused on the dynamic properties (i.e., damping parameters, such as the loss factor (tan d), logarithmic decrement (λ), storage modulus (E′), and loss modulus (E″)) of composites with polymer matrices, including parameters such as the fibre material, fabric weaving, fibre orientation, temperature, frequency, particle size, volume of short fibres, and epoxy resin type. If other articles focus on one type of composite and 1–2 parameters, then the benefit of this article lies in our analysis of 8 mentioned parameters in the experimental analysis of 27 different types of composites with polymer matrices. The tested fibre materials were glass, aramid, and carbon; the tested woven fabrics were twill, plain, unidirectional, and satin; the temperature range was from −50 to +230 °C; the frequency was 1 Hz and 10 Hz; the particle size was 0.1–16 mm; the volume percentages of the short fibres were 3, 6, and 12 vol.% of the hybrid polymer composites and the type of polymer matrix. We used the free-damped-vibration method with vibration dynamic signal analysis and the forced-damped vibration of dynamic mechanical thermal analysis for testing. We ranked the parameters that influence the dynamic vibration properties according to the effects. Among sets of results provided in the paper, considering the storage modulus, loss modulus, and loss factor, the best results of the fibre composites were for aramid-fibre-reinforced polymers, regardless of the weave type, with an advantage for unidirectional fabric. The best results of the particle composites were for those with fine filler sizes that incorporated the short fibres.

To date, there have been a limited number of studies modeling the tensile modulus in the polymer halloysite nanotube (HNT) systems before or after percolation onset. In this paper, an equation for a composite’s modulus post-percolation onset was developed for HNT-filled samples including the interphase and HNT network. The dispersed nanoparticles and adjoining interphase part were neglected, because they caused ineffective influences on the stiffness of the system after percolation onset. The developed model reflects the impacts of HNTs’ size, interphase depth, percolation onset and the volume shares and moduli of the HNT network and its adjacent interphase on the modulus of HNT-based systems. The impacts of issues on the nanocomposite modulus are defendable, confirming the effectiveness of the developed model. HNT length, interphase depth, HNT concentration, net modulus and net portion directly influenced the stiffness, while the HNT radius and percolation onset had inverse effects. Results show that there was a 142% improvement in the modulus of samples at an interphase depth of 40 nm. Moreover, the stiffness improved by 60% at a net modulus of 200 GPa, but it later exhibited a 180% enhancement at a net modulus of 1000 GPa. In addition, the experimental data for the modulus of numerous composites display fine agreement to the predictions, confirming the validity of the developed model.

The objective was to evaluate new commercially available ion-releasing restorative materials and compare them to established anti-cariogenic materials. Four materials were tested: alkasite Cention (Ivoclar Vivadent) in self-cure or light-cure mode, giomer Beautifil II (Shofu), conventional glass-ionomer Fuji IX (GC), and resin composite Tetric EvoCeram (Ivoclar Vivadent) as a control. Flexural strength, flexural modulus, and Weibull modulus were measured one day, three months, and after three months with accelerated aging in ethanol. Water sorption and solubility were evaluated for up to one year. Degree of conversion was measured during 120 min for self-cured and light-cured Cention. In this study, Beautifil II was the ion-releasing material with the highest flexural strength and modulus and with the best resistance to aging. Alkasite Cention showed superior mechanical properties to Fuji IX. Weibull analysis showed that the glass-ionomer had the least reliable distribution of mechanical properties with the highest water sorption. The solubility of self-cured alkasite exceeded the permissible values according to ISO 4049. Degree of conversion of light-cured Cention was higher than in self-cure mode. The use of alkasite Cention is recommended only in the light-cure mode.

Nanoindentation is widely used to investigate the surface-mechanical properties of biocomposites. In this study, polypropylene random copolymer (PPRC) and biowaste rice husk (BRH) were used as the main raw materials, and glass-fiber-reinforced polypropylene and talc were also used with BRH to enhance the mechanical characterization of the biocomposites. The interfacial bonding between the polymer and the rice husk was increased by treating them with maleic anhydride and NaOH, respectively. The results obtained from the nanoindentation indicated that the plastic behavior of the biocomposites was prominent when untreated BRH was used and vice versa. The modulus and hardness of the biocomposite improved by 44.8% and 54.8% due to the neat PPRC, respectively. The tribological properties were studied based on the hardness-to-modulus ratio and it was found that BRH- and talc-based biocomposites were better than other samples in terms of low friction and wear rate. The creep measurements showed that untreated rice husk biocomposite exhibited high resistance to load deformation.

Magnesium-doped zinc oxide “ZnO:Mg” nanocrystals (NCs) were fabricated using a sol gel method. The Mg concentration impact on the structural, morphological, electrical, and dielectric characteristics of ZnO:Mg NCs were inspected. X-ray diffraction (XRD) patterns display the hexagonal wurtzite structure without any additional phase. TEM images revealed the nanometric size of the particles with a spherical-like shape. The electrical conductivity of the ZnO NCs, thermally activated, was found to be dependent on the Mg content. The impedance spectra were represented via a corresponding circuit formed by a resistor and constant phase element (CPE). A non-Debye type relaxation was located through the analyses of the complex impedance. The conductivity diminished with the incorporation of the Mg element. The AC conductivity is reduced by raising the temperature. Its plot obeys the Arrhenius law demonstrating a single activation energy during the conduction process. The complex impedance highlighted the existence of a Debye-type dielectric dispersion. The various ZnO:Mg samples demonstrate high values of dielectric constant with small dielectric losses for both medium and high-frequency regions. Interestingly, the Mg doping with 3% content exhibits colossal dielectric constant (more than 2 × 104) over wide temperature and frequency ranges, with Debye-like relaxation. The study of the electrical modulus versus the frequency and at different temperatures confirms the non-Debye relaxation. The obtained results reveal the importance of the ZnO:Mg NCs for device applications. This encourages their application in energy storage.

The use of carbon nanofibers (CNFs) in cement systems has received significant interest over the last decade due to their nanoscale reinforcing potential. However, despite many reports on the formation of localized CNF clusters, their effect on the cement paste micromechanical properties and relation to the mechanical response at the macroscopic scale are still not fully understood. In this study, grid nanoindentation coupled with scanning electron microscopy and energy dispersive spectroscopy was used to determine the local elastic indentation modulus and hardness of a portland cement paste containing 0.2% CNFs with sub-micro and microscale CNF clusters. The presence of low stiffness and porous assemblage of phases (modulus of 15–25 GPa) was identified in the cement paste with CNFs and was attributed primarily to the interfacial zone surrounding the CNF clusters. The CNFs favored the formation of higher modulus C–S–H phases (>30 GPa) in the bulk paste at the expense of the lower stiffness C–S–H. Nanoindentation results combined with a microscale–macroscale upscaling homogenization method further revealed an elastic modulus of the CNF clusters in the range from 18 to 21 GPa, indicating that the CNF clusters acted as compliant inclusions relative to the cement paste.

Gd and Yb elements have high chemical stability, which can stabilize the solid solution in ZrO2. Gd2O3 and Yb2O3 have high melting points, and good oxidation resistance in extreme environments, stable chemical properties. Therefore, Gd2O3 and Yb2O3 were added to ZrO2 to stabilize oxides, improve the high temperature stability, and effectively decrease the thermal conductivity at high temperature. In this work, 5 wt% Yb2O3 and 5 wt%, 10 wt%, 15 wt% Gd2O3 were doped into 8 wt% Y2O3 stabilized ZrO2 (8YSZ) powders as thermal barrier coating materials, and sintered at 1650 °C for 6 h, 12 h, 24 h. The effects of Gd2O3 addition on the microstructure, density, thermal conductivity, hardness, and fracture toughness of Gd2O3-Yb2O3-Y2O3-ZrO2 (GYYZO) bulk composite ceramics were investigated. It was found that the densification of the 8YSZ bulk and GYYZO bulk with 15 wt% Gd2O3 reached 96.89% and 96.22% sintered at 1650 °C for 24 h. With the increase of Gd2O3 addition, the hardness, elastic modulus and fracture toughness of the GYYZO bulk increased and the thermal conductivity and thermal expansion coefficient of the GYYZO bulk decreased. GYYZO bulk with 15 wt% Gd2O3 sintered at 1650 °C for 24h had the highest hardness, elastic modulus and fracture toughness of 15.61 GPa, 306.88 GPa, 7.822 MPa·m0.5, and the lowest thermal conductivity and thermal expansion coefficient of 1.04 W/(m·k) and 7.89 × 10−6/°C at 1100 °C, respectively. The addition of Gd2O3 into YSZ could not only effectively reduce the thermal conductivity but also improve the mechanical properties, which would improve the thermal barrier coatings’ performances further.

This study presents a rigorous approach for the extraction of the modulus of soil and unbound aggregate base materials for quality management using intelligent compaction (IC) technology. The proposed approach makes use of machine-learning methods in tandem with IC technology and modulus-based spot testing as a local calibration process to estimate the mechanical properties of compacted geomaterials. A calibrated three-dimensional finite element (FE) model that simulates the proof-mapping process of compacted geomaterials was used to develop a comprehensive database of responses of a wide range of single and two-layered geosystems. The database was then used to develop different inverse solvers using artificial neural networks for the estimation of the modulus from the characteristics of the roller and information about the geomaterials. Several instrumented test sites were used for the evaluation and validation of the inverse solvers. The proposed approach was found promising for the extraction of the modulus of compacted geomaterials using IC. The accuracy of the inverse solvers is enhanced if a local calibration process is incorporated as part of a quality management program that includes the use of in situ measurements using modulus-based test devices and laboratory resilient modulus testing. Moreover, compaction uniformity plays a key role in the retrieval of the modulus of geomaterials with certainty. The proposed approach fuses artificial intelligence with mechanistic solutions to position IC as a technology that is well suited for the quality management of compacted materials.

It has previously been shown that optimum particle size distributions with a maximum packing fraction can be achieved from a straight line plot of the accumulated sum of particle volume fractions versus the square root of particle size. This study addresses practical limits for two dominant fundamental approaches to designing particle size distributions to address the effect on a specific physical property such as viscosity. The two fundamental approaches to obtain such a straight line would include: the first design approach would be generated utilizing the same initial particle size, Dmin, but by using different ultimate particle sizes, Dmax. The second design approach would be generated where each distribution starts with the same initial particle size, Dmin, and ends with the same ultimate particle size, Dmax. The first design approach is particularly useful to identify the possible slopes available based on the smallest and largest particle sizes available. The second design approach can be utilized to identify the preferred ratio between particles, Z, and the number of different particle sizes, n, to be utilized in the final particle blend. The extensive empirical experimental evaluations of particle size distributions generated by McGeary were then utilized to confirm the limits.

In materials science and engineering, a significant amount of research has been carried out using indentation techniques in order to characterize the mechanical properties and microstructure of a broad range of natural and engineered materials. However, there are many unresearched or partly researched areas, such as, for example, the investigation of the shape of the indentation load–displacement curve, the associated mechanism in porous materials with clastic texture, and the influence of the texture on the constitutive behavior of the materials. In the present study, nanoindentation is employed in the analysis of the mechanical behavior of a benchmark material composed of plaster of Paris, which represents a brand of highly porous-clastic materials with a complex structure; such materials may find many applications in medicine, production industry, and energy sectors. The focus of the study is directed at the examination of the influence of the porous structure on the load–displacement response in loading and unloading phases based on nanoindentation experiments, as well as the variation with repeating the indentation in already indented locations. Events such as pop-in in the loading phase and bowing out and elbowing in the unloading phase of a given nanoindentation test are studied. Modulus, hardness, and the elastic stiffness values were additionally examined. The repeated indentation tests provided validations of various mechanisms in the loading and unloading phases of the indentation tests. The results from this study provide some fundamental insights into the interpretation of the nanoindentation behavior and the viscoelastic nature of porous-clastic materials. Some insights on the influence of indentation spacing to depth ratio were also obtained, providing scope for further studies.

Elliptic Curve Factorization Method (ECM) is the general-purpose factoring method used in the digital computer era. It is based on the medium length of the modulus; ECM is an efficient algorithm when the length of modulus is between 40 and 50 digits. In fact, the main costs for each iteration are modular inverse, modular multiplication, modular square and greatest common divisor. However, when compared to modular multiplication and modular square, the costs of modular inverse and greatest common divisor are very high. The aim of this paper is to improve ECM in order to reduce the costs to compute both of modular inverse and greatest common divisor. The proposed method is called Fast Elliptic Curve Factorization Method (F-ECM). For every two adjacent points on the curve, only one modular inverse and one greatest common divisor will be computed. That means it implies that the costs in both of them can be split in half. Furthermore, the length of modulus in the experiment spans from 30 to 65 bits. The experimental results show that F-ECM can finish the task faster than ECM for all cases of the modulus. Furthermore, the computation time is reduced by 30 to 38 percent.

Macromolecular components of the vascular extracellular matrix (ECM), particularly elastic fibers and collagen fibers, are critical for the proper physiological function of arteries. When the unique biomechanical combination of these fibers is disrupted, or in the ultimate extreme where fibers are completely lost, arterial disease can emerge. Bioengineers in the realms of vascular tissue engineering and regenerative medicine must therefore ideally consider how to create tissue engineered vascular grafts containing the right balance of these fibers and how to develop regenerative treatments for situations such as an aneurysm where fibers have been lost. Previous work has demonstrated that the primary cells responsible for vascular ECM production during development, arterial smooth muscle cells (SMCs), can be induced to make new elastic fibers when exposed to secreted factors from adipose-derived stromal cells. To further dissect how this signal is transmitted, in this study, the factors were partitioned into extracellular vesicle (EV)-rich and EV-depleted fractions as well as unseparated controls. EVs were validated using electron microscopy, dynamic light scattering, and protein quantification before testing for biological effects on SMCs. In 2D culture, EVs promoted SMC proliferation and migration. After 30 days of 3D fibrin construct culture, EVs promoted SMC transcription of the elastic microfibril gene FBN1 as well as SMC deposition of insoluble elastin and collagen. Uniaxial biomechanical properties of strand fibrin constructs were no different after 30 days of EV treatment versus controls. In summary, it is apparent that some of the positive effects of adipose-derived stromal cells on SMC elastogenesis are mediated by EVs, indicating a potential use for these EVs in a regenerative therapy to restore the biomechanical function of vascular ECM in arterial disease.

The longevity of indirect restorations is primarily determined by the appropriate selection of the luting material. The function of a luting material is to seal the restoration and hold it in place for the time required for service. The mechanical behavior of luting materials and in particular their aging behavior, therefore, play a decisive role. The study provides a comparative analysis of the static and dynamic mechanical behavior of the most commonly used luting material categories—zinc phosphate cement, glass–ionomer cement, resin-modified glass–ionomer cement, resin-based composites, and self-adhesive resin-based composites—and their aging behavior. It also takes into account that luting materials are viscoelastic materials, i.e., materials that respond to external loading in a way that lies between an elastic solid and a viscous liquid. Flexural strength and modulus were determined in a three-point bending test followed by fractography analysis. The quasi-static and viscoelastic behavior was analyzed by a depth-sensing indentation test provided with a dynamic mechanical analysis (DMA) module at 20 different frequencies (1–50 Hz). The fracture toughness was evaluated in a notchless triangular prism (NTP) test. Material type exhibits the strongest influence on all measured properties, while the effect of aging becomes more evident in the material reliability. The variation of the viscoelastic parameters with aging reflects cement maturation or polymer plasticization.

Energy storage and dissipation by composite materials are important design parameters for sensors and other devices. While polymeric materials can reversibly store energy by decreased chain randomness (entropic loss) they fail to be able to dissipate energy effectively and ultimately fail due to fatigue and molecular chain breakage. In contrast, composite tissues, such as muscle and tendon complexes, store and dissipate energy through entropic changes in collagen (energy storage) and viscous losses (energy dissipation) by muscle fibers or through fluid flow of the interfibrillar matrix. In this paper we review the molecular basis for energy storage and dissipation by natural composite materials in an effort to aid in the development of improved substrates for sensors, implants and other commercial devices. In addition, we introduce vibrational optical coherence tomography, a new technique that can be used to follow energy storage and dissipation by composite materials without physically touching them.

To prevent a premature failure, absorbable magnesium implants must possess an adequate mechanical stability. Among many ways to improve the mechanical properties of magnesium is by particle reinforcement, such as using carbon nanofiber (CNF). This work reports an experimental design for optimum materials and processing of CNF-reinforced Mg–Zn composites based on a two-level factorial design. Four factors were analyzed: percentage of CNF, compaction pressure, sintering temperature, and sintering time, for three recorded responses: elastic modulus, hardness, and weight loss. Based on the two-level factorial design, mechanical properties and degradation resistance of the composites reach its optimum at a composition of 2 wt % CNF, 400 MPa of compaction pressure, and 500 °C of sintering temperature. The analysis of variance reveals a significant effect of all variables (p < 0.0500) except for the sintering time (p > 0.0500). The elastic modulus and hardness reach their highest values at 4685 MPa and 60 Hv, respectively. The minimum and maximum weight loss after three days of immersion in PBS are recorded at 54% and 100%, respectively. This work concludes the percentage of CNF, compaction pressure, and sintering temperature as the main factors affecting the optimum elastic modulus, hardness, and degradation resistance of CNF-reinforced Mg–Zn composites.

In this work, the effects of chemical pretreatment and different fiber loadings on mechanical properties of the composites at the sub-micron scale were studied through nanoindentation. The composites were prepared by incorporating choline chloride (ChCl) pretreated rice husk waste (RHW) in low-density polyethylene (LDPE) using melt processing, followed by a thermal press technique. Nanoindentation experiments with quasi continuous stiffness mode (QCSM) were performed on the surface of produced composites with varying content of pretreated RHW (i.e., 10, 15, and 20 wt.%). Elastic modulus, hardness, and creep properties of fabricated composites were measured as a function of contact depth. The results confirmed the appreciable changes in hardness, elastic modulus, and creep rate of the composites. Compliance curves indicated that the composite having 20 wt.% of pretreated RHW loading was harder compared to that of the pure LDPE and other composite samples. The values of elastic modulus and hardness of the composite containing 20 wt.% pretreated RHW were increased by 4.1% and 24% as compared to that of the pure LDPE, respectively. The creep rate of 42.65 nm/s and change in depth of 650.42 nm were also noted for the composite with RHW loading of 20 wt.%, which showed the substantial effect of holding time at an applied peak load of 100 mN. We believe that the developed composite could be a promising biodegradable packaging material due to its good tribo-mechanical performance.

In this study, the influence of alloying elements on the mechanical properties of iron borides FeB and Fe2B formed in Fe-B-X (X = C, Cr, Mn, V, W, Mn + V) alloys were evaluated using instrumented indentation measurement. The microstructural characterization of the alloys was performed by means of X-ray diffraction and scanning electron microscope equipped with an energy dispersive X-ray analyzer. The fraction of the phases present in the alloys was determined either by the lever rule or by image analysis. The hardest and stiffest FeB formed in Fe-B-X (X = C, Cr, Mn) alloys was observed in the Fe-B-Cr alloys, where indentation hardness of HIT = 26.9 ± 1.4 GPa and indentation modulus of EIT = 486 ± 22 GPa were determined. The highest hardness of Fe2B was determined in the presence of tungsten as an alloying element, HIT = 20.8 ± 0.9 GPa. The lowest indentation hardness is measured in manganese alloyed FeB and Fe2B. In both FeB and Fe2B, an indentation size effect was observed, showing a decrease of hardness with increasing indentation depth.

The paper is concerned with complex fuzzy numbers and complex fuzzy inner product spaces. In the classical complex number set, a complex number can be expressed using the Cartesian form or polar form. Both expressions are needed because one expression is better than the other depending on the situation. Likewise, the Cartesian form and the polar form can be defined in a complex fuzzy number set. First, the complex fuzzy numbers (CFNs) are categorized into two types, the polar form and the Cartesian form, as type I and type II. The properties of the complex fuzzy number set of those two expressions are discussed, and how the expressions can be used practically is shown through an example. Second, we study the complex fuzzy inner product structure in each category and find the non-existence of an inner product on CFNs of type I. Several properties of the fuzzy inner product space for type II are proposed from the modulus that is newly defined. Specfically, the Cauchy-Schwartz inequality for type II is proven in a compact way, not only the one for fuzzy real numbers. In fact, it was already discussed by Hasanhani et al; however, they proved every case in a very complicated way. In this paper, we prove the Cauchy-Schwartz inequality in a much simpler way from a general point of view. Finally, we introduce a complex fuzzy scalar product for the generalization of a complex fuzzy inner product and propose to study the condition for its existence on CFNs of type I.

Nano-indentation, a depth sensing technique, is a useful and exciting tool to investigate the surface mechanical properties of a wide range of materials, particularly polymers. Knowledge of the influence of experimental conditions employed during nano-indentation on the resultant nano-mechanical response is very important for the successful design of engineering components with appropriate surface properties. In this work, nano-indentation experiments were carried out by selecting various values of frequency, amplitude, contact depth, strain rate, holding time, and peak load. The results showed a significant effect of amplitude, frequency, and strain rate on the hardness and modulus of the considered polymer, ultrahigh molecular weight polyethylene (UHMWPE). Load-displacement curves showed a shift towards the lower indentation depths along with an increase in peak load by increasing the indentation amplitude or strain rate. The results also revealed the strong dependence of hardness and modulus on the holding time. The experimental data of creep depth as a function of holding time was successfully fitted with a logarithmic creep model (R2 ≥ 0.98). In order to remove the creeping effect and the nose problem, recommended holding times were proposed for the investigated polymer as a function of different applied loads.

Modified soybean oil (MSO) is synthesized from soybean oil (SO) and sulfur, aiming to reduce the double bond quantity of SO and avoid harmful effects on the crosslink density and mechanical properties of rubber. MSO modified with different weight percentages of sulfur is then used to plasticize tire tread rubber (TR). It is found that the crosslink density and modulus of MSO- plasticized rubber are significantly improved compared with that of SO-plasticized TR. MSO modified with 6 wt % sulfur (MSO-6%) exhibits the best plasticization effect on TR, thus, the plasticization effect of MSO-6% on TR was further studied by adjusting its additive content. Thereafter, the Mooney viscosity, Payne effect, mechanical property of different amount of MSO-6% plasticized TR are studied to investigate their plasticization effect. At the same additive content of plasticizer, the plasticization effect of MSO-6% and a commonly used aromatic hydrocarbon plasticizer (AO) is compared to determine the potential application of MSO on tire tread rubber. It is found MSO shows similar plasticization effect on TR compared with AO. More important, the aging resistance property and wear resistance property of MSO-6% plasticized rubber are better than those of AO-plasticized rubber. Therefore, MSO-6% is a promising bio-based plasticizer for tire tread rubber.

In this paper, theoretical models of the critical indentation depth and critical force on brittle materials using cleavage strength and contact theory are proposed. A Berkovich indenter is adopted for nanoindentation tests on a 4H-SiC single crystal sample to evaluate its mechanical behaviors. The stages of brittle material deformation (elastic, plastic, and brittle) can be characterized by the load versus indentation depth curves through the nanoindentation test. The curve of the elastic deformation stage follows the Hertz contact theory, and plastic deformation occurs at an indentation depth of up to 10 nm. The mechanism of 4H-SiC single crystal cracking is discussed, and the critical indentation depth and critical force for the plastic−brittle transition are obtained through the occurrence of the pop-in point. This shows that the theoretical results have good coherence with the test results. Both the values of the elastic modulus and hardness decrease as the crack length increases. In order to obtain more accurate mechanical property values in the nanoindentation test for brittle materials such as SiC, GaN, and sapphire, an appropriate load that avoids surface cracks should be adopted.

The gear is one of the important parts of a rotary gearbox. Once catastrophic gear failure occurs, it will cause a great threat to production and life safety. The crack is an important failure factor causing changes in time-varying stiffness and vibration response. It is difficult to effectively identify the vibration response and meshing stiffness changes when there is a fine crack in the gear. Therefore, it is of great importance to improve the accuracy of meshing stiffness calculation and dynamic simulations under micro-cracks. Investigations of meshing stiffness and the vibration response of a gearbox is almost all about fixed gear shape parameters. However, the actual production process of gear system needs to change gear shape parameters. In this paper, the meshing stiffness and vibration response of the dynamic simulation signals of gear teeth with different crack depths at different tooth shape parameters (the pressure angle, the modulus, and the tooth number) were calculated, respectively. The influence of cracks on the vibration response was investigated by the fault detection indicators, the Root Mean Square (RMS), the kurtosis, and the crest factor. The result shows that when the pressure angle and modulus change, the vibration response changes erratically. However, when the tooth numbers change, the vibration response changes regularly. The results could be a guide for choosing gears in different shape parameters when system stability is the aim.

Foam concrete is a low-density controlled strength material that can potentially be used for accommodating different types of particles—recycled fine aggregate being an example. The paste matrix of this material has a cellular microstructure, and bulk performance is readily affected by the inclusion of fines. To study the effect of inclusion of fines on mechanical performance and foam structure of foam concrete, a group of 0.55 g/cm3 foam–sand composite mixtures with high-volume fly ash replacement are investigated. The elastic modulus is measured by a vibrational frequency test. The crushing mechanics are determined by the load-displacement response from a penetration test. The effect of particle inclusion on the foam concrete microstructure is characterized using micro computed tomography. The results indicate that use of fine-graded sand particles at a small dosage simultaneously reduces cement content and enhances the crushing performance, however poor material performance is observed for a high sand content. The cellular structure of the foam–sand composite, and thus its mechanical behavior, can be substantially diminished by larger sand particles, especially when the particle size is larger than the voids in foam.

In this paper, the authors introduce the Orlicz spaces corresponding to the Young function and, by virtue of the equivalent theorem between the modified K-functional and modulus of smoothness, establish the direct, inverse, and equivalent theorems for linear combinations of modified summation operators of integral type in the Orlicz spaces.