Search

Inter-satellite links (ISLs) can improve the performance of the Global Navigation Satellite System (GNSS) in terms of precise orbit determination, communication, and data-exchange capabilities. This research aimed to evaluate a simulation-based processing strategy involving the exploitation of ISLs in orbit determination of Galileo satellites, which are not equipped with operational ISLs. The performance of the estimation process is first tested based on relative weighting coefficients obtained with methods of variance component estimation (VCE) varying in the complexity of the calculations. Inclusion of biases in the ISL measurements allows evaluation of the processing strategy and assessment of the impact of three different sets of ground stations: 44 and 16 stations distributed globally and 16 located in Europe. The results indicate that using different VCE approaches might lower orbit errors by up to 20% with a negligible impact on clock estimation. Depending on the applied ISL connectivity scheme, ISL range bias can be estimated with RMS between 10% to 30% of initial bias values. The accuracy of bias estimation may be associated with weighting approach and the number of ground stations. The results of this study show how introducing VCE with various simulation parameters into the processing chain might increase the accuracy of the orbit estimation.

Coastal sea level is observed at tide gauge stations, which usually also serve as height reference stations for national networks. One of the main issues with using tide gauge data for sea level research is that only a few stations are connected to permanent GNSS stations needed to correct for vertical land motion. As a new observation technique, absolute positioning by SAR using off the shelf active radar transponders can be installed instead. SAR data for the year 2020 are collected at 12 stations in the Baltic Sea area, which are co-located to tide gauges or permanent GNSS stations. From the SAR data, 3D coordinates are estimated and jointly analyzed with GNSS data, tide gauge records and regional geoid height estimates. The obtained results are promising but also exhibit some problems related to the electronic transponders and their performance. At co-located GNSS stations, the estimated ellipsoidal heights agree in a range between about 2 and 50 cm for both observation systems. From the results, it can be identified that, most likely, variable systematic electronic instrument delays are the main reason, and that each transponder instrument needs to be calibrated individually. Nevertheless, the project provides a valuable data set, which offers the possibility of enhancing methods and procedures in order to develop a geodetic SAR positioning technique towards operability.

Since pentlandites are among the most promising catalysts for hydrogen evolution reactions (HER), in this study, we investigated the influence of different cobalt, iron, and nickel substitutions in the cationic sublattice and the form of the material (powder, ingot, sintered pellet) on catalytic performance. This complements previous results regarding a multi-component approach in these chalcogenides. It was shown that in the case of sulfur-rich pentlandites with a non-equimolar ratio of Co, Fe, and Ni, the impact of intrinsic material properties is smaller than the surface-related effects. Among powder forms, catalysts based on a combination of Fe and Co perform the best. However, in volumetric forms, extremely high contents of individual metals are favorable, albeit they are associated with active precipitations of foreign phases. The presence of these phases positively affects the recorded currents but slows down the reaction kinetics. These findings shed light on the nuanced interplay between material composition, form, and HER properties, offering insights for tailored catalyst design.

Cu2−xS and Cu2−xSe (0 ≤ x ≤ 0.2) alloys stand out as highly promising materials for thermoelectric applications, owing to the phonon–liquid electron–crystal (PLEC) convention. In this study, we undertake a comprehensive investigation to reassess the synthesis conditions, with a focus on achieving pure-phased systems through a direct reaction between elements at elevated temperatures. Simultaneously, we present experimental evidence showcasing the feasibility of doping these systems with Ag, Ni, and Zn. The study demonstrates that obtaining single-phased systems requires multi-step processes, and the dissolution of chosen impurities appears doubtful, as evidenced by numerous foreign phase segregations. Additionally, it is revealed that the partial dissolution of individual impurities deteriorates the operational parameters of these chalcogenides. For the optimal Cu1.97S composition, it reduces the thermoelectric figure-of-merit ZT from 1.5 to approximately 1.0, 0.65, and 0.85 for Ag-, Ni-, and Zn-doped systems, respectively, while marginally improving their stability. For metal-like Cu1.8Se, the ZT parameter remains at a low level, ranging between 0.09 and 0.15, showing slight destabilization during subsequent operating cycles. The article concludes with an in-depth analysis of the basic thermoelectric performance exhibited by these doped systems, contributing valuable insights into the potential enhancements and applications of Cu2−xS and Cu2−xSe alloys in the field of thermoelectric materials.

In this study, graphene flakes were obtained using an electrolytic method and characterized using X-ray diffraction (XRD), Raman and FTIR spectroscopy, scanning and transmission electron microscopy (SEM/TEM). Graphene-based composites with varying concentrations of 0.5%, 1% and 3% by weight were prepared with acrylic paint, enamel and varnish matrices. The mechanical properties were evaluated using micro-hardness testing, while wettability and antimicrobial activity against three pathogens (Staphylococcus aureus 33591, Pseudomonas aeruginosa 15442, Candida albicans 10231) were also examined. The results indicate that the addition of graphene flakes significantly enhances both the mechanical and antimicrobial properties of the coatings.

The article presents the results of ultrasonic testing of Ti6Al4V material produced by the conventional method and the laser bed fusion method. Modern manufacturing techniques, such as additive manufacturing, allow the production of parts with complex shapes. It is important to control the condition of such components throughout their lifetime. The purpose of this article was to determine the basic acoustic properties of Ti6Al4V material produced by two different methods—bar drawing and the additive manufacturing method. On this basis, an inspection scheme was developed for adhesive joints, the components of which are made by additive manufacturing technology. The decibel drops in the amplitudes of pulses reflected from the boundary of the adhesive-Ti6Al4V-AM and adhesive-Ti6Al4V joints were determined. The decibel drops for the connection of materials made with additive technology are higher than for the material made in a conventional way. The difference in decibel drop in the amplitudes of the additive manufactured material versus the drawn rod, depending on the ultrasonic head, can be up to 60%. The results of the study provide an important practical guideline for testing adhesive joints of parts made with additive manufacturing technology.

A year after the first cases, the COVID-19 pandemic continued to put immense pressure on healthcare systems worldwide. With supply chains broken, the only opportunity for hospitals was to turn to unconventional solutions to overcome medical equipment shortages in the shortest possible time. This paper describes the methodology that allows the preparation of medical equipment to be additionally manufactured in keeping with medical requirements. The proposed method focuses on cytotoxicity tests against HaCaT, L929, A549 cell lines, and the assessment of potential antimicrobial properties of materials. The application of the proposed method is shown by the example of an adapter that connects a full mask with widely available DAR filters. The prototyping and fabrication of adapters were conducted with the fused deposition modelling (FDM) and selective laser sintering (SLS) technologies. The adapters increased the number of masks available to medical personnel, and by the same token, ensured the continuity of their work.

The jet impingement phenomenon plays an important role among the heat transfer intensification methods. Very often its application and analyses refer to simple flat surfaces, while there is a lack of information in the literature for cases addressing curved surfaces. In the present work, the single jet impingement on the non-flat (concave and convex) surface is studied for a wide range of geometries, which originate from the mini-jet heat-exchanger design. The numerical simulations were performed by an advanced ζ-f turbulence model implemented in the open-source OpenFOAM (ESI-OpenCFD Ltd, Bracknell, United Kingdom) code. Noticeable differences in the phenomena occurring on the convex and concave surfaces were identified in the stagnation zone. Besides, the existence and location of the secondary peak in the Nusselt number distribution differed between the cases. These distributions were influenced by the shape of geometry, which determined flow characteristics and resulting heat transfer performance. The origins of these differences were looked at in the turbulence characteristics close to the impinged surface of the stagnations zone and its vicinity, where turbulence kinetic energy and enstrophy were analysed. It was stated that the differences are already noticeable for the single jet impingement case, but they might sum up when multiple jets are considered. Therefore, here presented results would be important for the analysis of the overall unit of mentioned mini-jets heat-exchanger.

One of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied, for example, in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to the origin of this impact are still unanswered. In general, the wall-jet interaction and the near-wall turbulence are supposed to be its main reason, but their accurate numerical analysis is still very challenging. The authors’ aim was to construct the numerical model which can represent the real phenomena with good or very good accuracy. Starting with an analysis of single jet and obtaining the agreement with experimental data, it will be possible to extend the model towards the whole minijets heat exchanger. The OpenFOAM software, Bracknell, UK was used for that purpose, with our own implementation of the ζ-f turbulence model. The most difficult area to model is the stagnation region, where the thermal effects are the most intensive and, at the same time, strongly affected by the conditions in the pipe/nozzle/orifice of various size (conventional, mini, micro), from which the jet is injected. In the following article, summary of authors’ findings, regarding significance of the velocity profile and turbulence intensity at the jet place of discharge are presented. In addition, qualitative analysis of the heat transfer enhancement is included, in relation to the inlet conditions. In the stagnation point, Nusselt number differences reached the 10%, while, in general, its discrepancy in relation to inlet conditions was up to 23%.

Agriculture can provide biomass for bioproducts, biofuels and as energy feedstock with a low environmental impact, derived from carbohydrate, protein and oil annual crops, as well from lignocellulosic crops. This paper presents the thermophysical and chemical features of camelina and crambe straw depending on nitrogen fertilisation rate with a view to their further use in a circular bioeconomy. A two-factorial field experiment was set up in 2016, with camelina and crambe as the first factor and the N fertilizer rate (0, 60 and 120 kg·ha−1·N) as the second factor. Ash content in crambe straw (6.97% d.m.) was significantly higher than in camelina straw (4.79% d.m.). The higher heating value was higher for the camelina (18.50 MJ·kg−1·d.m.) than for the crambe straw (17.94 MJ·kg−1·d.m.). Sulphur content was also significantly higher in camelina than in crambe straw. An increase in nitrogen content with increasing fertilisation rate was visible in the straw of both species (from 1.19 to 1.33% d.m., for no fertilisation and for a rate of 120 kg·ha−1·N, respectively). Crambe straw contained more than five times more chlorine than camelina straw. In conclusion, despite certain adverse properties, camelina and crambe straw can be an alternative to other types of biomass, both for direct combustion, gasification and in the production of second-generation biofuels.