Search

The safety of airport runways is important to guarantee aircraft taking-off, landing, and taxiing, and the comparison of the mechanical response of pavement structures under dynamic and static loading by LS-DYNA has rarely been studied. The purpose of this work is to separate two analysis methods to investigate the mechanical response of rigid airport pavements. Firstly, a tire–road coupling model of an airfield was established to evaluate the suitability of dynamic and static analyses. Then, the effects of landing pitch angles, sinking speeds, and tire pressures on the effective stress, effective strain, and z-displacement of the runway were investigated for both dynamic and static analysis. Finally, the significance of influence factors was analyzed by regression analysis in Statistical Product and Service Solutions (SPSS). The results indicated that the effective stress, effective strain, and z-displacement of the runway increased with a decrease in the landing pitch angle, which also increased with an increase in the sinking speed and tire pressure. It was demonstrated that the difference in pavement mechanical response between dynamic and static analyses progressively widened at high tire pressure and sinking speed. In other words, the static analysis method can be adopted to assess the dynamic mechanical behavior when the landing pitch angle is large and the tire pressure is small. Among the various factors of mechanical response, the effect of tire pressure was the most obvious, followed by sinking speed and landing pitch angle. The work proposes a new approach to understanding the mechanical behavior of runways under complicated and varied conditions, evaluates the applicability of the dynamic and static mechanical analysis methods, identifies key factors in the dynamic and static mechanical analysis of rigid runways, and provides technical support for improving and maintaining the impact resistance of pavement facilities.

The geochemical characteristics of a 2.1 m BBW25 core, collected from the Beibu Gulf, have been investigated in terms of the major and trace elements, organic matter, and CaCO3 and AMS 14C dating by XRF, ICP-OES, ICP-MS, and more. We have found through previous research that there are issues with unclear delineation of sedimentary evolution environments and inexact responses between chemical weathering intensity and major paleoclimate events in the Beibu Gulf. The AMS 14C dating results indicate that the sedimentary age at the bottom was 19.24 ky b.p. CaCO3, δ13C, C/N, and Sr/Ba indexes show a sedimentary environment change from terrestrial to marine environments and a “jump” of ~4000 years in continent–ocean changes. The evolution of the sedimentary environment of Beibu Gulf was divided into three environments and five sub-environments. The changes in chemical weathering intensity indicators recorded by the CIX and the Fe/Al ratio respond well to the East Asian monsoon cycle, the meltwater events, and the alternation of cold and warm events. This study explains the chemical weathering intensity and sedimentary environment in the BBW25 core by geochemical characteristics and further reveals the paleoenvironmental characteristics and possible driving mechanisms over the past ~20,000 years.

A series of impact fuel tank experiments are carried out through the ballistic impact method. The ignition abilities of Bi2O3-reinforced PTFE/Al reactive material, metal aluminum, and inert metal steel are compared and analyzed, and the ignition mode of kerosene is explored when PTFE/Al/Bi2O3 impacts the fuel tank at different velocities. The results offer that PTFE/Al/Bi2O3 reactive material has outstanding ignition ability, and the order for ignition ability is PTFE/Al/Bi2O3 reactive material, metal aluminum, and inert metal steel. The kerosene content of the fuel tank has a significant impact on the ignition effect. The ignition effect of PTFE/Al/Bi2O3 reactive material impacting the fuel tank filled with 50% kerosene is weaker than that impacting the full tank. Under different impact velocities, PTFE/Al/Bi2O3 reactive materials display diverse ignition modes for kerosene: kerosene is directly ignited by the flame in the reverse reaction zone under low-velocity conditions, while high-temperature-activated reactive fragments are the ignition heat source of high-velocity conditions.

The conservation of morphology has resulted in considerable issues in the taxonomy of small mammals, especially for the identification of sibling species. Moreover, it is often difficult to completely solve such taxonomic problems by relying only on a single research method. The genus Crocidura is one of the genera with a conservative morphology and high species diversity. Among them, Crocidura attenuata has been considered in the field as the most widely distributed and common species. In fact, it is a species complex containing multiple species, and the classification and distribution of this species is controversial. In this study, the species and distribution of the Crocidura attenuata species complex experienced an integrated revision using three different levels of research methods: molecular, karyotype and morphology. The results show that (1) the C. attenuata species complex contains four known species (C. attenuata, C. tanakae, C. anhuiensis and C. dongyangjiangensis) and a cryptic species distributed in Guangxi, which may be the same undescribed species as the “C. attenuata” distributed in Vietnam. (2) C. attenuata is only distributed around the Sichuan Basin, C. tanakae is the most widely distributed throughout Southern China, and C. anhuiensis and C. dongyangjiangensis are almost sympatric in Southeast China. Furthermore, (3) although the molecular method lacks a unified threshold for species classification, it can rapidly and effectively identify the species of the C. attenuata species complex. Although karyotype and morphology methods cannot completely solve the species classification issues in respect of the C. attenuata species complex, they can provide supplemental information for taxonomic purposes. Therefore, the integrated taxonomic method can present the advantages of different methodological levels, and will provide further evidence for the taxonomy of sibling species with a conservative morphology.

The effect of a macromolecular additive on the etching rate of aluminum (Al) horizontal etching in the wet process was investigated in this work. The horizontal etching in the Al wet etching process became more evident as the film Al becomes thicker. The proposed macromolecule additive, including polyethylene-polypropylene glycol, was added into the Al etchant solution to reduce the Al horizontal etching rate (ER). The undercut problem during metal patterning can then be improved. By using this method, the Al horizontal ER was reduced from 2.0 to 0.9 μm per minute and the selection ratio between the horizontal and vertical ER was effectively improved from 3 to 1.3 times. As well, a hypothesis of physical mechanism for the improvement was proposed. The dispersed particles from the additive emulsion inhibited the transport and exchange of liquid in a horizontal direction. This work provides an alternative reference to improve the selection ratio performance in the metal wet etching process compared with that when using traditional method.

Remote sensing images have been widely applied in various industries; nevertheless, the resolution of such images is relatively low. Panchromatic sharpening (pan-sharpening) is a research focus in the image fusion domain of remote sensing. Pan-sharpening is used to generate high-resolution multispectral (HRMS) images making full use of low-resolution multispectral (LRMS) images and panchromatic (PAN) images. Traditional pan-sharpening has the problems of spectral distortion, ringing effect, and low resolution. The convolutional neural network (CNN) is gradually applied to pan-sharpening. Aiming at the aforementioned problems, we propose a distributed fusion framework based on residual CNN (RCNN), namely, RDFNet, which realizes the data fusion of three channels. It can make the most of the spectral information and spatial information of LRMS and PAN images. The proposed fusion network employs a distributed fusion architecture to make the best of the fusion outcome of the previous step in the fusion channel, so that the subsequent fusion acquires much more spectral and spatial information. Moreover, two feature extraction channels are used to extract the features of MS and PAN images respectively, using the residual module, and features of different scales are used for the fusion channel. In this way, spectral distortion and spatial information loss are reduced. Employing data from four different satellites to compare the proposed RDFNet, the results of the experiment show that the proposed RDFNet has superior performance in improving spatial resolution and preserving spectral information, and has good robustness and generalization in improving the fusion quality.

Mitochondrial DNA (mtDNA), coupled with maternal inheritance and relatively high mutation rates, provides a pivotal way for us to investigate the formation histories of populations. The Hui minority with Islamic faith is one of the most widely distributed ethnic groups in China. However, the exploration of Hui’s genetic architecture from the complete mitochondrial genome perspective has not been detected yet. Therefore, in this study, we employed the complete mitochondrial genomes of 98 healthy and unrelated individuals from Northwest China, as well as 99 previously published populations containing 7274 individuals from all over the world as reference data, to comprehensively dissect the matrilineal landscape of Hui group. Our results demonstrated that Hui group exhibited closer genetic relationships with Chinese Han populations from different regions, which was largely attributable to the widespread of haplogroups D4, D5, M7, B4, and F1 in these populations. The demographic expansion of Hui group might occur during the Late Pleistocene. Finally, we also found that Hui group might have gene exchanges with Uygur, Tibetan, and Tajik groups in different degrees and retain minor genetic imprint of European-specific lineages, therefore, hinting the existence of multi-ethnic integration events in shaping the genetic landscape of Chinese Hui group.

With regards to the electromagnetic measurement while drilling (EM-MWD), the extremely-low frequency electromagnetic wave signal (ELF-EM) below 20 Hz is usually used as the carrier of downhole measurement data due to the transmission characteristics of the electromagnetic wave (EM). However, influenced by the low frequency noise of drilling, the ELF-EM signal will be inevitably interfered by field noise, which ultimately impedes decoding. The Fourier band-pass filter can effectively remove out-of-band noise but is incapable of handling in-band noise. Therefore, based on the traditional method, a hybrid algorithm of adaptive Wiener algorithm and correlation detection (AWCD) is designed, so as to enhance the in-band noise processing capability, and the effectiveness of such algorithm is well verified through coding and decoding simulation as well as experimental data. The proposed algorithm, as indicated by theoretical analysis and test data, can effectively solve actual engineering issues, providing methodological references to engineers and technicians.

When the Al/Ta/PTFE reactive material was sintered at 360 °C in a vacuum sintering furnace, it was found that the material reacted to form a soft fluffy white substance and carbon black. To explore the reaction process further, powder samples of pure PTFE, Al/PTFE, Ta/PTFE and Al/Ta/PTFE, and molded cylindrical specimens were prepared. A TG-DSC test was carried out on the thermal reaction of four reactive materials, and XRD phase analysis was conducted on the white product, formed by the sintering reaction and the residue of the TG-DSC test sample, based on which of the pyrolysis processes and reaction mechanisms were analyzed. The results show that Ta and PTFE could have a chemical reaction at sintering temperature (360 °C) to form soft and fluffy white material TaF3 and carbon black, which can overflow the surface of the specimen and cause cracking of the specimen, which is tightly pressed. Since no obvious exothermic peak showed up on the TG-DSC curve, the composition of the residue of TG-DSC sample at different temperatures was tested and TaF3 was detected in the residue at 350 °C and 360 °C, indicating that Ta began to react with PTFE at a temperature range of 340−350 °C. According to the chemical properties and product formation of Ta, it could be speculated that the reaction mechanism between Ta and PTFE involves the PTFE decomposing first, then the fluorine-containing gas product reacting with metal Ta. According to the temperature range of the reaction, it is estimated that PTFE starts to decompose before 500 °C, but it is not detected effectively by TG-DSC, and the introduction of Ta could also affect the decomposition process of PTFE.

To analyze the mechanical properties and reaction characteristics of Al-ZrH2-PTFE (aluminum-zirconium hydride-polytetrafluoroethylene) composites under quasi-static compression, five types of specimens with different ZrH2 contents (0%, 5%, 10%, 20% and 30%) were prepared by molding-vacuum sintering. The true stress-strain curves and reaction rates of the different specimens were measured using quasi-static compression. The specific reaction processes were recorded by a high-speed camera. The corresponding reaction products were characterized by the XRD phase analysis, the calorific value was tested by a Calorimeter, and the reaction mechanism was analyzed. According to the results, the strength of the composites increased first and then decreased with the increase in the content of ZrH2. It reached a maximum of 101.01 MPa at 5%. Violent reaction occurred, and special flames were observed during the reaction of the specimens with 5% ZrH2. With the increase in the content of ZrH2, the chemical reaction was hard to induce due to the reduction in strength and toughness of composites. The reaction mechanism of Al/ZrH2/PTFE reveals that high temperatures at crack tip induced the reaction of Al and PTFE. Subsequently, ZrH2 decomposed to release hydrogen and generate ZrC. Calorimetric experiment shows that the calorific value of Al/ZrH2/PTFE with 20% ZrH2 is higher than that of Al/PTFE. The findings verify the potential of ZrH2 as an energetic additive for the enhancement of strength and release of the energy of the composites.

To better understand the thermal decomposition and reaction process of a fluorine-containing powdery thermite, PTFE/Al/MnO2, reactions at different temperatures were investigated by the TG/DSC-MS technique. The corresponding reaction products were characterized with XRD phase analysis. Another three thermite materials, i.e., PTFE/Al, Al/MnO2, and PTFE/MnO2, were also prepared for comparison. Results showed that PTFE behaved as both oxidizer and reducer in PTFE/Al/MnO2 fluorinated thermite. The thermal decomposition and reaction process of as-fabricated ternary thermite could be divided into two stages—the mutual reaction between each of PTFE, Al, and MnO2 and the subsequent reaction produced between Al and Mn2O3/Mn3O4/MnF2. Compared with the three control systems, the specially designed ternary system possessed a shorter reaction time, a faster energy release rate, and a better heat release performance.

Demand response (DR) has become an effective and critical method for obtaining better savings on energy consumption and cost. Buildings are the potential demand response resource since they contribute nearly 50% of the electricity usage. Currently, more DR applications for buildings were rule-based or utilized a simplified physical model. These methods may not fully embody the interaction among various features in the building. Based on the tree model, this paper presents a novel model based control with a random forest (MBCRF) learning algorithm for the demand response of commercial buildings. The baseline load of demand response and optimal control strategies are solved to respond to the DR request signals during peak load periods. Energy cost saving of the building is achieved and occupant’s thermal comfort is guaranteed simultaneously. A linguistic if-then rules-based optimal feature selection framework is also utilized to redefine the training and test set. Numerical testing results of the Pennsylvania-Jersey-Maryland (PJM) electricity market and Research and Support Facility (RSF) building show that the load forecasting error is as low as 1.28%. The peak load reduction is up to 40 kW, which achieves a 15% curtailment and outperforms rule-based DR by 5.6%.

As a novel energetic material with quite a high energy density, titanium hydride (TiH2) was introduced into a polytetrafluoroethylene/aluminum (PTFE/Al) reactive material system for the first time. The effects of TiH2 on the reaction energy, dynamic mechanical responses, and reaction properties of the composites were investigated through adiabatic bomb calorimeter, split-Hopkinson pressure bar, and drop-weight experiments. The results show that the reaction heat of the composites improved significantly as the content of TiH2 increased. Under dynamic compression, these composites show obvious strain hardening and strain rate hardening effects. Besides, a certain amount of TiH2 granules helps to improve the material’s compressive strength, and the maximum would even reach 173.2 MPa with 5% TiH2 percentage, 10.1% higher than that of PTFE/Al. Mesoscale images of the samples after dynamic compression indicate that interface debonding between the particles and PTFE matrix and the fracture of the PTFE matrix are the two major mechanisms resulting in the material’s failure. In addition, the drop-weight experiments indicate that the material’s impact sensitivities are sensitive to the content of TiH2, which would be increased to within 20% of the content of TiH2 compared with PTFE/Al, and the reaction degree is also improved to within 10% of the content of TiH2. The retrieved reaction residues after drop-weight experiments imply that the reaction is initiated at the edges of the samples, indicating a shear-induced initiation mechanism of this kind of reactive material.

Al-PTFE (aluminum-polytetrafluoroethene) is regarded as one of the most promising reactive materials (RMs). In this work, Ni (Nickel) was added to Al-PTFE composites for the purpose of improving the energy density and damage effect. To investigate the thermal behavior, mechanical properties and reaction characteristics of the Al-Ni-PTFE composites, an Al-PTFE mixture and an Al-Ni mixture were prepared by ultrasonic mixing. Six types of Al-Ni-PTFE specimens with different component mass ratios were prepared by molding sintering. Simultaneous thermal analysis experiments were carried out to characterize the thermal behavior of the Al-PTFE mixture and the Al-Ni mixture. Quasi-static compression tests were performed to analyze the mechanical properties and reaction characteristics of the Al-Ni-PTFE specimens. The results indicate that the reaction onset temperature of Al-Ni (582.7 °C) was similar to that of Al-PTFE (587.6 °C) and that the reaction heat of Al-Ni (991.9 J/g) was 12.5 times higher than that of Al-PTFE (79.6 J/g). With the increase of Ni content, the material changed from ductile to brittle and the strain hardening modulus and compressive strength rose first and then subsequently decreased, reaching a maximum of 51.35 MPa and 111.41 MPa respectively when the volume fraction of Ni was 10%. An exothermic reaction occurred for the specimens with a Ni volume fraction no more than 10% under quasi-static compression, accompanied by the formation of Ni-Al intermetallic compounds. In the Al-Ni-PTFE system, the reaction between Al and PTFE preceded the reaction between Al and Ni and the feasibility of increasing the energy density and damage effect of the Al-Ni-PTFE reactive material by means of Ni-Al reaction was proved.

Polytetrafluoroethylene/aluminum/molybdenum oxide (PTFE/Al/MoO3) reactive composites of a volume ratio of 60:16:24 were studied in this research. Quasi-static compression, dynamic compression and drop-weight experiments were performed to explore the mechanical response and the shear-induced initiation properties of the composites. Mesoscale images of the specimens after sintering demonstrate that PTFE, Al and MoO3 powders were evenly mixed and no chemical reaction occurred after the materials were stirred, pressed and sintered. The yield stress and compressive strength of PTFE/Al/MoO3 specimens are sensitive to strain rate within the range of 10−3~3 × 103 s−1, and the yield stress shows a bilinear dependence on the logarithm values of strain rate. The established Johnson-Cook constitutive model based on the experimental data can describe the mechanical response of PTFE/Al/MoO3 material well. Drop-weight tests show that the PTFE/Al/MoO3 specimens can react violently when impacted, with the characteristic drop height (H50) calculated as 51.57 cm. The recovered specimens show that the reaction started from the outer edge of the specimen with the largest shear force and the most concentrated shear deformation, indicating a shear-induced initiation mechanism. The reaction products of PTFE/Al/MoO3 specimens were AlF3, Al2O3, Mo and C, demonstrating that redox reaction occurred between PTFE and Al, and between Al and MoO3.

Implementing compact, efficient, and reliable passive pulsed lasers at visible wavelengths is attractive. This paper systematically investigated the thickness-dependent optical absorption characteristics of two-dimensional materials, including graphene, transition-metal dichalcogenides, and dye films at the 532 nm wavelength band, and revealed the effects of thickness on different optical absorption parameters. The results suggested that dye films are more suitable for loss-sensitive pulsed lasers and graphene is more suitable for modulation depth-sensitive pulsed lasers, while transition-metal dichalcogenide samples have intermediate performance. It can provide guidance for the rational selection of saturable absorbers in pulsed all-fiber lasers to optimize the optical pulse performance in the visible-wavelength band.

3-Methylthio-1-propanol (3-Met) is widely used as a flavoring substance and an essential aroma ingredient in many foods. Producing 3-Met by microbial transformation is green and eco-friendly. In the present study, one strain, YHM-G, which produced a high level of 3-Met, was isolated from the Baijiu-producing environment. Strain YHM-G was identified as Hyphopichia burtonii according to its morphological properties, physiological and biochemical characteristics, and ribosomal large subunit 26S rRNA gene D1/D2 domain sequence analysis. The optimal conditions for 3-Met production by YHM-G were obtained by single factor design, Plackett–Burman design, steepest ascent path design and response surface methodology as follows: 42.7 g/L glucose, pH 6, 0.9 g/L yeast extract, 6 g/L L-methionine (L-Met), culture temperature 28 °C, shaking speed 210 rpm, loading volume 50 mL/250 mL, inoculum size 0.5% (v/v), culturing period 48 h and 2.5 g/L Tween-80. Under these optimal conditions, the 3-Met production by strain YHM-G was 3.16 g/L, a value 88.1% higher than that before optimization. Strain YHM-G can also produce a variety of flavor compounds that are important for many foods. This strain thus has the potential to increase the abundance of 3-Met in some fermented foods and enhance their aroma profiles.

Chinese spiritual traditions such as Buddhism, Confucianism, and Taoism all emphasize the cultivation of idealistic mentalities (IMs) which are (1) not yet achieved, (2) clear in value judgment, (3) systematic and stable, and (4) cultivated with systematic training. While IMs are of interest to positive psychology, the methodology of positive psychology limits research on IMs. Fundamentally, positive psychology focuses on widely existing positive concepts and emphasizes being value-free, which conflicts with the features of IMs. Positive psychological studies relevant to IMs also suffer from methodological limitations: (1) recruiting samples without a spiritual background (realistic assumption); (2) ignoring qualitative differences between levels of actualization of IMs (linear assumption); (3) dividing systematic mental patterns into separate elements (reductionism); and (4) lacking value clarification during interventions. In summary, this article illustrates the methodological limitations of positive psychology in research on IMs. It encourages further research on IMs and supports the necessity of developing a new idealistic psychology for better research on IMs.

(1) Background: The widely developed thrust structures in the Jingzhushan Formation of late Cretaceous in Nyima Basin are related to the collision which leads to orogeny between the Lhasa and Qiangtang blocks. Clarifying the tectonic properties of the Nyima Basin is of great significance to characterize the evolution of the collision between the Lhasa block and the Qiangtang block. (2) Methods: Combined with mineralogy and petrology and U-Pb zircon dating of extrusive rocks, a detailed magnetic fabric test and rock magnetic experiment were carried out on the red sandstones of the Late Cretaceous Jingzhushan Formation in Nyima Basin. (3) Results: The sedimentary magnetic fabrics developed at the three sampling locations in the southern part of the basin are related to paleocurrents. The strained magnetic fabrics developed at one sampling site in the north, including pencil-like fabrics and tensile linear fabrics, are related to SE-NW tectonic stress. The average magnetic susceptibility value of the strained fabric with sandstone is lower than that of the sedimentary fabric, and its size is controlled by mica paramagnetic minerals. Ferromagnetic minerals are magnetite or hematite. In addition, the age of sandstone in the Jingzhushan Formation from the Nyima Basin matches the age of the eruptive rock in the Jingzhushan Formation from Coqen Basin, which is 92 Ma. (4) Conclusions: The strained fabric is developed near the thrust fault, which can explain the widely developed thrust structures in the basin. The Nyima Basin of the Jingzhushan Formation in the Late Cretaceous was an ocean-continent transitional foreland basin developed under the background of arc-arc “soft collision”.

Landfast ice plays an important role in the nearshore hydrodynamics of large lakes, such as the dampening of surface waves and currents. In this study, previously developed landfast ice basal stress parameterizations were added to an unstructured grid hydrodynamic ice model to represent the effects of grounded ice keels and tensile strength of ice cover. Numerical experiments using this model were conducted to evaluate the development of coastal landfast ice in Lake Superior. A sensitivity study of the free parameters was conducted from December 2018 to May 2021 to cover both high and low ice cover winters in Lake Superior and was compared against observations from the United States National Ice Center. The model reproduces the annual variation in coastal landfast ice in Lake Superior, particularly in shallow nearshore areas and the semi-enclosed bays in the northern regions of the lake. Experiments also show that the growth of landfast ice is mainly controlled by the free parameter that controls the critical ice thickness for the activation of basal stress. Overall, the model tends to underestimate the extent of coastal landfast against observations.