Search

Exposure to ceramic powders, which is frequent during handling operations, is known to cause adverse health effects. Finding proxy parameters to quantify exposure is useful for efficient and timely exposure assessments. Worker exposure during handling of five materials [a silica sand (SI1), three quartzes (Q1, Q2, and Q3), and a kaolin (K1)] with different particle shape (prismatic and platy) and sizes (3.4-120 µm) was assessed. Materials handling was simulated using a dry pendular mill under two different energy settings (low and high). Three repetitions of two kilos of material were carried out per material and energy conditions with a flow rate of 8-11 kg h-1. The performance of the dustiness index as a predictor of worker exposure was evaluated correlating material's dustiness indexes (with rotating drum and continuous drop) with exposure concentrations. Significant impacts on worker exposure in terms of inhalable and respirable mass fractions were detected for all materials. Mean inhalable mass concentrations during background were always lower than 40 µg m-3 whereas during material handling under high energy settings mean concentrations were 187, 373, 243, 156, and 430 µg m-3 for SI1, Q1, Q2, Q3, and K1, respectively. Impacts were not significant with regard to particle number concentration: background particle number concentrations ranged between 10 620 and 46 421 cm-3 while during handling under high energy settings they were 20 880 - 40 498 cm-3. Mean lung deposited surface area during background ranged between 27 and 101 μm2 cm-3 whereas it ranged between 22 and 42 μm2 cm-3 during materials handling. TEM images evidenced the presence of nanoparticles (≤100 nm) in the form of aggregates (300 nm-1 µm) in the worker area, and a slight reduction on mean particle size during handling was detected. Dustiness and exposure concentrations showed a high degree of correlation (R2 = 0.77-0.97) for the materials and operating conditions assessed, suggesting that dustiness could be considered a relevant predictor for workplace exposure. Nevertheless, the relationship between dustiness and exposure is complex and should be assessed for each process, taking into account not only material behaviour but also energy settings and workplace characteristics.

Five different portable instrument types to monitor exposure to nanoparticles were subject to an intensive intercomparison measurement campaign. Four of them were based on electrical diffusion charging to determine the number concentration or lung deposited surface area (LDSA) concentration of airborne particles. Three out of these four also determined the mean particle size. The fifth instrument type was a handheld condensation particle counter (CPC). The instruments were challenged with three different log-normally distributed test aerosols with modal diameters between 30 and 180 nm, varying in particle concentration and morphology. The CPCs showed the highest comparability with deviations on the order of only ±5%, independent of the particle sizes, but with a strictly limited upper number concentration. The diffusion charger-based instruments showed comparability on the order of ±30% for number concentration, LDSA concentration, and mean particle size, when the specified particle size range of the instruments matched the size range of the aerosol particles, whereas significant deviations were found when a large amount of particles exceeded the upper or lower detection limit. In one case the reported number concentration was even increased by a factor of 6.9 when the modal diameter of the test aerosol exceeded the specified upper limit of the instrument. A general dependence of the measurement accuracy of all devices on particle morphology was not detected.

In China, dust samplers were originally designed to collect 'total dust' for a short term during production, which is different from the widely adopted sampling strategy for dust. With the aim to provide the conversion factor from Chinese total dust to US and German respirable dust and to look at the influences on conversion factors from environment, production, and instruments, a comparative field study on the dust concentration measurements by different sampling methods was carried out in the same Chinese industries as in the 1989-1990 study and in some other factories. A supplemental experiment was also conducted in a wind tunnel. Dust concentration was measured with a parallel sampling strategy by using the following samplers: 10-mm nylon cyclone for US respirable dust (AR), FSP-Berufsgenossenschaftliches Institut für Arbeitssicherheit (BIA) cyclone for German respirable dust (GR), and samplers for Chinese total dust (CT). Totally, 1434 samples were collected (269 AR, 198 GR, and 967 CT), from which 429 matched sample pairs (249 pairs of AR/CT, 180 GR/CT) were available to calculate conversion ratios. Industry- and job-based conversion factors are presented in this study. The conversion factor of AR/CT was 0.38 for tungsten mines, 0.19 for copper/iron mines, 0.65 for tin mines, and 0.20 for pottery industry, while the factor of GR/CT was 0.69 for tungsten, 0.37 for copper/iron, and 0.52 for pottery. In the job category, AR/CT factors varied from 0.16 to 0.96 and GR/CT from 0.12 to 0.72. For the industries studied in 1988-1989, the AR/CT and GR/CT factors were 0.29 and 0.45, respectively. Both factors were definitely influenced by production, CT dust concentration, sample gain, and variation of dust concentration. Moreover, the respirable dust concentration by FSP-BIA was significantly higher than that by 10-mm cyclones, 63.27-73.10% more as showed also by the wind tunnel experiment. Meanwhile, the GR/CT ratio was significantly larger than the AR/CT in every industry or job with only few exceptions. The GR/CT estimates should be considered as independent ones. Following these results, there is a need to use 'ideal samplers' (consistent with the internationally accepted respirable fraction) in practice and to assess the existent samplers in order to homogenize the exposure data situation.

Background: SYNERGY is a large pooled analysis of case-control studies on the joint effects of occupational carcinogens and smoking in the development of lung cancer. A quantitative job-exposure matrix (JEM) will be developed to assign exposures to five major lung carcinogens [asbestos, chromium, nickel, polycyclic aromatic hydrocarbons (PAH), and respirable crystalline silica (RCS)]. We assembled an exposure database, called ExpoSYN, to enable such a quantitative exposure assessment., Methods: Existing exposure databases were identified and European and Canadian research institutes were approached to identify pertinent exposure measurement data. Results of individual air measurements were entered anonymized according to a standardized protocol., Results: The ExpoSYN database currently includes 356 551 measurements from 19 countries. In total, 140 666 personal and 215 885 stationary data points were available. Measurements were distributed over the five agents as follows: RCS (42%), asbestos (20%), chromium (16%), nickel (15%), and PAH (7%). The measurement data cover the time period from 1951 to present. However, only a small portion of measurements (1.4%) were performed prior to 1975. The major contributing countries for personal measurements were Germany (32%), UK (22%), France (14%), and Norway and Canada (both 11%)., Conclusions: ExpoSYN is a unique occupational exposure database with measurements from 18 European countries and Canada covering a time period of >50 years. This database will be used to develop a country-, job-, and time period-specific quantitative JEM. This JEM will enable data-driven quantitative exposure assessment in a multinational pooled analysis of community-based lung cancer case-control studies.

A range of industrial minerals was tested using the rotating drum and the continuous drop methods, the two methods proposed by the published European standard EN 15051 [CEN. (2006) EN 15051 Workplace atmospheres-measurement of the dustiness of bulk materials-requirements and test methods. Brussels, Belgium: European Committee for Standardization], to evaluate and compare their dustiness. The assessment of bulk materials dustiness can help to develop less dusty products and to reduce dust exposure to the workers by improving the processing of minerals. The European standard EN 15051 (CEN, 2006) proposes a classification system that was developed with the intention to assist in the labelling of products in the future. This paper presents a comparison of both test methods in classifying industrial minerals. The correlation between the dustiness measured by the two methods for the inhalable and respirable fractions is given. The results show there is no unambiguous dependence of the dustiness on the grain size of an industrial mineral. Although dustiness can significantly be affected by product moisture, the influence of this parameter is not studied in detail as the industrial minerals were tested in the conditions they are sold, as the standard requires. Especially, the classification of substances with respect to different classes of dustiness was found to be problematic, as the two methods are by no means yielding identical classification groups for all the substances. In any use of the standard (EN 15051; CEN, 2006) for labelling purposes, a revision of the present classification system provided in the standard is required for industrial minerals.

A field study was conducted in two mines in order to determine the most suitable strategy for ambient exposure assessment in the framework of a European study aimed at validation of biological monitoring approaches for diesel exhaust (BIOMODEM). Exposure to dust and particle-associated 1-nitropyrene (1-NP) was studied in 20 miners of black coal by the long wall method (Czech Republic) and in 20 workers in oil shale mining by the room and pillar method (Estonia). The study in the oil shale mine was extended to include 100 workers in a second phase (main study). In each mine half of the study population worked underground as drivers of diesel-powered trains (black coal) and excavators (oil shale). The other half consisted of workers occupied in various non-diesel production assignments. Exposure to diesel exhaust was studied by measurement of inhalable and respirable dust at fixed locations and by personal air sampling of respirable dust. The ratio of geometric mean inhalable to respirable dust concentration was approximately two to one. The underground/surface ratio of respirable dust concentrations measured at fixed locations and in the breathing zones of the workers was 2-fold or greater. Respirable dust was 2- to 3-fold higher in the breathing zone than at fixed sampling locations. The 1-NP content in these dust fractions was determined by gas chromatography-mass spectrometry/mass spectrometry and ranged from 0.003 to 42.2 ng/m(3) in the breathing zones of the workers. In mine dust no 1-NP was detected. In both mines 1-NP was observed to be primarily associated with respirable particles. The 1-NP concentrations were also higher underground than on the surface (2- to 3-fold in the coal mine and 10-fold or more in the oil shale mine). Concentrations of 1-NP in the breathing zones were also higher than at fixed sites (2.5-fold in the coal mine and 10-fold in the oil shale mine). For individual exposure assessment personal air sampling is preferred over air sampling at fixed sites. This study also suggests that particle-associated 1-NP much better reflects the ambient exposure to diesel exhaust particles than dust concentrations. Therefore, measurement of particle-associated 1-NP is preferred over measurement of dust concentrations by gravimetry, when linking ambient exposure to biomonitoring outcomes such as protein and DNA adducts and excretion of urinary metabolites of genotoxic substances.