Search

Modifying natural polymers with silicones gives new possibilities for packaging products and waste management. In this study, the innovative papers produced were altered following the reaction of polysaccharides and organosilicon compounds. The susceptibility of the studied material to biodegradation caused by a brown-rot fungus was assessed. Strength properties by tensile strength and dynamic mechanical analysis and hydrophobic properties by water uptake test and water contact angle analysis were evaluated. Moreover, elemental analysis by ICP method was controlled. The durability against fungi and the hydrophobic properties were increased by the modification. The fungal decay resistance of the silanized paper was reduced by water storage, which allows for managing paper waste. Cellulose-based paper treated with starch-modified methyltrimethoxysilane showed potential as a packaging material due to its reduced water uptake. Possible application areas could be corrugated boxes, cellulose thermoformed products for electronics, and food packaging. However, the water-repellent effect is limited to short-term exposure in humid conditions., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Nanocellulose has achieved an inimitable place and value in nano-materials research sector. Promising and exclusive physical, chemical and biological properties of nanocellulose make it an attractive and ideal material for various high end-user applications. Conventionally, the base material for nanocellulose i.e. cellulose is being extracted from various lignocellulosic raw materials (like wood, agro-industrial-residues, etc.) using pulping followed by bleaching sequences. As an alternate to lignocellulosic raw materials, waste paper also showed potential as a competent raw material due to its abundant availability and high cellulosic content (60-70%) with comparatively less hemicelluloses (10-20%) and lignin (5-10%) without any harsh treatments. The production yields of nanocellulose were reported to vary from 1.5% to 64% depending upon the waste papers and treatments given. The diameters of these nanocelluloses were reported in the range of 2-100 nm and crystallinity range around 54-95%. Thermal degradation of waste paper nanocellulose was varied from 187 °C to 371 °C. Although these properties are comparable with the nanocellulose obtained from lignocellulosic raw materials, yet waste paper is an underutilized source for nanocellulose preparation due to its ordinary fate of recycling, dumping and incineration. In the sight of necessity and possibility of waste paper utilization, this article reviews the outcomes of research carried out for preparation of nanocellulose using waste paper as a source of cellulose. There is a need of sincere investigation to convert this valuable waste to wealth i.e. waste papers to nanocellulose, which will be helpful in solid waste management to protect environment in economical way., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

Each year millions of tons of agricultural wastes are produced, however, not well utilized in China. Considering the economic development and environmental protection, the valorization of these wastes is increasingly necessary and important. Here we used p-toluenesulfonic acid hydrolysis followed by mild disk grinding for on-farm valorization of wheat straw (WS) and their pulping solid residue (waste wheat straw, WWS) to produce lignocellulosic nanofibrils (LCNF). Alkaline peroxide post-treatment was further conducted to obtain purified lignocellulosic nanofibrils (P-LCNF) with lower lignin content and thinner diameters. The raw materials and resulting LCNF and P-LCNF were investigated in each process for their chemical component, crystal structure, morphology, and thermal properties. Interestingly, although WS fiber had higher lignin content than WWS fiber, the WS fiber with lower ash content resulted in LCNF and P-LCNF with smaller height and lower thermal stability, but higher crystallinity and higher specific surface area. Higher ash content in WWS fiber protected cellulose and lignin from depolymerization and degradation, respectively, which endowed LCNF and P-LCNF with entangled network structure. Overall, this study indicated that the low-temperature fractionation process on WS and WWS fibers could yield cellulose nanomaterials with potential value-added application and achieve the efficient utilization of agricultural wastes., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

The morphological properties of cellulose nanofibrils obtained from eucalyptus pulp fibres were assessed. Two samples were produced with the same chemical treatment (NaClO/NaBr/TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical) oxidation), but distinct mechanical treatment intensities during homogenization. It was shown that the nanofibrils production yield increases with the mechanical energy. The effect of mechanical treatment on the yield was confirmed by laser profilometry of air-dried nanocellulose films. However, no significant differences were detected regarding the nanofibrils width as measured by atomic force microscopy (AFM) of air-dried films. On the other hand, differences in size were found either by laser diffraction spectroscopy or by dynamic light scattering (DLS) of the cellulose nanofibrils suspensions as a consequence of the differences in the length distribution of both samples. The nanofibrils length of the more nanofibrillated sample was calculated based on the width measured by AFM and the hydrodynamic diameter obtained by DLS. A length value of ca. 600 nm was estimated. The DLS hydrodynamic diameter, as an equivalent spherical diameter, was used to estimate the nanofibrils length assuming a cylinder with the same volume and with the diameter (width) assessed by AFM. A simple method is thus proposed to evaluate the cellulose nanofibrils length combining microscopy and light scattering methods., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

In this study, the suitability of optical devices for quantification of the fibrillation degree of bleached microfibrillated cellulose (MFC) materials has been assessed. The techniques for optical assessment include optical scanner, UV-vis spectrophotometry, turbidity, quantification of the fiber fraction and a camera system for dynamic measurements. The results show that the assessed optical devices are most adequate for quantification of the light transmittance of bleached MFC materials. Such quantification yields an estimation of the fibrillation degree. Films made of poorly fibrillated materials are opaque, while films made of highly fibrillated materials containing a major fraction of nanofibrils are translucent, with light transmittance larger than 90%. Finally, the concept of using images acquired with a CCD camera system, for estimating the fibrillation degree in dynamic conditions was exemplified. Such systems are most interesting as this will widen the applicability of optical methods for quantification of fibrillation degree online in production lines, which is expected to appear in the years to come., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

The complementary capabilities of various characterisation methods for micro-structural assessment are demonstrated. The assessed structures were composed of unbleached microfibrillated cellulose (MFC) in combination with bleached and 2,2,6,6-tetramethylpiperidinyl-1-oxyl (TEMPO) pre-treated MFC materials. The biodegradable nano-composites were thus characterised in detail, including laser profilometry, scanning electron microscopy (SEM) in high and low vacuum modes, and field-emission SEM. The distribution of the unbleached MFC materials was assessed by staining the unbleached MFC with osmium tetroxide (OsO(4)), which reacts with C=C double bonds encountered in lignin. In addition, some properties of the MFC nano-composite films were tested, i.e. tensile properties, water wettability and oxygen permeability. In general, the group of characteristics of the nano-composite MFC films was better than the properties of the films made of the neat MFC qualities. This indicates that mixing complementary MFC qualities could give synergetic effects that are not exploited completely when using the MFC qualities separately. The study thus confirms the suitability of unbleached MFC materials as a component in multilayer structures, for example biodegradable packaging applications., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Novel lightweight composite foams based on recycled polypropylene reinforced with cellulosic fibres obtained from agricultural residues were prepared and characterized. These composites, initially prepared by melt-mixing recycled polypropylene with variable fibre concentrations (10-25 wt.%), were foamed by high-pressure CO(2) dissolution, a clean process which avoids the use of chemical blowing agents. With the aim of studying the influence of the fibre characteristics on the resultant foams, two chemical treatments were applied to the barley straw in order to increase the α-cellulose content of the fibres. The chemical composition, morphology and thermal stability of the fibres and composites were analyzed. Results indicate that fibre chemical treatment and later foaming of the composites resulted in foams with characteristic closed-cell microcellular structures, their specific storage modulus significantly increasing due to the higher stiffness of the fibres. The addition of the fibres also resulted in an increase in the glass transition temperature of PP in both the solid composites and more significantly in the foams., (Copyright © 2011 Elsevier Ltd. All rights reserved.)