Search

The tightening trend of regulations on the levels of admitted pollutant emissions has given a great spur to the research work in the field of combustion and after-treatment devices. Despite the improvements that can be applied to the development of the combustion process, pollutant emissions cannot be reduced to zero; for this reason, the aftertreatment system will become a key component in the path to achieving near-zero emission levels.This study focuses on the numerical analysis and optimization of different metallic substrates, specifically developed for three-way catalyst (TWC) and Diesel oxidation catalyst (DOC) applications, to improve their thermal efficiency by reducing radial thermal losses through the outer mantle. The optimization process relies on computational fluid dynamics (CFD) simulations supported by experimental measurements to validate the numerical models carried out under uncoated conditions, where chemical reactions do not occur. Full-scale three-dimensional, multi-region models precisely describe the flow and temperature distributions allowing the evaluation of heat fluxes with the surrounding environment.A test cycle was designed to replicate the typical warm-up of a catalyst followed by a drop in the gas temperature and then a drop in the mass flow, replicating the engine switch-off condition.Different canning solutions and insulation strategies were considered at both numerical and experimental levels, and the results were compared. This allowed the validation of the numerical approach and identification of the best solution in terms of heat loss reduction and response time to heat up.

Future stringent emission legislation will require high efficient catalytical systems. Along with engine out emission reduction and advanced wash coat solution the substrate technology will play a key role in order to keep system costs as low as possible. The development of metallic substrates over the past few years has shown that turbulent-like substrates increase specific catalytic efficiency. This has made it possible to enhance overall performance for a specific catalytic volume or reduce the volume while keeping catalytic efficiency constant. This paper focuses on the emission efficiency of standard, TS (Transversal Structure) and LS (Longitudinal Structure) metallic substrates. In a first measurement program, standard TS and LS substrates have been compared using a 150cc 4 Stroke engine in dynamic (ECE R40) conditions. In a second test standard and LS substrate have been tested. Both TS and LS technologies show advantage compared to standard technology but have different application fields: TS is a cost effective solution for next emission limits while LS is a possible solution for future stringent emission limits.

Modern Diesel Engines equipped with Common-Rail Direct Injection and EGR are characterized by an increasingly high combustion efficiency. Consequently the exhaust gas temperature, especially during a cold start, is significantly reduced compared to typical values measured in previous engine generations. This leads to a potential problem with CO emission limit compliance. The present paper deals with an experimental investigation of turbulent-flow metal substrates, carried out on a vehicle roller bench using a production 1.3 Liter diesel engine equipped passenger car. The tested metal supported catalysts proved to yield extremely high conversion rates both during cold start and in warm operation phase. The improved mass transfer efficiency of the advanced metal substrates is related on one hand to the optimized coating technology and, on the other hand, to the enhanced flow performance in the single converter channels which is caused by structured metal foils. Additionally different cost saving scenarios have been analyzed by means of both catalyst volume reduction and decreased PGM loading.

Future stringent emission levels for NOx and PM will lead to the introduction of innovative combustion processes for diesel engines, such as premixed combustion, with the results to enhance the engine out emission of HC and CO. Therefore very efficient oxidation catalyst will be needed to face this possible issue. This paper deals with the optimization of a EU IV exhaust system by means of innovative metal supported catalyst, as for example the Pre Turbo Catalyst and the Hybrid Catalyst in combination with dedicated catalyst coatings. Moreover a base study over the use of PMFilter Catalyst has been made, to show the efficiency of such a device with EU IV engine calibration. The second part of the paper deals with the turbulent like structured foils substrates to have an even more efficient diesel oxidation catalyst with very high volumetric efficiency.

Future emission legislation can be met through substantial improvement in the effectiveness of the exhaust gas after-treatment system, the engine and the engine management system. For the catalytic converter, differentiation is necessary between the cold start behavior and the effectiveness at operating temperature. To be catalytically effective, a converter must be heated by the exhaust gas up to its light-off temperature. The major influential parameter for the light-off still is the supply of heat from the exhaust gas. Modification of the cold start calibration of engine control such as spark retard or increased idle speed can increase the temperature level of the exhaust gas. One further possibility is represented by a reduction of the critical mass ahead of the catalyst (exhaust manifold and pipe). Nevertheless the best measure to obtain optimal cold start effectiveness still seems to be locating the converter close to the engine. Depending on the individual application, limited installation space may only be available. Therefore the design target is a low volume, high effective catalyst with optimized thermodynamic properties to obtain maximum advantage of the thermal energy coming from the exhaust gases. The present paper deals with the cold start of a generic test cycle that can be subdivided in different phases, each characterized by different design parameters of the converter that are to be specifically tailored in order to achieve the maximum possible overall efficiency for the whole test.

Modern Diesel Engines equipped with Common-Rail Direct Injection, EGR and optimized combustion technology have been proven to reduce dramatically engine raw emissions both in terms of Nox and Particulate Matter. As a matter of fact the recently introduced FIAT 1.3 JTD 4 Cylinder Engine achieves Euro 4 limits with aid of conventional 2-way oxidation catalyst. Nevertheless some special applications, such as platforms with relatively higher gross vehicle weight possibly yield to PM-related issues. The present paper deals with the development program carried out to design a cost effective aftertreatment solution in order to address particulate matter tailpipe emissions. The major constraint of this development program was the extremely challenging packaging conditions and the absolute demand to avoid any major impact on the system design. The flow-through metal supported PM Filter Catalyst has been extensively tested on the specific vehicle application with aid of roller bench setup. Partial engine load soot loading, continuous regeneration and long term soot trapping efficiency have been addressed during the present work.

The effects of the internal geometry of catalytic converter channels on flow characteristics; exhaust backpressure and overall conversion efficiency have been investigated by means of both numerical simulations and experimental investigations. The numerical work has been carried out by means of a micro scale numerical tool specifically tailored for flow characteristics within converter channels. The results are discussed with aid of flow distribution patterns within the single cell and backpressure figures along the catalyst channel.