Search

A thermal gravimetric analyzer analyzed the thermal adsorption properties of developed composites with the temperature range of 28°C–650°C at a 20°C/min constant heat flow rate. The epoxy hybrid composites were synthesized using natural jute/sisal fibre hybridized with the addition of synthetic E-glass fibres at 0-degree, 0/90-degree, and intralaminar orientations through the wet filament-winding process. The effects of orientations on tensile, flexural, and impact strengths of epoxy hybrid composites were studied using ASTM D3039, D790, and D6110. The evaluated results were compared, and the epoxy hybrid composite containing intralaminar orientations found better thermal stability with reduced weight loss at 650°C. Similarly, the test result for mechanical studies of the hybrid composite showed superior tensile, flexural, and impact strengths. The epoxy hybrid composite with intralaminar orientation was found to have a maximum tensile, impact, and flexural strength of 61.91 MPa, 770.61 J/m, and 83.90 MPa, respectively. [ABSTRACT FROM AUTHOR]

Advances in friction materials are imposed on developing multiceramic reinforced hybrid nanocomposites with superior tribomechanical properties. The silver-based matrix metals are gained significance in various applications like bearing, ratchet, and electrical contacts due to their high frictional resistance and good thermal and chemical stability compared to traditional metals. The present research is to develop silver-based hybrid nanocomposites containing alumina (Al2O3) and silicon carbide (SiC) nanoparticles of 50 nm mixing with the ratio of 0 wt% Al2O3/0 wt% SiC, 5 wt% Al2O3/0 wt% SiC, and 5 wt% Al2O3/5 wt% SiC via the semisolid vacuum stir-cast technique. The vacuum technology minimizes casting defects and increases composite properties. The casted composite samples are subjected to study the effect of reinforcement on thermal adsorption, conductivity, diffusivity, and frictional resistance. The composite containing 5 wt% Al2O3np/5 wt% SiCnp is to find optimum thermal and frictional behaviour. The thermal adsorption and frictional resistance are increased by 30% and 27% compared to unreinforced cast silver. The Ag/5 wt% Al2O3np/5 wt% SiCnp hybrid nanocomposite is recommended for automotive friction-bearing applications. [ABSTRACT FROM AUTHOR]

Inorganic-based ceramic reinforcements are promising superior thermal behaviour and are lightweight and developed with aluminium alloy matrix for automobile applications. The AA6061 alloy nanocomposite containing 0 wt%, 4 wt%, 8 wt%, and 12 wt% of silicon nitride nanoparticles(50 nm) was synthesized by stir cast. The influences of thermal adsorption on silicon nitride (nano) additions, density, thermal response, hardness, and wear characteristics of AA6061 matrix nanocomposites are studied. Based on the rule of mixture, the density of nanocomposites is evaluated. The differential thermal and thermogravimetric analysis techniques are used to find the thermal response nanocomposite. The differential scanning calorimeter is used to find the heat flow between 400°C and 700°C. The micro Vickers hardness and wear characteristics of AA6061 nanocomposite were experimentally investigated by ASTM E384 and ASTM G99-05 standards. The adsorption of inorganic nanosilicon nitride particles (12 wt%) in AA6061 alloy showed a decreased mass loss with increased temperatures 0° to 700°C. The differential thermal analysis of nanocomposite reveals the transformation of solid-to-liquid phase under high temperature (528°C). [ABSTRACT FROM AUTHOR]

In this study, the moisture and thermal transmission properties of cotton/polylactic acid-blended knitted fabrics were studied. Cotton and polylactic acid fibers were blended to produce yarns of 14.7 tex (40 s Ne) with two different blend proportions. The yarns were then knitted into plain jersey structures, followed by scouring and bleaching treatments. The produced fabrics were evaluated for dynamic moisture transport properties using SDL Atlas moisture management tester. The moisture vapor transmission rate of developed fabrics was measured using the dish method, and the thermal properties were measured using KES Thermolabo instrument. Results indicate that blending of polylactic acid fibers with cotton fibers improve the moisture management properties of the resultant fabric. The overall moisture management capability values were found to be better for cotton/polylactic acid fiber 65:35 blended fabric. A marginal improvement was observed only in the case of cotton/polylactic acid fiber 80:20 blended fabric. The moisture vapor transmission and air permeability of blended fabrics were also found to be higher than those of 100% cotton fabric. The thermal conductivity, insulation, and warm–cool feel values of blended fabrics range between 100% cotton and 100% polylactic acid fiber fabrics. This type of fabric is more suitable for use as sportswear and active wear. [ABSTRACT FROM AUTHOR]

The water vapor transport (WVT) through a set of cotton and polyester cotton fabrics has been analyzed under dynamic conditions using the CIRCOT WVTR Apparatus. The hygrograms obtained for cotton fabrics from the experiment show three distinct phases in water vapor transport rate (WVTR) with time, in which the first slower phase may be attributed to the moisture buffering by the fabric. In addition to the parameter T82.5% defined by earlier authors, five more parameters (α, β, R30, R90 and Tb) have been defined out of which β, R30 and Tb may be considered to represent moisture buffering in fabrics. In the case of P-C blended fabrics, the hygrogram was strongly influenced by the cotton content in the fabric apart from the parameters mentioned earlier. [ABSTRACT FROM AUTHOR]