Search

MagAO-X is an entirely new extreme adaptive optics system for the Magellan Clay 6.5 m telescope, funded by the NSF MRI program starting in Sep 2016. The key science goal of MagAO-X is high-contrast imaging of accreting protoplanets at Hα. With 2040 actuators operating at up to 3630 Hz, MagAO-X will deliver high Strehls (> 70%), high resolution (19 mas), and high contrast (< 1 × 10^(-4)) at Hα (656 nm). We present an overview of the MagAO-X system, review the system design, and discuss the current project status.

The low wind effect is a phenomenon disturbing the phase of the wavefront in the pupil of a large telescope obstructed by spiders, in the absence of wind. It can be explained by the radiative cooling of the spiders, creating air temperature inhomogeneities across the pupil. Because it is unseen by traditional adaptive optics (AO) systems, thus uncorrected, it significantly degrades the quality of AO-corrected images. We provide a statistical analysis of the strength of this effect as seen by VLT/SPHERE after 4 years of operations. We analyse its dependence upon the wind and temperature conditions. We describe the mitigation strategy implemented in 2017: a specific coating with low thermal emissivity in the mid-infrared was applied on the spiders of Unit Telescope 3. We quantify the improvement in terms of image quality, contrast and wave front error using both focal plane images and measured phase maps.

We are building a next-generation laser adaptive optics system, Robo-AO-2, for the UH 2.2-m telescope that will deliver robotic, diffraction-limited observations at visible and near-infrared wavelengths in unprecedented numbers. The superior Maunakea observing site, expanded spectral range and rapid response to high-priority events represent a significant advance over the prototype. Robo-AO-2 will include a new reconfigurable natural guide star sensor for exquisite wavefront correction on bright targets and the demonstration of potentially transformative hybrid AO techniques that promise to extend the faintness limit on current and future exoplanet adaptive optics systems.

The success of ground-based, high contrast imaging for the detection of exoplanets in part depends on the ability to differentiate between quasi-static speckles caused by aberrations not corrected by adaptive optics (AO) systems, known as non-common path aberrations (NCPAs), and the planet intensity signal. Frazin (ApJ, 2013) introduced a post-processing algorithm demonstrating that simultaneous millisecond exposures in the science camera and wavefront sensor (WFS) can be used with a statistical inference procedure to determine both the series expanded NCPA coefficients and the planetary signal. We demonstrate, via simulation, that using this algorithm in a closed-loop AO system, real-time estimation and correction of the quasi-static NCPA is possible without separate deformable mirror (DM) probes. Thus the use of this technique allows for the removal of the quasi-static speckles that can be mistaken for planetary signals without the need for new optical hardware, improving the efficiency of ground-based exoplanet detection. In our simulations, we explore the behavior of the Frazin Algorithm (FA) and the dependence of its convergence to an accurate estimate on factors such as Strehl ratio, NCPA strength, and number of algorithm search basis functions. We then apply this knowledge to simulate running the algorithm in real-time in a nearly ideal setting. We then discuss adaptations that can be made to the algorithm to improve its real-time performance, and show their efficacy in simulation. A final simulation tests the technique’s resilience against imperfect knowledge of the AO residual phase, motivating an analysis of the feasibility of using this technique in a real closed-loop Extreme AO system such as SCExAO or MagAO-X, in terms of computational complexity and the accuracy of the estimated quasi-static NCPA correction.

We report on initial results from the largest infrared AO direct imaging survey searching for wide orbit (≳ 100 AU) massive exoplanets and brown dwarfs as companions around young nearby stars using Robo-AO at the 2.1-m telescope on Kitt Peak, Arizona. The occurrence rates of these rare substellar companions are critical to furthering our understanding of the origin of planetary-mass companions on wide orbits. The observing efficiency of Robo-AO allows us to conduct a survey an order of magnitude larger than previously possible. We commissioned a low-noise high-speed SAPHIRA near-infrared camera to conduct this survey and report on its sensitivity, performance, and data reduction process.

The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument is an extremely modular high- contrast instrument installed on the Subaru telescope in Hawaii. SCExAO has a dual purpose. Its position in the northern hemisphere on a 8-meter telescope makes it a prime instrument for the detection and characterization of exoplanets and stellar environments over a large portion of the sky. In addition, SCExAO’s unique design makes it the ideal instrument to test innovative technologies and algorithms quickly in a laboratory setup and subsequently deploy them on-sky. SCExAO benefits from a first stage of wavefront correction with the facility adaptive optics AO188, and splits the 600-2400 nm spectrum towards a variety of modules, in visible and near infrared, optimized for a large range of science cases. The integral field spectrograph CHARIS, with its J, H or K-band high-resolution mode or its broadband low-resolution mode, makes SCExAO a prime instrument for exoplanet detection and characterization. Here we report on the recent developments and scientific results of the SCExAO instrument. Recent upgrades were performed on a number of modules, like the visible polarimetric module VAMPIRES, the high-performance infrared coronagraphs, various wavefront control algorithms, as well as the real-time controller of AO188. The newest addition is the 20k-pixel Microwave Kinetic Inductance Detector (MKIDS) Exoplanet Camera (MEC) that will allow for previously unexplored science and technology developments. MEC, coupled with novel photon-counting speckle control, brings SCExAO closer to the final design of future high-contrast instruments optimized for Giant Segmented Mirror Telescopes (GSMTs).

The Real-Time Controller (RTC) for the Thirty Meter Telescope (TMT) Narrow Field Infrared Adaptive Optics System (NFIRAOS) is the software and server hardware that converts wavefront error measurements into wavefront corrector demands, at the heart of the laser guide star multi-conjugate adaptive optics (MCAO) or natural guide star adaptive optics (NGS AO). The RTC takes input from up to six Shack-Hartmann Laser Guide Star wavefront sensors (LGS WFS), one high-order Natural Guide Star Pyramid Wavefront Sensor (PWFS), up to three Shack-Hartmann On-Instrument wavefront sensors (OIWFS) that are located in the client science instruments, and up to 4 on-detector guide windows (ODGW) also in the client instruments. The RTC controls two deformable mirrors conjugated to 0km (DM0) and 11.8km (DM11). DM0 is mounted on a tip/tilt stage (TTS). During the final design phase we performed prototyping to verify that off-the-shelf servers using general purpose CPUs are able to support the maximum 800 Hz frequency at which the RTC is required to operate. We also considered methods to provide live data streams to a graphical user interface without impacting the AO system performance. This paper will discusses the outcome of the impact of jitter and latency on loop speed in our prototype and an overview of the RTC pipeline, including the many “knobs” that can be turned to fine-tune the behavior of NFIRAOS in different observing modes, and under different observing conditions.

High-dispersion coronagraphy (HDC) combines high contrast imaging techniques with high spectral resolution spectroscopy to observe exoplanets and determine characteristics such as chemical composition, temperature, and rotational velocities. It has been demonstrated in lab that with monochromatic light, a fiber injection unit (FIU), in which an optical fiber is used to couple to light from the exoplanet, could be used to direct exoplanet light to a high-resolution spectrograph, with robust performance and speckle suppression that exceeds conventional image-based speckle nulling. We now demonstrate in lab a FIU based speckle nulling scheme with a Kalman filter estimator. We currently find that speckle nulling with a Kalman filter is more stable and outperforms traditional speckle nulling by 10% in suppression in the presence of white detector noise.

NFIRAOS (Narrow-Field InfraRed Adaptive Optics System) will be the first-light multi-conjugate adaptive optics system for the Thirty Meter Telescope (TMT). NFIRAOS houses all of its opto-mechanical sub-systems within an optics enclosure cooled to precisely -30°C in order to improve sensitivity in the near-infrared. It supports up to three client science instruments, including the first-light InfraRed Imaging Spectrograph (IRIS). Powering NFIRAOS is a Real Time Controller that will process the signals from six laser wavefront sensors, one natural guide star pyramid WFS, up to three low-order on-instrument WFS and up to four guide windows on the client instrument’s science detector in order to correct for atmospheric turbulence, windshake, optical errors and plate-scale distortion. NFIRAOS is currently preparing for its final design review in late June 2018 at NRC Herzberg in Victoria, British Columbia in partnership with Canadian industry and TMT.

A fiber injection unit situated in the focal plane behind a coronagraph feeding a high resolution spectrograph can be used to couple light from an exoplanet to obtain high resolution spectra with improved sensitivity. However, the signal-to-noise ratio of the planet signal is limited by the coupling of starlight into the single mode fiber. To minimize this coupling, we need to apply a control loop on the stellar wavefront at the input of the fiber. We present here a wavefront control algorithm based on the formalism of the Electric Field Conjugation (EFC) controller that accounts for the effect of the fiber. The control output is the overlap integral of the electric field with the fundamental mode of a single mode fiber. This overlap integral is estimated by sending probes to a deformable mirror. We present results from simulations, and laboratory results obtained at the Caltech Exoplanet Technology Lab’s transmissive testbed. We show that our approach offers a significant improvement in starlight suppression through the fiber relative to a conventional EFC controller. This new approach improves the contrast of a high contrast instrument and could be used in future missions.

Exoplanet imaging requires excellent wavefront correction and calibration. At the Subaru telescope this is achieved us- ing the 188-element facility adaptive optics system(AO188) feeding the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) instrument; a multipurpose instrument built to deliver high contrast images of planets and disks around nearby stars. AO188 offers coarse correction while SCExAO performs fine correction and calibration of 1000 modes. The full system achieves 90%Strehl Ratio in H-band and diffraction limited images. A new Real Time Computer allowing higher performance between SCExAO and AO188 is currently implemented. Future upgrades will include a new Pyramid Wavefront Sensor and (64x64) DM to achieve extreme AO correction inside AO188. We are progressing in the development of predictive control and sensor fusion algorithms across the system to improve performance and calibration. With the new upgrades, SCExAO will be able to image giant planets in reflected light with Subaru and validate technologies necessary to image habitable Earth-like planets with the Thirty Meter Telescope (TMT).

This paper discusses point spread function reconstruction (PSFR) simulations for laser guide star (LGS) multi-conjugate adaptive optics (MCAO) on extremely large telescopes (ELTs). The Multithreaded Adaptive Optics Simulator (MAOS), configured to simulate the Thirty Meter Telescope (TMT) Narrow Field InfraRed Adaptive Optics System (NFIRAOS), provided simulated telemetry. For median Mauna Kea turbulence conditions (0.55arcsec seeing) and for the expected NFRIAOS laser guide star (LGS) wavefront sensor (WFS) measurement noise, the actuator error based PSFR algorithm leads to Strehl Ratio (SR), enclosed energy (EE) and PSF profile errors below 8% in Z-band, 5% in J-band and 2% in Kband assuming perfect knowledge of the turbulence and wind profiles and of measurement noise. Further algorithm optimization could in principle reduce this residual error level.

For Extremely Large Telescope (ELT) adaptive optics (AO) systems, multiple Sodium Laser Guide Star (LGS) wavefront sensors (WFSs) are required to achieve high sky coverage and diffraction limited performance. However, temporal and spatial variation of the sodium profile causes measurement biases that appear at all time scales and vary between LGS WFSs. To make things worse, optical design residuals, polishing and alignment errors also create non-common-path aberrations (NCPA) that vary between sub-apertures and different WFS, causing LGS WFS to work significantly off null with a nonlinear response. The induced aberrations are consequently non-radially symmetric, even for center launch laser beams with polar coordinate detectors. Natural guide star (NGS) based truth wavefront sensors are often suggested as a method of sensing these LGS WFS aberrations, but a single sensor will suffer strong anisoplanatism that may introduce additional errors. In this paper, we present mitigation strategies and performance estimations based on simulations for the Thirty Meter Telescope (TMT) Narrow Field Infrared AO system (NFIRAOS).

The Magellan extreme adaptive optics (MagAO-X) instrument is a new extreme adaptive optics (ExAO) system designed for operation in the visible to near-IR which will deliver high contrast-imaging capabilities. The main AO system will be driven by a pyramid wavefront sensor (PyWFS); however, to mitigate the impact of quasi-static and non-common path (NCP) aberrations, focal plane wavefront sensing (FPWFS) in the form of low-order wavefront sensing (LOWFS) and spatial linear dark field control (LDFC) will be employed behind a vector apodizing phase plate (vAPP) coronagraph using rejected starlight at an intermediate focal plane. These techniques will allow for continuous high-contrast imaging performance at the raw contrast level delivered by the vAPP coronagraph 6 x 10^(-5). We present simulation results for LOWFS and spatial LDFC with a vAPP coronagraph, as well as laboratory results for both algorithms implemented with a vAPP coronagraph at the University of Arizona Extreme Wavefront Control Lab.

Spectroscopy of exoplanets can potentially detect biomarkers in habitable planets around other stars. The high dispersion coronagraphy (HDC) technique provides a pathway to search for biomarkers in planets around M dwarfs with next-generation ground-based extremely large telescopes (ELTs). The HDC consists of a coronagraph operating behind an extreme adaptive optics (AO) system, a single-mode fiber injection unit, and a high resolution spectrometer (HRS). The coronagraph spatially filters out starlight while the HRS spectrally discriminates starlight from planet light, reaching a starlight suppression level that enables biomarker detection. I will simulating ELT HDC instrument performance as a function of wavelength, spectral resolution, starlight suppression, and planet types, considering realistic noise budget that includes speckle noise, thermal and sky background and exozodical background.

Wavefront sensing in the infrared is highly desirable for the study of M-type stars and cool red objects, as they are sufficiently bright in the infrared to be used as the adaptive optics guide star. This aids in high contrast imaging, particularly for low mass stars where the star-to-planet brightness ratio is reduced. Here we discuss the combination of infrared detector technology with the highly sensitive Pyramid wavefront sensor (WFS) for a new generation of systems. Such sensors can extend the capabilities of current telescopes and meet the requirements for future instruments, such as those proposed for the giant segmented mirror telescopes. Here we introduce the infrared Pyramid WFS and discuss the advantages and challenges of this sensor. We present a new infrared Pyramid WFS for Keck, a key sub-system of the Keck Planet Imager and Characterizer (KPIC). The design, integration and testing is reported on, with a focus on the characterization of the SAPHIRA detector used to provide the H-band wavefront sensing. Initial results demonstrate a required effective read noise <1e^– at high gain.

The Rapid Transient Surveyor (RTS) is a proposed rapid-response, high-cadence adaptive optics (AO) facility for the UH 2.2-m telescope on Maunakea. RTS will uniquely address the need for high-acuity and sensitive near-infrared spectral follow-up observations of tens of thousands of objects in mere months by combining an excellent observing site, unmatched robotic observational efficiency, and an AO system that significantly increases both sensitivity and spatial resolving power. We will initially use RTS to obtain the infrared spectra of ∼4,000 Type Ia supernovae identified by the Asteroid Terrestrial-Impact Last Alert System over a two year period that will be crucial to precisely measuring distances and mapping the distribution of dark matter in the z < 0.1 universe. RTS will comprise an upgraded version of the Robo-AO laser AO system and will respond quickly to target-of-opportunity events, minimizing the time between discovery and characterization. RTS will acquire simultaneous-multicolor images with an acuity of 0.07–0.10" across the entire visible spectrum (20% i′-band Strehl in median conditions) and <0.16" in the near infrared, and will detect companions at 0.5" at contrast ratio of ∼500. The system will include a high-efficiency prism integral field unit spectrograph: R = 70-140 over a total bandpass of 840–1830nm with an 8.7" by 6.0" field of view (0.15" spaxels). The AO correction boosts the infrared point-source sensitivity of the spectrograph against the sky background by a factor of seven for faint targets, giving the UH 2.2-m the H-band sensitivity of a 5.7-m telescope without AO.

The Keck II Laser Guide Star (LGS) Adaptive Optics (AO) System was upgraded from a dye laser to a TOPTICA/MPBC Raman-Fibre Amplification (RFA) laser in December 2015. The W. M. Keck Observatory (WMKO) has been operating its AO system with a LGS for science since 2004 using a first generation 15 W dye laser. Using the latest diode pump laser technology, Raman amplification, and a well-tuned second harmonic generator (SHG), this Next Generation Laser (NGL) is able to produce a highly stable 589 nm laser beam with the required power, wavelength and mode quality. The beam’s linear polarization and continuous wave format along with optical back pumping are designed to improve the sodium atom coupling efficiency over previously operated sodium-wavelength lasers. The efficiency and operability of the new laser has also been improved by reducing its required input power and cooling, size, and the manpower to operate and maintain it. The new laser has been implemented on the telescope’s elevation ring with its electronics installed on a new Nasmyth sub-platform, with the capacity to support up to three laser systems for future upgrades. The laser is projected from behind the telescope’s secondary mirror using the recently implemented center launch system (CLS) to reduce LGS spot size. We will present the new laser system and its performance with respect to power, stability, wavelength, spot size, optical repumping, polarization, efficiency, and its return with respect to pointing alignment to the magnetic field. Preliminary LGSAO performance is presented with the system returning to science operations. We will also provide an update on current and future upgrades at the WMKO.

The direct detection of low-mass planets in the habitable zone of nearby stars is an important science case for future E-ELT instruments such as the mid-infrared imager and spectrograph METIS, which features vortex phase masks and apodizing phase plates (APP) in its baseline design. In this work, we present end-to-end performance simulations, using Fourier propagation, of several METIS coronagraphic modes, including focal-plane vortex phase masks and pupil-plane apodizing phase plates, for the centrally obscured, segmented E-ELT pupil. The atmosphere and the AO contributions are taken into account. Hybrid coronagraphs combining the advantages of vortex phase masks and APPs are considered to improve the METIS coronagraphic performance.

We discuss the advantages of wavefront sensing at near-infrared (IR) wavelengths with low-noise detector technologies that have recently become available. In this paper, we consider low order sensing with laser guide star (LGS) adaptive optics (AO) and high order sensing with natural guide star (NGS) AO. We then turn to the application of near-IR sensing with the W. M. Keck Observatory (WMKO) AO systems for science and as a demonstrator for similar systems on extremely large telescopes (ELTs). These demonstrations are based upon an LGS AO near-IR tip-tilt-focus sensor and our collaboration to implement a near-IR pyramid wavefront sensor (PWFS) for a NGS AO L-band coronagraphic imaging survey to identify exoplanet candidates.

General relativity can be tested in the strong gravity regime by monitoring stars orbiting the supermassive black hole at the Galactic Center with adaptive optics. However, the limiting source of uncertainty is the spatial PSF variability due to atmospheric anisoplanatism and instrumental aberrations. The Galactic Center Group at UCLA has completed a project developing algorithms to predict PSF variability for Keck AO images. We have created a new software package (AIROPA), based on modified versions of StarFinder and Arroyo, that takes atmospheric turbulence profiles, instrumental aberration maps, and images as inputs and delivers improved photometry and astrometry on crowded fields. This software package will be made publicly available soon.

The Laser Guide Star Facility (LGSF) is responsible for generating the artificial laser guide stars required by the TMT Laser Guide Star (LGS) AO systems. The LGSF uses multiple sodium lasers to generate and project several LGS asterisms from a laser launch telescope located behind the TMT secondary mirror. The LGSF includes 3 main subsystems: (1) the laser system, (2) the beam transfer optics (BTO) system, (3) the associated laser safety system. At present, the LGSF is in the preliminary design phase. During this phase, the laser launch telescope trade study, Beam transfer optical path trade study are compared carefully, and some critical components prototypes have been carried out to verify the requirements, such as the polarization status control and test, the Fast Steer Mirror (FSM) prototype test.

Prototyping and benchmarking was performed for the Real-Time Controller (RTC) of the Narrow Field InfraRed Adaptive Optics System (NFIRAOS). To perform wavefront correction, NFIRAOS utilizes two deformable mirrors (DM) and one tip/tilt stage (TTS). The RTC receives wavefront information from six Laser Guide Star (LGS) Shack- Hartmann WaveFront Sensors (WFS), one high-order Natural Guide Star Pyramid WaveFront Sensor (PWFS) and multiple low-order instrument detectors. The RTC uses this information to determine the commands to send to the wavefront correctors. NFIRAOS is the first light AO system for the Thirty Meter Telescope (TMT). The prototyping was performed using dual-socket high performance Linux servers with the real-time (PREEMPT_RT) patch and demonstrated the viability of a commercial off-the-shelf (COTS) hardware approach to large scale AO reconstruction. In particular, a large custom matrix vector multiplication (MVM) was benchmarked which met the required latency requirements. In addition all major inter-machine communication was verified to be adequate using 10Gb and 40Gb Ethernet. The results of this prototyping has enabled a CPU-based NFIRAOS RTC design to proceed with confidence and that COTS hardware can be used to meet the demanding performance requirements.

We have started an initial three-year deployment of Robo-AO at the 2.1-m telescope at Kitt Peak, Arizona as of November 2015. We report here on the project status and two new developments with the Robo-AO KP system: the commissioning of a sub-electron readnoise SAPHIRA near-infrared camera, which will allow us to widen the scope of possible targets to low-mass stellar and substellar objects; and, performance analysis and tuning of the adaptive optics system, which will improve the sensitivity to these objects. Commissioning of the near-infrared camera and optimizing the AO performance occur in parallel with ongoing visible-light science programs.

This paper presents the AO performance we got on-sky with RAVEN, a Multi-Object Adaptive Optics (MOAO) technical and science demonstrator installed and tested at the Subaru telescope. We report Ensquared-Energy (EE) and Full Width at Half Maximum (FWHM) measured from science images on Subaru's IRCS taken during all of the on-sky observing runs. We show these metrics as function of different AO modes and atmospheric conditions for two asterisms of natural guide stars. The performances of the MOAO and Ground-Layer AO (GLAO) modes are between the classical Single-Conjugate AO (SCAO) and seeing-limited modes. We achieve the EE of 30% in H-band with the MOAO correction, which is a science requirement for RAVEN. The MOAO provides sightly better performance than the GLAO mode in both asterisms. One of the reasons which cause this small difference between the MOAO and GLAO modes may be the strong GL contribution. Also, the performance of the MOAO modes is affected by the accuracy of the on-sky turbulence profiling by the SLOpe Detection And Ranging (SLODAR) method.

The Robo-AO Kepler Planetary Candidate Survey is observing every Kepler planet candidate host star (KOI) with laser adaptive optics imaging to hunt for blended nearby stars which may be physically associated companions. With the unparalleled efficiency provided by the first fully robotic adaptive optics system, we perform the critical search for nearby stars (0.15" to 4.0" separation with contrasts up to 6 magnitudes) that dilute the observed planetary transit signal, contributing to inaccurate planetary characteristics or astrophysical false positives. We present 3313 high resolution observations of Kepler planetary hosts from 2012-2015, discovering 479 nearby stars. We measure an overall nearby star probability rate of 14.5±0.8%. With this large data set, we are uniquely able to explore broad correlations between multiple star systems and the properties of the planets which they host, providing insight into the formation and evolution of planetary systems in our galaxy. Several KOIs of particular interest will be discussed, including possible quadruple star systems hosting planets and updated properties for possible rocky planets orbiting with in their star's habitable zone.

The major source of noise in high-contrast imaging is the presence of slowly evolving speckles that do not average with time. The temporal stability of the point-spread-function (PSF) is therefore critical to reach a high contrast with extreme adaptive optics (XAO) instruments. Understanding on which timescales the PSF evolves and what are the critical parameters driving the speckle variability allow to design an optimal observing strategy and data reduction technique to calibrate instrumental aberrations and reveal faint astrophysical sources. We have obtained a series of 52 min, AO-corrected, coronagraphically occulted, high-cadence (1.6Hz), H-band images of the star HR 3484 with the SPHERE (Spectro-Polarimeter High-contrast Exoplanet REsearch1) instrument on the VLT. This is a unique data set from an XAO instrument to study its stability on timescales as short as one second and as long as several tens of minutes. We find different temporal regimes of decorrelation. We show that residuals from the atmospheric turbulence induce a fast, partial decorrelation of the PSF over a few seconds, before a transition to a regime with a linear decorrelation with time, at a rate of several tens parts per million per second (ppm/s). We analyze the spatial dependence of this decorrelation within the well-corrected radius of the adaptive optics system and show that the linear decorrelation is faster at short separations. Last, we investigate the influence of the distance to the meridian on the decorrelation.

The Thirty Meter Telescope (TMT) first light instrument IRIS (Infrared Imaging Spectrograph) will complete its preliminary design phase in 2016. The IRIS instrument design includes a near-infrared (0.85 - 2.4 micron) integral field spectrograph (IFS) and imager that are able to conduct simultaneous diffraction-limited observations behind the advanced adaptive optics system NFIRAOS. The IRIS science cases have continued to be developed and new science studies have been investigated to aid in technical performance and design requirements. In this development phase, the IRIS science team has paid particular attention to the selection of filters, gratings, sensitivities of the entire system, and science cases that will benefit from the parallel mode of the IFS and imaging camera. We present new science cases for IRIS using the latest end-to-end data simulator on the following topics: Solar System bodies, the Galactic center, active galactic nuclei (AGN), and distant gravitationally-lensed galaxies. We then briefly discuss the necessity of an advanced data management system and data reduction pipeline.

Small inner working angle coronagraphs are essential to benefit from the full potential of large and future extremely large ground-based telescopes, especially in the context of the detection and characterization of exoplanets. Among existing solutions, the vortex coronagraph stands as one of the most effective and promising solutions. However, for focal-plane coronagraph, a small inner working angle comes necessarily at the cost of a high sensitivity to pointing errors. This is the reason why a pointing control system is imperative to stabilize the star on the vortex center against pointing drifts due to mechanical flexures, that generally occur during observation due for instance to temperature and/or gravity variations. We have therefore developed a technique called QACITS1 (Quadrant Analysis of Coronagraphic Images for Tip-tilt Sensing), which is based on the analysis of the coronagraphic image shape to infer the amount of pointing error. It has been shown that the flux gradient in the image is directly related to the amount of tip-tilt affecting the beam. The main advantage of this technique is that it does not require any additional setup and can thus be easily implemented on all current facilities equipped with a vortex phase mask. In this paper, we focus on the implementation of the QACITS sensor at Keck/NIRC2, where an L-band AGPM has been recently commissioned (June and October 2015), successfully validating the QACITS estimator in the case of a centrally obstructed pupil. The algorithm has been designed to be easily handled by any user observing in vortex mode, which is available for science in shared risk mode since 2016B.

Prior statistical knowledge of the turbulence such as turbulence strength, layer altitudes and the outer scale is essential for atmospheric tomography in adaptive-optics (AO). These atmospheric parameters can be estimated from measurements of multiple Shack-Hartmann wave-front sensors (SH-WFSs) by the SLOpe Detection And Ranging (SLODAR). In this paper, we present the statistics of the vertical CN^2 and the outer scale L_0 at Maunakea in Hawaii estimated from 60 hours telemetry data in total from multiple SH-WFSs of RAVEN, which is an on-sky multi-object AO demonstrator tested on the Subaru telescope. The mean seeing during the RAVEN on-sky observations is 0.475 arcsec, and 55% turbulence is below 1.5 km. The vertical profile of CN^2 from the RAVEN SLODAR is consistent with the profiles from CFHT DIMM and MASS, and TMT site characterization.

The TMT first light AO facility consists of the Narrow Field Infra-Red AO System (NFIRAOS), the associated Laser Guide Star Facility (LGSF) and the AO Executive Software (AOESW). Design, fabrication and prototyping activities of the TMT first light AO systems and their components have significantly ramped up in Canada, China, France, and in the US. NFIRAOS is an order 60 x 60 laser guide star (LGS) multi-conjugate AO (MCAO) system, which provides uniform, diffraction-limited performance in the J, H, and K bands over 34 x 34 arc sec fields with 50 per cent sky coverage at the galactic pole, as required to support the TMT science cases. NFIRAOS includes two deformable mirrors, six laser guide star wavefront sensors, one high order Pyramid WFS for natural guide star AO, and up to three low-order, IR, natural guide star on-instrument wavefront sensors (OIWFS) and four on-detector guide windows (ODGW) within each client instrument. The first light LGSF system includes six sodium lasers to generate the NFIRAOS laser guide stars. In this paper, we will provide an update on the progress in designing, prototyping, fabricating and modeling the TMT first light AO systems and their AO components over the last two years. TMT is continuing with detailed AO modeling to support the design and development of the first light AO systems and components. Major modeling topics studied during the last two years include further studies in the area of pyramid wavefront sensing, high precision astrometry, PSF reconstruction for LGS MCAO, LGSF wavefront error budget and sophisticated low order mode temporal filtering.

We present a speckle nulling code currently being used for high contrast imaging at the Palomar and Keck telescopes. The code can operate in open and closed loop and is self-calibrating, requiring no system model and minimal hand-coded parameters. Written in a modular fashion, it is straightforward to port to different instruments. It has been used with systems operating in the optical through thermal infrared, and can deliver nearly an order of magnitude improvement in raw contrast. We will be releasing this code to the public in the near future.

SPHERE is the VLT second generation planet hunter instrument. Installed since May 2014 on UT3, the system has been commissioned and verified for more than one year now and routinely delivers unprecedented images of star surroundings, exoplanets and dust disks. The exceptional performance required for this kind of observation makes the appointment: a repeatable Strehl Ratio of 90% in H band, a rough contrast level of 10-5@0.5 arcsec, and reaches 10-6 at the same separation after differential imaging (SDI, ADI). The instrument also presents high contrast levels in the visible and an unprecedented 17mas diffraction-limited resolution at 0.65 microns wavelength. SAXO is the SPHERE XAO system, allowing the system to reach its final detectivity. Its high performance and therefore highly sensitive capacities turns a new eye on telescope environment. Even if XAO performance are reached as expected, some unexpected limitations are here described and a first work around is proposed and discussed. Spatial limitation: wave-front aberrations have been identified, deviating from kolmogorov statistics, and therefore not easily seen and compensated for by the XAO system. The impact of this limitations results in a degraded performance in some particular low wind conditions. Solutions are developed and tested on sky to propose a new operation procedure reducing this limitation. Temporal limitation: high amplitude vibrations on the low order modes have been issued, due to telescope environment and XAO behaviour. Again, a solution is developed and an assessment of its performance is dressed. The potential application of these solutions to E-ELT is proposed.

Vortex coronagraphs are among the most promising solutions to perform high contrast imaging at small angular separations from bright stars. They feature a very small inner working angle (down to the diffraction limit of the telescope), a clear 360 degree discovery space, have demonstrated very high contrast capabilities, are easy to implement on high-contrast imaging instruments, and have already been extensively tested on the sky. Since 2005, we have been designing, developing and testing an implementation of the charge-2 vector vortex phase mask based on concentric sub-wavelength gratings, referred to as the Annular Groove Phase Mask (AGPM). Science-grade mid-infrared AGPMs were produced in 2012 for the first time, using plasma etching on synthetic diamond substrates. They have been validated on a coronagraphic test bench, showing broadband peak rejection up to 500:1 in the L band, which translates into a raw contrast of about 6 x 10^(-5) at 2⋋=D. Three of them have now been installed on world-leading diffraction-limited infrared cameras, namely VLT/NACO, VLT/VISIR and LBT/LMIRCam. During the science verification observations with our L-band AGPM on NACO, we observed the beta Pictoris system and obtained unprecedented sensitivity limits to planetary companions down to the diffraction limit (0.1"). More recently, we obtained new images of the HR 8799 system at L band during the AGPM first light on LMIRCam. After reviewing these first results obtained with mid-infrared AGPMs, we will discuss the short- and mid-term goals of the on-going VORTEX project, which aims to improve the performance of our vortex phase masks for future applications on second-generation high-contrast imager and on future extremely large telescopes (ELTs). In particular, we will briefly describe our current efforts to improve the manufacturing of mid-infrared AGPMs, to push their operation to shorter wavelengths, and to provide deeper starlight extinction by creating new designs for higher topo

Here we describe a prototype Strehl and image quality performance estimator and its integration into Paranal operations, starting with UT4 and its suite of three infrared instruments: adaptive optics-fed imager/spectrograph NACO (temporarily out of operations) and integral field unit SINFONI, as well as wide-field imager HAWK-I. The real-time estimator processes the ambient conditions (seeing, coherence time, airmass, etc.) from the DIMM, and telescope Shack-Hartmann image analyzer to produce estimates of image quality and Strehl ratio every ~ 30 seconds. The estimate is using ad-hoc instrumental models, based in part on the PAOLA adaptive optics simulator. We discuss the current performance of the estimator vs real IQ and Strehl measurements, its impact on service mode efficiency, prospects for full deployment at other UTs, its use for the adaptive optics facility (AOF), and inclusion of the SLODAR-measured fine turbulence characteristics.

We present the first observations obtained with the L'-band AGPM vortex coronagraph recently installed on LBTI/LMIRCam. The AGPM (Annular Groove Phase Mask) is a vector vortex coronagraph made from diamond subwavelength gratings. It is designed to improve the sensitivity and dynamic range of high-resolution imaging at very small inner working angles, down to 0.09 arcseconds in the case of LBTI/LMIRCam in the L' band. During the first hours on sky, we observed the young A5V star HR8799 with the goal to demonstrate the AGPM performance and assess its relevance for the ongoing LBTI planet survey (LEECH). Preliminary analyses of the data reveal the four known planets clearly at high SNR and provide unprecedented sensitivity limits in the inner planetary system (down to the diffraction limit of 0.09 arcseconds).

The extreme AO system, SAXO (SPHERE AO for eXoplanet Observation), is the heart of the SPHERE system, feeding the scientific instruments with flat wave front corrected from all the atmospheric turbulence and internal defects. We will present the final performance of SAXO obtained during the instrument AIT in Europe as well as the very first on-sky results. The main requirements and system characteristics will be recalled and the full AO loop performance will be quantified and compared to original specifications. It will be demonstrated that SAXO meets or even exceeds (especially its limit magnitude and its jitter residuals) its challenging requirements (more than 90% of SR in H band and a 3 mas residual jitter). Finally, after 10 years of AO developments, from early design to final on-sky implementations, some critical system aspects as well as some important lesson-learned will be presented in the perspective of the future generation of complex AO systems for VLTs and ELTs.

Discretized Aperture Mapping (DAM) appears as an original filtering technique easy to play with existing adaptive optics (AO) systems. In its essential DAM operates as an optical passive filter removing part of the phase residuals in the wavefront without introducing any difficult-to-align component in the Fourier conjugate of the entrance pupil plane. DAM reveals as a new interferometric technique combined with spatial filtering allowing direct imaging over a narrow field of view (FOV). In fact, the entrance pupil of a single telescope is divided into many sub-pupils so that the residual phase in each sub-pupil is filtered up to the DAM cut-off frequency. DAM enables to smooth the small scale wavefront defects which correspond to high spatial frequencies in the pupil plane and to low angular frequencies in the image plane. Close to the AO Nyquist frequency, such pupil plane spatial frequencies are not well measured by the wavefront sensor (WFS) due to aliasing. Once bigger than the AO Nyquist frequency, they are no more measured by the WFS due to the fitting limit responsible for the narrow AO FOV. The corresponding image plane angular frequencies are not transmitted by DAM and are useless to image small FOVs, as stated by interferometry. That is why AO and DAM are complementary assuming that the DAM cut-off frequency is equal to the AO Nyquist frequency. Here we describe the imaging capabilities when DAM is placed downstream an AO system, over a convenient pupil which precedes the scientific detector. We show firstly that the imaging properties are preserved on a narrow FOV allowing direct imaging throughout interferometry. Then we show how the residual pupil plane spatial frequencies bigger than the AO Nyquist one are filtered out, as well as the residual halo in the image is dimmed.

With two large deformable mirrors with a total of more than 7000 actuators that need to be driven from the measurements of six 60x60 LGS WFSs (total 1.23Mpixels) at 800Hz with a latency of less than one frame, NFIRAOS presents an interesting real-time computing challenge. This paper reports on a recent trade study to evaluate which current technology could meet this challenge, with the plan to select a baseline architecture by the beginning of NFIRAOS construction in 2014. We have evaluated a number of architectures, ranging from very specialized layouts with custom boards to more generic architectures made from commercial off-the-shelf units (CPUs with or without accelerator boards). For each architecture, we have found the most suitable algorithm, mapped it onto the hardware and evaluated the performance through benchmarking whenever possible. We have evaluated a large number of criteria, including cost, power consumption, reliability and flexibility, and proceeded with scoring each architecture based on these criteria. We have found that, with today’s technology, the NFIRAOS requirements are well within reach of off-the-shelf commercial hardware running a parallel implementation of the straightforward matrix-vector multiply (MVM) algorithm for wave-front reconstruction. Even accelerators such as GPUs and Xeon Phis are no longer necessary. Indeed, we have found that the entire NFIRAOS RTC can be handled by seven 2U high-end PC-servers using 10GbE connectivity. Accelerators are only required for the off-line process of updating the matrix control matrix every ~10s, as observing conditions change.

The vertical profile of the mesospheric sodium layer varies significantly on a time scale of one minute. These variations can impact the random and systematic measurement errors of laser guide star Shack-Hartmann wave front sensors, particularly on extremely large telescopes. Sensor performance can be improved by selecting pixel processing weights matched to the sodium layer profile, assuming that the shape of the profile can be measured or estimated in real time. In this paper we describe the magnitude of these effects for the Thirty Meter Telescope AO system NFIRAOS. We review several existing approaches for measuring or estimating the sodium layer profile in real time. We then describe a new method for estimating the profile directly from the laser guide star wave front pixel intensities themselves, jointly with the subaperture tip/tilt measurements. The algorithm used for this purpose is based upon the multi-frame iterative blind deconvolution algorithm from image post processing: Subaperture tip/tilts and the sodium profile are estimated successively, bootstrapping the estimate of each quantity from the previous estimate of the other. We present promising initial simulation results on the potential performance of the algorithm, and suggest areas for future work.

The Thirty Meter Telescope (TMT) with its first-light multi-conjugate adaptive optics system, NFIRAOS, and high-resolution imager, IRIS, is expected to take differential astrometric measurements with an accuracy on the order of tens of micro arcsec. This requires the control, correction, characterization and calibration of a large number of error sources and uncertainties, many of which have magnitudes much in excess of this level of accuracy. In addition to designing the observatory such that very high precision and accuracy astrometric observations are enabled, satisfying the TMT requirements can only be achieved by a careful calibration, observation and data reduction strategy. In this paper, we present descriptions of the individual errors sources, how and when they apply to different astrometry science cases and the mitigation methods required for each of them, as well as example results for individual error terms and the overall error budgets for a variety of different science cases.

The Laser Guide Star Facility (LGSF) system of the Thirty Meter Telescope (TMT) will generate the artificial laser guide stars required by the TMT Adaptive Optics (AO) systems. The LGSF uses multiple sodium lasers to generate and project several asterisms from a laser launch telescope located behind the TMT secondary mirror. The laser beams are transported from a location below the primary mirror to the launch telescope using conventional optics to relay the beams along the telescope structure. The beams and relay optics are enclosed into hermetic ducts for safety reasons and to protect the optics against the environment. A Computational Solid Fluid Dynamics (CSFD) model of the LGSF ducts has been developed. It resolves the duct thickness, laser beam transfer lenses, mirrors and their framework for most of the laser beam path that is subject to significant temperature gradients and/or large vertical change. It also resolves the air inside the duct and its thermal interaction with the aforementioned components through conjugate heat transfer. The thermal interaction of the laser beam with the optics is also captured. The model provides guidance to the LGSF design team and a first estimate of the laser beam stability performance and requirement compliance. As the telescope structure design has evolved in the recent years, a new optical path has been proposed for the LGSF. Both the original and the new optical paths are compared against optical, mechanical and other telescope performance related criteria. The optical performance criteria include a first order analysis of the optical turbulence generated within the ducts. In this study simulations of the thermal environment within the ducts of the two candidate paths are performed and conclusions are drawn.

Palomar’s Project 1640 (P1640) is the first stellar coronagraph to regularly use active coronagraphic wavefront control (CWFC). For this it has a hierarchy of offset wavefront sensors (WFS), the most important of which is the higher-order WFS (called CAL), which tracks quasi-static modes between 2-35 cycles-per-aperture. The wavefront is measured in the coronagraph at 0.01 Hz rates, providing slope targets to the upstream Palm 3000 adaptive optics (AO) system. The CWFC handles all non-common path distortions up to the coronagraphic focal plane mask, but does not sense second order modes between the WFSs and the science integral field unit (IFU); these modes determine the system’s current limit. We have two CWFC operating modes: (1) P-mode, where we only control phases, generating double-sided darkholes by correcting to the largest controllable spatial frequencies, and (2) E-mode, where we can control amplitudes and phases, generating single-sided dark-holes in specified regions-of-interest. We describe the performance and limitations of both these modes, and discuss the improvements we are considering going forward.