Search

A tapered Er-doped fiber amplifier for high peak power pulses amplification has been developed and tested. The core diameter changed from 15.8 µm (mode field diameter (MFD) 14.5 µm) to 93 µm (MFD 40 µm) along 3.7 m maintaining single-mode performance at 1555 nm (according to the S2-method, the part of the power of high-order modes does not exceed 1.5%). The amplification of 0.9 ns pulses with spectral width below 0.04 nm up to a peak power above 200 kW (limited by self-phase modulation) with a slope pump-to-signal conversion efficiency of 15.6% was demonstrated.

In the paper we discuss current state of the art in the field of tapered fiber development. The best results in term of high peak and high average power achieved with this type of fibers are presented together with requirements to the tapered fiber amplifier design. The report is mainly focused on tapered fiber amplifiers operated near 1 μm (Yb-doped tapered fibers), but also extension of this technique to 1.55 μm spectral range is discussed.

In this paper we systematically study a limitation for maximum of Yb dopant concentration in silica based fibers. Two the most popular glass matrixes (F-Al2O3-SiO2 and Al2O3-P2O5-SiO2) were thoroughly investigated in this respect. A possibility to introduce ultra-high doping level of Yb2O3 (in excess of 2.5 mol%) with a relatively low optical losses in fibers was demonstrated. At the same time it was investigated that at ultra-high Yb concentration in the fiber core even with maintaining very low background losses (both initial and induced by photodarkening) such a fiber can nearly completely lose its active properties. Optimal glass matrixes and optimal concentration of Yb dopant in the glass core, which allow keep up lasing properties of the developed fibers high, were studied. An ultra-short length fiber amplifier (~3.5 cm) based on the developed Al2O3-P2O5-SiO2 glass core fiber doped with 1.2 mol% of Yb2O3 (Yb ions absorption was about 1000 dB/m at 920 nm) was created.

In this paper, we demonstrate possibility of simultaneous achievement of high peak and high average power in picosecond pulses using a monolithic amplifier based on a long Yb-doped tapered fiber. Due to a very high pump absorption (~ 25 dB/m at 976 nm) in the realized 2.4 m long tapered fiber most of the pump is absorbed near the thick tapered fiber end and a very small fraction of pump power reaches thin fiber end. As a result, signal passes through the thin part of the tapered fiber without an amplification and exhibits fast growth only near the output tapered fiber end, where a mode field diameter is large (35 μm at 1064 nm for 46 μm output core diameter), so that pulses can be amplified to a high peak power. Moreover, only a negligible fraction of pump radiation leaks at the conic part of the tapered fiber, because its most part was absorbed in the thick tapered fiber part. Thus a safe operation without polymer burning at a leakage point is possible up to a very high pump power. The developed tapered fiber was used in a final amplification stage of the all-fiber pulsed laser system, which allowed us to amplify 8.3 ps pulses with repetition rate of 18.4 MHz and central wavelength of 1064 nm to 150 W of average power and 0.92 MW peak power. The average power level was limited only by available pump power (230 W): no signs of transverse mode instability effects were observed.

Single-mode Er-Yb fibers based on phosphorosilicate glass matrix highly doped with fluorine have been fabricated using modified all-gas phase MCVD technology. Fibers have core doped by 6.5 mol.% of P2O5, 0.9 wt.% of F and different concentration of Er and Yb. The core NA was about 0.07-0.08 relative to the pure silica level. Slope efficiency of more than 19% was achieved using amplifier scheme with co-propagating pump at 976 nm and signal at 1555 nm (input signal power was about 0.6W). Slope efficiency in the laser configuration has reached 34% relative to the input pump power.

Monolithic 976 nm laser design based on a newly developed saddle-shaped Yb-doped fiber has been proposed. The fiber has central single-mode part with core diameter of about 12 μm and ultra-thin square-shaped clad with side of about 42x42 μm. At the both ends of the saddle-shaped fiber the core and the clad sizes were adiabatically increased up to 20/(70x70) μm and the fiber could be spliced with standard (80..125 μm clad) passive fibers using commercially available equipment. Single-mode laser at 976 nm based on the developed fiber has been fabricated and photodarkening-free operation with output power of 10.6 W, which is the record high for all-fiber laser schemes, has been demonstrated.

Chirped pulse monolithic fiber amplifier based on a newly developed tapered polarization maintaining Yb-doped fiber has been developed and optimized. A novel amplification regime in a relatively long (220 cm) tapered fiber of improved design, which has been theoretically predicted, allowed us to achieve an ultimate high peak power. In this regime, the signal propagates most of the fiber without amplification and growths very rapidly only in the last 80 cm of the tapered fiber, which has a mode field area of approximately 1000 μm2 near the output. We have demonstrated amplification of 20 ps chirped pulses centered at 1056-nm with spectral width of 20 nm to 0.7 MW peak power directly from the tapered fiber amplifier. The pulses had a diffraction limited quality (M2 ~ 1.124) and could be compressed down to 350 fs with 50% efficiency. In addition, amplification of narrow-band 9 ps pulses centered at 1064 nm to a peak power of 1.8 MW directly from the tapered fiber amplifier was demonstrated.

Experimental observation of a novel effect of long-term mode shape degradation in a high peak power ytterbium-doped pulsed fiber lasers based on large mode area step-index fibers has been reported for the first time. It is shown, that the degradation is caused by power coupling from LP01 to LP11 mode, occurring on a long period refractive index grating (LPG) formed in the active fiber core. The photo-darkening process was found to play a significant role in the formation of a LPG.

In this work we present a monolithic lidar system, based on a newly-developed double-clad large mode area (LMA) polarization-maintaining Er-doped fiber and specially designed LMA passive components. Optimization of the fiber designs resulted in as high as 100 W of SBS limited peak power. The amplifier and its passive components (circulator and collimator) were integrated in an existing lidar system. The enhanced lidar system provides three times increase of scanning range compared to one based on standard telecom-grade amplifiers.

An all-glass Yb-doped single-mode fiber laser and amplifier with output power of more than 5 W near 977 nm have been realized. Both laser and amplifier were based on a specially developed photodarking-free Yb-doped fibers with increased core-to-clad diameter ratio (up to 0.31).

In this study, we present a novel monolithic ytterbium-doped fiber amplifier with more than 0.5 MW peak power output power. The amplifier is based on a 2.1 m long tapered fiber with core/cladding diameters changing from 10/80 µm (at the signal input end) to 50/430 µm (signal output, pump input). The fiber has all-glass polarization-maintaining design, that make possible utilization of conventional FC adapter and standard angle polishing to 7° for thick end. Pump absorption was measured to be 8 dB at 915 nm for the whole fiber length. Despite a very large mode area (~30 µm) the tapered fiber demonstrates low bend sensitivity (it is possible to coil tapered fiber with 9 cm radius) and a diffraction limited beam quality. In the amplifier the pump power was coupled through the thick end by means of collimating and focusing lenses. Dichroic mirror employed to separate output signal and counter-propagating pump power. We obtained 3.5 W of average output power for a 5 mW seed signal (coupled by usual fusion splicing through a thin end) corresponding to a 28 dB gain. The amplified pulses have duration of about 5 ps and energy of about 3.3 µJ that corresponding to over 0.5 MW peak power. The spectral width was 28 nm operating with center wavelength of 1057 nm.To the best of our knowledge it is the highest peak power obtained directly from the all-fiber amplifier.. Keywords: Yb-doped tapered fiber, all-fiber megawatt system, low bend sensitive tapered fiber, ultrashort pulses amplification 1. INTRODUCTION The very rapid power scaling of both pulsed and cw Yb-doped fiber lasers dictates stringent requirements on the utilized fibers, mainly in terms of nonlinear effects threshold. Conventional single-mode Yb-doped fibers exhibit a relatively low threshold for nonlinear effects since the light is confined in a small core (6-10 µm in diameter) and propagates along long distances (above 10 m in some cases). The increasing of nonlinearity threshold is the urgent problem in the case of pulsed fiber systems, which have been demonstrated to reach power levels of several hundreds of kW and even approach MW power level. The most simple and obvious way to solve this problem is the enlargement of core diameter resulting in the enlarged mode filed diameter of the fundamental mode. In the same time, this approach has so me drawbacks: the fiber becomes a multimode, leading to degradation of output beam quality, and extremely bend-sensitive, resulting in requirement to keep the fiber straight, i.e. the system becomes cumbersome. The main goal of this work was to develop a novel approach based on utilizing of so-called tapered fibers that allows one to obtain large mode field areas and maintain an acceptable bend-loss sensitivity at the same time. The fiber parameters optimization and its using in the final amplification stage of picosecond chirped-pulse amplification system have been demonstrated. The obtained output peak power was record for all-fiber amplifying systems and approached by power level of microstructured fibers based systems.

We have studied the photodarkening effect in fiber preforms with an ytterbium-doped aluminosilicate glass core. The room-temperature stable Yb2+ ions formation in the glass matrix under both UV- and NIR-pumping irradiation was revealed by the method of absorption spectra analysis and the fluorescence spectroscopy technique. Comparative studies of preforms and crystals samples luminescence spectra, obtained under UV-excitation, were performed. A general mechanism of Yb2+ ions and aluminium oxygen-hole centers (Al-OHC) formation as a result of photoinduced process of Yb3+ ions excitation to "charge-transfer state" (CTS) was found for both Yb:YAG crystal and aluminosilicate glass.