Search

PFS (Prime Focus Spectrograph), a next generation facility instrument on the Subaru telescope, is a very wide- field, massively multiplexed, and optical and near-infrared spectrograph. Exploiting the Subaru prime focus, 2394 reconfigurable fibers will be distributed in the 1.3 degree-diameter field of view. The spectrograph system has been designed with 3 arms of blue, red, and near-infrared cameras to simultaneously deliver spectra from 380nm to 1260nm in one exposure. The instrumentation has been conducted by the international collaboration managed by the project office hosted by Kavli IPMU. The team is actively integrating and testing the hardware and software of the subsystems some of which such as Metrology Camera System, the first Spectrograph Module, and the first on-telescope fiber cable have been delivered to the Subaru telescope observatory at the summit of Maunakea since 2018. The development is progressing in order to start on-sky engineering observation in 2021, and science operation in 2023. In parallel, the collaboration is trying to timely develop a plan of large-sky survey observation to be proposed and conducted in the framework of Subaru Strategic Program (SSP). This article gives an overview of the recent progress, current status and future perspectives of the instrumentation and scientific operation.

The Fiber Optic Cable and Connector System, FOCCoS, is a set of optical cables to feed the Prime Focus Spectrograph, PFS, for Subaru telescope [01,02]. The extremity responsible for delivering light to spectrographs is called, FCA, Fiber Cable A. Cable A is the cable installed at the Spectrograph side and consists of the Fiber Slit Assembly, FSA, the routing with its support and the Fiber Input Assembly, FIA. FSA is composed of a set of optical fibers arranged linearly on the Slit device and supported by the Frame, protected by segmented tubes and routed between strain relief boxes and the connection interface. FIA is composed by the Connector Bench (Gang Connector) that allow connection with Cable B, at the Subaru Telescope interface, to receive light from Cable C where the fibers end is coupled with microlens. As four Spectrographs are considered for PFS/Subaru, four units of Cable A are necessary. In this paper, we present in details of a complete FCA to be installed in the spectrograph bench. We discuss about the general design, methods used to manufacture the involved devices.

The focal ratio degradation effects on optical fibers, technically referred to as FRD, has been the subject of intense studies since the beginning of the use of optical fibers in the construction of instruments applied in astronomy. A number of studies attempt to relate FRD to light loss in the optical system and other studies attempt to qualify and quantify FRD as a function of the stress induced during assembly of the structures supporting the ends of the optical fibers. In this work, we present a large-scale study to characterize FRD in all the fibers that make up the cables of the FOCCoS, Fiber Optical Cable and Connectors System project. FOCCoS, has the main function of capturing the direct light from the focal plane of Subaru Telescope using 2400 optical fibers, each one with a microlens in its tip, and conducting this light through a route containing connectors to a set of four spectrographs. The optical fiber cable is divided in 3 different segments called Cable A, Cable B and Cable C. Multi-fibers connectors assure precise connection among all optical fibers of the segments, providing flexibility for instrument changes. Our study provides procedures and methods to analyze the effects of FRD on all cable segments for each type of termination involved. Special attention is devoted to the understanding of how angular deviations between the input surface of the fiber and the test beam can significantly influence the calculation of FRD in optical fibers.

The Fiber Optical Cable and Connector System, ”FOCCoS”, subsystem of the Prime Focus Spectrograph, “PFS”, for Subaru telescope, is responsible to feed four spectrographs with a set of optical fibers cables. The light injection for each spectrograph is assured by a convex curved slit with a linear array of 616 optical fibers. In this paper we present a design of a slit that ensures the right direction of the fibers by using masks of micro holes. This kind of mask is made by a technique called electroforming, which is able to produce a nickel plate with holes in a linear sequence. The precision error is around 1-μm in the diameter and 1-μm in the positions of the holes. This nickel plate may be produced with a thickness between 50 and 200 microns, so it may be very flexible. This flexibility allows the mask to be bent into the shape necessary for a curved slit. The concept requires two masks, which we call Front Mask, and Rear Mask, separated by a gap that defines the thickness of the slit. The pitch and the diameter of the holes define the linear geometry of the slit; the curvature of each mask defines the angular geometry of the slit. Obviously, this assembly must be mounted inside a structure rigid and strong enough to be supported inside the spectrograph. This structure must have a CTE optimized to avoid displacement of the fibers or increased FRD of the fibers when the device is submitted to temperatures around 3 degrees Celsius, the temperature of operation of the spectrograph. We have produced two models. Both are mounted inside a very compact Invar case, and both have their front surfaces covered by a dark composite, to reduce stray light. Furthermore, we have conducted experiments with two different internal structures to minimize effects caused by temperature gradients. This concept has several advantages relative to a design based on Vgrooves, which is the classical option. It is much easier and quicker to assemble, much cheaper, more accurate, easier to adjust; and it also offers the possibility of making a device much more strong, robust and completely miniaturized.

FOCCoS, Fiber Optical Cable and Connector System, has the main function of capturing the direct light from the focal plane of Subaru Telescope using optical fibers, each one with a microlens in its tip, and conducting this light through a route containing connectors to a set of four spectrographs. The optical fiber cable is divided in 3 different segments called Cable A, Cable B and Cable C. Multi-fibers connectors assure precise connection among all optical fibers of the segments, providing flexibility for instrument changes. To assure strong and accurate connection, these sets are arranged inside two types of assemblies: the Tower Connector, for connection between Cable C and Cable B; and the Gang Connector, for connection between Cable B and Cable A. Throughput tests were made to evaluate the efficiency of the connections. A lifetime test connection is in progress. Cable C is installed inside the PFI, Prime Focus Instrument, where each fiber tip with a microlens is bonded to the end of the shaft of a 2-stage piezo-electric rotatory motor positioner; this assembly allows each fiber to be placed anywhere within its patrol region, which is 9.5mm diameter.. Each positioner uses a fiber arm to support the ferrule, the microlens, and the optical fiber. 2400 of these assemblies are arranged on a motor bench plate in a hexagonal-closed-packed disposition., 11 pages, 20 figures