Search

Cementation of salt-containing soils can be achieved by salt-tolerant or halophilic calcite precipitation bacteria. Therefore, the isolation of calcite-producing bacteria in the presence of salt is the first step in the microbial cementation of saline soils. Urease producing bacteria can cause calcite nano-crystals to precipitate by producing urease in the presence of urea and calcium. The purpose of this study was to isolate urease producing halophilic bacteria in order to make calcite precipitate in saline soil. The calcite and the properties of the strains were further analyzed by X-ray diffraction (XRD) and scanning electron microscope equipped with an energy dispersive X-ray detector. In this study, a total of 110 halophilic strains were isolated, from which 58 isolates proved to have the ability of urease production. Four strains were identified to produce nano-calcite using urease activity in the precipitation medium. The XRD studies showed that the size of these particles was in the range of 40-60 nm. Strain H3 revealed that calcite is mostly produced in the precipitation medium containing 5% salt in comparison with other strains. This strain also produced calcite precipitates in the precipitation medium containing 15% salt. Phylogenetic analysis indicated that these isolates are about 99-100% similar to Staphylococcus saprophyticus.

Highly porous hydroxyapatite (Ca(10)(PO(4))(6)·(OH)(2), HA) was prepared through hydrothermal transformation of aragonitic cuttlefish bones (Sepia officinalis L. Adriatic Sea) in the temperature range from 140 to 220°C for 20 min to 48 h. The phase composition of converted hydroxyapatite was examined by quantitative X-ray diffraction (XRD) using Rietveld structure refinement and Fourier transform infrared spectroscopy (FTIR). Johnson-Mehl-Avrami (JMA) approach was used to follow the kinetics and mechanism of transformation. Diffusion controlled one dimensional growth of HA, predominantly along the a-axis, could be defined. FTIR spectroscopy determined B-type substitutions of CO(3) (2-) groups. The morphology and microstructure of converted HA was examined by scanning electron microscopy. The general architecture of cuttlefish bones was preserved after hydrothermal treatment and the cuttlefish bones retained its form with the same channel size (~80 × 300 μm). The formation of dandelion-like HA spheres with diameter from 3 to 8 μm were observed on the surface of lamellae, which further transformed into various radially oriented nanoplates and nanorods with an average diameter of about 200-300 nm and an average length of about 8-10 μm.

Hydroxyapatite structures for tissue engineering applications have been produced by hydrothermal (HT) treatment of aragonite in the form of cuttlefish bone at 200 degrees C. Aragonite (CaCO(3)) monoliths were completely transformed into hydroxyapatite after 48 h of HT treatment. The substitution of CO(3) (2-) groups predominantly into the PO(4) (3-) sites of the Ca(10)(PO(4))(6)(OH)(2) structure was suggested by FT-IR spectroscopy and Rietveld structure refinement. The intensity of the nu(3)PO(4) (3-) bands increase, while the intensity of the nu(2)CO(3) (2-) bands decrease with the duration of HT treatment resulting in the formation of carbonate incorporating hydroxyapatite. The SEM micrographs have shown that the interconnected hollow structure with pillars connecting parallel lamellae in cuttlefish bone is maintained after conversion. Specific surface area (S (BET)) and total pore volume increased and mean pore size decreased by HT treatment.

Ceramic composites composed of constituents with different bone cell reactions present an interesting consideration for a new bone replacement material. The first component of the composite used in this study, hydroxyapatite, is known to be replaced by natural tissue significantly slower than the second, calcium carbonate, which has limited structural stability. A graded hydroxyapatite/calcium carbonate composite with bimodal component distribution was developed using a combined slip infiltration and dip-coating technique from a porous polyurethane sponge replica. A graded hydroxyapatite scaffold with porosities from 5 to 90% was produced and then infiltrated with a calcium carbonate slip and sintered. The resultant composite had improved mechanical properties compared with the monolith as measured by crushing and moduli tests.