Search

Most microbiologically influenced corrosion (MIC) studies focus on the threat of pinhole leaks caused by MIC pitting. However, microbes can also lead to structural failures. Tetrakis hydroxymethyl phosphonium sulfate (THPS) biocide mitigated the microbial degradation of mechanical properties of X80 steel pipeline by Desulfovibrio ferrophilus (IS5 strain), a very corrosive sulfate reducing bacterium. It was found that 100 ppm (w/w) THPS added to the enriched artificial seawater (EASW) culture medium before incubation resulted in 2.8-log reduction in sessile cell count after a 7-d incubation at 28 °C under anaerobic conditions, leading to 94% uniform corrosion rate reduction (from 1.3 to 0.07 mm/a), and 84% pitting corrosion rate reduction (from 0.70 to 0.11 mm/a). The X80 dogbone coupon incubated with 100 ppm THPS for 7 d suffered 3% loss in ultimate tensile strain and 0% loss in ultimate tensile strength compared with the abiotic control in EASW. In comparison, the no-treatment X80 dogbone coupon suffered losses of 13% in ultimate tensile strain and 6% in ultimate tensile stress, demonstrating very good THPS efficacy. [ABSTRACT FROM AUTHOR]

In recent decades, urban energy consumption and carbon emissions have expanded rapidly on a global scale. Building sector, in particular, accounts for approximately 40% of overall energy use. Urban planners and decision-makers have a significant responsibility to achieve sustainable energy and climate objectives. Urban building energy modeling (UBEM) has increased in popularity in recent years as a tool for calculating urban-scale energy use in buildings with limited resources, and that facilitated the formulation of new energy policies. However, published studies of UBEM methodologies and tools lack comprehensive examinations of the potential limitations of research and the prospects of future opportunities. This paper provides a complete conceptual framework for UBEM based on extensive literature reviews and prior researchers’ work. In addition to providing a comprehensive understanding of the various UBEM approaches and tools, future research directions are explored. The results demonstrate that earlier researches did not adequately account for input uncertainty and lacked proper simulation and calibration control for algorithms/models. These challenges not only increased the workload and computational burden of modelers but also diminished the precision of model calculations. In response, this paper provides targeted recommendations for each essential phase of the present UBEM workflow, namely model input, model development, and model calibration, to address these limitations, as well as a comprehensive analysis of future prospects. The main aim of the research is to further UBEM development as a faster, more accurate and multiscale supportive tool and establish a framework for future UBEM methods. [ABSTRACT FROM AUTHOR]

In modern societies, the accumulation of vast amounts of waste Li-ion batteries (WLIBs) is a grave concern. Bioleaching has great potential for the economic recovery of valuable metals from various electronic wastes. It has been successfully applied in mining on commercial scales. Bioleaching of WLIBs can not only recover valuable metals but also prevent environmental pollution. Many acidophilic microorganisms (APM) have been used in bioleaching of natural ores and urban mines. However, the activities of the growth and metabolism of APM are seriously inhibited by the high concentrations of heavy metal ions released by the bio-solubilization process, which slows down bioleaching over time. Only when the response mechanism of APM to harsh conditions is well understood, effective strategies to address this critical operational hurdle can be obtained. In this review, a multi-scale approach is used to summarize studies on the characteristics of bioleaching processes under metal ion stress. The response mechanisms of bacteria, including the mRNA expression levels of intracellular genes related to heavy metal ion resistance, are also reviewed. Alleviation of metal ion stress via addition of chemicals, such as spermine and glutathione is discussed. Monitoring using electrochemical characteristics of APM biofilms under metal ion stress is explored. In conclusion, effective engineering strategies can be proposed based on a deep understanding of the response mechanisms of APM to metal ion stress, which have been used to improve bioleaching efficiency effectively in lab tests. It is very important to engineer new bioleaching strains with high resistance to metal ions using gene editing and synthetic biotechnology in the near future. [ABSTRACT FROM AUTHOR]

High metal ion concentrations and low pH cause severely inhibit the activity of an acidophilic microbial consortium (AMC) in bioleaching. This work investigated the effects of exogenous spermine on biofilm formation and the bioleaching efficiency of LiCoO2 by AMC in 9K medium. After the addition of 1 mM spermine, the activities of glutathione peroxidase and catalase increased, while the amount of H2O2, intracellular reactive oxygen species (ROS) and malondialdehyde in AMC decreased. These results indicated that the ability of AMC biofilm to resist oxidative stress introduced by 3.5 g/L Li+ and 30.1 g/L Co2+ was improved by spermine. The activity of glutamate decarboxylase was promoted to restore the intracellular pH buffering ability of AMC. Electrochemical measurements showed that the oxidation rate of pyrite was increased by exogenous spermine. As a result, high bioleaching efficiencies of 97.1% for Li+ and 96.1% for Co2+ from a 5.0% (w v−1) lithium cobalt oxide powder slurry were achieved. This work demonstrated that Tafel polarization can be used to monitor the AMC biofilm’s ability of uptaking electrons from pyrite during bioleaching. The corrosion current density increased with 1 mM spermine, indicating enhanced electron uptake by the biofilm from pyrite. [ABSTRACT FROM AUTHOR]

Biocorrosion, also called microbiologically influenced corrosion (MIC), is a common operational threat to many industrial processes. It threatens carbon steel, stainless steel and many other metals. In the bioprocessing industry, reactor vessels in biomass processing and bioleaching are prone to MIC. MIC is caused by biofilms. The formation and morphology of biofilms can be impacted by fluid flow. Fluid velocity affects biocide distribution and MIC. Thus, assessing the efficacy of a biocide for the mitigation of MIC under flow condition is desired before a field trial. In this work, a benchtop closed flow loop bioreactor design was used to investigate the biocide mitigation of MIC of C1018 carbon steel at 25 °C for 7 days using enriched artificial seawater. An oilfield biofilm consortium was analyzed using metagenomics. The biofilm consortium was grown anaerobically in the flow loop which had a holding vessel for the culture medium and a chamber to hold C1018 carbon steel coupons. Peptide A (codename) was a chemically synthesized cyclic 14-mer (cys-ser-val-pro-tyr-asp-tyr-asn-trp-tyr-ser-asn-trp-cys) with its core 12-mer sequence originated from a biofilm dispersing protein secreted by a sea anemone which possesses a biofilm-free exterior. It was used as a biocide enhancer. The combination of 50 ppm (w/w) THPS (tetrakis hydroxymethyl phosphonium sulfate) biocide + 100 nM (180 ppb by mass) Peptide A resulted in extra 1-log reduction in the sulfate reducing bacteria (SRB) sessile cell count and the acid producing bacteria (APB) sessile cell count compared to 50 ppm THPS alone treatment. Furthermore, with the enhancement of 100 nM Peptide A, extra 44% reduction in weight loss and 36% abatement in corrosion pit depth were achieved compared to 50 ppm THPS alone treatment. [ABSTRACT FROM AUTHOR]

Microbiologically influenced corrosion (MIC), or microbial biocorrosion, is caused directly by microbial metabolic activities/products or induced by microbial biofilm's damage of a protective film that exposes a solid surface to a pre-existing corrosive environment. MIC causes billions of dollars of losses in various industrial processes, especially in oil and gas and water utilities. The mitigation of problematic industrial microbes typically relies on biocides whose discharges can cause environmental problems. Thus, more effective biocide applications are desired to minimize environmental impact. D-Limonene, a citrus peel oil, generally regarded as safe (GRAS), was used to enhance the popular biodegradable tetrakis hydroxymethyl phosphonium sulfate (THPS) biocide. An oilfield mixed-culture biofilm was grown anaerobically in enriched artificial seawater containing C1018 carbon steel coupons for 7 days at 37 °C. One hundred ppm (w/w) D-limonene reduced general heterotrophic bacteria (GHB) and acid-producing bacteria (APB) effectively, leading to 5.4-log and 6.0-log reductions in sessile GHB and APB cell counts, respectively, compared to no treatment control. The combination of 100 ppm D-limonene + 100 ppm THPS achieved extra 1.0-log SRB, 0.6-log GHB and 0.5-log APB reductions in sessile cell counts, which led to extra 58% reduction in microbial corrosion mass loss (1.2 vs. 0.5 mg/cm2) and extra 30% reductions in maximum pit depth (11.5 vs. 8.1 µm), compared to 100 ppm THPS-only treatment. Linear polarization resistance and potentiodynamic polarization (PDP) corrosion data supported mass loss and pitting data. Mixed-culture biofilms on carbon steel coupons after 7 day incubation at 37 °C showing enhanced biocide treatment outcome using D-limonene + THPS: A no treatment, B 100 ppm D-limonene, C 100 ppm THPS, D 100 ppm D-limonene + 100 ppm THPS. [ABSTRACT FROM AUTHOR]

Trehalase can biocatalyze the conversion of trehalose to glucose. It is an enzyme that plays an important role in biofilm formation. Thus, trehalase has been patented as a chemical for preventing and treating biofilms. Sulfate-reducing bacteria (SRB) biofilms are often found responsible for biocorrosion, also known as microbiologically infuenced corrosion (MIC), especially in the oil and gas industries and in water utilities. The MIC treatment process typically requires biocide treatment of biofilms, sometimes together with scrubbing. Owing to environmental concerns, a lower biocide dosage is desired in the treatment process. In this work, trehalase was tested as a green biocide enhancer to enhance tetrakis hydroxymethyl phosphonium sulfate (THPS) in the prevention of Desulfovibrio vulgaris MIC of C1018 carbon steel in ATCC 1249 culture medium at 37 °C. THPS is one of the most popular industrial biocides owing to its broad-spectrum efficacy and green chemical status. After 7 days of incubation in 50 mL anaerobic vials containing 40 mL culture medium at pH 7.0, the sessile cell counts indicated that 50 ppm (w/w) THPS + 30 ppm (w/w) trehalase led to an extra 5.7-fold sessile cell reduction when compared with the 50 ppm THPS alone treatment. As a consequence, the combination treatment also resulted in an extra 54% in pit depth reduction and 30% in weight loss reduction when compared with the 50 ppm THPS alone treatment (with 9.0 μm and 1.0 mg/cm2). The biofilm images corroborated the decreased sessile cell count and pitting corrosion. [ABSTRACT FROM AUTHOR]

The protection of marine materials against corrosion using marine bacterial biofilms is a promising strategy. However, little is known about the mechanisms of this attractive corrosion prevention method. In this work, the corrosion behaviors of X80 carbon steel (CS) in the presence of three different marine Vibrio species were studied. The results demonstrated that all the three Vibrio spp. displayed significant corrosion protection with a weight loss reduction of up to 68%. Moreover, their corrosion prevention performance was tightly related to their abilities to form biofilms, which was in the order of Vibrio sp. EF187016 > Vibrio alginolyticus > Vibrio parahaemolyticus. To further investigate the corrosion prevention mechanism caused by marine biofilms, the extracellular polymeric substances (EPS) of Vibrio sp. EF187016 was extracted and added to 3.5 wt% NaCl for abiotic corrosion testing. The results suggested that the EPS inhibited corrosion, which means EPS can play a significant role in corrosion protection by biofilm. [ABSTRACT FROM AUTHOR]

With increased popularity and technological innovation, more and more electric and electronic equipment wastes (e-wastes) are being generated. Printed circuit boards (PCBs) as fundamental components of electronic wastes, consist of both precious and heavy metals. In this research, the simultaneous extraction Cu and Zn from PCBs used in mobile phones with a natural organic acid and H2O2 was examined. The organic acid was determined from agricultural lemon fruit. The leaching extraction factors investigated include lemon juice concentration, solid/liquid (S/L) ratio, and H2O2 concentration. Response surface methodology (RSM) was applied to optimize the extraction which resulted in the maximum recoveries of 89% Cu and 73% Zn at 1.41% (w/v) S/L ratio, 12.2% (v/v) H2O2, and 74% (v/v) lemon juice after 4 h at 20 °C. The effect of time on the Cu and Zn recoveries at the determined optimum condition was examined. Furthermore, a kinetic study based on a shrinking core model was performed and the result showed that mass diffusion was rate-limiting in the extraction. [ABSTRACT FROM AUTHOR]

Microbiologically influenced corrosion (MIC) is one of the major corrosion threats in the oil and gas industry. It is caused by environmental biofilms. Glutaraldehyde is a popular green biocide for mitigating biofilms and MIC. This work investigated the efficacy of glutaraldehyde enhancement by food-grade green chemical d-limonene in the biofilm prevention and MIC mitigation using a mixed-culture oilfield biofilm consortium. After 7 days of incubation at 37 °C in enriched artificial seawater in 125 mL anaerobic vials, the 100 ppm (w/w) glutaraldehyde + 200 ppm d-limonene combination treatment reduced the sessile cell counts on C1018 carbon steel coupons by 2.1−log, 1.7−log, and 2.3−log for sulfate reducing bacteria, acid producing bacteria, and general heterotrophic bacteria, respectively in comparison with the untreated control. The treatment achieved 68% weight loss reduction and 78% pit depth reduction. The 100 ppm glutaraldehyde + 200 ppm d-limonene combination treatment was found more effective in biofilm prevention and MIC mitigation than glutaraldehyde and d-limonene used individually. Electrochemical tests corroborated weight loss and pit depth data trends. [ABSTRACT FROM AUTHOR]

During bioleaching of Cobalt from waste lithium-ion batteries, the biooxidation activity of acidophilic bacteria is inhibited by a high concentration of Co ion in the liquid phase. However, the mechanism for Co2+ toxicity to acidophilic bacteria has not been fully elucidated. In this study, the effects of Co2+ concentration on the biooxidation activity for Fe2+, intracellular reactive oxygen species (ROS) level and antioxidant defense systems in a mixed-culture of acidophilic bacteria (MCAB) were investigated. The results showed that the biooxidation activity of the MCAB was inhibited by Co2+. Furthermore, it was indicated that the intracellular ROS contents of the MCAB under conditions of 0.4 M and 0.6 M Co2+ were 2.60 and 3.34 times higher than that under the condition of 0 M Co2+. The increase in intracellular malondialdehyde content indicated that the oxidative damage was induced by Co2+. Moreover, the antioxidant systems in MCAB were affected by Co2+. It was observed that the Co2+ exposure increased the catalase and glutathione peroxidase activities while reducing the superoxide dismutase activity and the intracellular glutathione (GSH) content. It was found that an exogenous GSH supplementation eliminated excess intracellular ROS and improved the biooxidation activity of the MCAB. [ABSTRACT FROM AUTHOR]

Microbial fuel cells (MFCs) face major hurdles for real-world applications as power generators with the exception of powering small sensor devices. Despite tremendous improvements made in the last two decades, MFCs are still too expensive to build and operate and their power output is still too small. In view of this, in recently years, intensive researches have been carried out to expand the applications into other areas such as acid and alkali production, bioremediation of aquatic sediments, desalination and biosensors. Unlike power applications, MFC sensors have the immediate prospect to be practical. This review covers the latest developments in various proposed biosensor applications using MFCs including monitoring microbial activity, testing biochemical oxygen demand, detection of toxicants and detection of microbial biofilms that cause biocorrosion. [ABSTRACT FROM AUTHOR]

Cyclodextrins (CDs) are a family of cyclic-oligosaccharides with usually 6–8 glucopyranose units. Because of their unique donut-shaped steric structure they are able to form inclusion complexes selectively with some guest molecules. CDs are in starch-like powder form and are soluble in water to certain extents. It is desirable to produce insoluble CD-containing particles for adsorption, liquid chromatography and other applications. This work presents a novel method of synthesizing CD-containing resins. Resins synthesized with this method possess high contents of CDs and some favorable physical properties. Adsorption isotherms for three small aromatic compounds, namely phenylalanine, tryptophan and aspartame, were obtained experimentally. [ABSTRACT FROM AUTHOR]

A wild-type A. niger strain was employed as a model to investigate the effect of cell immobilization on extracellular protease secretion during fermentation. A metal-coated pad of polyester latex felt was used to immobilize the cells in shake flasks. Compared with free suspension culture, the maximum specific activity of the extracellular protease from immobilized cells was reduced from 129 units/g to 28 units/g. © Rapid Science Ltd. 1998 [ABSTRACT FROM AUTHOR]