Search

Sorbent pads and films have been commonly used for environmental remediation purposes, but designing their internal structure to optimize access to the entire volume while ensuring cost-effectiveness, ease of fabrication, sufficient strength, and reusability remains challenging. Herein, we report a trimodal sorbent film from recycled polypropylene (PP) with micropores, macro-voids, and sponge-like 3D cavities, developed through selective dissolution, thermally induced phase separation, and annealing. The sorbent has hundreds of cavities per cm2 that are capable of swelling up to twenty-five times its thickness, allowing for super-fast saturation kinetics (within 30 s) and maximum oil sorption (97 g/g). The sorption mechanism follows a pseudo-second-order kinetic model. Moreover, the sorbent is easily compressible, and its structure is retained during oil sorption, desorption, and resorption, resulting in 96.5% reuse efficiency. The oil recovery process involves manually squeezing the film, making the cleanup process efficient with no chemical treatment required. The sorbent film possesses high porosity for effective sorption with sufficient tensile strength for practical applications. Our integrated technique results in a strengthened porous polymeric structure that can be tailored according to end-use applications. This study provides a sustainable solution for waste management that offers versatility in its functionality. [ABSTRACT FROM AUTHOR]

Heavy metal water pollution is a global concern in recent years. Copper is a toxic metal at higher concentrations (> 20 μg /g) and needs to be removed using ion exchanger systems. This study investigates the removal efficiencies of copper by the non-metallic fraction (NMF) waste printed circuit boards (PCBs). The high maximum adsorption capacity of copper by the PCB-derived material after activation with KOH was 2.65 mmol/g, and the experimental isotherm was best correlated by the Temkin model. Finally, this study presents a novel dual site adsorption/ion exchange mechanism, wherein the potassium (from the activation) and calcium (present in the structure) served as ion exchange sites for the copper in the solution. Therefore, this recycling study, focusing on cyclic environmental management, converts a major waste material to an activated ion exchange resin (high capacity) for the removal of copper from wastewater solutions and successfully regenerates the resin for re-use while producing an acidic copper solution for recovery by electrolysius or chemical salt precipitation. [ABSTRACT FROM AUTHOR]

2,4-Dichlorophenoxyacetic (2,4-D) is a toxic herbicide used to control weeds in agricultural sector. However, its residuals in soil and water are harmful for human and aquatic life. Therefore, the aim of this study was to evaluate the photocatalytic degradation of 2,4-D from aqueous solution using the Fe-doped TiO2 nanoparticles in the presence of UV and sunlight irradiation. The nanoparticles were synthesized via a mild hydrothermal process. The characteristics of the synthesized nanoparticles were determined using powder X-ray diffraction, Fourier transform infrared and scanning electron microscopy techniques. The effects of different parameters, including pH, nanoparticle dosage, initial 2,4-D concentration and dopant percentage on the degradation of 2,4-D, were investigated. The results demonstrated that the successfully doped nanoparticles had likely pseudo-spherical morphology. The optimum conditions for photocatalytic degradation of 2,4-D obtained at pH 7, nanoparticle dosage = 0.4 g/l, initial 2,4-D concentration = 10 mg/l, dopant percentage = 1.5% and contact time = 120 min. Under the optimal conditions, the photocatalytic degradation efficiencies of 2,4-D under UV and sunlight irradiation were 65 and 72%, respectively. In addition, the findings showed that 2,4-D degradation efficiency increased with increasing dosage of nanoparticles, while it decreased with increasing initial concentration of 2,4-D and initial pH. Therefore, the Fe-doped TiO2 nanoparticles could be used for the photodegradation of 2,4-D, and it is recommended for the degradation of other organic pollutants from aqueous media especially in tropical areas where a free energy source, i.e., sunlight, is available. [ABSTRACT FROM AUTHOR]

In this study, arsenate (As-V) removal using micellar enhanced ultrafiltration (MEUF) modified by cationic surfactants was studied by a dead-end polyacrylonitrile (PAN) membrane apparatus. The UF membrane has been produced by a phase inversion process. The prepared membrane was characterized and analyzed for morphology and membrane properties. The influence of operating parameters such as initial concentrations of As-V, surfactants, pH, membrane thickness, and co-existing anions on the removal of As-V, surfactant rejection, and permeate flux have been studied. The experimental results show that from the two different cationic surfactants used the CPC (cetyl-pyridinium chloride) efficiency (91.7%) was higher than that of HTAB (hexadecyltrimethyl-ammonium bromide) (83.7%). The highest As-V removal was 100%, and was achieved using initial feed concentrations of 100–1000 μg/L, at pH 7 with a membrane thickness of 150 μm in a dead-end filtration system. This efficiency for As-V removal was similar to that obtained using a cross-flow system. Nevertheless, this flux reduction was less than the reduction achieved in the dead-end filtration process. The PAN fabricated membrane in comparison to the RO and NF processes selectively removed the arsenic and the anions, in the water taken from the well, and had no substantial effect on the cations. [ABSTRACT FROM AUTHOR]

An ion exchange resin, based on the sodium diimidoacetate structure, has been tested for the removal of zinc ions from effluents. After employing three isotherm models, namely, Langmuir, Freundlich and Langmuir-Freundlich to measure and analyse equilibrium isotherms, a series of agitated batch experiments have been carried out to optimise the removal of zinc ions in a two-stage batch system. The first optimisation model involves minimising the total amount of resin required to achieve a specific percentage zinc removal. The second optimisation study involves minimising the total batch contact time to achieve a certain percentage zinc removal. [ABSTRACT FROM AUTHOR]

Excess phosphate in water is known to cause eutrophication, and its removal is imperative. Nanoclay minerals are widely used in environmental remediation due to their low-cost, adequate availability, environmental compatibility, and adsorption efficiency. However, the removal of anions with nanoclays is not very effective because of electrostatic repulsion from clay surfaces with a net negative charge. Among clay minerals, halloysite nanotubes (HNTs) possess a negatively charged exterior and a positively charged inner lumen. This provides an increased affinity for anion removal. In this study, HNTs are modified with nano-scale iron oxide (Fe2O3) to enhance the adsorption capacity of the nanosorbent. This modification allowed for effective distribution of these oxide surfaces, which are known to sorb phosphate via ligand exchange and by forming inner-sphere complexes. A detailed characterization of the raw and (Fe2O3) modified HNTs (Fe-HNT) is conducted. Influences of Fe2O3 loading, adsorbent dosage, contact time, pH, initial phosphate concentration, and coexisting ions on the phosphate adsorption capacity are studied. Results demonstrate that adsorption on Fe-HNT is pH-dependent with fast initial adsorption kinetics. The underlying mechanism is identified as a combination of electrostatic attraction, ligand exchange, and Lewis acid-base interactions. The nanomaterial provides promising results for its application in water/wastewater treatment. [ABSTRACT FROM AUTHOR]