Search

This study investigated the application of electrical resistance tomography (ERT) in characterizing the slurry spatial distribution in cemented granular materials (CGMs). For CGM formed by self-flow grouting, the voids in the accumulation are only partially filled and the bond strength is often limited, which results in difficulty in obtaining in situ samples for quality evaluation. Therefore, it is usually infeasible to evaluate the grouting effect or monitor the slurry spatial distribution by a mechanical method. In this research, the process of grouting cement paste into high alumina ceramic beads (HACB) accumulation is reliably monitored with ERT. It shows that ERT results can be used to calculate the cement paste volume in the HACB accumulation, based on calibrating the saturation exponent n in Archie's law. The results support the feasibility of ERT as an imaging tool in CGM characterization and may provide guidance for engineering applications in the future. [ABSTRACT FROM AUTHOR]

The Southwestern area of Fujian Province in China contains a major metallogenic belt. There have been three major tectonic movements since the Late Paleozoic, and the thrusts here are the main mineral deposits. These occurred between the Early Carboniferous and Late Permian eras. Due to dramatic undulations in the surface and associated complex underground structures, a single geophysical method cannot provide reliable imaging results. This is largely due to difficulties in data acquisition and processing. Seismic exploration provides one example. Using this method, raw shot gathers have a low signal-to-noise ratio because of the undulations in the topography. Furthermore, strong lateral velocity variation makes the migration process exceedingly difficult. This means that interpretations of the resulting reflection seismic profile give rise to uncertainty. For this reason, two-dimensional reflection seismology and controlled source audio-frequency magnetotellurics (CSAMT) electromagnetic sounding techniques were performed. After initially completing conventional processing on the seismic reflection data, subsequent pre-stack depth migration (PSDM) over the rugged topography yielded a much better image. It was able to identify thrust faults and magma intrusions. Then, using CSAMT, inversion was conducted with the same topography as the seismic reflection. By combining the migrated seismic profile, inverted resistivity profile, and borehole data, a vertical geological model was constructed. This proved the existence of an overlapped thrust, and it also indicated the possible presence of deeper mineralization. [ABSTRACT FROM AUTHOR]

The gradient-based optimization methods are preferable for the large-scale three-dimensional (3D) magnetotelluric (MT) inverse problem. Compared with the popular nonlinear conjugate gradient (NLCG) method, however, the limited-memory Broyden–Fletcher–Goldfarb–Shanno (L-BFGS) method is less adopted. This paper aims to implement a L-BFGS-based inversion algorithm for the 3D MT problem. And we develop our code on top of the ModEM package, which is highly extensible and popular among the MT community. To accelerate the convergence speed, the preconditioning technique by the affine linear transformation of the original model parameters is used. Two modifications of the conventional L-BFGS algorithm are also made to get a comparable convergence rate with the NLCG method. The impacts of the preconditioner parameters, the regularization parameters, the starting model, etc., on the inversion are evaluated by synthetic examples for both L-BFGS and NLCG methods. And the real MT Kayabe dataset is also inverted by the inversion algorithms. The synthetic tests show that through our L-BFGS inversion algorithm the similar resistivity models can be obtained with that from the NLCG method. For the real data inversion, the L-BFGS method performs more efficiently and reasonable results could be obtained by less iterations of the inversion process than the NLCG method. Thus, we suggest the common usage of the L-BFGS method for the 3D MT inverse problem. [ABSTRACT FROM AUTHOR]

Magnetotellurics and seismic surface waves are two prominent geophysical methods for deep underground exploration. Joint inversion of these two datasets can help enhance the accuracy of inversion. In this paper, we describe a method for developing an improved multi-objective genetic algorithm (NSGA-SBX) and applying it to two numerical tests to verify the advantages of the algorithm. Our findings show that joint inversion with the NSGA-SBX method can improve the inversion results by strengthening structural coupling when the discontinuities of the electrical and velocity models are consistent, and in case of inconsistent discontinuities between these models, joint inversion can retain the advantages of individual inversions. By applying the algorithm to four detection points along the Longmenshan fault zone, we observe several features. The Sichuan Basin demonstrates low S-wave velocity and high conductivity in the shallow crust probably due to thick sedimentary layers. The eastern margin of the Tibetan Plateau shows high velocity and high resistivity in the shallow crust, while two low velocity layers and a high conductivity layer are observed in the middle lower crust, probably indicating the mid-crustal channel flow. Along the Longmenshan fault zone, a high conductivity layer from ~ 8 to ~ 20 km is observed beneath the northern segment and decreases with depth beneath the middle segment, which might be caused by the elevated fluid content of the fault zone. [ABSTRACT FROM AUTHOR]

We developed a three-dimensional (3D) conjugate gradient inversion algorithm for inverting magnetotelluric impedance tensor measurements. In order to show the importance of including diagonal components of magnetotelluric impedance tensor in 3D inversion, synthetic data were inverted using the 3D conjugate gradient inversion, and the inversion results were compared and analyzed. The results from the 3D inversion of synthetic data indicate that both the off-diagonal and the diagonal components are required in inversions to obtain better inversion results when there are no enough data sites to recover the target resistivity structure. These examples show that lots of information about 3D structure is also contained in the diagonal components; as a result, diagonal components should be included in 3D inversions. The inversion algorithm was also used to invert the impedance tensor data acquired in the Kayabe area in Japan. Inversions with the synthetic and real data demonstrated the validity and practicability of the inversion algorithm. [ABSTRACT FROM AUTHOR]

We implement a parallel algorithm with the advantage of MPI (Message Passing Interface) to speed up the rapid relaxation inversion for 3D magnetotelluric data. We test the parallel rapid relaxation algorithm with synthetic and real data. The execution efficiency of the algorithm for several different situations is also compared. The results indicate that the parallel rapid relaxation algorithm for 3D magnetotelluric inversion is effective. This parallel algorithm implemented on a common PC promotes the practical application of 3D magnetotelluric inversion and can be suitable for the other geophysical 3D modeling and inversion. [ABSTRACT FROM AUTHOR]

Based on the analysis of the conjugate gradient algorithm, we implement a threedimensional (3D) conjugate gradient inversion algorithm with magnetotelluric impedance data. During the inversion process, the 3D conjugate gradient inversion algorithm doesn’ t need to compute and store the Jacobian matrix but directly updates the model from the computation of the Jacobian matrix. Requiring only one forward and four pseudo-forward modeling applications per frequency to produce the model update at each iteration, this algorithm efficiently reduces the computation of the inversion. From a trial inversion with synthetic magnetotelluric data, the validity and stability of the 3D conjugate gradient inversion algorithm is verified. [ABSTRACT FROM AUTHOR]

The features of the faults in the central and northern Tibetan plateau are discussed, based on two super-wide band magnetotelluric (MT) sounding profiles belonging to the INDEPTH (III)-MT project, which were finished between 1998 and 1999: one is from Deqing to Longweicuo (named line 500), the other is from Naqu to Golmud (line 600). This work assists research on the collision and subduction mode between the India and Asia plates. The MT results show that there is a series of deep faults, F1 to F10, in the central and northern Tibetan plateau. Of these faults, F2 is an earlier main fault which leans to the north, and F1 is a later main overriding fault. The Jiali deep fault zone, which has a very complex space structure, is composed of these two faults. F3, F4 and F5 are super-deep faults. They are high-angle faults and lean a little to the south. The main fault zone of the Bangong-Nujiang suture is composed of these three faults. Because of later activity in the structure, several shallow faults formed in the upper crust within the Bangong-Nujiang suture. The Tanggula fault zone is composed of two main faults, F6 and F7, and a series of sub-faults. The shallow segments of the main faults are in high angles and the deep segments of main faults are in low angles. These two faults generally lean to the south and extend into the lower crust. The Jinshajiang suture is composed of the Jinshajiang fault (F8) and the Kekexili fault (F9), and there is a series of sub-faults in the upper crust between these two faults. The Jinshajiang suture is a very wide suture caused by continent-continent collision. The Middle Kunlun fault (F10), which is the main structure of the Kunlun fault zone, is a high angle, super-deep fault. It is the north boundary of the Songpan-Ganzi-Kekexili block. Based on the conductive structure of the profile, the southern part of the Middle Kunlun fault belongs to the Tibetan plateau, but it is not certain whether the northern part of the Middle Kunlun fault belongs to the Tibetan plateau. There are conductive bodies stretching from the crust into the upper mantle below the Bangong-Nujiang suture and Jinshajiang suture. This may suggest heat exchange between the crust and mantle. [ABSTRACT FROM AUTHOR]