Search

During the poultry industrialization process the so-called sludge oil, a residual chicken fat, is recovered in the wastewater treatment plant and its use presents potential as raw material for biodiesel production. Thus, the aim of the study was to prepare blends of sludge oil with soybean oil to obtain fatty acid methyl esters (FAME) through the homogeneous alkaline transesterification reaction. To perform this study, a simple pre-treatment process - heating and subsequent filtration - was used, allowing sludge oil to be mixed with soybean oil to compose blends, without the need to use more sophisticated pre-treatment processes. After this step, blends ranging from 5% to 90% (m/m) of sludge oil mixed with soybean oil were prepared. The results showed that the molar ratio (1:6 oil blend:methanol), catalyst concentration 0.5% NaOH (m cat /m oil ), at 65 °C for 60 min yielded FAME above 99.0 and 90.0% (m/m) for blends with up to 5 and 15% sludge oil, respectively. By increasing the temperature to 70 °C, under the same selected parameters, the blend with 10% sludge oil provided yield above 99.0% (m/m), presenting appropriate physicochemical properties, within the parameters required by National Agency of Petroleum, Natural Gas and Biofuels (ANP). These findings show the great potential sludge oil provides to reduce Brazil's dependency on soybean oil for biodiesel production. Highlights Sludge oil, a waste raw material for biodiesel production, is not yet explored in Brazil.A procedure for biodiesel production using soybean oil and sludge oil blends was proposed.The best reaction condition was 1:6 oil blend:MeOH molar ratio; 0.5% NaOH (m cat /m oil ), at 70 °C for 60 min.Biodiesel yield was higher than 99% (m/m) under optimal reaction conditions.Sludge oil represents a promising waste raw material for biodiesel production.

In this work, the reduction of the moisture content from waste oils by a bentonite-based adsorption process was investigated as an alternative for reuse in energy production. Waste cooking oil (WCO) and waste poultry fat (WPF) were characterised (moisture and viscosity, values of acidity, saponification, and peroxide), as well as bentonite clay adsorbent. The response surface methodology (RSM) was applied to define the best moisture adsorption condition by bentonite-based adsorbent regarding a full factorial experimental design (FFED). In the framework of RSM, the adsorbent mass, oil acidity, and agitation speed were varied in three levels in the range of 1.5-3.0 g, 1-38 mg KOH g oil -1 , and 50-150 rpm, respectively, while the adsorption time was fixed in 24 h. Under the best moisture adsorption condition, kinetic tests were performed in a 1-24 h contact time range, besides performing equilibrium adsorption tests at 5 h contact time. Around 90% moisture removal was attained with 1.5 g adsorbent, acidity value of 1 mg KOH g oil -1, and 50 rpm agitation speed, achieving the equilibrium in 5 h. A multilayer adsorption process, as described by the BET isotherm model, was acting in dried bentonite clay, allowing getting excellent moisture adsorption capacity (∼200 mg water g Bent -1 ). Therefore, moisture removal from waste oils by a bentonite clay-based adsorption process has provided results that are suitable and recommendable for economically viable biodiesel production.

This work focused in the evaluation of Oreochromis niloticus fish scales (FS) as biosorbent material in the removal of Zn from a synthetic effluent based on automotive battery industry effluent and, further, a hybrid neutralization/biosorption process, aiming at a high-quality treated effluent, by a cooperative use of dolomite and FS. For this, a physicochemical and morphological characterization (i.e. SEM-EDX, FTIR, XRD, and TXRF) was performed, which helped to clarify a great heterogeneity of active sites (phosphate, carbonate, amide, and hydroxyl) on the biosorbent; also the inorganic constituents (apatites) leaching from the FS was identified. Biosorption results pointed out to a pH-dependent process due to changes in the functional group's anionic character (i.e. electrostatic interactions), where an initial pH = 3 favored the Zn uptake. Kinetic and equilibrium studies confirmed the heterogeneous surface and cooperative sorption, wherein experimental data were described by Generalized Elovich kinetic model and the favorable isotherm profile by Langmuir-Freundlich isotherm ( q m a x  = 15.38 mg g -1 and 1 / n > 1 ). Speciation diagram of Zn species along with the leached species demonstrated that, for the studied pH range, the biosorption was the most likely phenomena rather than precipitation. Finally, the hybrid neutralization/biosorption process showed great potential since both the Zn concentration levels and the pH reached the legislation standards ( C Zn  = 4 mg L -1 ; pH = 5). Hence, based on the characterization and biosorption results, a comprehensive evaluation of the involved mechanisms in such complex system helped to verify the prospective of FS biosorbent for the Zn treatment from solution, in both individual and hybrid processes.

This work aims to evaluate the adsorption potential of bentonite and sugarcane bagasse clay for the reduction of free fatty acids in cooking oil through batch technique, experimental planning with different operating conditions (temperature, adsorbent mass and agitation). After were carried out kinetic studies and thermodynamic studies. Thus, both adsorbents were characterized by nitrogen dispersion, scanning electron microscopy with coupled energy dispersion spectroscopy. The sugarcane bagasse provided higher reductions compared to the bentonite clay, 58 and 50%, respectively. In the kinetic studies, it was observed that the pseudo-secunda model for both materials. Among the isotherms studied, the Langmuir model was better adjusted for sugarcane bagasse and Freundlich for bentonite clay. Thermodynamic parameters indicated spontaneous and endothermic adsorption at temperatures of 18°C, 20°C and 25°C. Both materials showed an advantageous result with the reduction to the adsorption of free fatty acids in the residual oil, considering that they are low-cost materials, their pre-treatment is simple from the operational point of view and their physical and chemical characteristics are favorable to the adsorption process, sugarcane bagasse contains about 42% hemicellulose, which is a hydroxyl-rich material that attracts the H + ions from the medium.

Since industrial wastes are increasing, the development of studies to find ways for their use is urgent. Waste cooking oil is an important source for the production of biodiesel, one of the main biofuels in Brazil. However, during cooking, the oil undergoes conditions that change its properties and decrease its quality, such as its acidity value. Current research treats waste cooking oil by the adsorption process using rice husk, an agro-industrial waste, and activated carbon to compare results. The potential of the adsorbents to remove free fatty acids in waste cooking oil has been investigated by the batch technique, evaluating different operating conditions of temperature, adsorbent mass and agitation. Adsorbents were characterized by nitrogen physisorption, scanning electron microscope, energy-dispersive spectroscopy and X-ray diffraction. The maximum result obtained for activated carbon at acidity reduction was 63%, using 22.4°C, 169.64 rpm and 3.39 g of adsorbent mass. Already, using the rice husk the percentage of removal was the same, 63% using 22.4°C, 80.36 rpm and 1.61 g of adsorbent, however in shorter times. The results prove that the application of the rice husk for this purpose is advantageous, for being a low-cost material, available on a large scale and that provide results similar to activated carbon.

Sugarcane vinasse is a by-product obtained during ethanol production in sugar-ethanol plants. For each 1 L of ethanol produced approximately 11 L of vinasse are generated. As this residue is obtained in high amounts, it is used as fertilizer in sugarcane crops. However, despite being rich in nutrients, sugarcane vinasse is approximately one hundred times more polluting than domestic sewage, making it an environmental problem. Thus, the aim of the present study was to propose a treatment sequence for sugarcane vinasse and evaluate the possibility of energetic use of the generated sludge in the coagulation/flocculation stage. pH, conductivity, turbidity and decreases in UV/Vis absorption spectra were determined for each treatment step. In addition, the upper calorific value of the generated sludge was also determined, while ash (adsorption treatment) and catalyst (heterogeneous photocatalysis) characterizations were also carried out. At the end of the treatment, initial vinasse turbidity was reduced by 100% and pH and conductivity values were stabilized. The sludge presented a higher calorific value of approximately 3,000 kcal kg -1 and the ash and catalyst displayed favorable characteristics to be applied to the sugarcane vinasse treatment stages.