Search

Carbon steel is one of the most widely used alloys in industrial applications. However, the use of this metal may be limited because of corrosion tendency. Thus, it is necessary to develop methods that inhibit its degradation. One way to inhibit corrosion is to use organic inhibitors. Some organic compounds with heteroatoms inhibit corrosion by forming a protective film. In this study, the corrosion inhibition of carbon steel 1020 in 0.1 mol L-1 hydrochloric acid medium was evaluated. The natural inhibitor used was an aqueous extract of the bark of Persea pyrifolia (PP) plant at concentrations of 2.5, 5 and 10% V / V. The electrochemical response was determined by open circuit potential measurements, electrochemical impedance spectroscopy, and anodic potentiodynamic polarization. Therefore, mass loss was measured, and inhibitory efficiency was evaluated. The best results were observed for the concentration of 2.5% V / V of Persea pyrifolia extract, presenting and inhibition efficiency of 82.5% on the 1020 carbon steel. The electrochemical results indicates that PP extract can be used as green corrosion inhibitor in acidic medium. DOI: http://dx.doi.org/10.17807/orbital.v13i2.1469

Poly(3-alkylthiophenes), P3AT, are organic polymers formed by conjugate structures with conductive properties. Zinc oxide (ZnO) has been used as an electron acceptor in hybrid solar cells because it offers electron transport properties and can be synthesized by methods in which the variation of synthesis parameters allows morphological control. Different ZnO morphologies allow for distinct properties in terms of electronic transport at the interface of solar cells. ZnO particles were synthesized by the co-precipitation method. ZnO films were deposited by spin-coating in Fluorine Tin Oxide (FTO) and then immersed in solutions containing poly (3-hexylthiophene) (P3HT) or poly (3-octylthiophene) (P3OT) polymers. The cell was assembled in the form of a sandwich consisting of: FTO/ZnO,P3AT/Iˉ,I3ˉ/Pt/FTO. UV-vis measurements were performed for bandgap calculation, scanning electron microscopy (SEM), X-ray diffraction (XRD), and J-V curves. The ZnO/P3HT cell presented the best values of J, V and η, indicating an improvement in the electronic transfer processes, with a value of η = 0.56%. DOI: http://dx.doi.org/10.17807/orbital.v13i2.1451

Dye-sensitized solar cells (DSSC) are devices to solar energy conversion, which present low production costs and high photoelectrochemical stability. The aim of this study was to investigate the synthesis of TiO2 by Pechini methodology, using C12H28O4Ti and TiCl3 as precursors, and their application in solar cell sensitized by N719 dye. The characterization techniques employed were Scanning Electron Microscopy (SEM), UV-VIS Spectroscopy, X-ray diffraction (XRD), photochronoamperometry, j-V Curves and EIS plots. The results demonstrated a high crystallinity and surface area to particles obtained with C12H28O4Ti as precursor. The highest photoconversion energy efficiency reached was to TiO2 using C12H28O4Ti with PCE= 4.17±0.13% with photoelectrochemical parameters of jsc= 5.53 ±0.08, Voc= 0.78±0.07 FF=0.58±0.05 and less resistive to charge transport with τe= 53 ms. DOI: http://dx.doi.org/10.17807/orbital.v13i2.1446

In this study, it was investigated the photovoltaic parameters of Dye Sensitized Solar Cells (DSSC) and the thin coating morphology of TiO2 by Doctor Blading and Spin Coating methods, sintered at 450 ºC and 450 ºC with a heating rate of 0.4 ºC s-1, using a natural dye extract from Hibiscus. These properties were studied by scanning electron microscopy (SEM), photochronoamperometry and curves j-V. It was demonstrated that all solar cells produced are photosensitive with an excellent charge injection. The cell with a better energy conversion (jsc = 0.53 mA cm-2; Voc= 0.471 V and FF= 0.518), uniform and flawless morphology was obtained to cell coated by Doctor Blading method, with a heat treatment of 450 ºC/0.4 ºC s-1. DOI: http://dx.doi.org/10.17807/orbital.v10i3.1101