Search

In the tourism industry, the sales of local specialties is an important part, and the package design and integrity of the specialties are very important. This paper first introduced the support vector machine (SVM) algorithm that was used for detecting defects on the surface of paper packages. Then, the design of red wind packages was briefly described, and the simulation experiment was carried out on SVM algorithm using red wine packages with different degrees of surface defects. Proper parameters were tested using the k-fold cross-validation method. The results demonstrated that the properties of paper improved the value of packages and the SVM algorithm had better accuracy than artificial recognition in recognizing different degrees of defects on the surface of packages. In conclusion, this paper describes the application of paper in packages and provides an effective method for the defection of defects on the surface of packages. This study provides an effective references to the improvement of package values and the enhancement of package integrity.

Thermography is a non-destructive technique which uses infrared radiation to obtain the temperature distribution of an object. The technique is increasingly used in the pulp and paper industry. To convert the detected infrared radiation to a temperature, the emittance of the material must be known. For several influencing parameters the emittance of paper and board has not previously been studied in detail. This is partly due to the lack of emittance measurement methods that allow for studying the influence of these parameters.An angle-resolved goniometric method for measuring the infrared emittance of a material was developed in this thesis. The method is based on the reference emitter methodology, and uses commercial infrared cameras to determine the emittance. The method was applied to study the dependence on wavelength range, temperature, observation angle, moisture ratio, sample composition, and sample structure of the emittance of paper and board samples. It was found that the emittance varied significantly with wavelength range, observation angle and moisture ratio. The emittance was significantly higher in the LWIR (Long-Wavelength Infrared) range than in the MWIR (Mid-Wavelength Infrared) range. The emittance was approximately constant up to an observation angle of 60° in the MWIR range and 70° in the LWIR range, respectively. After that it started to decrease. The emittance of moist samples was significantly higher than that of dry samples. The influence of moisture ratio on the emittance could be estimated based on the moisture ratio of the sample, and the emittance of pure water and dry material, respectively.The applicability of measured emittance values was demonstrated in an investigation of the mechanical properties of sack paper samples. An infrared camera was applied to monitor the generation of heat during a tensile test of a paper sample. It was found that the observed increase in thermal energy at the time of rupture corresponded well to the value of the elastic energy stored in the sample just prior to rupture. The measured emittance value provided an increased accuracy in the thermal energy calculation based on the infrared images.

Real time paper surface-web measurement is one of the challenging research fields. The traditional laboratory method has many limitations and is unable to measure the entire tambour during the manufacturing process. It has been necessary to develop an online technique that could measure the surface topography in real time. An optical technique was developed, based on laser triangulation, and is applied to develop a new prototype device, which characterizes high speed paper-web surfaces over a wide scale of spatial wavelengths spectrum and computes the surface roughness in real time. The used multi channel pulsed laser diode, source of illumination onto the paper-web, is of benefit due to its low coherence length and is capable to deliver a powerful burst of light beam over a 1 µs duration, which delivers energy of 100 µJ per pulse. The short exposure time avoids blurriness in the acquired images which could possible due to the high speed and vibrations on the paper-web.The laser beam is shaped into a narrow line-of-light using cylindrical lenses and is projected onto a paper-web surface, which covers a physical length of about 210 mm. The created line-of-light cross section full width at half maximum, FWHM Gaussian distribution, is 2-3 pixels on the image. The line-of-light is projected onto the paper-web perpendicular to the plane of the surface. The low angled, low specular, reduced coherence length, scattered reflected laser line is captured by the 3 CCD sensors, which are synchronized with the laser source. The low specular light ensures to avoid saturation of the imaging sensors if the surface is very smooth, and obliquely captures the z-directional fine feature of the surface.The scattered phenomenon of the reflected light is responsible for the surface irregularity measurements. The basic image processing algorithm is applied in order to remove noise and cropped the images widthwise so that only pixels above a preset threshold gray level can be processed, which enables efficient real time measurement. The image is transformed into a 1D array using the center of gravity, COG. The accuracy and precision of the COG depends on the line-of-light FWHM, which, in turn, is responsible for the accuracy, noise and the resolution of the developed technique. The image subpixel resolution achieved is 0.01 times a pixel and uuncertainty in the raw data is 0.43 µm while it is 0.05 µm in the rms roughness.The signal processing steps combining the B-Spline filter and the filter in the spatial frequency domain were employed in order to separate roughness, waviness, and form and position error in the raw profile. The prototype is designed to measure online surface roughness and to characterize surface in a spatial wavelength spectrum from 0.09 to 30 mm, which is extendable to any required spatial range in order to cover a wide scale surface feature such as micro roughness, macro roughness and waviness. It is proven that exploitation of a simple laser triangulation technique could lead to an improvement in the overall quality and efficiency in the paper and paperboard industries and it can also be of potential interest for the other surface characterization problems.

Time-dependent, stochastic failure is most common in practical situations where paper and board are used, such as web breaks and box failure. A theoretical treatment has been presented, starting from Coleman’s stochastic failure model to the models with structural hierarchy. Creep failure data of box and board published in the literature were analysed from the light of the proposed theoretical model. The results showed that the distribution of life time (not only mean life time) of corrugated boxes changes very sensitively with loading and environmental conditions. Generally the coefficient of variation varied from 6% to 90%. Another important parameter, the load sensitivity of damage growth also varied from 1.7 to 27. Such enormous variation of the key parameters is not a mere fluctuation of experimental condition, but represents the very nature of timedependent, stochastic failure. The stochastic failure model presented provides a framework for analyzing experimental data as well as for predicting life time distributions under general fluctuating loading conditions other than creep.