Search

Measurements of shear wave splitting at 43 three–component seismic stations show very big difference in anisotropy on both sides of the Indus–Yarlung Zangbo suture (ITS), but little difference on both sides of the older Bangong–Nujiang suture (BNS) and the Jinsha River suture (JS) to its north. Obvious discrepancy exists between the anisotropy direction and the superficial tectonic trends, which is not explicable directly by the coherent upper mantle deformation usually supposed to occur in consistency with the trend of a collisional belt. On the other hand, strong spatial relationships are observed from the anisotropy results, such as the orthogonal directions of anisotropy on both sides of ITS and the good correlation between the region of larger magnitude of anisotropy and the zone of inefficient Sn propagation of Qiangtang as well as the systematic rotation of the directions of anisotropy, which should testify some much more complicated aspects of the continental convergence mechanism To the best of our data, we tend to suppose that the Qinghai—Tibet plateau might result from a mechanism complicated by the coexistence of Argand's underthrusting and Dewey's diffuse deformation.

This paper introduces 8 major discoveries and new understandings with regard to the deep structure and tectonics of the Himalayas and Tibetan Plateau obtained in Project INDEPTH, They are mainly as follows. (1) The upper crust, lower crust and mantle lithosphere beneath the blocks of the plateau form a "sandwich" structure with a relatively rigid-brittle upper crust, a visco-plastic lower crust and a relatively rigid-ductile mantle lithosphere. This structure is completely different from that of monotonous, cold and more rigid oceanic plates. (2) In the process of north-directed collision-compression of the Indian subcontinent, the upper crust was attached to the foreland in the form of a gigantic foreland accretionary wedge. The interior of the accretionary wedge thickened in such tectonic manners as large-scale thrusting, backthrusting and folding, and magmatic masses and partially molten masses participated in the crustal thickening. Between the upper crust and lower crust lies a large detachment (e.g. the Main Himalayan Thrust in southern Tibet, 5-8 km thick) or a very thick shear-schistose zone (e.g. the Main Qiangtang Thrust-MQT in northern Tibet, up to 20 km thick), which causes the decoupling of the upper crust and lower crust and separation of tectonic activities. (3) During the collision-compression, the Indian mantle lithosphere was delaminated into two layers from where the crust thickened most rapidly (beneath the High Himalayas). The upper layer extends to 34.5°N and the lower layer to 33.5°. They have been underthrust to depths of 250-300 km into the asthenosphere. Meanwhile the Asian lithosphere (possibly the Qaidam terrane) has also been subducted southwards. Very thick mantle lithosphere does not exist beneath the plateau. (4) The oceanic lithosphere, in light of its lithology and dynamic behaviour, might be close to those of the continental lithosphere and its front might enter the asthenosphere before the continental lithosphere. (5) A 150-200 km deep low-velocity body below 35°N and a wide low-velocity zone below the area between 33.5° and 35°N dip north at very steep angles. Volcanism took place frequently in northern Tibet and anisotropy variations are prominent at depths, which might indicate a zone of large-scale eastward transfer of deep-seated materials.

Numerical simulation of fluid migration during the ore-forming process of the Carboniferous exhalation-sedimentary (Sedex) massive sulfide deposits in the Tongling district shows that fluid and thermal activities in lying-wall rocks were limited to a small area around the main draining passage, which led to weak mineralization and alteration in the lying-wall rock. Temperature and fluid fields indicate that mineralization and alteration in the lying-wall rock of the Sedex-type deposits are usually weaker than those of volcano-hosted massive sulfide deposits. Fluid migration involves the following processes: seawater penetrating and leaching the lying-wall rocks, then mixing with ascending hydrothermal fluids in the main draining passage, and finally jetting into seafloor. Although fluid activity-influenced area is rather small, the content of metals leached out from the lying-wall rocks is high enough to form large-scale ore deposits. Tensional contemporaneous faults accompanied with strong heat flows controlled the formation and distribution of Sedex deposits. The tensional tectonic regime on the northern margin of the Yangtze block during the Hercynian provided Sedex deposits with a prerequisite geodynamic condition.