Search

The double‐sided permanent magnet linear synchronous motor (DS‐PMLSM) is widely used in the industrial field with high precision and long strokes due to simple construction, high instantaneous thrust and high controllability. However, parasitic issues, such as unavoidable manufacturing tolerances, might cause the symmetrical position deviation of primary or secondary components, which results in an asymmetrical air‐gap between components, affecting the motor's electromagnetic characteristics further. In this paper, it is taken into account secondary torsional or offset conditions (the secondary component is displaced sideways from a symmetrical position), and investigates the variations of electromagnetic characteristics on the 12‐solt 14‐pole short‐primary DS‐PMLSM. Based on the finite element method (FEM), the effects of secondary torsion or offset on the air‐gap flux density, the back‐EMF, the detent force, the thrust force, and the normal force are investigated and compared respectively. In addition, the analytical results of the back‐EMF considering lower secondary torsion are verified on a lower secondary torsional prototype. From the analytical results of electromagnetic characteristics, it is revealed that with the torsional angle or offset distance rising, the normal force and detent force in the Y‐axis gradually increase, while the thrust force and the back‐EMF decrease. These theoretical researches can play an important role in the operation and assembly process of the DS‐PMLSM. © 2022 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Fractional slot concentrated winding (FSCW) is a kind of winding structure with few‐slots/coils multi‐poles. FSCW has the potential value of high torque density due to its short end‐winding and high slot fill ratio and is widely used in low‐speed direct‐drive application situations. However, compared with integral slot winding (ISW), the back EMF coefficient of FSCW is smaller, which leads to smaller output torque under the same condition. To improve the back EMF coefficient of FSCW, equidirectional toroidal winding (ETW) is proposed and applied to the dual rotor slotless axial flux permanent magnet motor (AFPM), in which the unit structure is three slots/coils two poles, and the ideal back EMF coefficient is the same as that of ISW. In this paper, firstly, the structure of ETW is introduced and its operating principle is analyzed. Then, compared with the AFPM with ISW, the open circuit and load characteristics of the AFPM with ETW under two conditions of the same wire gauge and the same coil width are analyzed respectively. The back EMF coefficient and output torque of ETW‐AFPM are similar to that of ISW‐AFPM under the same coil width. The back EMF coefficient and output torque of ETW‐AFPM are a little lower than that of ISW‐AFPM under the same wire gauge. Finally, the experimental results also validate the feasibility of AFPM with ETW and the correctness of the analysis results. © 2022 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

In terms of the characteristics of multi‐objective and interactions among optimization objectives of the tubular permanent magnet linear generator with 120° phase belt toroidal winding (120°‐TPMLG), a multi‐objective optimization method is proposed to improve the generators performances, which is based on the combination of response surface method and the genetic algorithm. First, the sensitivity analysis of different structural parameters on the performances of the 120°‐TPMLG is conducted to pick out the sensitive structural parameters. Then develop those sensitive parameters as optimization variables to establish the response surface equation of the generator performances including output power (P), detent force (F), and the efficiency (η). Subsequently, based on the surface equation, the genetic algorithm (GA) fitness function is proposed to conducted the global optimization and the optimization results are finally obtained. To verify the effectiveness of the proposed optimization method, the performances of the optimal 120°‐TPMLG are analysed and compared with the initial one. The results show that the performances including the detent force and power density of the 120°‐TPMLG are greatly improved, which prove that the proposed multi‐objective optimization method is effective for the 120°‐TPMLG. [ABSTRACT FROM AUTHOR]

The three‐phase permanent magnet synchronous motor (three‐phase PMSM) has gained much popularity in many applications due to its various advantages. In addition, due to the good fault tolerance, simple inverter circuit structure and high torque density, the six‐phase PMSM has better prospects than three‐phase PMSM in biomedical devices, electric vehicles and other fields with high reliability requirements. In this study, a six‐phase axial‐flux PMSM inherently without cogging torque is proposed to improve torque density, which equips the 60° phase‐belt toroidal winding (60°TW) and slotless stator core. Based on the same effective volume, permanent magnet material, power grade and the other major motor parameters, two six‐phase PMSMs with 30° phase‐belt toroidal winding (30°TW) and 60°TW are designed, respectively. The armature reaction field, air gap magnetic density, back‐electromotive force, output torque, loss characteristic and torque‐speed characteristic are compared by using three‐dimensional (3D) finite‐element models in detail. Finally, the experimental test is carried out using the prototype of three‐phase PMSM with 120° phase‐belt toroidal winding. The experimental results indirectly verify the feasibility of 60° phase‐belt toroidal winding and correctness of 3D FEM. The 3D FEM analysis results are presented to show that torque density of the proposed six‐phase PMSM with 60°TW is improved in comparison to the six‐phase PMSM with 30°TW. Index Terms—60° phase‐belt toroidal winding, axial flux, six‐phase permanent magnet synchronous motor, torque density [ABSTRACT FROM AUTHOR]