Search

The degradation of two amorphous silicon‐based photovoltaic (PV) modules, namely, of single junction amorphous silicon (a‐Si) and of micromorph tandem (a‐Si/ μ‐Si), after 11 years of exposure in the south of Spain is analyzed. Their I‐V curves were measured outdoors to study the changes of the electrical parameters in the course of three different periods: during the initial days of exposure, during the first year, and in the subsequent 10‐year period. The translation of the curves to an identical set of operating conditions, which enables a meaningful comparison, was done by the different correction procedures described in the standard IEC60891:2021, including the procedure 3, which does not require the knowledge of module parameters, whose values are typically not available. The annual power degradation rates over the entire 11‐year period are 1.12% for the a‐Si module, which is 3.02% for the first year, and 0.98% for the a‐Si/ μ‐Si, which is 2.29% for the initial year. [ABSTRACT FROM AUTHOR]

In this paper, the results of the analysis of the degradation of a set of single‐crystalline silicon modules after 21 years are presented. The comparison of the main electrical parameters and the series and of the shunt resistances measured in 1996 and 2017 is performed, so that the annual degradation rate is evaluated. In addition, a detailed analysis of the parameter uncertainties has been performed in order to determine its impact on the results. A visual inspection of the modules has also been carried out in order to show the correlation with the variation of the electrical performance. Finally, the temperature coefficients of the degraded modules have been estimated and compared with the nominal ones. The results shown in the paper reveal that the mean annual degradation rate in terms of power is close to 0.9%. [ABSTRACT FROM AUTHOR]

In practical photovoltaic (PV) installations the operating conditions of the panels the PV array is made of are different owing to different factors. Such irregular conditions are known as 'mismatching conditions' and produce multiple maxima in the power-voltage curves of any PV array. The traditional maximum power point tracking (MPPT) techniques are able to track one of those maxima, but they cannot guarantee the extraction of the maximum power the PV array would be able to deliver. To overcome this problem, many techniques have been presented in the literature: they use one converter for the entire array (centralised MPPT), one converter for each part of the array (distributed MPPT) or they reconfigure the PV array (RMPPT). This paper presents the general architectures used by 61 different MPPT techniques, by discussing their main advantages and disadvantages, in order to give to the reader a comprehensive view of both the control strategies and the architectures for extracting the maximum power from a mismatched PV field. Moreover, the widely adopted techniques for each hardware structure are presented in a structured and compact way, thus providing to the reader some guidelines regarding the technique's operation principle and hardware requirements. [ABSTRACT FROM AUTHOR]

In practical photovoltaic (PV) installations the operating conditions of the panels the PV array is made of are different owing to different factors. Such irregular conditions are known as 'mismatching conditions' and produce multiple maxima in the power-voltage curves of any PV array. The traditional maximum power point tracking (MPPT) techniques are able to track one of those maxima, but they cannot guarantee the extraction of the maximum power the PV array would be able to deliver. To overcome this problem, many techniques have been presented in the literature: they use one converter for the entire array (centralised MPPT), one converter for each part of the array (distributed MPPT) or they reconfigure the PV array (RMPPT). This paper presents the general architectures used by 61 different MPPT techniques, by discussing their main advantages and disadvantages, in order to give to the reader a comprehensive view of both the control strategies and the architectures for extracting the maximum power from a mismatched PV field. Moreover, the widely adopted techniques for each hardware structure are presented in a structured and compact way, thus providing to the reader some guidelines regarding the technique's operation principle and hardware requirements. [ABSTRACT FROM AUTHOR]

ABSTRACT In this paper, a Distributed Maximum Power Point Tracking (D-MPPT) approach in photovoltaic (PV) applications is discussed. The proposed control method is suitable for the granular control of the PV generator at a module level or even at a sub-module level. D-MPPT is usually implemented by means of independent converters, each one of them running its own MPPT algorithm. Instead, the architecture proposed in this paper consists of only one digital controller, implementing a multivariable MPPT algorithm based on the Perturb and Observe approach, acting on a number of dc/dc converters, each one of them dedicated to a single PV module. The proposed control strategy reduces the number of current sensors with respect to the classical D-MPPT architecture and tracks the maximum power evaluated at the dc/dc converters' output. Planar solid immersion mirror simulations and experimental results confirm the validity of the approach and of the design guidelines proposed in the paper. Copyright © 2012 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]