Search

We propose an electrode-free zinc manganese battery, where both zinc and MnO2 are electro-deposited from the electrolyte via a charging process onto carbon current collectors. The electrode-free batteries show an improved cycling performance of thin-film batteries than the ones with a zinc anode and a facilitated fabrication process for fiber batteries. [ABSTRACT FROM AUTHOR]

The preliminary characterization of thin-film transistors (TFTs) based on a dispersion of ZnO nanorods in an n-type polymer semiconductor, [6, 6]-phenyl-[C.sub.61]-butyric acid methyl ester (PCBM), is reported. The results obtained showed a highly promising enhancement for high-performance solution-processable n-type OTFTs.

The synthesis and applications of semiconducting nanostructures such as zinc oxide (ZnO) nanowires and tungsten disulfide (W[S.sub.2]) nanotubes is reported. The findings from the studies could be used to fabricate the transistors/phototransistors and photovoltaic (PV) energy conversion cells.

• The capacities achieved 0.08 mAh/cm2 for thin-film electrolytic MnO 2 -Zn batteries. • Over 200 cycles were demonstrated for batteries with electrolyte of 25 µL/cm2. • The shuttle reactions caused by iodide mediators were revealed experimentally. Whilst electrolytic MnO 2 with a high capacity draws great attention recently, the shuttle reactions between the mediator additives in the electrolytes with zinc and MnO 2 are often overlooked. In this work, neutral acetate electrolytes with iodide mediator are tested for electrolytic MnO 2 -Zn system on thin-film batteries. With a limited amount of electrolyte, the shuttle reactions caused by iodide mediator becomes more obvious, which results in low Coulombic efficiencies and shortens shelf-life. [ABSTRACT FROM AUTHOR]

Linear wave energy converters generate intrinsically intermittent power with variable frequency and amplitude. A composite energy storage system consisting of batteries and super capacitors has been developed and controlled by buck-boost converters. The purpose of the composite energy storage system is to handle the fluctuations and intermittent characteristics of the renewable source, and hence provide a steady output power. Linear wave energy converters working in conjunction with a system composed of various energy storage devices, is considered as a microsystem, which can function in a stand-alone or a grid connected mode. Simulation results have shown that by applying a boost H-bridge and a composite energy storage system more power could be extracted from linear wave energy converters. Simulation results have shown that the super capacitors charge and discharge often to handle the frequent power fluctuations, and the batteries charge and discharge slowly for handling the intermittent power of wave energy converters. Hardware systems have been constructed to control the linear wave energy converter and the composite energy storage system. The performance of the composite energy storage system has been verified in experiments by using electronics-based wave energy emulators. [ABSTRACT FROM AUTHOR]

We report on the improvement of power conversion efficiency (PCE) of PTB7/PC70BM solar cells by the addition of small quantities (0.02%-0.04%) of pristine single-walled carbon nanotubes (SWNTs) in the active-layer. SWNTs and purified semiconducting SWNTs (S-SWNTs) were added in quantities, which is 2 orders of magnitude lower than previously reported value and resulted in a reduction in the series resistance of the solar cell with minor changes on the shunt resistance. On addition of purified S-SWNT, the PCE of air measured devices enhanced by 29% from 4.9% to 6.3%, with short-circuit current density (JSC) improving from 12.1mA/cm² to 14.4 mA/cm² and a fill factor improvement from 54% to 61%. In addition, the role of processing additive N-Methyl-2-pyrrolidone, which acts as a SWNT dispersant, is also investigated. A single diode model of a solar cell is used to extract the cell parameters and understand the effect of SWNTs. Based on experimental data and it's fitting to the single diode model, we propose that S-SWNT improve the transport and extraction of photogenerated charges within the solar cell device. [ABSTRACT FROM AUTHOR]

Subwavelength nanostructures are considered as promising building blocks for antireflection and light trapping applications. In this study, we demonstrate excellent broadband antireflection effect from thin films of monolayer silica nanospheres with a diameter of 100 nm prepared by Langmuir-Blodgett method on glass substrates. With a single layer of compact silica nanosphere thin film coated on both sides of a glass, we achieved maximum transmittance of 99% at 560 nm. Furthermore, the optical transmission peak of the nanosphere thin films can be tuned over the UV-visible range by changing processing parameters during Langmuir-Blodgett deposition. The tunable optical transmission peaks of the Langmuir-Blodgett films were correlated with deposition parameters such as surface pressure, surfactant concentration, ageing of suspensions and annealing effect. Such peak-tunable broadband antireflection coating has wide applications in diversified industries such as solar cells, windows, displays and lenses. [ABSTRACT FROM AUTHOR]

Arrays of periodic one-dimensional nanomaterials offer tunable optical properties in terms of light–matter interaction which are attractive for designing efficient optoelectronic devices. This paper presents a fabrication of bottom-up grown nanopillar (NP) array solar cells based on n-i-p thin-film amorphous silicon using scaffolds of vertically aligned carbon nanotube (CNT) array. The effects of varying the CNT spacing over the range from 800 to 2000 nm on optical and electrical properties of the solar cells were investigated. The NP solar cell with CNT spacing of 800 nm exhibited ‘moth-eye’ broadband antireflection behavior, showing an average reflectance value lower than 10%. The enhanced optical absorption translated to significant enhancements in photocurrent and quantum efficiency compared to a conventional planar solar cell under low light condition. The open-circuit voltage (Voc) of the NP solar cell was found systematically correlated with the CNT spacing and the illumination condition. The results presented here is of importance for developing high efficiency one-dimensional nanostructured solar cells. [ABSTRACT FROM PUBLISHER]

The possibility of enhancing the frequency performance of electrochemical capacitors by tailoring the nanostructure of the carbon electrode to increase electrolyte permeability is demonstrated. Highly porous, vertically oriented carbon electrodes which are in direct electrical contact with themetallic current collector are produced viaMPECVD growth onmetal foils.Theresulting structure has a capacitance and frequency performance between that of an electrolytic capacitor and an electrochemical capacitor. Fully packaged devices are produced on Ni and Cu current collectors and performance compared to state-of-the-art electrochemical capacitors and electrolytic capacitors.The extension of capacitive behavior to the AC regime (~100Hz) opens up an avenue for a number of new applications where physical volume of the capacitor may be significantly reduced. [ABSTRACT FROM AUTHOR]

Thin-film electronics in its myriad forms has underpinned much of the technological innovation in the fields of displays, sensors, and energy conversion over the past four decades. This technology also forms the basis of flexible electronics. Here we review the current status of flexible electronics and attempt to predict the future promise of these pervading technologies in healthcare, environmental monitoring, displays and human–machine interactivity, energy conversion, management and storage, and communication and wireless networks. [ABSTRACT FROM PUBLISHER]

In this paper, we present experimental results describing enhanced readout of the vibratory response of a doubly clamped zinc oxide (ZnO) nanowire employing a purely electrical actuation and detection scheme. The measured response suggests that the piezoelectric and semiconducting properties of ZnO effectively enhance the motional current for electromechanical transduction. For a doubly clamped ZnO nanowire resonator with radius ∼10 nm and length ∼1.91 µm, a resonant frequency around 21.4 MHz is observed with a quality factor (Q) of ∼358 in vacuum. A comparison with the Q obtained in air (∼242) shows that these nano-scale devices may be operated in fluid as viscous damping is less significant at these length scales. Additionally, the suspended nanowire bridges show field effect transistor (FET) characteristics when the underlying silicon substrate is used as a gate electrode or using a lithographically patterned in-plane gate electrode. Moreover, the Young's modulus of ZnO nanowires is extracted from a static bending test performed on a nanowire cantilever using an AFM and the value is compared to that obtained from resonant frequency measurements of electrically addressed clamped-clamped beam nanowire resonators. [ABSTRACT FROM AUTHOR]

Herein we present an inexpensive facile wet-chemistry-free approach to the transfer of chemical vapour-deposited multiwalled carbon nanotubes to flexible transparent polymer substrates in a single-step process. By controlling the nanotube length, we demonstrate accurate control over the electrical conductivity and optical transparency of the transferred thin films. Uniaxial strains of up to 140% induced only minor reductions in sample conductivity, opening up a number of applications in stretchable electronics. Nanotube alignment offers enhanced functionality for applications such as polarisation selective electrodes and flexible supercapacitor substrates. A capacitance of 17 F/g was determined for supercapacitors fabricated fromthe reported dry-transferred MWCNTs with the corresponding cyclic voltagrams showing a clear dependence on nanotube length [ABSTRACT FROM AUTHOR]

Supercapacitors fill the power and energy gap between electrolytic capacitors and batteries. The energy density for commercial supercapacitors is currently limited to ∼5 Wh kg−1. Enhancing the energy and power density of supercapacitors is of great interest as it would open up a much wider range of applications. In this work, thin film supercapacitors made of random networks of single-walled carbon nanotubes (SWNTs) were enhanced by the use of carbon nanoparticles of a size ideal to fill the pores in the SWNT network. These nanoparticles, termed carbon nanohorns (CNHs), provide a much enhanced surface area, whilst maintaining high permeability and porosity. We demonstrate the hierarchical use of carbon nanostructures in a controlled fashion, allowing an enhancement provided by both types of materials, high power density by the SWNTs and high energy density from the CNHs. SWNT films serve as an ideal template onto which CNHs are deposited, with a good size match, adhesion and charge transfer between particles of a single chemical species. This combination results in an enhanced specific capacitance and a reduced equivalent series resistance (ESR) compared to a capacitor made of either individual component. Additionally, the good binding properties of the hybrid material and the high electrical conductivity of the SWNTs permit the removal of both the binder and the charge collector, paving the way for thinner and lighter supercapacitors. These electrodes allow the fabrication of supercapacitors with novel properties. As an example, we demonstrate a semitransparent supercapacitor. These results demonstrate the possibilities that may be available for the enhancement of electrodes by tailoring and combining relevant materials hierarchically in multiple scales. Much potential remains in further enhancement through tailored hierarchical nanostructuring. [ABSTRACT FROM AUTHOR]

Abstract: We report on a facile low temperature method for the preparation of high surface area, nanostructured α-Fe2O3 (hematite) thin films and their application as photoelectrochemical (PEC) water splitting electrodes. The hematite films are fabricated by thermal oxidation in air of DC sputter deposited iron films at temperatures as low as 255°C. This method results in films with a higher surface area than typically obtained by directly sputtering α-Fe2O3. It is shown that beyond a minimum iron thickness, α-Fe2O3 nanowires result upon thermal treatment in atmospheric conditions. Structural and optical characteristics of the resulting films are analyzed. The oxidation process is studied in detail and correlated to the photoelectrical properties. The Fe films oxidize in stages via Fe-oxide layers of increasing oxidation states. Resulting photoelectrochemical performance of fully oxidized films is a balance between optical absorption and charge collection, which varies with film thickness. The optimum film achieved a net photocurrent density of 0.18mA/cm2 in 1M NaOH at 1.23V vs. RHE under simulated AM1.5 sunlight, amongst the highest values reported for undoped hematite films produced at low temperature. [Copyright &y& Elsevier]

In this paper, we report on the synthesis and applications of semiconducting nanostructures. Nanostructures of interest were zinc oxide (ZnO) nanowires and tungsten disulfide (WS2) nanotubes where transistors/phototransistors and photo-voltaic (PV) energy conversion cells have been fabricated. ZnO nanowires were grown with both high- and low-temperature approaches, depending on the application. Individual ZnO nanowire side-gated transistors revealed excellent performance with a field- effect mobility of 928 cm² /V · s. ZnO networks were proposed for large-area macroelectronic devices as a less lithographically intense alternative to individual nanowire transistors where mobility values in excess of 20 cm² /V · s have been achieved. Flexible PV devices utilizing ZnO nanowires as electron acceptors and for photoinduced charge separation and transport have been presented. Phototransistors were fabricated using individual WS2 nanotubes, where clear sensitivity to visible light has been observed. The results presented here simply reveal the potential use of inorganic nanowires/tubes for various optoelectronic devices. [ABSTRACT FROM AUTHOR]

Highly transparent zinc oxide (ZnO) nanowire networks have been used as the active material in thin film transistors (TFTs) and complementary inverter devices. A systematic study on a range of networks of variable density and TFT channel length was performed. ZnO nanowire networks provide a less lithographically intense alternative to individual nanowire devices, are always semiconducting, and yield significantly higher mobilites than those achieved from currently used amorphous Si and organic TFTs. These results suggest that ZnO nanowire networks could be ideal for inexpensive large area electronics. [ABSTRACT FROM AUTHOR]

Zinc oxide (ZnO) nanowires (NWs) grown on carbon fibers using a vapor transport and condensation approach are used as the cathode of a photoelectrochemical cell. The carbon fibers were obtained by electrospray deposition and take the form of a flexible carbon fabric. The ZnO NW on carbon fiber anode is combined with a “black dye” photoabsorber, an electrolyte, and a platinum (Pt) counterelectrode to complete the cell. The results show that ZnO NW and carbon fibers can be used for photoinduced charge separation/charge transport and current collection, respectively, in a photoelectrochemical cell. [ABSTRACT FROM AUTHOR]

We demonstrate a rechargeable zinc-ion battery with high energy density and cyclability using MnO2 and reduced graphene oxide (MnO2/rGO) electrode. The flexible and binder free electrode, with high MnO2 mass ratio (80 wt% of MnO2), is fabricated using vacuum filtration without any additional additives other than rGO. Compared to batteries with conventional MnO2 electrodes, the Zn–MnO2/rGO battery shows a significant enhanced capacity (332.2 mAh g-1 at 0.3 A g-1), improved rate capability (172.3 mAh g-1 at 6 A g-1) and cyclability. The capacity retention remains 96% after 500 charge/discharge cycles at 6 A g-1. The high MnO2 mass ratio makes MnO2/rGO electrode advantageous when the capacity is normalized to the whole electrode, particularly at high rates. The calculated gravimetric energy density of Zn–MnO2/rGO battery is 33.17 W h kg-1, which is comparable to the existing commercial lead-acid batteries (30–40 W h kg-1). Furthermore, the discharge profile and capacity of our Zn–MnO2/rGO battery shows no deterioration during bending test, indicating good flexibility. As a result, zinc-ion battery is believed to be a promising technology for powering next generation flexible electronics. Zinc-ion batteries: a carbon based promoter Simple carbon materials are shown to modify the MnO2 electrodes and greatly enhance the capacity and cyclability for zinc-ion batteries. An international team led by Prof Hang Zhou from Peking University Shenzhen Graduate School, China developed high performance flexible zinc-ion batteries with MnO2 and reduced graphene-oxide composites as the electrodes. The electrodes are prepared by vacuum filtering the suspension of the mixture of reduced graphene oxide and hydrothermal synthesized MnO2 nanosheets. The incorporation of reduced graphene oxide not only enhances the battery capacity by improving the conductivity and increasing the specific surface area, but also reduces the production cost by saving the trouble to use other binders or additives. Due to above advantages, this approach is competitive for wearable energy storage devices. [ABSTRACT FROM AUTHOR]

This paper presents a flexible, integrated piezoelectric system that is simultaneously designed to operate as a self-powered touch sensor and as a charge pump and storage device for the long-term accumulation of energy over several pressure cycles. Rectification is achieved by stacking a piezoresistive polymer on top of a piezoelectric polymer, so that the conductivity of the former switches in phase with the generation of charge in the latter, upon application and release of stress. A thin flexible electrochemical capacitor is then stacked onto the structure to store the generated charge. The resulting integrated generator proves a robust device of general applicability, featuring a flexible and deformable nature, a large dynamic range, and simple manufacturing. [ABSTRACT FROM AUTHOR]

As a result of their morphology, nanowires bring new properties and the promise of performance for a range of electronic devices. This review looks into the properties of nanowires and the multiple ways in which they have been exploited for energy generation, from photovoltaics to piezoelectric generators. [ABSTRACT FROM AUTHOR]

A dielectric nanocomposite based oncyanoethylatedcellulose (CRS) and MMT nanoclay was successfully prepared with different weight percentages (5%, 10% and 15%) of MMT. MMT nanoplatets obtained via sonication of MMT nanoclay in acetone for a prolonged period was used in the preparation of CRS-MMT nanocomposites. CRS-MMT thin films on SiO 2 /Si wafers are used to form metal-insulator-metal (MIM) type capacitors. At 1 kHz CRS-MMT nanocomposites exhibited high dielectric constants (ε r ) of 71, 55 and 42 with low leakage current densities (10 −6 –10 −7 A/cm 2 ) for nanocomposites with 5%, 10% and 15% weight of MMT respectively, higher than values of pure CRS (21), Na-MMT(10). Reduction of ε r with higher MMT loading can be attributed to a network formation as evidenced via strong bonding interactions between CRS and MMT leading to a lower molecular mobility. The leakage is studied using conductive atomic force microscopy (C-AFM) indicates that leakage pathways are associated with MMT nanoplatelets embedded in the CRS polymer matrix. [ABSTRACT FROM AUTHOR]

We present a stable inkjet printable graphene ink, formulated in isopropyl alcohol via liquid phase exfoliation of chemically pristine graphite with a polymer stabilizer. The rheology and low deposition temperature of the ink allow uniform printing. We use the graphene ink to fabricate counter electrodes (CE) for natural and ruthenium-based dye-sensitized solar cells (DSSCs). The repeatability of the printing process for the CEs is demonstrated through an array of inkjet-printed graphene electrodes, with ∼5% standard deviation in the sheet resistance. As photosensitizers, we investigate natural tropical dye extracts from Pennisetum glaucum , Hibiscus sabdariffa and Caesalpinia pulcherrima . Among the three natural dyes, we find extracts from C . pulcherrima exhibit the best performance, with ∼0.9% conversion efficiency using a printed graphene CE and a comparable ∼1.1% efficiency using a platinum (Pt) CE. When used with N719 dye, the inkjet-printed graphene CE shows a ∼3.0% conversion efficiency, compared to ∼4.4% obtained using Pt CEs. Our results show that inkjet printable graphene inks, without any chemical functionalization, offers a flexible and scalable fabrication route, with a material cost of only ∼2.7% of the equivalent solution processed Pt-based electrodes. [ABSTRACT FROM AUTHOR]