14 results on '"Solovyov, Mykola"'
Search Results
2. Experimental Realization of a Magnetic Cloak
- Author
-
Gömöry, Fedor, Solovyov, Mykola, Šouc, Ján, Navau, Carles, Prat-Camps, Jordi, and Sanchez, Alvaro
- Published
- 2012
- Full Text
- View/download PDF
3. Investigation of Superconductor Uniformity in CC Tapes by Magnetic Field Mapping
- Author
-
Solovyov, Mykola, Šouc, Ján, and Gömöry, Fedor
- Published
- 2012
- Full Text
- View/download PDF
4. Layered Superconductor/Ferromagnet Structures for Magnetic Field Cloaking
- Author
-
Gömöry, Fedor, Solovyov, Mykola, and Šouc, Ján
- Published
- 2014
- Full Text
- View/download PDF
5. Reducing cross-field demagnetization of superconducting stacks by soldering in pairs.
- Author
-
Dadhich, Anang, Li, Shuo, Solovyov, Mykola, Šouc, Ján, Mošat’, Marek, and Pardo, Enric
- Subjects
PERMANENT magnets ,DEMAGNETIZATION ,SOLDER & soldering ,HIGH temperature superconductors ,TORQUE control ,ELECTRIC torque motors - Abstract
Superconducting stacks can be used as strong permanent magnets in several applications. One of their uses is to build light and compact superconducting motors for aviation, where these magnets can be used in the rotor, but they can demagnetize quickly in the presence of cross fields. In this article, we propose a new configuration of soldered stacks face-to-face, which can be constructed by relatively simple joining techniques. Based on numerical modeling of the cross-field demagnetization of stacks of two and 16 tapes, we show that such a sample can withstand around twice as high ripple field amplitudes than isolated stacks. This is due to the increase in the parallel penetration field by around a factor 2. For cross-field amplitudes below this value, a soldered stack can retain higher permanent magnetization than isolated stacks. This method of reducing cross-field demagnetization does not decrease the power or torque rating of a motor, compared to other strategies like the increase in the gap between rotor and stator. [ABSTRACT FROM AUTHOR]
- Published
- 2022
- Full Text
- View/download PDF
6. Design of Magnetic Cloak for an Alternating Magnetic Field With Multilayer ReBCO Insert.
- Author
-
Solovyov, Mykola, Souc, Jan, Kucharovic, Martin, and Gomory, Fedor
- Subjects
- *
MAGNETIC fields , *CLOAKING devices , *SUPERCONDUCTORS , *MAGNETIC shielding , *MAGNETIC nanoparticle hyperthermia , *ENERGY dissipation , *BULK solids - Abstract
Use of superconductors for the shielding of the magnetic field is a common solution nowadays. In case when the magnetic signature of the shielding device matters, forming a magnetic cloak by combining superconductor with ferromagnetic material is a viable option. When considering the operation in alternating magnetic fields the AC loss linked to the delay in phase of the shielding currents represents an important topic. It is well known that the coated conductor (CC) tapes represent a valid alternative to bulk superconducting material when an AC loss reduction appears as a significant requirement. However, the commercially available coated conductors are usually limited to 12 mm width, therefore finding a suitable arrangement of tapes plays a significant role in the magnetic cloak design. We made a set of experiments on two possible arrangements in the superconducting part (helically wound tapes or straight pieces of the tape) and with the total number of layers up to six. For understanding the mechanism of magnetic field penetration inside the cloak the 2D and 3D numerical models were built. Presented numerical models helped in the localization of the cloak component with high energy dissipation. Analysis of the experimental and computation results allow us to formulate some recommendations for the construction of the superconducting part of the magnetic cloak. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
7. Electromagnetic Modeling of Superconductors With Commercial Software: Possibilities With Two Vector Potential-Based Formulations.
- Author
-
Grilli, Francesco, Pardo, Enric, Morandi, Antonio, Gomory, Fedor, Solovyov, Mykola, Zermeno, Victor M. R., Brambilla, Roberto, Benkel, Tara, and Riva, Nicolo
- Subjects
COMPUTATIONAL electromagnetics ,SUPERCONDUCTORS ,IRON-based superconductors ,MAXWELL equations ,SUPERCONDUCTING magnets ,APPLICATION software - Abstract
In recent years, the $H$ formulation of Maxwell's equations has become the de facto standard for simulating the time-dependent electromagnetic behavior of superconducting applications with commercial software. However, there are cases where other formulations are desirable, for example for modeling superconducting turns in electrical machines or situations where the superconductor is better described by the critical state than by a power-law resistivity. In order to accurately and efficiently handle these situations, here we consider two approaches based on the magnetic vector potential: the $T$ - $A$ formulation of Maxwell's equations (with power-law resistivity) and the implementation of a quasi critical state model (QCSM) with a steep $E$ - $J$ relationship limited at $J_{\rm c}$. In this article, we extend the $T$ - $A$ formulation to thick conductors so that large coils with different coupling scenarios between the turns can be considered. We also discuss the QCSM in terms of its ability to calculate ac losses: in particular, we investigate the dependence of the calculated ac losses on the frequency of the ac excitation and the possibility of using quick one-step (instead of full-cycle) simulations to calculate the ac losses. [ABSTRACT FROM AUTHOR]
- Published
- 2021
- Full Text
- View/download PDF
8. Ripple field losses in direct current biased superconductors: Simulations and comparison with measurements.
- Author
-
Lahtinen, Valtteri, Pardo, Enric, Šouc, Ján, Solovyov, Mykola, and Stenvall, Antti
- Subjects
MAGNETIC properties of superconductors ,DIRECT currents ,MAGNETIC energy storage ,CURRENT density (Electromagnetism) ,SOLID state electronics ,ELECTROMAGNETIC fields - Abstract
In several superconducting applications, as, for example, in some supercondcuting generators, motors, and power transmission cables, the superconductor experiences a changing magnetic field in a DC background. Simulating the losses caused by this AC ripple field is an important task from the application design point of view. In this work, we compare two formulations, the H-formulation and the minimum magnetic energy variation-formulation, based on the eddy current model (ECM) and the critical state model (CSM), respectively, for simulating ripple field losses in a DC biased coated conductor tape. Furthermore, we compare our simulation results with measurements. We investigate the frequency-dependence of the hysteresis loss predictions of the power law based ECM and verify by measurements, that in DC use, ECM clearly over-estimates the homogenization of the current density profile in the coated conductor tape: the relaxation of the local current density is not nearly as prominent in the measurement as it is in the simulation. Hence, we suggest that the power law resistivity, used as the local relation between the electric field intensity E and current density J in ECM, is not an intrinsic property of high-temperature superconductors. The difference between the models manifests itself as discrepancies in ripple field loss simulations in very low AC fields with significant DC fields or currents involved. The results also show, however, that for many practical situations, CSM and ECM are both eligible models for ripple field loss simulations. [ABSTRACT FROM AUTHOR]
- Published
- 2014
- Full Text
- View/download PDF
9. Non-uniformity of coated conductor tapes.
- Author
-
Solovyov, Mykola, Pardo, Enric, Šouc, Ján, Gömöry, Fedor, Skarba, Michal, Konopka, Pavol, Pekarčíková, Marcela, and Janovec, Jozef
- Subjects
- *
SUPERCONDUCTING tape , *CRITICAL current density (Superconductivity) , *SCANNING electron microscopy , *MAGNETIZATION measurement , *CARTESIAN coordinates , *ITERATIVE methods (Mathematics) - Abstract
Non-uniformity of superconductor properties, e.g. a critical current reduction close to the edge of a coated conductor (CC) tape could degrade its performance in some power applications. Reliable characterization of such non-uniformity and understanding of its mechanism requires investigation of the character and causes of degradation. In this paper spatial distribution of critical current density across the width of a CC tape is studied. Three different experimental methods allowing estimation of the local current density were utilized for this purpose: (i) magnetic field mapping above the tape through which a DC current is flowing, (ii) measurement of the critical current of separate strips prepared by patterning of the CC tape, and (iii) magnetization measurements of the pieces cut from various positions within the tape width. Very good agreement between the results obtained by these methods was found, showing a reduction of the critical current density at the tape edges with respect to its centre. Moreover, structural investigation by scanning electron microscopy revealed a correlation between the morphology and the critical current density across the tape width. Insertion of such real non-uniform distribution of critical current density into AC loss calculation resulted in a dramatic improvement in the agreement with experimental results. [ABSTRACT FROM AUTHOR]
- Published
- 2013
- Full Text
- View/download PDF
10. A quasistatic magnetic cloak.
- Author
-
Souc, Ján, Solovyov, Mykola, Gömöry, Fedor, Prat-Camps, Jordi, Navau, Carles, and Sanchez, Alvaro
- Subjects
- *
CLOAKING devices , *ELECTROMAGNETIC waves , *MAGNETIC fields , *TECHNOLOGY , *METAMATERIALS , *PERMEABILITY , *PERMITTIVITY - Abstract
Cloaking a three-dimensional object in free space from electromagnetic waves has recently become a theoretical possibility, although practical implementations can only be made in reduced schemes. If static fields are involved, requirements are less restrictive and some practical realizations have been possible. Here we present a third regime between the full wave and the static cases. We experimentally demonstrate that a cloak constructed under the dc conditions can keep cloaking properties for applied magnetic fields oscillating at low frequencies (up to hundreds of Hz). Because electromagnetic technology works at these frequencies, applications of our ideas to present technology are discussed. [ABSTRACT FROM AUTHOR]
- Published
- 2013
- Full Text
- View/download PDF
11. Magnetic Field Mapping Above the Superconducting Tape With Ni-Covered Edges.
- Author
-
Solovyov, Mykola, Vojenčiak, Michal, and Gömöry, Fedor
- Subjects
- *
FERROMAGNETIC materials , *MAGNETIC fields , *MAGNETIZATION , *CRITICAL currents , *FINITE element method , *SUPERCONDUCTORS , *MAGNETIC flux - Abstract
Covering the edges of a Bi-2223/Ag tape conductor by a layer of soft ferromagnetic material has positive impact on its two basic performance characteristics in low magnetic fields: the critical current is improved by ∼20%, and both the magnetization and transport AC loss are reduced. Reasonable theoretical prediction of the critical current in the tape is obtained by a numerical finite-element method: the whole superconducting portion is saturated by the critical current density assumed to be anisotropic and dependent on the magnetic field. However, for the prediction of AC loss the intermediate states with partial saturation of superconductor are also significant. We studied experimentally the development of magnetic field above a common multifilamentary Bi-2223/Ag tape with edges covered by nickel during stepwise change of the transport DC current. Indirect information about the distribution of electrical current and hence the process of magnetic flux penetration and dissipation at changing the value of current can be extracted from these experiments. [ABSTRACT FROM AUTHOR]
- Published
- 2009
- Full Text
- View/download PDF
12. D -Stability of the Initial Value Problem for Symmetric Nonlinear Functional Differential Equations.
- Author
-
Dilna, Natalia, Fečkan, Michal, and Solovyov, Mykola
- Subjects
NONLINEAR differential equations ,INITIAL value problems ,NONLINEAR equations ,FUNCTIONAL differential equations - Abstract
This paper presents a method of establishing the D-stability terms of the symmetric solution of scalar symmetric linear and nonlinear functional differential equations. We determine the general conditions of the unique solvability of the initial value problem for symmetric functional differential equations. Here, we show the conditions of the symmetric property of the unique solution of symmetric functional differential equations. Furthermore, in this paper, an illustration of a particular symmetric equation is presented. In this example, all theoretical investigations referred to earlier are demonstrated. In addition, we graphically demonstrate two possible linear functions with the required symmetry properties. [ABSTRACT FROM AUTHOR]
- Published
- 2020
- Full Text
- View/download PDF
13. A–V formulation for numerical modelling of superconductor magnetization in true 3D geometry.
- Author
-
Solovyov Mykola and Gömöry Fedor
- Subjects
- *
SUPERCONDUCTORS , *MAGNETIZATION , *DENSITY currents , *MAGNETIC fields , *BENCHMARK problems (Computer science) - Abstract
We present the numerical procedure suitable for computing the distribution of electrical currents in a superconductor with geometry extending in all three spatial dimensions when it is exposed to a magnetic field changing in time. Its main advantage is that it solves the problem in terms of vector potential, of the magnetic field. Such an A-formulation is usually the default option for magnetic field calculations in commercial finite element codes. We have used it in the past when a two-dimensional (2D) approximation was found to be sufficient to predict AC losses of single wires, cables, and coils with circular turns. Incorporation of superconductor properties based on the critical state model is straightforward in 2D because the flow of current is restricted to one direction only. The main challenge in extending the method to three dimensions is to cope with the situation when currents could flow in any direction. We have found that assuming that the local current density in a superconductor is always parallel to the local electrical field, and that its modulus is limited by the critical current density, provides sufficient input for accomplishing a new working equation, linking the vector of current density to the time derivative of the magnetic vector potential. Our method successfully passed testing on the benchmark problem of superconducting cube magnetization. It is also used to interpret the magnetization measured on two cylindrical superconducting objects in the transverse field: one was a tube made from bulk BSCCO and the other a REBCO coated conductor tape helically wound on a non-metallic tube. Computed magnetization loops in both cases show good agreement with experiments and confirm the validity of the method. [ABSTRACT FROM AUTHOR]
- Published
- 2019
- Full Text
- View/download PDF
14. Improving the numerical model for high temperature coated conductors using the Hall-probe measurement.
- Author
-
Solovyov, Mykola, Polak, Milan, Vojenciak, Michal, and Gömöry, Fedor
- Published
- 2010
- Full Text
- View/download PDF
Catalog
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.