Search

In the modern aerospace industry, the importance of a lubrication system is self-evident for aero-engines, and the aero-engine bearing chamber return line is an even more challenging environment, as it involves a complex two-phase flow. The designer of the scavenge pipe needs to have an accurate understanding of the flow conditions in the scavenge pipe. This paper establishes a visual scavenge pipe test system. The flow direction was vertical flow, the test temperature was 370 k, and a high-speed camera was used to take high-definition flow photographs, which can observe the three main flow types: bubble flow, slug flow, and annular flow. Code program was created to analyze many pictures taken to obtain the apparent flow rate and perimeter of bubbles in the pipe under different flow conditions and to explore the gas–liquid two-phase flow in the scavenge pipe. A support vector machine (SVM) was used for data regression prediction, and the converted velocities of the gas–oil phases were inputted as eigenvalues to obtain the predicted values of bubble-flow velocity. The bubble-flow analysis prediction model established in this paper has a good prediction effect with root mean square error RMSE = 0.0172, which can more objectively and accurately describe the bubble-flow characteristics in the scavenge pipe. [ABSTRACT FROM AUTHOR]

Copyright of Atomic Energy Science & Technology is the property of Editorial Board of Atomic Energy Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper discusses the extension of an optical liquid film thickness measurement technique to characterize liquid film flow rate in wavy thin liquid film flow. The technique, based on laser refractometry, is used to measure wave height, shape, frequency, and velocity. A two-zone model to process the measured wave characteristics is used to estimate the liquid film flow rate. The method is validated in a falling film facility where easy optical access allows comparisons of the wave velocity measurements with high-speed videos and where the calculated liquid film mass flow rate can be compared with actual measurements. The paper provides a framework for analyzing time-resolved film thickness data using multizone models in more complex liquid film flows, such as in two-phase annular flow. [ABSTRACT FROM AUTHOR]

In this paper, the gas–liquid two-phase flow within a Tesla valve under zero-gravity conditions is numerically studied. Based on the VOF model and the inlet two-phase separation method, the forward and reverse flow patterns and pressure drop changes in a Tesla valve at different inlet velocities were analyzed. At an inlet velocity of 0.1–0.2 m/s, the flow pattern was slug flow, the bubbles were evenly distributed in different positions in the Tesla valve, and the velocity difference between the main pipe and the arc branch pipe was small. When the inlet velocity was 0.4 m/s, the main flow pattern was annular flow, and there was a phenomenon of gas–liquid phase separation through different flow channels, which was related to centrifugal force. At an inlet velocity of 0.6–0.8 m/s, bubbly flow and slug flow coexisted, which was related to the uneven velocity. In the study range, the difference in the forward and reverse pressure drops of two-phase flow was smaller than that of single-phase flow, and the two-phase diodicity decreased first and then increased with the change in inlet velocity, reaching minimum values of 0.78 at 0.2 m/s and 1.44 at 0.8 m/s. [ABSTRACT FROM AUTHOR]

This Special Issue presents papers related to various aspects of hydrodynamics and heat mass transfer in two-phase gas-liquid and gas-dispersed flows in pipes or ducts. Two-phase gas-liquid and gas-dispersed flows are frequently encountered in energy, nuclear, chemical, geothermal, oil and gas and refrigeration industries. In the experimental and numerical studies of swirling flows in an aerial vortex reactor [[7]], it was found that, similar to the case of two rotating liquids, a strongly swirling jet is formed at the reactor axis and the entire flow takes on the structure of a miniature gas-liquid tornado. All of the abovementioned reviews and research papers have demonstrated the importance and usefulness of two-phase gas-liquid and gas-dispersed flow studies, using both measurements and numerical simulations for science and a range of applications. [Extracted from the article]

With the increasing demand for heavy oil, core annular flow (CAF) is an economical method to transport heavy oil, and many researchers have explored the energy-saving aspects of the CAF method. This paper presents a review of CAF energy saving and factors affecting CAF energy saving. Among them, the energy saving of CAF mainly concerns the changes in pressure drop and drag reduction efficiency; the factors affecting the energy saving of CAF mainly concern the problem of stability, the issue of restarting the pipeline system, the impact of a nozzle, the impact of fouling on the flow in the pipe, and the problem of oil–water accumulation. The aim of this paper is to provide a reference for the practical application of CAF in heavy oil transportation. [ABSTRACT FROM AUTHOR]

Gas flexible pipes are critical multi-layered equipment for offshore oil and gas development. Under high pressure conditions, small molecular components of natural gas dissolve into the polymer inner liner of the flexible pipes and further diffuse into the annular space, incurring annular pressure build-up and/or production of acidic environment, which poses serious challenges to the structure and integrity of the flexible pipes. Gas permeation in pipes is a complex phenomenon governed by various factors such as internal pressure and temperature, annular structure, external temperature. In a long-distance gas flexible pipe, moreover, gas permeation exhibits non-uniform features, and the gas permeated into the annular space flows along the metal gap. To assess the complex gas transport behavior in long-distance gas flexible pipes, a mathematical model is established in this paper considering the multiphase flow phenomena inside the flexible pipes, the diffusion of gas in the inner liner, and the gas seepage in the annular space under varying permeable properties of the annulus. In addition, the effect of a variable temperature is accounted. A numerical calculation method is accordingly constructed to solve the coupling mathematical equations. The annular permeability was shown to significantly influence the distribution of annular pressure. As permeability increases, the annular pressure tends to become more uniform, and the annular pressure at the wellhead rises more rapidly. After annular pressure relief followed by shut-in, the pressure increase follows a convex function. By simulating the pressure recovery pattern after pressure relief and comparing it with test results, we deduce that the annular permeability lies between 123 and 512 mD. The results help shed light upon assessing the annular pressure in long distance gas flexible pipes and thus ensure the security of gas transport in the emerging development of offshore resources. [ABSTRACT FROM AUTHOR]

Understanding droplet sizes is crucial for modeling gas–liquid annular flow and has many applications across various industries. This paper presents a comprehensive review and analysis of experimental data on droplet-size characteristics in gas–liquid annular flow from the open-source literature. The existing models for droplet-size predictions are evaluated against experimental data. Based on the data analysis, we propose two new correlations to predict the maximum droplet diameter and Sauter mean droplet diameter. Model evaluation and parametric study show that the new correlations capture the effects of fluid properties and flowing conditions on the droplet diameters well, outperforming other existing models. The average absolute relative errors are reduced to 14.8% and 29% for the maximum droplet diameter and the Sauter mean droplet diameter, respectively. [ABSTRACT FROM AUTHOR]

A cyclone separator holds significant importance as the primary gas–solid separation apparatus in the industrial sector. Cyclone separators operate based on a fundamental principle, primarily harnessing the centrifugal force produced by the rotation of air in order to segregate solid particles from the gas stream and then collect them. In addition to the main vortex in the flow field, there are a number of secondary flows, which significantly impact the aggregation of fine particles and contribute to the heightened energy consumption. This paper provides a summary of the three secondary flows in a cyclone separator. These include the recirculation flow in the annular space, which is greatly influenced by the inlet particle concentration. Additionally, the short-circuit flow occurs beneath the vortex finder as a result of the collision between the incoming flow and the rotating flow. Furthermore, the eccentric circumfluence is defined as the deviation of the rotation center caused by the interaction between the upward and downward flows near the discharge. This paper aims to establish a theoretical framework to investigate the flow pattern tracking and the mitigation of secondary flows in order to enhance the operational efficiency of cyclone separators. [ABSTRACT FROM AUTHOR]

Modern laver fluffiness is achieved by applying high-speed gas to a laver, which is generated by the opening and closing of a laver fluffiness control valve in a fluffiness system. To address the problems of the slow response speed and poor stability of valves used in the laver processing industry at present, this paper proposes a novel principle of a high-speed switching control valve, which has the advantages of a fast response speed, high stability, and long service life. The structure and working principle of the control valve are introduced, and the calculation equation of the valve's flow area is established. The flow field inside the control valve with different openings was numerically calculated in this study using Fluent. The flow regulation characteristics and flow field performance of the control valve were also analyzed. The results show that, with an increase in the valve opening, the influence of the flow area at the valve throttle on the valve flow rate was weakened. When the valve was opened, a vortex appeared in both the upper and lower cavities, and jet flow occurred at the throttle of the middle flow channel. As the valve opening increased, the pressure in the upper cavity reduced, while the pressure in the lower cavity increased. The vortex in the flow field intensified, and the jet phenomenon at the valve throttle gradually disappeared. At the same time, the main stream in the lower cavity gradually changed from an annular flow to a direct flow toward the valve outlet. Furthermore, the impact, collision, and vortex formation of the fluid caused energy loss of the fluid, leading to a decrease in the outlet flow of the control valve. [ABSTRACT FROM AUTHOR]

Based on the differential quadrature procedure (DQP), the vibrational response of functionally graded (FG) sandwich annular plates enhanced with graphene platelets (GPLs) and with an FG porous core is illustrated in this paper. The current annular plate is assumed to deform axisymmetrically and expose to a radial magnetic field. The Lorentz magnetic body force is deduced via Maxwell's relations. The effective physical properties of the upper and lower layers of the sandwich plate are obtained by employing the Halpin–Tsai model. Our technique depends on a new four-unknown shear deformation theory to depict the displacements. In addition, the motion equations are established via Hamilton's principle. The motion equations are solved by employing the DQP. In order to study the convergence of the DQ method, the minimum number of grid points needed for a converged solution is ascertained. In addition, the current theory's outcomes are compared with those of previous higher-order theories. The effects of the porosity distribution type, porosity factor, GPLs distribution pattern, GPLs weight fraction, inner-to-outer radius ratio, outer radius-to-thickness ratio, magnetic field parameters, core thickness, and elastic substrate parameters on the nondimensional vibration frequencies are discussed. [ABSTRACT FROM AUTHOR]

This paper investigates non-invasive techniques for annular two-phase flow analysis, focusing on liquid film characterization to understand the interfacial phenomena that are crucial for heat and mass transfer. Limited methods allow the study of the temporal and spatial evolution of liquid film, such as Planar Laser-Induced Fluorescence (PLIF). However, this method possesses optical challenges, leading to the need for improved techniques to mitigate refraction and reflection, such as Refractive Index Matching (RIM). This study utilizes an experimental annular flow facility to analyze both RIM and non-RIM PLIF over a range of liquid Reynolds numbers from 4200 to 10,400. Three configurations—PLIF RIM90, PLIF RIM40, and PLIF nRIM40—are compared from both qualitative and quantitative perspectives. In the quantitative analysis, key variables of the liquid film are measured, namely mean film thickness, disturbance wave height, and frequency. Variations in the analyzed variables indicate minor deviations, which are not likely to be caused by the technique used. However, all three methodologies exhibited errors that are estimated to be within a maximum of 10%, with a mean value of approximately 8%. [ABSTRACT FROM AUTHOR]

It is of great significance to explore the flow velocity characteristics of piped cars when they are started under different loads. In this paper, the flow velocity characteristics of the water flow around a piped car when it is started in the straight pipe section are studied through physical experiments. The masses of the piped cars are 1.5 kg, 1.9 kg, and 2.3 kg, respectively. The results show that, with the increase in the load of the pipeline car, the axial flow velocity in the front section increases, the absolute values of radial flow velocity and circumferential flow velocity increase, and the gradient of flow velocity increases. The positive radial flow velocity and negative circumferential flow velocity regions increase, and the distribution of positive and negative radial flow velocities and circumferential flow velocities is obvious. The gradients of axial, radial, and circumferential flow velocities in the annular section all increase, and the contour spacing becomes smaller and more densely distributed. The absolute values of the radial and circumferential flow velocities increase. The regional demarcation of axial flow velocity in the rear section is more obvious, and the average value of axial flow velocity in the high-flow-velocity area behind the vehicle increases. Additionally, the gradient of flow velocity increases. The absolute values of radial velocity and circumferential velocity increase, the gradient of velocity increases, and the velocity distribution is obviously regional. This study supplements and improves the theoretical study of a piped car when it is started and has certain reference value for the research and application of the hydraulic transport technology of the barrel-loading pipeline. [ABSTRACT FROM AUTHOR]

The hydraulic transportation of piped capsules is a new and energy-saving transportation mode, which is especially suitable for the long-distance and high-stability requirements of material transportation. In this paper, the COMSOL Multiphysics software was used to construct a mathematical model of the dynamic characteristics of a piped capsule moving in a straight pipeline, in which the boundary conditions were redeveloped, the inlet velocity distribution function was defined, and the physical experiment was carried out for verification. The dynamic characteristics were analyzed, and through the calculation of the energy consumption, the optimal piped capsule under the research conditions was obtained. The results show that the simulation results and experimental results for the piped capsule's average moving velocity, axial velocity, and wall shear stress along the cylinder wall were basically consistent, with a maximum error of 14.22%, 2.62%, and 20.13%, respectively. With a decrease in the diameter-to-length ratio of the piped capsule, the axial velocity of the concentric annular gap flow decreased gradually. The area with a large shear stress was mainly concentrated at the front and rear ends of the cylinder wall, especially the rear area of the support feet of the piped capsule. With the increase in the diameter of the piped capsule, the wall shear stress of the capsule increased. Finally, the superior diameter-to-length ratio for the piped capsule under the research conditions was obtained and shown to be ε = 0.4. The research in this paper will provide a theoretical reference for the structural design and dynamic mechanism analysis of the piped capsule. [ABSTRACT FROM AUTHOR]

Mass, energy, and momentum transfer processes between fluid-saturated porous media and the adjacent free flow occur in many natural and technical systems. The flow dynamics in the porous region and the adjacent free flow is strongly controlled by the mechanisms at the common interface and conditions on the outer surface of the free-flow. The present paper considers unsteady axisymmetric flows of viscous fluids through an annular domain with a porous layer covering a cylindrical solid core. Fluid flow in the domain filled with porous material and in transparent domain is described by Brinkman model and Navier Stokes equations, respectively. Analytical solutions for the dimensionless velocity fields in the Laplace domain are determined using Bessel functions, Laplace transform, and the appropriate interface and boundary conditions. The inversion of the Laplace transforms is done with the help of a numerical algorithm. In addition, the hydrodynamic permeability is determined. The dependence of the dimensionless velocity fields and of hydrodynamic permeability on characteristic parameters of the porous layer is numerically and graphically discussed. Since the velocity on the outer surface is given by an arbitrary function of time, the results in this paper could be used to study various filtration problems. [ABSTRACT FROM AUTHOR]

The study of the annular slit flow field is important for energy consumption, transport efficiency, and the force on the capsule for hydraulic capsule transportation. A combination of physical experiments and theoretical analysis was used to study the annular flow field around a capsule that was set in motion at different positions of a horizontal bend pipe. We study the flow velocity distribution of the gap flow field at different bend positions of the capsule by changing the position of the capsule at the bend. We found that the distribution of the flow field remained similar for different starting positions of the capsule, but the flow velocity increased suddenly and dramatically at the inflow section of the ring gap. We recorded different velocity distributions of the annular gap on the concave and convex sides of the pipe; on the convex side, the streamline of the gap was smooth, and the change in velocity was relatively small. The flow velocity of the slit flow varied more notably on the concave side of the pipe, and there was a greater fluctuation in the flow velocity distribution. Because the effects of the capsule and the pipe on water flow were not the same, we found large fluctuations in gap flow velocity at different measuring points on the concave side. Gap flow velocity was most influenced by axial flow velocity. We found that the axial flow velocity was about one order of magnitude greater than the radial flow velocity or circumferential flow velocity. In this paper, we analyze the changes in the ring gap flow field of the capsule at different bending positions and analyze the reasons for the flow field changes and the flow velocity distribution law. This is of great significance to the study of the transport efficiency and energy consumption of the capsule. The results of this paper complement the study of capsule initiation at different positions in the bend and provide a reference point in terms of transport efficiency, energy consumption, and capsule stress. The results of this study promote the development of hydraulic capsule transportation. [ABSTRACT FROM AUTHOR]

Microchannel flow boiling is an efficient cooling method for high-heat-flux electronic devices. To understand the flow boiling regime in a T-shaped microchannel, this paper prepared T-shaped microchannels of different sizes and designed an experimental platform for the visualization of flow boiling in microchannels, and aimed to study the evolution characteristics of two-phase flow patterns in T-shaped microchannels. The influences of the flow rate and channel size on the boiling flow pattern inside a T-shaped microchannel were experimentally observed and quantitatively described. The results indicate that the occurrence position of the vaporization core gradually migrates from branch channel to main channel as the wall temperature increases. The flow boiling at the bifurcation of the T-shaped microchannel mainly includes the extrusion fracture flow, bubble flow, plug–annular alternating flow and annular flow, in which the annular flow can be further divided into the intermittent annular flow and the stable annular flow. In addition, a high flow rate and small channel size can lead to the disappearance of the bubble flow, and the presence of the bubble flow delays the appearance of the annular flow. [ABSTRACT FROM AUTHOR]

The spacer represents an essential part in the nuclear fuel rod. Spacer grid with mixing vanes in fuel rod bundle of nuclear reactor core has a significant impact on heat transfer performance in downstream to grid spacer. Grid Spacers are located on the nuclear fuel rod assembly to hold suitable clearance among the rods in a bundle. The objective of this paper is to study the enhanced heat transfer performance of R134a at supercritical pressure 4.5 MPa near downstream to mixing vane spacer in a vertical channel of annular flow. A spacer of 0.38 blockage ratio with mixing vanes, situated at mid-span of an annular channel is used in the present work. Numerical simulations have been accomplished for spacer with mixing vane and spacer without mixing vane in an annular channel by using commercial CFD (Computational fluid dynamics) code ANSYS Fluent. The present investigation represents the comparative study for spacer with mixing vane and spacer without mixing vane effects on heat transfer and flow field characteristics in a downstream direction for mass flow-rate 0.41469 kg/s and heat flux 160 kW/m². The results indicate that spacer with mixing vane has notable influence on heat transfer performance and flow field characteristics downstream of mixing vane spacer as compared to spacer without mixing vane. Wall temperature fall and increase of coefficient of heat transfer are significantly greater adjacent to spacer downstream. Spacer influence in the improvement of the heat transfer is noted up to distance X/D = 40 downstream and then flow is found as fully developed. [ABSTRACT FROM AUTHOR]

Different techniques are used to analyze annular flow, but the more interesting ones are those techniques that do not perturb the flow and provide enough resolution to clearly distinguish the interfacial phenomena that take place at the interface, especially the disturbance waves (DW) and the ripple waves (DW). The understanding of these events is important because it influences the heat and mass transfer taking place through the thin film formed near the walls in this flow regime. The laser-induced fluorescence (LIF) and the three-electrode conductance probe are two commonly used techniques to study experimentally annular flow phenomena. In this paper, a set of experiments at different temperatures of 20 °C, 30 °C and 40 °C and different liquid Reynolds numbers have been performed in the annular flow regime, the characteristic of the DW and RW as average height and frequency of these waves has been measured by both techniques LIF and conductance probes. In addition, we also measured the mean film thickness. It was found that the mean film thickness and the DW height are practically the same when measured by both techniques; however, the height of the RW is smaller when measured by the conductance probe and this difference diminishes when the temperature increases. [ABSTRACT FROM AUTHOR]

Two-phase annular flow in vertical pipes is one of the most common and important flow regimes in fluid mechanics, particularly in the field of building drainage systems where discharges to the vertical pipe are random and the flow is unsteady. With the development of experimental techniques and analytical methods, the understanding of the fundamental mechanism of the annular two-phase flow has been significantly advanced, such as liquid film development, evolution of the disturbance wave, and droplet entrainment mechanism. Despite the hundreds of papers published so far, the mechanism of annular flow remains incompletely understood. Therefore, this paper summarizes the research on two-phase annular flow in vertical pipes mainly in the last two decades. The review is mainly divided into two parts, i.e., the investigation methodologies and the advancement of knowledge. Different experimental techniques and numerical simulations are compared to highlight their advantages and challenges. Advanced underpinning physics of the mechanism is summarized in several groups including the wavy liquid film, droplet behaviour, entrainment and void fraction. Challenges and recommendations are summarized based on the literature cited in this review. [ABSTRACT FROM AUTHOR]

This study examines the suppression of liquid slugs in the transport and separation of multiphase flows in pipelines. Two well‐known slug control approaches are evaluated in this paper. The methods are employed to control and stabilize an undesired and unstable flow regime, optimize flow production, reduce operating costs, and in general, improve overall safety requirements of oil and gas pipelines. Unlike designs with an additional flowline to separate gas upstream, this study shows that active topside choking can suppress slugs and stabilize the system flowrates and pressures without the requirement of separation upstream of the topside valve. Careful choking is required to minimize production losses that can result from excess back pressure. A riser‐based, gas‐lift method reduces system instability and increases production. This study also reveals that negligible improvement in stability is achieved when large volumes of gas are injected. The system shifts into an annular flow regime when the injection is further increased. A large separator may be required to accommodate high gas volumes. This study shows that gas‐lift not coordinated with choking is not effective for slug mitigation through pipeline bends. This paper also presents and discusses new non‐dimensional correlations, including slug control inputs in the pipelines such as choke openings, based on new experimental data. [ABSTRACT FROM AUTHOR]

In order to investigate the recycling technology for efficiently recovering low-temperature wastewater waste heat from industrial production, we built an experimental device for forced boiling heat transfer in an annular tube. This paper takes a ring casing evaporator with an inner tube diameter of 30 mm, a length of 1450 mm, a wall thickness of 0.8 mm, and an outer tube diameter of 14.2 mm, which was used as the main object of study. We conducted experimental research on heat transfer in single-phase liquid flow and two-phase boiling phase change within annular tubes by varying the inlet circulating hot water temperature (60–85 °C), the mass flow rate of the circulating mass (0.85, 1.27, 1.69 kg m−2 s−1), and the inclination angle (0°–90°). The research results indicate that the heat transfer coefficient of boiling phase change within annular sleeves is significantly enhanced compared to convective heat transfer of single-phase liquid flow within annular tubes. This signifies that employing heat pipe technology for waste heat recovery can achieve highly efficient heat transfer processes. This study also reveals that with an increase in the inclination angle, the heat transfer coefficient on the boiling surface follows a trend of initial increase followed by a decrease. Near an inclination angle of 30° within the annular jacket tube, the heat transfer coefficient of two-phase boiling phase change reaches its maximum value. The findings of this study provide certain theoretical guidance for the application of heat pipe energy-saving technology in the field of medium- and low-temperature waste water recovery and utilization. [ABSTRACT FROM AUTHOR]

The stable transportation of pulverized coal in the vertical pipe is significant for the operation of the gasifier. There are few studies on the flow characteristics and flow pattern transition of particles in vertical pipes with small diameters. This paper has modeled and analyzed the flow characteristic of powder in dense-phase pneumatic conveying through 25 mm vertical pipe using CFD. Firstly, the grid independence is verified to determine the optimal mesh size. Then, the influences of different solid loading ratios (SLRs) and conveying velocities on particle flow characteristics, flow stability, and flow pattern transition are investigated. The results show that the flow pattern in the vertical pipe changes from annular flow to uniform flow at high SLR and low conveying velocity. Moreover, the evolution regulation of resistance characteristics under different conveying velocities is further revealed. Considering the conveying stability and economic benefit, the most suitable conveying velocity is 6 m/s. [ABSTRACT FROM AUTHOR]

Water production in the bottom hole is a frequent occurrence during gas drilling, posing a significant threat to the safety of the process. Obtaining the water flow rate quickly is critical to making further engineering decisions. This paper proposes a rapid calculation method of water flow rate based on the principle of pressure drop. The method can quickly identify the multiphase flow pattern and calculate the flow pressure drop, thereby establishing the relationship between the gas injection pressure and the water flow rate. At the gas drilling site, the gas injection pressure is continuously monitored in real-time, which enables rapid acquisition of the real-time water flow rate. The concept of ultimate water-carrying kinetic energy is introduced, which combined with the boundary of annular flow to other flow patterns, can determine the maximum water-carrying flow rate. The feasibility of this method is validated using the field-measured data of well X8-3. [ABSTRACT FROM AUTHOR]

The efficiency of annular-nozzle ejectors serving as components of complex technical systems interacting with high-temperature media in engines and in the field of energy technologies is not linearly related to the gas-dynamic characteristics of the flows formed in the device. In this paper, we have analyzed the results of numerical and experimental studies of gas jets in an annular-nozzle air ejector. The regression equations built according to the circumscribed central composite design described the relationship between a pressure drop and the structural parameters of the nozzle with the speed and mass flow rates of the airflows, including error rates of no more than 15 percent. A two-factor optimization based on Harington's generalized desirability function was performed to obtain a relatively accurate estimate of the ejector efficiency under the influence of the structural and operating parameters. An optimization method based on the combination of response surface methodology and the desirability function approach, allowing simultaneous consideration of all responses, made it possible to simultaneously optimize multiple conflicting objectives. [ABSTRACT FROM AUTHOR]

As an advanced flexible dynamic sealing technology, the leakage characteristics of a finger seal (FS) is one of the key research areas in this technology field. Based on the fractal theory, this paper establishes a mathematical model of the FS main leakage rate considering the fractal wear effect by taking into account the influence of the wear height on the basis of the eccentric annular gap flow equation. Based on the Hagen-Poiseuille law and the fractal geometry theory of porous media, a mathematical model of the FS side leakage rate considering the fractal porous media seepage effect is developed. Then, a mathematical model of the FS total leakage rate is established. The results show that the mathematical model of the FS total leakage rate is verified with the test results, the maximum error rate is less than 5%, and the mathematical model of the FS total leakage rate is feasible. With the gradual increase in working conditions and eccentricity, the FS main leakage rate gradually increases. In addition, the effects of the fractal dimension, fractal roughness parameters and porosity after loading on the FS main leakage rate are negligible. As the fractal dimension of tortuosity after loading gradually decreases, the fractal dimension of porosity after loading gradually increases, and the FS side leakage rate gradually increases. As the porosity after loading gradually increases, the FS side leakage rate gradually increases. Under different working conditions, different fractal characteristic parameters and different porosities after loading, the weight of the FS main leakage rate is much greater than that of the FS side leakage rate by more than 95%. [ABSTRACT FROM AUTHOR]

Annular pressure has been recognized as one of the most challenging problems in the petroleum industry, posing a series of threats to wellbore integrity. Annular pressure caused by thermal expansion during the cement hydration process is rarely studied by researchers. In light of the hydration heat generation process, a kinetics model for cement hydration under different curing temperatures is demonstrated in this paper. Considering interactions between temperature and cement hydration, a transient temperature prediction model during well cementing is built. On the basis of these assumptions, the prediction model of annular pressure is established, considering the change in cement temperature and the change in annulus volume. Using the models illustrated in this paper, a series of numerical simulations are performed. The changing roles of transient cement hydration degree and temperature in wellbores are analyzed thoroughly. The annular pressure during well cementing shows a rapid increase and then a decrease, which is similar to that of the temperature. In addition, a sensitive analysis of annular pressure is conducted. The analysis shows that the annular pressure increases with the geothermal gradient, the cement hydration heat, and the wellbore diameter. Suggestions and conclusions can provide safety guidance for the management of annular pressure during well cementing. [ABSTRACT FROM AUTHOR]

The paper respectively investigated the heat transfer characteristics of molten salt flowed in shell-and-tube and double-pipe steam generator. The shell-and--tube steam generator had seven tubes and molten salt flowed outside the tubes, while the double-pipe steam generator had two concentric tubes and molten salt flowed in the annular duct formed by two tubes. Inlet temperature of molten salt ranged from 270 °C to 420 °C. The experimental results showed the effect of temperature on heat transfer coefficient was more significant in the double-pipe steam generator compared to the shell-and-tube steam generator. The heat transfer coefficient firstly increased and then decreased as the increase of temperature. Further numerical study was conducted and the results showed, in the shell-and-tube steam generator, the flow is disturbed by the tube bundle and the boundary-layer near the inner wall is deformed, so the temperature of molten salt cannot obviously affect the heat transfer. In the double-pipe steam generator, an opposite flow was generated in the near cooled wall region by the buoyancy force. When the inlet temperature was below 315 °C, the velocity of the opposite flow was quite low. In this stage, the heat transfer coefficient increased with the increase of temperature. When the inlet temperature continues to rise to 390 °C, the opposite flow was enhanced and a stable layer with low velocity formed between the mainstream and the inner cooled wall, resulting increase of heat transfer resistance and impairment of heat transfer coefficient. [ABSTRACT FROM AUTHOR]

The aim of this paper is to propose an efficient numerical scheme to deal with heat transfer problems in pipe flow with a large length/diameter ratio. The generalized finite difference method (GFDM) is combined with a space stepping algorithm (SSA) for the solution. The SSA divides the solution domain into a number of overlapping sections in the length direction of the pipe. Due to the large Peclet number, the heat transport process is dominated by advection, which allows an approximate boundary condition to be applied at the downstream cross section. The problem is then solved section by section. Using the uniform distributed points, the solution matrix for each section does not change, and only the right hand side needs to be refreshed for the changing boundary conditions. This leads to a highly efficient scheme for problems with a large pipe length. To show the accuracy of the numerical scheme, a problem with available analytical solution is studied. Then the method is applied to problems of single pipe with different pipe wall temperature and flow Reynolds number, and concentric annular pipe. Numerical results confirm the stability and efficiency of the GFDM-SSA. The method can be applied to many real world transient heat transfer problems in which the pipe is heated or cooled along its length with arbitrary wall temperature for heat exchange and other purposes. [ABSTRACT FROM AUTHOR]

This paper presents a method for machining an annular groove on the inner wall of a steel tube by ball spinning. Based on spatial analytic geometry theory and assumptions about radial helical feed, the process utilizes a simplified expression of boundary curves of radial and tangential contact area between ball and workpiece. Through curve integration, the equations of radial and tangential contact areas for calculating ball-spinning force have been obtained. Based on results from calculation examples, this paper discusses the relationships between spinning depth, ball diameter, spinning feed, and ball-spinning force. The comparison of calculation results between the analytical model and the finite element method has been supplied, and the validity of the model has been certified. [ABSTRACT FROM AUTHOR]

In oil–air lubrication systems, large numbers of air microbubbles are often included in the oil phase. However, the principles of microbubble formation in oil–air annular flow and their influencing factors remain uncertain, and previous conclusions regarding the effects of microbubbles on the viscosity properties of the lubricant oil are inconsistent. Thus, there is an urgent need for experimental verification. In this paper, a transient force balance model is established and used to ascertain the formation of air microbubbles in oil (AB-oil) for an oil–air annular flow. The stability of these microbubbles is analyzed using the Rayleigh–Plesset equation. Theoretical analysis shows that the microbubble radius is the key factor affecting the force balance and stability of microbubbles in oil. Experiments are conducted based on this theoretical analysis, and the void fraction of AB-oil is determined through image analysis to verify the principles and influencing factors of AB-oil formation in oil–air lubrication systems. The viscosity properties of AB-oil are then tested using a rheometer. The experimental results indicate that the formation of AB-oil is affected by oil viscosity, pipe range, oil feeding rate, and air pressure. AB-oil exhibit different viscosity properties at different shear rates and void fractions. Finally, the relationship between the void fraction and viscosity at different shear rates is determined from the experimental data. The outcomes of this research provide insights into the characteristics of oil–air lubrication systems for high-speed machine tool spindles. [ABSTRACT FROM AUTHOR]

Gas–liquid two-phase flow is very common in industrial pipelines. Flow regime identification is the first step to design, analyze, and operate the gas–liquid system successfully. The purpose of this study is to develop a methodology for identification of a two-phase flow regime using post signal processing techniques, namely Fast Fourier Transform (FFT) and Probabilistic Density Function (PDF). Three different flow regimes were simulated in a 6 m horizontal pipe with a 0.050 m inner diameter. A Level-Set (LS) method coupled with Volume of Fluid (VOF) method is used to model the air–water interface. After validation of the numerical method, dynamic pressure readings were collected with the intent to identify the associated flow regimes by post-processing of these signals. It was concluded that dynamic pressure signals of different flow regimes show different characteristics (like dominant frequency, FFT amplitude, PDF location and PDF magnitude) in the time and frequency domains. These characteristics can be potentially used as differentiating factors to distinguish different flow regimes. This research is limited to stratified, slug, and annular flow in the horizontal pipe. This paper uses a new approach to identify the flow regime in a horizontal pipe by Fast Fourier Transform and Probability Density Function of dynamic pressure readings obtained by using numerical simulation. [ABSTRACT FROM AUTHOR]

One of the most severe problems in power plants, petroleum and petrochemical industries is the accurate determination of phase fractions in two-phase flows. In this paper, we carried out experimental investigations to validate the simulations for water–air, two-phase flow in an annular pattern. To this end, we performed finite element simulations with COMSOL Multiphysics, conducted experimental investigations in concave electrode shape and, finally, compared both results. Our experimental set-up was constructed for water–air, two-phase flow in a vertical tube. Afterwards, the simulated models in the water–air condition were validated against the measurements. Our results show a relatively low relative error between the simulation and experiment indicating the validation of our simulations. Finally, we designed an Artificial Neural Network (ANN) model in order to predict the void fractions in any two-phase flow consisting of petroleum products as the liquid phase in pipelines. In this regard, we simulated a range of various liquid–gas, two-phase flows including crude oil, oil, diesel fuel, gasoline and water using the validated simulation. We developed our ANN model by a multi-layer perceptron (MLP) neural network in MATLAB 9.12.0.188 software. The input parameters of the MLP model were set to the capacitance of the sensor and the liquid phase material, whereas the output parameter was set to the void fraction. The void fraction was predicted with an error of less than 2% for different liquids via our proposed methodology. Using the presented novel metering system, the void fraction of any annular two-phase flow with different liquids can be precisely measured. [ABSTRACT FROM AUTHOR]

Copyright of Atomic Energy Science & Technology is the property of Editorial Board of Atomic Energy Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Entrainment of liquid from the film surface by high-velocity gas stream strongly affects mass, momentum and heat transfer in annular flow. The construction of basic assumptions for simplified physical models of the flow, as well as validation of numerical models, requires detailed experimental investigation of droplet entrainment process and the preceding stages of film surface evolution. The present paper analyzes the achievements and perspectives of application of various experimental approaches to qualitative and quantitative characterization of droplet entrainment. Optical visualization in at least two planes simultaneously may provide enough information on transitional liquid structures and detaching droplets, given that the side-view image is not obscured by the wall film. A planar LIF technique is not suitable for this purpose, since real objects are hidden by curved agitated interface and replaced by optical artifacts. To characterize the waves evolving into the transitional liquid structures, film thickness measurements in the plane of the wall are necessary. Such measurements can be achieved by intensity-based optical techniques, such as Brightness-Based LIF, near-infrared or X-ray attenuation techniques, combined with the side-view observations. [ABSTRACT FROM AUTHOR]

Melt-blowing technology is an important method for directly preparing micro-nanofiber materials by drawing polymer melts with high temperature and high velocity air flow. During the drawing process, the melt-blowing fiber not only undergoes a phase change, but also has an extremely complex coupling effect with the drawing airflow. Therefore, in the numerical calculation of the flow field, the existence of melt-blowing fibers is often ignored. In this paper, based on the volume of fluid method, a numerical study of the flexible fiber/air-coupling flow field of an annular melt-blowing die is carried out with the aid of computational fluid dynamics software. The results show that the pressure distribution in the different central symmetry planes of the ring die at the same time was basically the same. However, the velocity distribution may have been different; the velocity on the spinning line varied with time; the pressure changes on the spinning line were small; and velocity fluctuations around the spinning line could cause whiplash of the fibers. [ABSTRACT FROM AUTHOR]

The vibration excited by gas-liquid multiphase flow endangers the structural instability and fatigue life of subsea jumpers due to the cyclic behavior. In this paper, the multiphase flow-induced vibration (MFIV) of an M-shaped jumper is numerically investigated using a two-way fluid-structure interaction (FSI) approach. The effect of gas-liquid ratios (β) ranging from 1:1 to 1:5 is examined with a fixed flow velocity of 3 m/s, and the influence of mixture velocity (vm) in the range 2–6 m/s is evaluated with a gas-liquid ratio of 1:1. The numerical results reveal the detailed flow evolution of the gas-liquid mixture along the jumper. With inflow of slugs, the pattern successively experiences the slug flow, wavy flow, imperfect annular flow, stratified flow, churn flow, wavy flow and imperfect annular flow in the pipe segments when β = 1:1 and vm = 3 m/s. This development of mixture flow is significantly altered by changing either the gas-liquid ratio or the mixture velocity. In comparison with the flow evolution in a stationary jumper, the pattern in each pipe segment is not been substantially changed due to the limited response amplitude of order of 10−3D (D is the outer diameter of the jumper). Due to the complex flow evolution, the pressure acting on the six bends of the jumper fluctuate in multiple frequencies. Nevertheless, the dominant fluctuation frequency is approximately equal to the inflow slug frequency. Moreover, the inflow slug frequency also dominates the in-plane response of the jumper. Both the in-plane and out-of-plane responses of the jumper exhibit spatial-temporal variation characteristics. The most vigorous oscillation occurs at the midspan of the jumper. As β is reduced, the out-of-plane response of the jumper midspan is suppressed while the in-plane response is enhanced. In contrast, both the in-plane and out-of-plane oscillations of the jumper midspan are amplified with the increase of vm. [ABSTRACT FROM AUTHOR]

Most of the current studies focus on the moving heat source model of straight wheel. However, these cannot be applied to calculate the cup wheel grinding temperature field, especially for the grinding processes performed with an adaptive end-effector. Based on the moving heat method and the principle of heat source superposition, the analytical thermal model of annular moving heat source for large surface workpiece is deduced. According to the parameters of the grinding instance, the numerical model is established by the finite element method for comparison and validating in this paper. The comparison results show that the characteristics of temperature distribution predicted by the analytical model and the numerical model agree very well. Two evident peak temperatures in grinding zone appear at both edges at the back of the grinding wheel in the feed direction, and test results with different grinding parameters show the relative errors do not exceed 19%. The feasibility of the analytical model and the numerical model based on different mathematical foundations is mutually validated. In the view of the non-uniform features of temperature distribution, especially the location of the peak temperature values, there are some reasonable explanations and analyses in this paper. [ABSTRACT FROM AUTHOR]

This paper aims to summarize publications related to new generation of tube geommetry, thermal performance, and flow characteristics in different cross-sectional manners, and the effect of crucial parameters on thermal–hydraulic performance. An alternating cross-sectional tube has an enhanced vorticity without installing vortex generator devices. Multi-longitudinal vortices are induced along the length of the tube: this makes a significant enhancement in the thermal performance of the tube. Many published papers have focused on the heat transfer and flow characteristics of the alternating cross-section tubes in various configurations in the past two decades.Although the cross-sections had different shapes, the flow behaviors and vortex generation were similar. The geometric parameters, like aspect ratio, pitch length, transition length, alternating angle, phase-shifting, and the total length, influenced the thermal–hydraulic performance of the alternating cross-section tube. The flow characteristics in an annular region differed between the alternating cross-section tube as internal and external tubes. Moreover, some researchers proposed the Nu and f correlations for the practical design of heat exchangers. Finally, future research works and improvement guidelines for alternating cross-section tubes are revealed. [ABSTRACT FROM AUTHOR]

In the design process for a two-pipe vehicles transportation system, some simple mathematical models are required to quickly calculate the main characteristics of the system. For this purpose, an easy-to-handle mathematical model for the concentric annular gap flow is proposed, and the velocity expression for the concentric annular gap flow is solved using cylindrical coordinates. According to the force characteristics of the two-pipe vehicles, a mathematical model of the two-pipe vehicle motion is established, and the motion and force balance equations of the two-pipe vehicles are deduced. The experimental results are in good agreement with the model results. The factors affecting the two-pipe vehicles movement speed are analyzed, and the standard regression coefficient method in multiple regression analysis is used to determine the influence degree of each factor on the movement speed of the two-pipe vehicles. The research presented in this paper not only enriches the annular gap flow theory, but also provides a theoretical reference for the development of the two-pipe vehicles transportation technology and provides technical support for the realization of relevant industrial applications. [ABSTRACT FROM AUTHOR]

This paper proposes and researches a novel cylinder-type FOWT using a neutrally buoyant double-layer torus structure with annular flow; its oscillatory motion in severe sea conditions is controlled by a spinning top device designed as a neutrally buoyant double-layer torus structure with annular flow water in a torus structure with a small internal radius, and welded to the periphery of the cylinder-type FOWT underwater buoyancy-providing part. The rotational axis retention effect and the gyroscopic effect are considered appropriate approaches to suppress the oscillating motion of FOWT. To obtain a better hydrodynamic response, the scale of the torus structure, such as its radius, the radius of the internal annular flow water, and the angular velocity of the annular flow water are taken as the design parameters, and a large number of comparative calculations based on the fluid–solid coupling theory of potential flow are carried out to determine the appropriate design parameters. Eventually, on the basis of the obtained suitable design parameters, the proposed conceptual design approach is demonstrated to be feasible in view of the energy consumption. [ABSTRACT FROM AUTHOR]

As an excellent reducing agent, lime has an important role in the steel production process. Annular Shaft Kiln (ASK) has been widely used in the lime production industry for its low cost, low footprint, high chemical activity, easy construction, and easy maintenance. Due to the high temperature generated inside ASK during operation, it is hard to observe the limestone decomposition process and the field distribution in the lime kiln. The simulation analysis of temperature field, velocity field and decomposition field in the limestone calcination process by CFD provides practical guidance for future lime product quality control, ASK design and operation parameters' control. This study is based on an ASK that was put into production. Based on the finite volume method, this paper combines the porous medium model and the shrinking core model to establish a set of mathematical models that can describe the temperature and flow field distribution inside the ASK, as well as the limestone decomposition process and the heat and mass transfer process inside the ASK. According to the feedback from the production site, the mathematical model is in good agreement with the production results. [ABSTRACT FROM AUTHOR]

Oil–water annular flow is an efficient method of heavy oil transportation for energy-saving. To deeply study the influencing factors of the energy savings of oil–water annular flow, this paper compares the interface fluctuation and energy-saving situation of oil–water annular flow under different pipe structures (such as straight pipe, sudden-contraction pipe, and elbow pipe), flow parameters, and fluid properties. In the straight pipe, the flow parameters can impact the oil–water annular flow pattern and the energy savings, and the interface fluctuation is consistent with the energy savings. The stable oil–water core annular flow has slight interface fluctuation and significant energy savings. At the same time, the influences of pipe structure and fluid properties on energy saving are also analyzed. In the sudden-contraction pipe, the oil–water interface fluctuates, largely due to the sharp changes in flow cross-section, which leads to reduced energy savings. In the elbow, the oil–water interface fluctuates greatly due to the influence of centrifugal force caused by flow direction variation, and also leads to a decline in energy savings. The effects of oil property or annulus liquid property on the interface fluctuates, and the energy savings are analyzed; reducing surface tension is an effective measure to provide an energy-saving effect. These results can provide a reference for the design of heavy-oil-transportation pipelines, the analysis of interface fluctuation, and the energy-saving evaluation of oil–water annular flow. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Irrigation & Drainage is the property of Journal of Irrigation & Drainage Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

With the excellent heat and mass transfer performance, the annular flow has been widely employed in industries. The study on the flow characteristics distribution of annular flow is the basis for revealing the flow mechanism and improving the performance. In this paper, based on the non-invasive planar laser-induced fluorescence technology, the circumferential characteristics of liquid film in horizontal annular flow and wavy flow are investigated. The circumferential film thickness and entrainment concentration are measured by the image processing. The spatial–temporal flow structure is reconstructed, and the cross-correlation analysis is conducted. The results show that the liquid entrainment and deposition phenomena contribute to the liquid film formation near the top of the pipe. In addition, a model which predicts the circumferential film thickness according to Froude number and circumferential angle is established. [ABSTRACT FROM AUTHOR]

Rotating machinery has significant applications in the fields of micro and nano meters, such as nano-turbines, nano-motors, and biomolecular motors, etc. This paper takes rotating nano-annular plates as the research object to analyze their free vibration behaviors. Firstly, based on Kirchhoff plate theory, Mindlin plate theory, and Reddy plate theory, combined with nonlocal constitutive relations, the differential motion equations of rotating functionally graded nano-annular plates in a thermal environment are derived. Subsequently, the numerical method is used to discretize and solve the motion equations. The effects of nonlocal parameter, temperature change, inner and outer radius ratio, and rotational velocity on the vibration frequencies of the nano-annular plates are analyzed through numerical examples. Finally, the relationship between the fundamental frequencies and the thickness-to-radius ratio of the nano-annular plates of clamped inner and outer rings is discussed, and the differences in the calculation results among the three plate theories are compared. [ABSTRACT FROM AUTHOR]

Two-phase (gas–liquid) flow in vertical pipes has been one of the interests of industrial applications such as power plants, nuclear reactors, boilers, gas well exploration and so on. One of the problems usually encountered in the gas well exploration industries is liquid loading: a condition where the gas velocity is not high enough to carry all the liquid generated in the gas wells. During normal operation, flow in the gas wells shows characteristics of annular flow regime. However, as the gas wells mature, the gas velocities reduce (below a critical value) and gradually lead to the onset of liquid loading (film reversal). At this point, flow in the gas well presents features of churn flow. Thus, during the film reversal point, the liquid film tends to increase in thickness and part of it starts to flow downwards. This paper first summarizes the available mechanistic and numerical models related to liquid loading and then reviews the application of CFD techniques to liquid loading modeling in vertical pipes. Most of the methodologies discussed here focus on annular and churn flow due to the limited information on the application of CFD techniques to liquid loading modeling and the onset of film reversal occurs during the transition from annular flow to churn flow which can lead to liquid loading as observed experimentally by many researchers. It was concluded from the available literature related to liquid loading that a detailed understanding of the fluid flow behavior during liquid loading is not yet fully available and prediction methods of this phenomenon are still rather incipient. Directions for good CFD modeling of these important phenomena are presented in the present paper. [ABSTRACT FROM AUTHOR]

The annular coaxial nozzle has good convergence and is widely used in laser melting deposition (LMD). In this paper, a new-type annular coaxial nozzle is developed, which can transform four-channel powder flow into annular distribution through the internal channel to obtain a more uniform distribution of powder in the circumferential direction. A three-dimensional computational fluid dynamics (CFD) numerical model is established. The dynamic behavior of Fe-based powder is described by discrete phase model (DPM). The influence of gas on powder particles is described by two-way turbulence coupling model. The convergence and transport characteristics of the nozzle are revealed. The accuracy of CFD model is verified by powder feeding experiment, and the deposition performance of powder nozzle is verified by single-track deposition experiment. The results show that the nozzle can provide stable powder feeding and excellent convergence characteristics. The powder flow is converged in a "Y" shape on the longitudinal section. The higher the powder concentration at the focal plane of the nozzle, the smaller the aspect ratio of single-track coating. The powder utilization rate of the nozzle can reach 76.97%. [ABSTRACT FROM AUTHOR]