Search

This paper investigates a Vienna rectifier as a charger for series-connected battery packs. Focusing on carrier-based pulsewidth modulation (CBPWM), the ripple current flowing through the neutral point (NP) results in the voltage oscillation if the loads are resistive. To reduce the ripple of average NP current with mitigated distortion under balanced and unbalanced dc-link voltages conditions, a novel CBPWM with segmented component injection scheme (SCIS) is proposed in this paper. After dc component injection, continuous intervals for optimized component injection and clamping intervals for compensation component injection are identified. Optimized components are calculated originally based on unbalanced factor to make the average NP current zero-size in one switching period. Moreover, unique compensation components generate suitable NP current to shape the sinusoidal input currents according to the circuit analysis. In consequence, the SCIS not only keeps the input current with low-harmonic distortion, but also minimizes the oscillation of dc-link voltage under balanced and unbalanced conditions. In addition, the value of the NP current during the clamping intervals is analyzed under various operating conditions. The effectiveness and the performance of the proposed SCIS are verified by simulation and experiments. [ABSTRACT FROM AUTHOR]

This paper identifies extra junction capacitances and switching commutation loops introduced by line-frequency devices (i.e., non-active every other half line cycle) in three-level ac/dc converters and investigates the corresponding effects. Junction capacitances and power loops are well known as the key factors that impact converter switching loss and device stress, thus influence device selection, power stage layout, and thermal design. By examining switching transients of the commonly used T-shaped and I-shaped three-level converters, the cause and mechanism of the extra junction capacitances and power loops are presented. The impacts on switching loss, device voltage stress, and ac-side voltage/current distortion are respectively reported and analyzed. A loss calculation scheme for the three-level converter to include that extra loss is proposed. A power layout scheme to mitigate the device voltage stress is provided. Compensation and modeling of the voltage and current distortion are also proposed. Experimental results conducted on several types of three-level converter prototypes including a gallium nitride based 115 $V_{{\text{ac}}}{\text{/650}}$ Vdc/1.5-kW/450-kHz Vienna-type rectifier and a SiC mosfet based 1-kV/10-kW/280-kHz three-level active neutral-point-clamped inverter confirm the presented effects and verify the associated analysis and solutions. [ABSTRACT FROM AUTHOR]

Compared with continuous pulsewidth modulation (PWM), discontinuous PWM (DPWM) is a preferred solution in high-frequency Vienna-type rectifiers due to its inherent characteristics of less commutation number and higher efficiency. In this article, redundant clamping modes at the same subsector with opposite effects on the neutral point (NP) voltage are presented. Then, a modified DPWM (MDPWM) scheme is proposed to regulate the NP voltage by using redundant clamping modes. Thus, the NP voltage can be controlled in each switching period to lower the NP voltage fluctuation. The implementation of the proposed MDPWM is given with variable power factors analysis. Further, the switching loss comparison of conventional space vector PWM (SVPWM), hybrid DPWM (HDPWM), and proposed MDPWM is presented as well. A simulation model was built to verify the proposed NP voltage balance with different modulation indices and variable power factors. Finally, a 10-kW prototype is built to evaluate the proposed MDPWM scheme at conversion efficiency and current total harmonic distortion (THD). Experimental results and analysis show that comparing conventional SVPWM and HDPWM, the efficiency of MDPWM is the highest. The THD of DPWM is slightly higher than that of SVPWM, and it is only 2.5% at rated output power. [ABSTRACT FROM AUTHOR]

Vienna rectifier, which is a nongenerative-boost-type rectifier, is widely used in industrial applications, such as wind turbine systems. However, the Vienna rectifier will face the challenge of reducing common-mode voltage (CMV), maintaining the sinusoidal input currents, and balancing neutral-point (NP) voltage in practice. As these issues are mutually coupled, the conventional space vector modulation (SVM) and various types of enhanced schemes cannot solve these problems properly, especially under nonunity power factor operation. To overcome these limitations, a two-layer pulsewidth modulation scheme through vector selection is developed. In the first layer of the proposed strategy, the NP voltage oscillations are mitigated by adjusting the switching sequence and dwell time of large, medium, small, and zero vectors with reduced CMV as the same in large, medium, and zero vector modulation. In the second layer of the proposed strategy, the switching states are reselected, and the dwell times are real time adjusted to eliminate the distortions in input currents. Through the aforementioned two-layer control method, CMV reduction, input current distortion elimination, and NP voltage balancing in Vienna rectifier can be realized simultaneously. The correctness and effectiveness of the proposed SVM method are verified by the experiment. [ABSTRACT FROM AUTHOR]