Search

In order to study the impact of acoustic propagation characteristics in the northeastern South China Sea, GEBCO08 global terrain grid data and Argo data were used to numerically simulate the acoustic transmission characteristics of two stations in the northeast South China Sea affected by the Kuroshio. The impact of different marine environments on acoustic transmission characteristics was analyzed. The results show that increasing the deployment depth of a sound source within a certain range will reduce the transmission loss; deploying a sound source near the axis of the surface acoustic channel or the deep-sea acoustic channel will also greatly increase the propagation distance of sound signals; and the presence of topography such as undersea mountains will increase the transmission loss. [ABSTRACT FROM AUTHOR]

Recent publications on acoustic MEMS transducers present a new three-dimensional folded diaphragm that utilizes buried in-plane vibrating structures to increase the active area from a small chip volume. Characterization of the mechanical properties plays a key role in the development of new MEMS transducers, whereby established measurement methods are usually tailored to structures close to the sample surface. In order to access the lateral vibrations, extensive and destructive sample preparation is required. This work presents a new passive measurement technique that combines acoustic transmission measurements and lumped-element modelling. For diaphragms of different lengths, compliances between 0.08 × 10−15 and 1.04 × 10−15 m3/Pa are determined without using destructive or complex preparations. In particular, for lengths above 1000 µm, the results differ from numerical simulations by only 4% or less. [ABSTRACT FROM AUTHOR]

The acoustic properties of a single-stage centrifugal pump with low specific speed are investigated by means of compressible 3D CFD simulations (URANS) and experiments. In order to determine the pump's acoustic transmission and excitation characteristics, a four-pole approach in the frequency domain is used. The transmission parameters determined by simulation are compared to experiments in water and air as functions of the Helmholtz number. The results indicate that the acoustic transmission characteristics within the experiments are significantly influenced by the structural compliance of the volute casing in terms of a fluid–structure interaction (FSI). A modelling approach for a one-dimensional representation of the centrifugal pump's acoustic transmission characteristics in the time and frequency domains is applied to the current pump. As one model parameter, the effective speed of sound in the 1D model needs to be reduced to 607 m s − 1 to account for the FSI. The agreement of the simulation results and the experiments underlines the above statement about the influence of the FSI. In a last step, the acoustic excitation parameter, depicted as monopole and dipole amplitudes, at two different blade-passing frequencies ( f B P ≈ [ 111 ; 169 ] Hz) are determined for several operating points. Especially for dipole amplitudes, a good agreement between experiments and simulations can be seen. The monopole amplitudes are also of similar orders of magnitude, but show stronger deviations. The cause of discrepancies between the 3D CFD simulations and experiments is believed to be the neglected influence of the FSI and surface roughness as well as the inaccurate reproduction of flow separation at the volute's tongue due to the use of wall functions. A final important observation made during the numerical investigations is that the excitation mechanisms at the blade-passing frequency are probably independent of the piping system's acoustic impedance. [ABSTRACT FROM AUTHOR]

In order to study the impact of acoustic propagation characteristics in the northeastern South China Sea, GEBCO08 global terrain grid data and Argo data were used to numerically simulate the acoustic transmission characteristics of two stations in the northeast South China Sea affected by the Kuroshio. The impact of different marine environments on acoustic transmission characteristics was analyzed. The results show that increasing the deployment depth of a sound source within a certain range will reduce the transmission loss; deploying a sound source near the axis of the surface acoustic channel or the deep-sea acoustic channel will also greatly increase the propagation distance of sound signals; and the presence of topography such as undersea mountains will increase the transmission loss.

Recent publications on acoustic MEMS transducers present a new three-dimensional folded diaphragm that utilizes buried in-plane vibrating structures to increase the active area from a small chip volume. Characterization of the mechanical properties plays a key role in the development of new MEMS transducers, whereby established measurement methods are usually tailored to structures close to the sample surface. In order to access the lateral vibrations, extensive and destructive sample preparation is required. This work presents a new passive measurement technique that combines acoustic transmission measurements and lumped-element modelling. For diaphragms of different lengths, compliances between 0.08 × 10−15 and 1.04 × 10−15 m3/Pa are determined without using destructive or complex preparations. In particular, for lengths above 1000 µm, the results differ from numerical simulations by only 4% or less.

An increasingly significant area of research with several applications in numerous disciplines is that of multi-neck Helmholtz resonators. This research is set to explore the accuracy and applicability of the finite element method (FEM) for the calculation of the resonance frequency of multi-neck Helmholtz resonators. The FEM is employed for the estimation of the resonance frequency in various cases of multi-neck Helmholtz resonators: with cylindrical or spherical bodies, with unflanged or flanged necks of various dimensions and with various combinations of the above. Also, single neck resonators are examined. The FEM results are compared with the results of a recently proposed theoretical model available in the literature and with the outcome of the lumped element approximation (multi-neck) accounting for the added neck surface area. Comparisons revealed little deviation between the FEM and theoretical model (less than 1.1% error of calculation for every case). On the contrary, in comparison with the lumped element approximation (multi-neck), the error of calculation is significant (up to 40.3% for the cases examined). The FEM will prove useful in expanding our understanding of how multi-neck Helmholtz resonators perform under various conditions and configurations. The present research, which highlights the applicability of the FEM for the calculations of the resonance frequency of multi-neck Helmholtz resonators, goes a step further; this approach can be applied in special cases where it is not trivial to apply an analytical formula. The method can be used for applications of multi-neck Helmholtz resonators for various fields such as acoustic metamaterials, musical acoustics and noise mitigation. [ABSTRACT FROM AUTHOR]

One of the uses of Helmholtz resonators is as sound absorbers for room acoustic applications, especially for the low frequency range. Their efficiency is centered around their resonance frequency which mainly depends on elements of their geometry such as the resonator volume and neck dimensions. Incorporating additional necks on the body of a Helmholtz resonator (depending on whether they are open or closed) has been found to alter the resulting resonance frequency. For this study, tunable Helmholtz resonators to multiple resonance frequencies, are proposed and investigated utilizing additional necks. The resonance frequencies of various multi-neck Helmholtz resonators are first modeled with the use of the finite element method (FEM), then calculated with the use of an analytical approach and the results of the two approaches are finally compared. The results of this study show that Helmholtz resonators with multiple resonances at desired frequencies are achievable with the use of additional necks, while FEM and analytical methods can be used for the estimation of the resonance frequencies. Analytical and FEM approach results show a good agreement in cases of small number of additional necks, while the increasing differences in cases of higher neck additions, were attributed to the change in effective length of the necks as demonstrated by FEM. The proposed approach can be useful for tunable sound absorbers for room acoustics applications according to the needs of a space. Also, this approach can be applied in cases of additional tunable air resonances of acoustic instruments (e.g., string instruments). [ABSTRACT FROM AUTHOR]

ObjectivesThis study seeks to expand the bandgap frequency band, reduce the bandgap starting frequency and analyze and optimize the bandgap parameters of acoustic metamaterials. MethodsThe influence of geometrical and material parameters on the bandgap properties of acoustic metamaterials is analyzed, and a method for maximizing the bandgap width is proposed. The multi-objective optimization problem is converted into a single objective optimization problem by normalizing the bandgap frequency coefficients. Structural material conversion is achieved via the material selection optimization method, and the optimization equations of bandgap parameters are established on the basis of weight-lightening. For chiral acoustic metamaterials, the material properties (density and wave velocity) and geometric parameters (scatterer diameter, ligament thickness and coating thickness) are defined as design variables, and the comprehensive optimization of structural parameters and material selection of acoustic metamaterials based on weight-lightening are implemented. ResultsThe optimization results show that the bandgap width increases by 27.7% and the lower bound frequency decreases by 1048 Hz, thereby achieving the goal of expanding the bandgap width based on lightweight acoustic metamaterials. The acoustic transmission analysis of the finite chiral acoustic metamaterial structure is then carried out to verify the effectiveness of the proposed method. ConclusionsThe results show that the goal of lightweight acoustic metamaterials can be effectively achieved by integrating the comprehensive optimization of structural parameters and materials. As such, this study provides references for the design of new-type acoustic metamaterials.

The acoustic properties of a single-stage centrifugal pump with low specific speed are investigated by means of compressible 3D CFD simulations (URANS) and experiments. In order to determine the pump’s acoustic transmission and excitation characteristics, a four-pole approach in the frequency domain is used. The transmission parameters determined by simulation are compared to experiments in water and air as functions of the Helmholtz number. The results indicate that the acoustic transmission characteristics within the experiments are significantly influenced by the structural compliance of the volute casing in terms of a fluid–structure interaction (FSI). A modelling approach for a one-dimensional representation of the centrifugal pump’s acoustic transmission characteristics in the time and frequency domains is applied to the current pump. As one model parameter, the effective speed of sound in the 1D model needs to be reduced to 607 ms−1 to account for the FSI. The agreement of the simulation results and the experiments underlines the above statement about the influence of the FSI. In a last step, the acoustic excitation parameter, depicted as monopole and dipole amplitudes, at two different blade-passing frequencies (fBP≈[111;169] Hz) are determined for several operating points. Especially for dipole amplitudes, a good agreement between experiments and simulations can be seen. The monopole amplitudes are also of similar orders of magnitude, but show stronger deviations. The cause of discrepancies between the 3D CFD simulations and experiments is believed to be the neglected influence of the FSI and surface roughness as well as the inaccurate reproduction of flow separation at the volute’s tongue due to the use of wall functions. A final important observation made during the numerical investigations is that the excitation mechanisms at the blade-passing frequency are probably independent of the piping system’s acoustic impedance.

An increasingly significant area of research with several applications in numerous disciplines is that of multi-neck Helmholtz resonators. This research is set to explore the accuracy and applicability of the finite element method (FEM) for the calculation of the resonance frequency of multi-neck Helmholtz resonators. The FEM is employed for the estimation of the resonance frequency in various cases of multi-neck Helmholtz resonators: with cylindrical or spherical bodies, with unflanged or flanged necks of various dimensions and with various combinations of the above. Also, single neck resonators are examined. The FEM results are compared with the results of a recently proposed theoretical model available in the literature and with the outcome of the lumped element approximation (multi-neck) accounting for the added neck surface area. Comparisons revealed little deviation between the FEM and theoretical model (less than 1.1% error of calculation for every case). On the contrary, in comparison with the lumped element approximation (multi-neck), the error of calculation is significant (up to 40.3% for the cases examined). The FEM will prove useful in expanding our understanding of how multi-neck Helmholtz resonators perform under various conditions and configurations. The present research, which highlights the applicability of the FEM for the calculations of the resonance frequency of multi-neck Helmholtz resonators, goes a step further; this approach can be applied in special cases where it is not trivial to apply an analytical formula. The method can be used for applications of multi-neck Helmholtz resonators for various fields such as acoustic metamaterials, musical acoustics and noise mitigation.

The characteristics of transmitted acoustic field have important significance to the leakage detection and the acoustic metasurface technology. When the additional leak holes are present, the conventional single neck Helmholtz resonator will naturally become the one with multiple necks. Based on such a background, in this paper, the effects of leakages on the transmission properties of a Duct Helmholtz Resonator (DHR) device is investigated both analytically and numerically. A set of closed-form formulas are derived to analytically predict the transmission spectra of the DHR device with leakages. The theoretical results are compared with COMSOL predictions. The simulation results show that the number and width of leak holes have significant influences on the amplitude, phase shift of the transmitted wave, and resonance frequency of the DHR system. [ABSTRACT FROM AUTHOR]

Abstract Background The clinical applications of transcranial focused ultrasound continue to expand and include ablation as well as drug delivery applications in the brain, where treatments are typically guided by MRI. Although MRI-guided focused ultrasound systems are also preferred for many preclinical investigations, they are expensive to purchase and operate, and require the presence of a nearby imaging center. For many basic mechanistic studies, however, MRI is not required. The purpose of this study was to design, construct, characterize and evaluate a portable, custom, laser-guided focused ultrasound system for noninvasive, transcranial treatments in small rodents. Methods The system comprised an off-the-shelf focused ultrasound transducer and amplifier, with a custom cone fabricated for direct coupling of the transducer to the head region. A laser-guidance apparatus was constructed with a 3D stage for accurate positioning to 1 mm. Pressure field simulations were performed to demonstrate the effects of the coupling cone and the sealing membrane, as well as for determining the location of the focus and acoustic transmission across rat skulls over a range of sizes. Hydrophone measurements and exposures in hydrogels were used to assess the accuracy of the simulations. In vivo treatments were performed in rodents for opening the blood–brain barrier and to assess the performance and accuracy of the system. The effects of varying the acoustic pressure, microbubble dose and animal size were evaluated in terms of efficacy and safety of the treatments. Results The simulation results were validated by the hydrophone measurements and exposures in the hydrogels. The in vivo treatments demonstrated the ability of the system to open the blood–brain barrier. A higher acoustic pressure was required in larger-sized animals, as predicted by the simulations and transmission measurements. In a particular sized animal, the degree of blood–brain barrier opening, and the safety of the treatments were directly associated with the microbubble dose. Conclusion The focused ultrasound system that was developed was found to be a cost-effective alternative to MRI-guided systems as an investigational device that is capable of accurately providing noninvasive, transcranial treatments in rodents.

The characteristics of transmitted acoustic field have important significance to the leakage detection and the acoustic metasurface technology. When the additional leak holes are present, the conventional single neck Helmholtz resonator will naturally become the one with multiple necks. Based on such a background, in this paper, the effects of leakages on the transmission properties of a Duct Helmholtz Resonator (DHR) device is investigated both analytically and numerically. A set of closed-form formulas are derived to analytically predict the transmission spectra of the DHR device with leakages. The theoretical results are compared with COMSOL predictions. The simulation results show that the number and width of leak holes have significant influences on the amplitude, phase shift of the transmitted wave, and resonance frequency of the DHR system.

Trade-offs shaping behavioral variation are often influenced by the environment. We investigated the role that the environment plays in mediating trade-offs using a widespread frog with a conspicuous mating display, Pseudacris crucifer. We first demonstrated, using playback and desiccation experiments, that calling site selection involves a trade-off between sound transmission and desiccation. We then determined the influence of local environmental conditions on the intensity of the trade-off by examining range-wide behavioral and environmental data. We showed that the benefit of improved call transmission is positively influenced by vegetation density and ground cover. Behavioral data are consistent with this relationship: sites with a greater transmission benefit have increased prevalence of arboreally calling males. We also found that the prevalence of arboreal calling behavior increases with relative humidity and air temperature, suggesting an influence of these environmental variables on the desiccation cost of arboreal calling. This study provides a clear example of the role of the environment in mediating trade-off intensities and shaping critical behavioral traits. Local environment mediates the intensity of a trade-off associated with arboreal calling behavior in a treefrog. Combining observational and experimental approaches, we show that arboreal calling behavior increases the transmission of a mating call while potentially subjecting individuals to a rate of desiccation six times greater than terrestrial calling. Local environmental conditions influence both the benefit and the cost of this trade-off, subjecting different populations to varying trade-off intensities and shaping arboreal calling behavior. [ABSTRACT FROM AUTHOR]

Subject of discussion are simulations and experimental investigations on the acoustic characterization of three single stage centrifugal pumps of different specific speed. In operation, these pump-types generate pressure pulsation at blade passing frequency, primarily due to rotor-volute-interaction. In order to determine the acoustic excitation it is necessary to know about the pumps' acoustic transmission parameters. In this paper, a one-dimensional numerical model for transient time-domain simulation is presented, which takes into account the pump geometry as well as the volutes' structural behaviour by means of the local effective speed of sound. Numerical results for the transmission characteristics of the three different pumps are shown in terms of scattering matrices and evaluated against parameters calculated from measurement results. The experimental analyses are carried out using dynamic pressure sensors in both the suction and the discharge pipe. Assuming solely plane wave propagation, the complex acoustic field on each side is evaluated independently. The so called "two source" method is then used to determine the transmission parameters of the pumps in standstill for a range of frequencies experimentally. Subsequently, the acoustic excitation at varying rotational speed is evaluated by means of measurements at the pumps in operation and presented as monopole and dipole source types for cavitation-free conditions. [ABSTRACT FROM AUTHOR]

Inspired by the mechanisms of bone conduction transmission, we present a novel sensor and actuation system that enables a smartwatch to securely communicate with a peripheral touch device, such as a smartphone. Our system regards hand structures as a mechanical waveguide that transmits particular signals through mechanical waves. As a signal, we used high-frequency vibrations (18.0–20.0 kHz) so that users cannot sense the signals either tactually or audibly. To this end, we adopted a commercial surface transducer, which is originally developed as a bone-conduction actuator, for mechanical signal generation. At the receiver side, a piezoelement was adopted for picking up the transferred mechanical signals. Experimental results have shown that the proposed system can successfully transfer data using mechanical waves. We also validate dual-frequency actuations under which high-frequency signals (18.0–20.0 kHz) are generated along with low-frequency (up to 250 Hz) haptic vibrations. The proposed method has advantages in terms of security in that it does not reveal the signals outside the body, meaning that it is not possible for attackers to eavesdrop on the signals. To further illustrate the possible application spaces, we conclude with explorations of the proposed approach.

This paper investigates a diffuse acoustic field to analyze the wave propagation on infinite doubly curved laminated composite shell sandwiching a porous material which is extensively used in aerospace structures. In fact, the main goal is to study the influence of embedded porous core on Sound Transmission Loss (STL) of the structure. Accordingly, Biot's theory is employed to model the poroelastic material which considers three types of wave propagation including two compression and one shear terms. In addition, Shear Deformation Shallow Shell Theory (SDSST) is applied to derive the wave propagation through double-walled laminated composite shell. Moreover, a numerical process is prepared to investigate a random incidence STL in a diffuse acoustic field which results in presenting the Limiting angle of incidence in which no incident wave is transmitted through structure. Then, in order to show the accuracy and the reliability of the present results, some comparisons are made between the achieved results and those of analytical as well as experimental results available in literature. Besides, the importance of using porous material as a core has been presented. Finally, some effective parameters have been studied in numerical results to inspect the insulation property of the current composite structure. [ABSTRACT FROM AUTHOR]

Subject of discussion are simulations and experimental investigations on the acoustic characterization of three single stage centrifugal pumps of different specific speed. In operation, these pump-types generate pressure pulsation at blade passing frequency, primarily due to rotor-volute-interaction. In order to determine the acoustic excitation it is necessary to know about the pumps’ acoustic transmission parameters. In this paper, a one-dimensional numerical model for transient time-domain simulation is presented, which takes into account the pump geometry as well as the volutes’ structural behaviour by means of the local effective speed of sound. Numerical results for the transmission characteristics of the three different pumps are shown in terms of scattering matrices and evaluated against parameters calculated from measurement results. The experimental analyses are carried out using dynamic pressure sensors in both the suction and the discharge pipe. Assuming solely plane wave propagation, the complex acoustic field on each side is evaluated independently. The so called “two source” method is then used to determine the transmission parameters of the pumps in standstill for a range of frequencies experimentally. Subsequently, the acoustic excitation at varying rotational speed is evaluated by means of measurements at the pumps in operation and presented as monopole and dipole source types for cavitation-free conditions.

Underwater sensor networks represent an important and promising field of research due to the large diversity of underwater ubiquitous applications that can be supported by these networks, e.g., systems that deliver tsunami and oil spill warnings, or monitor submarine ecosystems. Most of these monitoring and warning systems require real-time communication in wide area networks that have a low density of nodes. The underwater communication medium involved in these networks is very harsh and imposes strong restrictions to the communication process. In this scenario, the real-time transmission of information is done mainly using acoustic signals, since the network nodes are not physically close. The features of the communication scenario and the requirements of the communication process represent major challenges for designers of both, communication protocols and monitoring and warning systems. The lack of models to represent these networks is the main stumbling block for the proliferation of underwater ubiquitous systems. This paper presents a real-time communication model for underwater acoustic sensor networks (UW-ASN) that are designed to cover wide areas with a low density of nodes, using any-to-any communication. This model is analytic, considers two solution approaches for scheduling the real-time messages, and provides a time-constraint analysis for the network performance. Using this model, the designers of protocols and underwater ubiquitous systems can quickly prototype and evaluate their solutions in an evolving way, in order to determine the best solution to the problem being addressed. The suitability of the proposal is illustrated with a case study that shows the performance of a UW-ASN under several initial conditions. This is the first analytic model for representing real-time communication in this type of network, and therefore, it opens the door for the development of underwater ubiquitous systems for several application scenarios. [ABSTRACT FROM AUTHOR]

The objective of the paper is to demonstrate the homogenization approach applied to modelling the acoustic transmission on perforated interfaces embedded in the acoustic fluid. We assume a layer, with periodically perforated obstacles, separating two half-spaces filled with the fluid. The homogenization method provides limit transmission conditions which can be prescribed at the homogenized surface representing the "limit" interface. The conditions describe relationship between jump of the acoustic pressures and the transversal acoustic velocity, on introducing the "in-layer pressure" which describes wave propagation in the tangent directions with respect to the interface.This approach may serve as a relevant tool for optimal design of devices aimed at attenuation of the acoustic waves, such as the engine exhaust mufflers or other structures fitted with sieves and grillages. We present numerical examples of wave propagation in a muffler-like structure illustrating viability of the approach when complex 3D geometries of the interface perforation are considered.

The paper deals with modeling the acoustic transmission through a perforated interface plane separating two halfspaces occupied by the acoustic medium. We considered the two-scale homogenization limit of the standard acoustic problem imposed in the layer with the perforated periodic structure embedded inside. The homogenized transmission conditions govern the interface discontinuity of the acoustic pressure associated with the two halfspaces and the magnitude of the fictitious transversal acoustic velocity. By numerical examples we illustrate this novel approach of modeling the acoustic impedance of perforated interfaces.

Underwater sensor networks are becoming an important field of research, because of their everyday increasing application scope. Examples of their application areas are environmental and pollution monitoring (mainly oil spills), oceanographic data collection, support for submarine geolocalization, ocean sampling and early tsunamis alert. The challenge of performing underwater communications is well known, provided that radio signals are useless in this medium, and a wired solution is too expensive. Therefore, the sensors in these networks transmit their information using acoustic signals that propagate well under water. This data transmission type not only brings an opportunity, but also several challenges to the implementation of these networks, e.g., in terms of energy consumption, data transmission and signal interference. In order to help advance the knowledge in the design and implementation of these networks for monitoring underwater spaces, this paper proposes a MAC protocol for acoustic communications between the nodes, based on a self-organized time division multiple access mechanism. The proposal was evaluated using simulations of a real monitoring scenario, and the obtained results are highly encouraging. [ABSTRACT FROM AUTHOR]

Underwater sensor networks represent an important and promising field of research due to the large diversity of underwater ubiquitous applications that can be supported by these networks, e.g., systems that deliver tsunami and oil spill warnings, or monitor submarine ecosystems. Most of these monitoring and warning systems require real-time communication in wide area networks that have a low density of nodes. The underwater communication medium involved in these networks is very harsh and imposes strong restrictions to the communication process. In this scenario, the real-time transmission of information is done mainly using acoustic signals, since the network nodes are not physically close. The features of the communication scenario and the requirements of the communication process represent major challenges for designers of both, communication protocols and monitoring and warning systems. The lack of models to represent these networks is the main stumbling block for the proliferation of underwater ubiquitous systems. This paper presents a real-time communication model for underwater acoustic sensor networks (UW-ASN) that are designed to cover wide areas with a low density of nodes, using any-to-any communication. This model is analytic, considers two solution approaches for scheduling the real-time messages, and provides a time-constraint analysis for the network performance. Using this model, the designers of protocols and underwater ubiquitous systems can quickly prototype and evaluate their solutions in an evolving way, in order to determine the best solution to the problem being addressed. The suitability of the proposal is illustrated with a case study that shows the performance of a UW-ASN under several initial conditions. This is the first analytic model for representing real-time communication in this type of network, and therefore, it opens the door for the development of underwater ubiquitous systems for several application scenarios.

Acoustic metastructures exhibit an unprecedented ability to arbitrarily manipulate the properties of sound waves, including amplitude and phase modulation which has attracted much attention in both the academic and industrial communities. Design of metastructures has been extensively investigated for the purpose of the independent manipulation of acoustic and elastic waves. It is up to now unclear however if the optimal dissipation approach involves locally resonant structural elements, or locally resonant acoustic cavities or a hybrid mix of both noise abatement mechanisms. To study this problem, we investigate numerically and experimentally the noise reduction performance of acoustic and mechanically locally resonant structures and how they perform when integrated into the same application scenario. Taking the noise emission of an electric motor as the excitation regime for our study, the acoustic and mechanical metamaterial structures with respective C-shape and T-shaped resonators are judiciously designed to maximize noise dissipation within two targeted frequency bands where the motor noise peaks. A hybrid structure with a mix of both resonators is also designed. The results demonstrate that all three metastructure designs improved the noise attenuation performance with an additional sound insertion loss of up to 16 dB when compared to a flat wall structure of equivalent mass. The findings in this work demonstrate that significant noise attenuation can be obtained by incorporating these acoustic and mechanical meta-atoms into a wall architecture which may have great potential for real world applications such as surrounding electric motors which tend to emit monotonic and irritating noise. • We identify pronounced noise signatures for a typical electric motor. • Metastructures are designed for damping noise within two targeted frequency bands. • The mechanical resonance, acoustic resonance and a hybrid design for noise damping. • Large-scalemetastructures are experimentally tested within an anechoic chamber. [ABSTRACT FROM AUTHOR]

Underwater sensor networks are becoming an important field of research, because of their everyday increasing application scope. Examples of their application areas are environmental and pollution monitoring (mainly oil spills), oceanographic data collection, support for submarine geolocalization, ocean sampling and early tsunamis alert. The challenge of performing underwater communications is well known, provided that radio signals are useless in this medium, and a wired solution is too expensive. Therefore, the sensors in these networks transmit their information using acoustic signals that propagate well under water. This data transmission type not only brings an opportunity, but also several challenges to the implementation of these networks, e.g., in terms of energy consumption, data transmission and signal interference. In order to help advance the knowledge in the design and implementation of these networks for monitoring underwater spaces, this paper proposes a MAC protocol for acoustic communications between the nodes, based on a self-organized time division multiple access mechanism. The proposal was evaluated using simulations of a real monitoring scenario, and the obtained results are highly encouraging.

The propagation of longitudinal acoustic waves in multilayer structures based on porous silicon and the experimental measurement of acoustic transmission for the structures in the gigahertz range are reported and studied theoretically. The considered structures exhibit band gaps in the transmission spectrum and these are localized modes inside the band gap, coming from defect layers introduced in periodic systems. The frequency at which the acoustic resonances appear can be tuned by changing the porosity and/or thickness of the defect layer. [ABSTRACT FROM AUTHOR]