Search

The vertical turbulent transfer of heat and momentum in the lower atmospheric boundary layer is accom-plished through intermittent sweep, ejection, outward interaction, and inward interaction events associated with turbulent updrafts and downdrafts. These events, collectively referred to as sweep–ejection dynamics, have been studied extensively in forested and nonforested environments and reported in the literature. However, little is known about the sweep–ejection dynamics that occur in response to turbulence regimes induced by wildland fires in forested and nonforested environments. This study attempts to fill some of that knowledge gap through analyses of turbulence data previously collected during three wildland (prescribed) fires that occurred in grassland and forested environments in Texas and New Jersey. Tower-based high-frequency (10 or 20 Hz) three-dimensional wind-velocity and temperature measurements are used to examine fre-quencies of occurrence of sweep, ejection, outward interaction, and inward interaction events and their actual contributions to the mean vertical turbulent fluxes of heat and momentum before, during, and after the passage of fire fronts. The observational results suggest that wildland fires in these environments can substantially change the sweep–ejection dynamics for turbulent heat and momentum fluxes that typically occur when no fires are present, especially the relative contributions of sweeps versus ejections in determining overall heat and momentum fluxes.

The ambient atmospheric environment affects the growth and spread of wildland fires, whereas heat and moisture released from the fires and the reduction of the surface drag in the burned areas can significantly alter local atmospheric conditions. Observational studies on fire–atmosphere interactions have used instrumented towers to collect data during prescribed fires, but a few towers in an operational-scale burn plot (usually > 10 3 m2) have made it extremely challenging to capture the myriad of factors controlling fire–atmosphere interactions, many of which exhibit strong spatial variability. Here, we present analyses of atmospheric turbulence data collected using a 4 × 4 array of fast-response sonic anemometers during a fire experiment on a 10 m × 10 m burn plot. In addition to confirming some of the previous findings on atmospheric turbulence associated with low-intensity surface fires, our results revealed substantial heterogeneity in turbulent intensity and heat and momentum fluxes just above the combustion zone. Despite the small plot (100 m2), fire-induced atmospheric turbulence exhibited strong dependence on the downwind distance from the initial line fire and the relative position specific to the fire front as the surface fire spread through the burn plot. This result highlights the necessity for coupled atmosphere–fire behavior models to have 1–2 m grid spacing to resolve heterogeneities in fire–atmosphere interactions that operate on spatiotemporal scales relevant to atmospheric turbulence. The findings here have important implications for modeling smoke dispersion, as atmospheric dispersion characteristics in the vicinity of a wildland fire are directly affected by fire-induced turbulence. [ABSTRACT FROM AUTHOR]

Mesoscale models are a class of atmospheric numerical model designed to simulate atmospheric phenomena with horizontal scales of about 2-200 km, although they are also applied to microscale phenomena, with horizontal scales less than about 2 km. Mesoscale models are capable of simulating wildland fire impacts on atmospheric flows if combustion by-products (e.g., heat, smoke) are properly represented in the model. One of the primary challenges encountered in applying a mesoscale model to studies of fire-perturbed flows is the representation of the fire sensible heat source in the model. Two primary methods have been implemented previously: turbulent sensible heat flux, either in the form of an exponentially-decaying vertical heat flux profile or surface heat flux; and soil temperature perturbation. In this study, the ARPS-CANOPY model, a version of the Advanced Regional Prediction System (ARPS) model with a canopy submodel, is utilized to simulate the turbulent atmosphere during a low-intensity operational prescribed fire in the New Jersey Pine Barrens. The study takes place in two phases: model assessment and model sensitivity. In the model assessment phase, analysis is limited to a single control simulation in which the fire sensible heat source is represented as an exponentially-decaying vertical profile of turbulent sensible heat flux. In the model sensitivity phase, a series of simulations are conducted to explore the sensitivity of model-observation agreement to (i) the method used to represent the fire sensible heat source in the model and (ii) parameters controlling the magnitude and vertical distribution of the sensible heat source. In both phases, momentum and scalar fields are compared between the model simulations and data obtained from six flux towers located within and adjacent to the burn unit. The multi-dimensional model assessment confirms that the model reproduces the background and fire-perturbed atmosphere as depicted by the tower observations, although the model underestimates the turbulent kinetic energy at the top of the canopy at several towers. The model sensitivity tests reveal that the best agreement with observations occurs when the fire sensible heat source is represented as a turbulent sensible heat flux profile, with surface heat flux magnitude corresponding to the peak 1-min mean observed heat flux averaged across the flux towers, and an e-folding extinction depth corresponding to the average canopy height in the burn unit. The study findings provide useful guidance for improving the representation of the sensible heat released from low-intensity prescribed fires in mesoscale models. [ABSTRACT FROM AUTHOR]