Search

The purpose of this study was to employ complexity theory as a theoretical framework and technology to facilitate the development of a life-long learning model for non-working time in the interdependent homes for adults with Autism Spectrum Disorders (ASD). A "Shining Star Sustainable Action Project" of the ROC Foundation for Autistic Children and Adults in Taiwan (FACT) was selected as the research target, and the staff of the FACT, the medical team of the Hualian Yuli Veteran Hospital, adults with autism and their families were interviewed, observed and analyzed to develop this model during four short-stays of the project from July 2009 to December 2010. Participant field observation and informal conversations were employed and qualitative data were analyzed by using the constant comparison method through application of QSR Nvivo 9. The results showed that dynamic interaction, mutual adaptation, self-organization and co-evolution are four key elements for developing a viable life-long learning model for non-working time in the interdependent homes for adults with ASD to adapt to the impact of an aging society, to improve the quality of medical services, and to enhance the quality of life for the medical teams, patients and their families. The present study also found that the model help medical teams to avoid burnout by learning leisure skills and relaxation techniques, ways to release stress and how to enhance life-long learning for themselves and caregivers/patients' families. (Contains 5 figures and 1 table.)

Using two kinds of targets (gallium and silicon dioxide) and the rf magnetron sputtering deposited technique, GdOx:SiO2 thin film RRAM devices were deposited on TiN/Si substrate to form a metal–insulator–metal (MIM) structure. In addition, different oxygen concentrations and rf sputtering power parameters were prepared for the GdOx:SiO2 thin films. Decrease of the defects and oxygen vacancies of the GdOx:SiO2 thin films were used and repaired by rapid thermal annealing technology. Indium tin oxide (ITO) as the top electrode on the GdOx:SiO2 thin film was prepared by the physical vapor deposition (PVD) method, and ITO/GdOx:SiO2/TiN/Si structures of the GdOx:SiO2 thin films' RRAM devices were also made. In addition, the current–voltage curves and devices' endurance properties were measured by an impedance analyzer. Finally, the crystalline style, the preferred phase, the grain size, and surface microstructure of the thin films were analyzed and observed from X-ray diffraction and field emission scanning electron microscope measurements. [ABSTRACT FROM AUTHOR]

By the conventional solid state reaction method, a small amount of lithium fluoride (LiF) was used as the sintering promoter to improve the sintering and piezoelectric characteristics of (Ba0.95Ca0.05)(Ti0.93Sn0.07)O3 (BCTS) lead-free piezoceramic sheets. Using X-ray diffraction (XRD) and a scanning electron microscope (SEM), the inferences of the crystalline and surface microstructures were obtained and analyzed. Then, the impedance analyzer and d33-meter were used to measure the dielectric and piezoelectric characteristics. In this study, the optimum sintering temperature of the BCTS sheets decreased from 1450 °C to 1390 °C due to LiF doping. For the 0.07 wt % LiF-doped BCTS sheets sintered at 1390 °C, the piezoelectric constant (d33) is 413 pC/N, the electric–mechanical coupling coefficient (kp) is 47.5%, the dielectric loss (tan δ) is 3.9%, and the dielectric constant (εr) is 8100, which are all close to or even better than that of the pure undoped BCTS ceramics. The Curie temperature also improved, from 85 °C for pure BCTS to 140 °C for BCTS–0.07 LiF sheets. Furthermore, by using the vibration system and fixing 1.5 g tip mass at the end of the sheets, as the vibration frequency is 20 Hz, the proposed piezoelectric ceramic sheets also reveal a good energy harvesting performance at the maximum output peak voltage of 4.6 V, which is large enough and can be applied in modern low-power electronic products. [ABSTRACT FROM AUTHOR]

By the conventional solid state reaction method, a small amount of lithium fluoride (LiF) was used as the sintering promoter to improve the sintering and piezoelectric characteristics of (Ba 0.95 Ca 0.05 )(Ti 0.93 Sn 0.07 )O₃ (BCTS) lead-free piezoceramic sheets. Using X-ray diffraction (XRD) and a scanning electron microscope (SEM), the inferences of the crystalline and surface microstructures were obtained and analyzed. Then, the impedance analyzer and d 33 -meter were used to measure the dielectric and piezoelectric characteristics. In this study, the optimum sintering temperature of the BCTS sheets decreased from 1450 °C to 1390 °C due to LiF doping. For the 0.07 wt % LiF-doped BCTS sheets sintered at 1390 °C, the piezoelectric constant (d 33 ) is 413 pC/N, the electric-mechanical coupling coefficient (k p ) is 47.5%, the dielectric loss (tan δ) is 3.9%, and the dielectric constant (ε r ) is 8100, which are all close to or even better than that of the pure undoped BCTS ceramics. The Curie temperature also improved, from 85 °C for pure BCTS to 140 °C for BCTS-0.07 LiF sheets. Furthermore, by using the vibration system and fixing 1.5 g tip mass at the end of the sheets, as the vibration frequency is 20 Hz, the proposed piezoelectric ceramic sheets also reveal a good energy harvesting performance at the maximum output peak voltage of 4.6 V, which is large enough and can be applied in modern low-power electronic products., Competing Interests: The authors declared that they have no conflicts of interest to this work. We declare that we do not have any commercial or associative interest that represents a conflict of interest in connection with the work submitted.