Search

The main objective of this study is to develop spark ignition engine parameters that allow complete combustion while reducing dependence on fossil fuels. To achieve this goal, optimization of compression ratio, gasoline-ethanol mixture, ignition timing, and spark plug type was used. In addition, this study used water injection that continuously injects water before the intake manifold. In this study, the Taguchi method with the L9 orthogonal array was applied. According to the experimental verification results, the best combination to reduce exhaust emission levels is to utilize gasoline-ethanol (E70), a compression ratio (CR) of 15.6:1, an ignition degree of +4°, and a platinum spark plug. Meanwhile, the presence of water injection at 1.45 ml/s helps reduce vehicle exhaust pollutants. [ABSTRACT FROM AUTHOR]

Copyright of FME Transactions is the property of University of Belgrade, Faculty of Mechanical Engineering and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The main objective of this study is to develop spark ignition engine parameters that allow complete combustion while reducing dependence on fossil fuels. To achieve this goal, optimization of compression ratio, gasoline-ethanol mixture, ignition timing, and spark plug type was used. In addition, this study used water injection that continuously injects water before the intake manifold. In this study, the Taguchi method with the L9 orthogonal array was applied. According to the experimental verification results, the best combination to reduce exhaust emission levels is to utilize gasoline-ethanol (E70), a compression ratio (CR) of 15.6:1, an ignition degree of +4°, and a platinum spark plug. Meanwhile, the presence of water injection at 1.45 ml/s helps reduce vehicle exhaust pollutants.

Ammonia is a very promising alternative fuel for internal combustion engines, but there are some disadvantages, such as difficulty in ignition and slow combustion rate when ammonia is used alone. Aiming to address the problem of ammonia combustion difficulty, measures are proposed to improve ammonia combustion by blending hydrogen. A one-dimensional turbocharged ammonia-hydrogen engine simulation model was established, and the combustion model was corrected and verified. Using the verified one-dimensional model, the effects of different ratios of hydrogen to ammonia, different rotational speeds and loads on the combustion performance are investigated. The results show that the ignition delay and combustion duration is shortened with the increase of the hydrogen blending ratio. The appropriate amount of hydrogen blending can improve the brake's thermal efficiency. With the increase in engine speed, increasing the proportion of hydrogen blending is necessary to ensure reliable ignition. In conclusion, the ammonia-hydrogen fuel engine has good combustion performance, but it is necessary to choose the appropriate hydrogen blending ratio according to the engine's operating conditions and requirements. [ABSTRACT FROM AUTHOR]

Efficient energy exploitation is a necessary issue because it helps reduce fuel consumption and environmental pollution. Finding the optimal ignition timing (IT) for diesel engines to create high power and efficiency deserves attention. This study utilizes AVL BOOST simulation software with the Vibe 2-Zone combustion model to investigate the effect of IT and combustion duration on engine characteristics such as power, torque, and brake-specific fuel consumption (BSFC) at different engine loads and speeds. Then, the prediction models of the optimal ITs versus combustion durations for maximum power and minimum BSPFC were computed. The results show that ITs strongly affect engine performance characteristics. The optimal ITs that the engine produces maximum power at different combustion durations are unaffected by engine load. In contrast, they are considerably influenced by engine load when considering the engine-generated BSFC. The correlations of optimal IT versus combustion duration are linear functions. The prediction models can be utilized to predict the optimal ignition timings of the engine since the experimental time can be reduced when applied to the actual engine.

This study presents an experimental investigation into the impact of blending bioethanol (E100) with conventional gasoline (E0), incrementally increasing biofuel levels up to E10, E50, and E70. The test was carried out in two stages: Stage I assessed the engine's performance under fixed speeds (n = 2000 rpm and n = 2500 rpm) and fixed throttle positions (15%, 20%, and 25%) to measure changes in engine torque, efficiency, and environmental metrics by varying the concentration of bioethanol in the fuel. Stage II aimed to enrich the initial findings by conducting an additional test, running the engine at a fixed speed (n = 2000 rpm) and braking torque (MB = 80 Nm) and varying the ignition timing. Results indicated slight improvements in engine brake torque and thermal efficiency (up to 1.7%) with bioethanol content increased to 70%, and a notable reduction in incomplete combustion byproducts—carbon monoxide and hydrocarbons emissions (up 15% and 43%). Nitrogen oxide emissions were reduced by up to 23%, but carbon dioxide emissions decreased by a mere 1.1%. In order to increase thermal efficiency by adding higher bioethanol blend concentrations, adjusting the ignition timing to counter the longer ignition delay is necessary; however, higher emissions of nitrogen oxides and hydrocarbons are a major drawback of such a strategy. The results of the research are important in determining the optimal concentration of bioethanol in the mixture with gasoline for the energy and environmental sustainability of a spark ignition engine. [ABSTRACT FROM AUTHOR]

Background: Wildfires are thought to become more prevalent during periods of extended dry weather. This issue is examined using two dryness metrics commonly applied in Australian fire management agencies. Aims: This paper investigated links between wildfire incidence and the Keetch–Byram Drought Index (KBDI) and McArthur's Drought Factor (DF) across the state of Victoria, Australia. Methods: Weather records and data from 41 418 wildfires that occurred across the State over a 17-year period were compiled to examine the distributions of KBDI and DF on days with fires smaller and larger than 5 ha in area and all days, using kernel density plots. Key results: Days with fires, particularly days with fires that escaped initial attack, have higher DFs and KBDIs compared with all days. These differences vary between regions and are greatest in areas with moist climates. Conclusions and implications: An appreciation of dryness conditions using tools such as KBDI and DF is useful for understanding fire potential, particularly in areas that experience higher and more regular rainfall. McArthur's Drought Factor and the Keetch–Byram Drought Index are higher than normal on days with fires in Victoria, Australia. These metrics provide a more reliable indication of fire potential in high-rainfall areas than in lower-rainfall areas. This article belongs to the Collection Fire and Climate. [ABSTRACT FROM AUTHOR]

Abstract The spark plug of an opposed‐piston two‐stroke (OP2S) gasoline engine is arranged on the side wall of the cylinder liner, far from the center of the combustion chamber; the ignition core of the mixture is offset, the flame propagation distance is increased, the combustion duration is prolonged, and the knock tendency is severe. In this paper, a quasi‐dimensional two‐zone combustion model is used in GT‐Power software to establish a thermodynamic process simulation model and a knock prediction model is included to analyze the effect and matching of the compression ratio, ignition timing, and other thermodynamic process parameters on the knock intensity and engine performance. The extended coherent flame model combustion model is coupled with the Huh–Gosman spray model in AVL‐Fire software, and the An B knock model is used to establish an in‐cylinder combustion model and analyze the flame propagation and the knock response rate of the flat and pit piston during the combustion process. With an increase of the compression ratio, the temperature and pressure of the mixture in the combustion chamber increase at the time of ignition, which leads to the knocking combustion in the cylinder. With an increase of the ignition advance angle, the in‐cylinder pressure and temperature increase rapidly, which increases the likelihood of knocking combustion. In comparison with the pit piston combustion chamber, the flame propagation speed of the flat piston combustion chamber is relatively slow, which increases the knock tendency. The results show that lowering the compression ratio and delaying the ignition can reduce the in‐cylinder knock tendency by setting a compression ratio of 10.5 and an ignition advance angle of 20°CA. When the pit piston is used to organize the squish and inverse squish before and after the inner dead center, the flame propagation process can be promoted. The knock response rate of pit piston is 24.7% lower than that of flat top piston.

HHO gas is a gas produced from electrolysis, which is the decomposition of an electrolyte using an electric current which produces Hydrogen Gas and Oxygen Gas / Hydrogen Hydrogen Oxygen. The purpose of this study was to determine the application of HHO gas by increasing ignition timing by 3º, 6º, and 9º using an aftermarket ECU on engine performance and injection motor emissions. The method used in this study is an experiment, testing using a dinotest measuring instrument and a gas analyzer. The results obtained are the highest average power value in all tests obtained on the variable use of HHO Gas without variations in ignition timing using an aftermarket ECU of 5.90 HP at 3500 Rpm engine speed, an increase of 0.13% from the conditions of HHO Gas usage and forward time. . ignition of 3º and 6º, an increase of 0.27% from HHO gas usage conditions and a forward ignition time of 9º. Then the highest average torque value from all tests was obtained on the variable using HHO Gas and variations in ignition timing using an aftermarket ECU with an advance of 3º of 14.39 Nm at 3000 rpm engine speed, an increase of 0.29% from conditions using HHO Gas without using Variation ignition timing using aftermarket ECU.

Hydrogen internal combustion engines (H2-ICEs) have advantages such as clean combustion and zero carbon emissions, and have become one of the important technical routes for decarbonization in the internal combustion engine industry. In this paper, several key factors affecting the performance and emissions of hydrogen internal combustion engines, such as ignition timing, excess air coefficient, and hydrogen injection timing, were systematically studied on a spark ignition multi-point injection (MPI) hydrogen internal combustion engine bench. The experimental results indicate that the ignition timing controls the combustion phase of hydrogen. Moderate early ignition can improve the brake thermal efficiency (BTE) while having little impact on the NOX emissions. Excess air coefficient(λ) can significantly affect the performance and emissions of H2-ICE. Along with the increase of the λ, the NOX emissions first increases and then continues to decline. When the λ reaching 2.1 or above, near zero emissions of NOX can be achieved. The advance of hydrogen injection timing will slightly increase the peak of cylinder pressure and instantaneous heat release rate. However, overall, the impact of hydrogen injection timing on BTE and NOX emissions is not significant on MPI H2-ICE.

The effect of various ignition timing on spark ignition (SI) engines with bioethanol-isooctane mixtures has been widely studied. In the present studies, we used three different ignition angle positions, namely 9°, 12°, and 15° BTDC to increase the combustion pressure in the combustion chamber. In addition to macroscopic observations through engine performance, observations are also carried out from a molecular perspective, i.e.; atomic, bond, and bond angle properties of bioethanol-isooctane fuel. The result shows that more atoms of the isooctane carbon chain are non-rotatable (23 atomic bonds) than the 8 bonds of the bioethanol carbon chain. Furthermore, isooctane also has a wider bond angle (around 121.1745°) than the bond angle of ethanol (around 110.0476°). The unique properties of the atoms in the carbon chains of these two fuels have a direct impact on engine performance. The results show that the viscosity of bioethanol is lower when compared to isooctane, which indicates that the bioethanol molecules are more reactive and flammable. The result also found that at an ignition angle of 12° the BE50 engine has the best performance. Moreover, the test results also show that bioethanol produces clean combustion as evidenced by the lowest CO and HC gas emissions.

In this analytical investigation, preheated palm oil was used in the direct injection diesel engine with various optimization methods. The main purpose of the optimization was to get better results than the conventional engine. Raw palm oil was heated using the heat exchange process to reduce the density and viscosity. The relationship between the output process and factors response was evaluated in the design of experiment methods. The Taguchi method is an important method for optimization of the output response performance and emission characteristics of a diesel engine. Two important factors—output and input—were calculated. The input factors considered were preheated palm biodiesel blend, torque, injection pressure, compression ratio, and injection timing. The output factors calculated were smoke opacity, carbon monoxide emission, and brake-specific fuel consumption by using the signal-to-noise (S/N) ratio and analysis of variance. Carbon monoxide was most impacted by torque conditions through injection timing and injecting pressure, and opacity of smoke emission. Among them, injection timing had a higher impact. Different biodiesel blends were prepared: B10 (90% diesel + 10% oil), B20 (80% diesel + 20% oil), B30 (70% diesel + 30% oil) and B40 (60% diesel + 40% oil). Silver nanoparticles (50 ppm) were constantly mixed with the various biodiesel blends. The smoke opacity emission for the biodiesel blend B30 + 50 ppm silver nanoparticle showed the lowest S/N ratio and achieved better optimum results compared with the other blends. The blend B30 + 50 ppm silver nanoparticle showed the lowest S/N ratio value of 9.7 compared with the other blends. The smoke opacity, carbon monoxide emission, and brake-specific fuel consumption of all the response optimal factors were found to be 46.77 ppm, 0.32%, and 0.288 kg/kW·h, respectively. [ABSTRACT FROM AUTHOR]

The spark plug of an opposed‐piston two‐stroke (OP2S) gasoline engine is arranged on the side wall of the cylinder liner, far from the center of the combustion chamber; the ignition core of the mixture is offset, the flame propagation distance is increased, the combustion duration is prolonged, and the knock tendency is severe. In this paper, a quasi‐dimensional two‐zone combustion model is used in GT‐Power software to establish a thermodynamic process simulation model and a knock prediction model is included to analyze the effect and matching of the compression ratio, ignition timing, and other thermodynamic process parameters on the knock intensity and engine performance. The extended coherent flame model combustion model is coupled with the Huh–Gosman spray model in AVL‐Fire software, and the An B knock model is used to establish an in‐cylinder combustion model and analyze the flame propagation and the knock response rate of the flat and pit piston during the combustion process. With an increase of the compression ratio, the temperature and pressure of the mixture in the combustion chamber increase at the time of ignition, which leads to the knocking combustion in the cylinder. With an increase of the ignition advance angle, the in‐cylinder pressure and temperature increase rapidly, which increases the likelihood of knocking combustion. In comparison with the pit piston combustion chamber, the flame propagation speed of the flat piston combustion chamber is relatively slow, which increases the knock tendency. The results show that lowering the compression ratio and delaying the ignition can reduce the in‐cylinder knock tendency by setting a compression ratio of 10.5 and an ignition advance angle of 20°CA. When the pit piston is used to organize the squish and inverse squish before and after the inner dead center, the flame propagation process can be promoted. The knock response rate of pit piston is 24.7% lower than that of flat top piston. [ABSTRACT FROM AUTHOR]

In the present study, the countermeasures are proposed to minimize the problem on torque and power output performance and exhaust gas emissions of natural gas engine with use of lower calorific gas. An experiment was conducted to identify thermal efficiency and harmful exhaust gas emission characteristics under partial load conditions in order to improve efficient fuel use in engines affected by the introduction of low calorific gases. A countermeasure for coping with emission gas regulations and preventing thermal efficiency deterioration under rated power operating conditions was then presented. An 11 L six-cylinder turbo-charged engine for city buses compliant with the EURO 6 regulation was used in the experiment, and the results obtained using the reference natural gas fuel were compared with those obtained using simulated low calorific gases. Pure methane (CH 4) was also used to investigate the effects of gas composition changes on thermal efficiency and exhaust gas emissions.When N2is added or pure CH 4 is used under partial load operating conditions, the combustion rate decreases; consequently, the optimum ignition timing is additionally advanced relative to that obtained when the reference natural gas fuel is used. If the N2mixing ratio is increased to a minimum of 4.7% under rated power operating conditions, combustion becomes unstable. Stable operation can be secured by increasing the set base fuel amount, 2.35% and 9.41% for pure CH 4 and 8% N2, respectively; however, torque decreases in proportion to the combustion speed of the gas fuel. The strategy of boost pressure control for the torque compensation can minimize the decrease in thermal efficiency.

Natural gas (NG) has many advantages of clean fuels and can replace gasoline in spark ignition (SI) engines. However, it comes with disadvantages such as low energy density. Hydrogen blended NG can improve the fuel characteristics. Ignition timing also plays an important role in engine performance, especially at lean limits. Experiments were conducted for performance and emissions with hydrogen-compressed natural gas (HCNG) blends in a spark ignition (SI) engine with fixed ignition timing. HCNG blends with 0–15% hydrogen were tested with maximum brake torque (MBT) spark timing 30° before top dead center (BTDC) ignition. Significant reduction of carbon monoxide (CO), carbon dioxide (CO2) and hydrocarbons (HC) along with improved break thermal efficiency was observed with higher hydrogen fraction. There was no significant benefit in indicated thermal efficiency or NOx reduction by using MBT ignition. Hence, the expensive retrofitting of using variable spark timing apparatus can be avoided for on-road vehicles.

An innovative analytical approach combining game theory and particle swarm algorithms is used for the performance optimisation problem of hydrogen engines.An innovative analysis method combining game theory and particle swarm optimization algorithm was adopted to optimize the performance of hydrogen engines. Firstly, the power performance, fuel economy and emission of hydrogen internal combustion engines are studied in detail, and a three-way game model is constructed with the three as the main players, with strategic attribution for ignition timing, hydrogen injection timing and compression ratio.The simulation process of the model is then transformed into numerical optimisation by integrating the game utility function. Finally, the particle swarm algorithm is used to determine the initial set of strategies to obtain the Nash equilibrium solution.The results of the study showed that the optimized hydrogen internal combustion engine improved its power performance by 3.6%; economic efficiency increased by 5.7%; and emissions were reduced by 2% compared to the original engine. • Transforming the optimisation problem of the H2-ICE into a game theoretic problem. • A multi-objective optimization strategy based on game theory is proposed. • Determine the initial set of strategies and find the Nash equilibrium solution using particle swarm algorithm. • The operating parameters of the H2-ICE at variable compression ratios were optimally designed. [ABSTRACT FROM AUTHOR]

The application of hydrogen fuel in ORP engines makes the engine power density much higher than that of a reciprocating engine. This paper investigated the impacts of combustion characteristics, energy loss, and NOx emissions of a hydrogen-fuelled ORP engine by ignition timing over various equivalence ratios using a simulation approach based on FLUENT code without considering experiments. The simulations were conducted under the equivalence ratio of 0.5~0.9 and ignition timing of −20.8~8.3° CA before top dead centre (TDC). The engine was operated under 1000 RPM and wide-open throttle condition which was around the maximum engine torque. The results indicated that significant early ignition of the ORP engine restrained the flame development in combustion chambers due to the special relative positions of ignition systems to combustion chambers. In-cylinder pressure evolutions were insensitive to early ignition. The start of combustion was the earliest over the ignition timing of −17.3° CA for individual equivalence ratios; the correlations of the combustion durations and equivalence ratios were dependent on the ignition timing. Combustion durations were less sensitive to equivalence ratios in the ignition timing range of −14.2~−11.1° CA before TDC. The minimum and maximum heat release rates were 15 J·(°CA)−1 and 22 J·(°CA)−1 over the equivalence ratios of 0.5 and 0.9, respectively. Indicated thermal efficiency was higher than 41% for early ignition scenarios, and it was significantly affected by late ignition. Energy loss by cylinder walls and exhaust was in the range of 10~16% and 42~58% of the total fuel energy, respectively. The impacts of equivalence ratios on NOx emission factors were affected by ignition timing. [ABSTRACT FROM AUTHOR]

For electric reliability and to save energy, the distributed power generation combining cooling and heating supply called a CCHP system for architectures has many potential advantages and is widely adopted to provide electric power and to satisfy local heating and cooling loads by waste heat recovery with low carbon intensity. However, the current CCHP system usually has a fixed ratio of the power and heat due to the features of its power unit, which leads to difficulties in the load management. In this paper, based on the operation of an internal combustion engine fueled with natural gas, a novel method is proposed and studied to achieve a controllable rate of heat/power to meet different load requirements of the electricity and heat (cooling or heating loads). By varying the ignition timing of the spark ignition engine, the combustion process within the cylinder can be adjusted to occur at different crank angles so that the engine crank shaft output power (related to the generated electricity) and the heat from the exhaust gas are changed accordingly. To study the effects of ignition timing on engine power and exhaust heat energy, a two-zone model was established with a predictive combustion model. The changes in the combustion process, output power, exhaust gas temperature, and heat energy were mostly our concern. The results show that the heat/electricity ratio can be adjusted from normally 1.0 to 1.6, and they can be controlled independently under partial load operating conditions. To solve the potential thermal failure of the turbine, the extraordinarily high exhaust temperature will be adjusted by compressed air. [ABSTRACT FROM AUTHOR]

Abstract Biodiesels produced from various feedstocks have been considered as alternative fuels used in internal combustion engines without major modifications. This research focuses on producing biodiesel from waste cooking oil (WCOSD) by the catalytic cracking method using MgO as the catalyst and comparing the engine operating characteristics of the test engine when using WCOSD and traditional diesel (CD) as test fuels. As a result, the brake power of the test engine fueled WCOSD, and traditional diesel is similar. However, the engine fuel consumption in the case of using WCOSD is slight increases in some operating conditions. Also, the nitrogen oxides emissions of the test engine fueled WCOSD are higher than those of CD at all tested conditions. The trend is opposite for hydrocarbon emission as the HC emission of the engine fueled by WCOSD reduces 26.3% on average. The smoke emission of the test engine in case of using WCOSD is lower 17% on average than that of CD. However, the carbon monoxide emissions are lower at the low and medium loads and higher at the full loads. These results show that the new biodiesel has the same characteristics as those of commercial biodiesel and can be used as fuel for diesel engines.

Natural gas (NG) has many advantages of clean fuels and can replace gasoline in spark ignition (SI) engines. However, it comes with disadvantages such as low energy density. Hydrogen blended NG can improve the fuel characteristics. Ignition timing also plays an important role in engine performance, especially at lean limits. Experiments were conducted for performance and emissions with hydrogen-compressed natural gas (HCNG) blends in a spark ignition (SI) engine with fixed ignition timing. HCNG blends with 0–15% hydrogen were tested with maximum brake torque (MBT) spark timing 30° before top dead center (BTDC) ignition. Significant reduction of carbon monoxide (CO), carbon dioxide (CO2) and hydrocarbons (HC) along with improved break thermal efficiency was observed with higher hydrogen fraction. There was no significant benefit in indicated thermal efficiency or NOx reduction by using MBT ignition. Hence, the expensive retrofitting of using variable spark timing apparatus can be avoided for on-road vehicles. [ABSTRACT FROM AUTHOR]

For electric reliability and to save energy, the distributed power generation combining cooling and heating supply called a CCHP system for architectures has many potential advantages and is widely adopted to provide electric power and to satisfy local heating and cooling loads by waste heat recovery with low carbon intensity. However, the current CCHP system usually has a fixed ratio of the power and heat due to the features of its power unit, which leads to difficulties in the load management. In this paper, based on the operation of an internal combustion engine fueled with natural gas, a novel method is proposed and studied to achieve a controllable rate of heat/power to meet different load requirements of the electricity and heat (cooling or heating loads). By varying the ignition timing of the spark ignition engine, the combustion process within the cylinder can be adjusted to occur at different crank angles so that the engine crank shaft output power (related to the generated electricity) and the heat from the exhaust gas are changed accordingly. To study the effects of ignition timing on engine power and exhaust heat energy, a two-zone model was established with a predictive combustion model. The changes in the combustion process, output power, exhaust gas temperature, and heat energy were mostly our concern. The results show that the heat/electricity ratio can be adjusted from normally 1.0 to 1.6, and they can be controlled independently under partial load operating conditions. To solve the potential thermal failure of the turbine, the extraordinarily high exhaust temperature will be adjusted by compressed air.

Penelitian ini bertujuan untuk: (1) Mendeskripsikan bagaimana sensor-sensor dalam sistem EFI bekerja pada putaran idle, mesin rotasi tingkat menengah dan tinggi, dengan melihat sensor output. (2) Mengetahui pekerjaan aktuator pada Sistem EFI pada putaran idle, mesin rotasi tingkat menengah dan tinggi. Metode eksperimen digunakan untuk penelitian ini. Mesin EFI dengan tipe D EFI yang digunakan telah dianalisis. Alat pindai digunakan untuk mengamati untuk mengukur output yang dihasilkan oleh sensor dan mengukur kerja aktuator sistem EFI menggunakan alat Pindai. Dari percobaan ditemukan bahwa peningkatan putaran mesin akan menghasilkan peningkatan kerja aktuator pada Sistem EFI, yang terdiri dari Injeksi Waktu dan Pengisi Waktu Pengapian, tetapi untuk Idle Speed ​​Control Valve (ISCV) dan Intake Camshaft Timing perubahan relatif stabil.

Biodiesels produced from various feedstocks have been considered as alternative fuels used in internal combustion engines without major modifications. This research focuses on producing biodiesel from waste cooking oil (WCOSD) by the catalytic cracking method using MgO as the catalyst and comparing the engine operating characteristics of the test engine when using WCOSD and traditional diesel (CD) as test fuels. As a result, the brake power of the test engine fueled WCOSD, and traditional diesel is similar. However, the engine fuel consumption in the case of using WCOSD is slight increases in some operating conditions. Also, the nitrogen oxides emissions of the test engine fueled WCOSD are higher than those of CD at all tested conditions. The trend is opposite for hydrocarbon emission as the HC emission of the engine fueled by WCOSD reduces 26.3% on average. The smoke emission of the test engine in case of using WCOSD is lower 17% on average than that of CD. However, the carbon monoxide emissions are lower at the low and medium loads and higher at the full loads. These results show that the new biodiesel has the same characteristics as those of commercial biodiesel and can be used as fuel for diesel engines. [ABSTRACT FROM AUTHOR]

Liquefied Petroleum Gas (LPG) is an alternative fuel that has all key properties for the Spark Ignition (SI) engine. However, because of its properties, ignition timing on an LPG SI engine needs to be advanced from the reference angle to get the optimum performance. Therefore, this article presents the torque and power characteristics of a single piston LPG engine on variations of ignition timing. Evaluation of engine performance is carried out at the ignition timing of 15O, 17O, and 19O BTDC. The results showed the highest torque for LPG fuel was 10.64 Nm which was achieved at 3500 rpm with ignition timing of 19O BTDC, while the highest power for LPG fuel was 6.9 hp which was achieved at 5936 rpm with ignition timing of 19O BTDC.

The ignition timing of an SI engine is a critical parameter. The influence on residual gas, effective release energy, and emissions characteristics of ignition timing for the V-twin engine is investigated in this research. For this purpose, an experiment system was built with a dynamometer, and a model of the simulation was created. In this research, the ignition timing was varied from 10 to 45 degrees BTDC under full load operating conditions, with engine speeds ranging from 3000 to 10,000 rpm. Based on the output data, ignition timing has a major impact on the proportion of residual gas, efficient release energy, performance of the engine, and the emission characteristics. The smallest proportion of residual gas was 0.07% at 8000 rpm and ignition timing of 10 °CA. At 15 °CA of ignition timing, the highest efficient release energy was 0.817 kJ at 4000 rpm, while at 8000 rpm and 25 °CA of ignition timing, it was 0.8305 kJ. At 6000 rpm, the greatest braking torque of the engine was 21.57 Nm, while the minimal BSFC was 343.821 g/kWh. The nitrogen oxide emission and HC emission increase with the advanced ignition timing, but CO emission decreases.

The combustion characteristics of an opposed-piston two-stroke gasoline engine are investigated with experiment. The energy conversion and exergy destruction are analyzed and the organization method of the combustion process is summarized. The effects of phase difference, scavenging pressure, injection timing, ignition timing, and dual spark plug ignition scheme on the combustion process and engine performance are discussed, respectively. The heat release rate of the opposed-piston two-stroke gasoline engine is consistent with the conventional gasoline engine. With the increase of opposed-piston motion phase difference, the scavenging efficiency decreases and overmuch residual exhaust gas is not beneficial to the combustion process. Meanwhile, the faster relative velocity of the opposed-piston near the inner dead center enhances the cylinder working volume change rate, which leads to the rapid decline of in-cylinder pressure and temperature. The 15 °CA of opposed-piston motion phase difference improves the scavenging and combustion process effectively. When scavenging pressure is 0.12 MPa, the scavenging efficiency and heat release rate are improved at medium-high speed conditions. With the delay of injection timing, the flame developing period decreases gradually, and the rapid burning period decreases and then increases. The rapid burning period may reach the minimum value when the injection advance angle is 100 °CA. With the delay of ignition timing, the flame developing period increases gradually, and the rapid combustion period decreases and then increases. The rapid combustion period may reach the minimum value when the ignition advance angle is 20 °CA. Notably, the flat-top piston structure should be matched with the dual spark plug, which the ignition advance angle is 20 °CA at medium-high load conditions.

Low-temperature combustions (LTCs), such as homogeneous charge compression ignition (HCCI), could achieve high thermal efficiency and low engine emissions by combining the advantages of spark-ignited (SI) engines and compression-ignited (CI) engines. Robust control of the ignition timing, however, still remains a hurdle to practical use. A novel technology of jet-controlled compression ignition (JCCI) was proposed to solve the issue. JCCI combustion phasing was controlled by hot jet formed from pre-chamber spark-ignited combustion. Experiments were done on a modified high-speed marine engine for JCCI characteristics research. The JCCI principle was verified by operating the engine individually in the mode of JCCI and in the mode of no pre-chamber jet under low- and medium-load working conditions. Effects of pre-chamber spark timing and intake charge temperature on JCCI process were tested. It was proven that the combustion phasing of the JCCI engine was closely related to the pre-chamber spark timing. A 20 °C temperature change of intake charge only caused a 2° crank angle change of the start of combustion. Extremely low nitrogen oxides (NOx) emission was achieved by JCCI combustion while keeping high thermal efficiency. The JCCI could be a promising technology for dual-fuel marine engines.

In our previous studies, a plasma reformer system has been developed to produce syngas containing hydrogen to an electronic fuel injection motorcycle engine. In present investigation, the effect of ignition timing of the engine was considered with an improved spark plug reformer system. The spark plug reformer system included two spark plugs, three supersonic atomizers, a controlling device, and a storage tank. In the experiment, the vehicle under testing was a 1988 c.c. 4 cylinder Nissan Sentra with spark timing 16 BTDC (before top deadcenter). The emission test were tested with HAMA LPS 3000 dynamometer and MTG-5. The ignition timing are 12°, 14°, 16°, 18°, and 20° BTDC. Europe Emission standard cycle was run for the emission test. Results show that the emission of HC decreases and both NO x and CO increase with using the spark plug reforming system without changing the spark timing. The best spark timing of the engine was 14° BTDC, especially for the vehicle operated in high speed. In this operating condition, the HC and NO x decreased and CO 2 increased, however, CO also increased. [ABSTRACT FROM AUTHOR]

Ignition system is the main important part of the engine, and has absolute influence on engine performance. OpenECU for ignition timing strategy on the basis of the design and calibration work, greatly shorten the development difficulty and cycle; machine of a LNG gas ignition timing strategy has carried on the design and optimization, and combining the calculation model for the engine (air intake, compression, power, and exhaust) feedback and verification. It can save a lot of time and resources for experiment if experiments use openECU. It also can monitor the influence of the different inputs conditions on the ignition advance angle. It has realized the map of calibration, greatly shorten the development work and has certain actual application value. [ABSTRACT FROM AUTHOR]