Search

International audience; This work deals with the study of thermoset-thermoplastic blend forming an epoxy-amine/poly-etherimide phase separated to assess the dielectric and thermal performances. These materials would be good candidates to replace the passivation layer in semiconductors, particularly ones used as switches in power electronic applications. Polyimide and Parylene are usually quoted and studied. Mixtures based on polymers would be a novel candidate that can manage to be an insulator for the system. The modified and non-modified systems where characterized by transmission electron microscopy, scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, dielectric analysis and analytical simulation was carried out on dielectric measurements. These complementary techniques were used first to investigate the presence of the phase separation phenomenon and second to quantify the separated nodules size. The effect of this phase separation was examined and showed enhancement in the dielectric values compared to the pure epoxy system. It was finally simulated to show a close assumption of what is found experimentally.

Numerous techniques have been used to improve the breakdown voltage (VBR) capability of high voltage devices with the aim of getting closer to the breakdown voltage of a plane parallel junction. In this work, a peripheral protection for a 3 kV SiC bipolar diode is presented. This protection concept is based on a large and deep trench filled by an insulating material. This trench is called Deep Trench Termination (DT2) already validated in Si technology. Our results show that, on the basis of simulations with TCAD Sentaurus, it is possible to protect effectively with this type of trench. The simulation allows to optimize the characteristics of peripheral protection. To take into account the close environment of the semiconductor, the positive and negative fixed charges at the semiconductor - insulating interface have been considered. The work was focused on a 3 kV SiC bipolar diode, but the proposed solutions could be easily scale to any range of voltage.

It has been proposed recently that the lowest level of dc field, above which electrical degradation may occur, is associated with the formation of space charges in insulation. Therefore, inference of field levels above which space charge accumulates in a given material may provide fundamental information for material characterization and system design. Threshold field values were estimated through evidence of space charge accumulation derived from conduction current, space charge amplitude and electroluminescence (EL) counts vs, electrical field characteristics. Press-molded plates of polyethylene-based materials were used for this investigation. In order to be able to detect even by EL experiments the presence of the space charge accumulated at low fields, measurements were carried out during both polarization and short-circuit of specimens. It is shown that the threshold corresponding to the onset of EL upon grounding the specimen is close to the space charge accumulation threshold derived from space charge and conduction current measurements. This earlier value is considerably lower than the one previously detected from constant dc-voltage EL measurements, thus confirming that even at low fields and in the presence of voltage reversals or transients, space charges can trigger luminescence phenomena. The methodology developed in this paper enlarges the applicability of the EL technique to accommodate a wider electrical field range in view of insulation characterization.

In Insulated gate Bipolar Transistor (IGBT) modules, ceramic substrates are used as insulation between semiconductor chips and the ground potential. The substrate, semiconductor chips and connections are covered with silicone gel to prevent partial discharges (PDs) from occurring. In this work, partial discharges are investigated on laboratory samples made of metalized substrates embedded in silicone gel and various liquids. Substrates are made of aluminum nitride (AlN), alumina (Al2O3), or glass/epoxy composite. The objective is to determine the actual origin of PDs, by changing the nature of encapsulating material and substrate. The various liquids used are first characterized using a point-plane geometry. Experiments show that a rather large discrepancy on the PD behavior can be due to the ceramic substrate itself. "Good" and "bad" substrates can be identified on the basis of PD measurements. The influence of the sample preparation (degassing procedure) is also evidenced. The main conclusion obtained in this paper shows that partial discharges do not occur within the encapsulating material, contrary to most previous hypotheses, but within pores existing in sintered ceramic materials. Changing the substrate nature has a large influence on PD behavior, whereas a modification of the encapsulating material has almost no effect.

This paper presents an experimental study of streamer inception in a silicone gel. Many parameters are able to influence the inception of discharges in a gel: voltage wave shape, electrode geometry, temperature, etc. In this work, streamer inception is studied in various conditions of electrode shapes (from sharp points up to quasi-uniform field), voltage (ac, dc, impulse voltage) and temperature. Streamer inception is detected by the measurement of breakdown voltages in selected conditions. The results obtained show that streamer inception field varies when the electrode shape is changed, in a similar way as in liquids: the inception field decreases when the electrode surface increases. On the other hand, temperature and voltage wave shape have almost no influence on the inception field. Results are discussed in comparison with data already obtained in liquids in similar conditions.

Silicone gels are widely used to encapsulate power electronics modules. The objective of this paper is to study the partial discharge (PD) mechanism in a silicone gel, using electrical measurements and fast visualization. Experiments are carried out in a pointplane geometry, using either impulse voltage or ac. Under impulse voltage, the visualization shows that the first discharges recorded in a new sample are due to the initiation and propagation of "streamers", with features close to those previously reported in viscous liquids. Under ac, a stable PD regime rapidly establishes: a streamer creates a cavity with a long lifetime, and PDs occur in this cavity during the subsequent ac waves. Since slow streamers develop during long times (some ms), classical PD measurements do not provide an adequate evaluation of the actual discharge magnitude: very small PDs (1 pC) are recorded, whereas large cavities with a total charge in excess of 10 pC are actually present in the gel. When PDs are repeated permanent degradations of the gel rapidly occur, showing the limited self-healing capabilities of silicone gels.

The intent of this paper is to cross-correlate the information obtained by space charge profile analysis and electroluminescence (EL) detection in crass-linked polyethylene samples submitted to de fields, with the objective to make a link between space charge phenomena and energy release as revealed by detection of visible photons. Space charge measurements carried out at different electrical fields by the pulsed electro-acoustic method show the presence of a low-field threshold, close to 15 to 20 kV/mm, above which space charge begins to accumulate considerably in the insulation. Charges are seen to cross the insulation thickness through a packet-like behavior at higher fields, starting at about 60 to 70 kV/mm. EL measurements show the existence of two distinct thresholds, one related to the permanent excitation of EL under voltage, the other being transient EL detected upon specimen short-circuit. The former occurs at values of field corresponding to space charge packet formation, and the latter to the on-set of space charge accumulation. The two techniques give therefore consistent information on space charge phenomena and associated energy release in the optical EM spectrum.

International audience; This paper presents an investigation on the current and breakdown voltage measurements in thermoset-thermoplastic blends based on an epoxy-amine/poly-etherimide phase separated material. Thermosetthermoplastic separated blends could be a novel material for insulation applications and can be compared to epoxy/inorganic composites systems. Pure epoxy network as well as the blends with 10 wt% of PEI were studied in terms of conduction and transient currents. An ohmic behavior below the threshold field (E th) and space-chargelimited conduction (SCLC) above E th are pointed out. Contact emission phenomenon was investigated by means of Schottky model and seems to be valid for both materials. The addition of 5 and 10 wt% of PEI into the epoxy system showed an increase in the values of breakdown voltage with the increase of the PEI amount.