Search

The "weak" friction-induced vibration can help to monitor the change in friction and wear state of friction pairs and detect the failure of surface damage. However, they are typically submerged in complex interference components during friction. Therefore, detecting accurate "weak" friction-induced vibration is key to using it entirely. A method based on the correlation between friction-induced vibration and sound signals was proposed to achieve this goal. The ball–disk wear experiments were conducted under oil lubrication using a wear tester. Vibration and sound pressure signals generated during the experiments were recorded. By the spectrum analysis of the cross-correlation function calculated from the two types of signals, the "weak" FIV components submerged in the original signals were detected. The experimental results showed that the root mean square change of the "weak" friction-induced vibration detected in the vibration and sound pressure signals was highly consistent with the friction coefficient change. It could effectively characterize the transition of the wear stage from running-in to stable wear of the friction pairs. Therefore, the cross-correlation analysis of vibration and sound signals could be a reliable tool for detecting the "weak" friction-induced vibration. [ABSTRACT FROM AUTHOR]

The compaction mechanism of titanium hydride powder is an important issue because it has a direct impact on density and strength of green compacts and ultimately on the physical and mechanical properties of a final sintered products. In this paper, the characteristics and compaction behavior of titanium hydride and hydrogenation-dehydrogenation titanium powders are comparatively studied and analyzed for better understanding of compaction mechanism of brittle low-strength titanium hydride. The results indicate that the particles of titanium hydride powder are easily crushed under compaction loading at relatively low pressure well below compression strength of bulk titanium hydride, the degree of particle crushed increases with the increase of pressure. The compaction behavior of titanium hydride powder mainly includes the rearrangement and crushing of particles in the early compaction stage, minor plastic deformation, if any, and further rearrangement of particle fragments with filling the pores in the later stage. Such compaction behavior provides relative density of green hydride compacts higher than that for titanium powder of the same size. The relatively coarse titanium hydride powder with wide particle size distribution is easier to fill the pores providing highest green density. [ABSTRACT FROM AUTHOR]

On the basis of the composition of organs and static theory, a bionic periodic isolation structure is modeled to study the mechanical characteristics of vibration isolation with the aim of isolating ship vibration. The unit cell of the structure is composed of three layers, an upper steel layer, a middle stiff rubber layer, and a bottom soft rubber layer, and some multicell units are analyzed. To maintain numerical accuracy, the mapping method is used to mesh the periodic model with an element size of 0.01 mm. In the case of a static load, all the unit cells exhibit bulging deformation on two sides. The maximum deformation is not always at the upper layer, with the maximum bulging at two sides in the single-cell case and deformation in the middle layer in the cases of 9 and 10 cells. When the number of cells is above 6, deformation is enhanced in the middle layer, with half a sinusoidal wave. In this paper, the deformation ratio in the middle layer is as high as 87.99%. In addition, the stress distribution characteristic is also compared among some cases. The bionic isolation structure and its analysis may provide a new way to reduce the vibration in a ship. [ABSTRACT FROM AUTHOR]

This study investigated the influence of nitrogen (N) fertilizer and straw on intact amino acid N uptake by soil microorganisms and the relationship between amino acid turnover and soil properties during the wheat growing season. A wheat pot experiment was carried out with three treatments: control (CK), N fertilizer (NF) and N fertilizer plus rice straw (NS). We used stable isotope compound-specific analysis to determine the uptake of 13C,15N-glycine by soil microorganisms. In the NF treatment, microbial 13C,15N-glycine uptake was lower compared with CK, suggesting that inorganic N was the preferred N source for soil microorganisms. However, The application of straw with N fertilizer (in NS treatment) increased microbial 13C,15N-glycine uptake even with the same amount of N fertilizer application. In this treatment, enzyme activities, soil microbial biomass C and microbial biomass N increased simultaneously because more C was available. Soil mineral N and plant N contents all decreased substantially. The increased uptake of intact 13C,15N-glycine in the NS treatment can be attributed to direct assimilation by soil microorganisms to satisfy the demand for N when inorganic N was consumed. [ABSTRACT FROM AUTHOR]

In the present study, 98.6–99.5% dense in situ reinforced Ti6Al4V/TiB composites were manufactured with a newly developed approach based on hydrogen-assisted blended elemental powder metallurgy (BEPM). The approach includes the activation milling of titanium powder produced with hydrogenation-dehydrogenation (HDH-Ti powder) with finer TiB2 additives, following blending with TiH2 and master alloy (MA) powders, and final press-and-sinter operations. Scanning electron microscope (SEM) observations prove the formation of microstructures with improved density and homogeneous distribution of TiB reinforcements in a sintered Ti6Al4V matrix. Hardness and compressive tests validated the high mechanical characteristics of produced composites. The effect of preliminary milling time over 2–6 h and the ratio of hydrogenated and non-hydrogenated titanium powders used (TiH2 vs. HDH Ti) on microstructure and mechanical properties were studied to further optimize the processing parameters. Test results indicate the above approach can be regarded as a promising route for the cost-effective manufacturing of Ti6Al4V/TiB composite with reduced porosity, tailored microstructure uniformity, acceptable impurity level and, hence, mechanical characteristics sufficient for practice applications. [ABSTRACT FROM AUTHOR]

External organic nitrogen (N) inputs can contrastingly affect the transformation and availability of N in forest soils, which is an important potential N resource and is possibly vulnerable to soil properties. Little is known about the transformation and availability of external small molecule organic N in forest soils and the underlying microbial mechanisms. Soil samples from Changbai Mountain at different altitudes (from 750 m to 2200 m) that ranged widely in soil properties were incubated with 13C, 15N-labeled glycine. The fate of 15N-glycine and the incorporation of 13C into different phospholipid fatty acids (PLFAs) were measured at the same time. The addition of glycine promoted gross N mineralization and microbial N immobilization significantly. Mineralization of glycine N accounted for 6.2–22.5% of the added glycine and can be explicable in the light of a readily mineralizable substrate by soil microorganisms. Assimilation of glycine N into microbial biomass by the mineralization-immobilization-turnover (MIT) route accounted for 24.7–52.1% of the added label and was most mightily affected by the soil C/N ratio. We also found that the direct utilization of glycine is important to fulfill microorganism growth under the lack of available carbon (C) at upper elevations. The labeled glycine was rapidly incorporated into the PLFAs and was primarily assimilated by bacteria, indicating that different groups of the microbial community were answerable to external organic N. G+ bacteria were the main competitors for the exogenous glycine. Increased intact incorporation of glycine into microbial biomass and the concentration of PLFAs in general, particularly in G+ bacteria, suggest a diversified arrangement to response changes in substrate availability. [ABSTRACT FROM AUTHOR]